Similar experimental study on diffusion and distribution of diesel exhaust in confined space of a coal mine.

In the confined space of the underground coal mine, which is dominated by transportation lanes, explosion-proof diesel-powered trackless rubber-wheeled vehicles are becoming the main transportation equipment, and the exhaust gas produced by them is hazardous to the health of workers and pollutes the underground environment. In this experiment, a similar test platform is built to study the effects of wind speed, vehicle speed, and different wind directions on the diffusion characteristics of exhaust gas. In this paper, CO and SO2 are mainly studied. The results show that the diffusion of CO and SO2 gas is similar and the maximum SO2 concentration only accounts for 11.4% of the CO concentration. Exhaust gas is better diluted by increasing the wind speed and vehicle speed, respectively. Downwind is affected by the reverse wind flow and diffuses to the driver's position, which is easy to cause occupational diseases. When the wind is a headwind, the exhaust gases spread upwards and make a circumvention movement, gathering at the top. When the wind speed and vehicle speed are both 0.6 m/s, the CO concentration corresponds to the change trend of the Lorentz function when the wind is downwind and the CO concentration corresponds to the change trend of the BiDoseResp function when the wind is headwind. The study of exhaust gas diffusion characteristics is of great significance for the subsequent purification of the air in the restricted mine space and the protection of the workers' occupational health.

[Status of occupational exposure limits of air toxic substances in the GESTIS Substances Database].

Objective: In order to understand the current situation of air toxic substances without occupational exposure limits (OELs) in the workplace in the Germany GESTIS Substance Database, and to provide an effective reference for formulating OELs of corresponding toxic substances and improving health standards. Methods: From March 2022 to May 2023, based on the standard of GBZ 2.1-2019 Occupational Exposure Limits for Hazardous Agents in the Workplace-Part 1: Chemical Hazardous Agents, air toxic substances without OELs in the standard of GBZ/T 300.1-2017 Determination of Toxic Substances in Workplace Air-Part 1: General Principles were screened out, then corresponding OELs in other countrie/regions were queried through the Germany GESTIS Substance Database. Results: Among the 333 kinds (classes) of air toxic substances in 160 parts of GBZ/T 300.1-2017 standard, 48 kinds (classes) of air toxic substances were screened out and had not yet been formulated OELs in GBZ 2.1-2019 standard. By querying the Germany GESTIS Substance Database, it was found that among the 48 kinds (classes) of air toxic substances, 35 kinds (classes) of air toxic substances had both 8-hour occupational exposure limit and short-term occupational exposure limit, 4 kinds (classes) of air toxic substances had 8-hour occupational exposure limit but no short-term occupational exposure limit, 9 kinds (classes) of air toxic substances hadn't been retrieved any OELs. In addition, standard test methods of 7 kinds of air toxic substances hadn't been published in the present, including trimethylchlorosilane, trimethylbenzenes, cumene, chloroethane, chloropropane, dibromoethane and acetophenone. Conclusion: In the process of formulating or revising the standards of GBZ 2.1-2019 and GBZ/T 300, the latest published OELs in the Germany GESTIS Substance Database could be used as a reference basis.

[Establishment of collection methods and laboratory testing methods for active pharmaceutical ingredient in the workplace air].

Objective: To establish collection methods and laboratory testing methods for qualitative and quantitative analysis of 9 typical active pharmaceutical ingredient in the workplace air. Methods: In December 2021, a mixed solution of nine analytes was prepared and then dispersed in aerosol state to simulate sampling. Glass fiber filter membrane was selected as air collector and collected active pharmaceutical ingredient in the air at a rate of 2.0 L/min for 15 minutes. Then, the obtained filter membrane samples were eluted with 25%ACN/75%MeOH. Finally, the eluent was qualitatively and quantitatively analyzed with liquid chromatography-triple quadrupole mass spectrometer. Results: This method could effectively collect active pharmaceutical ingredient in the air, with an average sampling efficiency of more than 98.5%. The linear correlation coefficient r was greater than 0.9990. The lower limit of quantification for each analyte ranged from 0.6~500.0 ng/ml, and the average recovery rate ranged from 97.6%~102.5%. Conclusion: This method could simultaneously collect 9 active pharmaceutical ingredient in the workplace air, and could provide accurate qualitative and quantitative analysis in subsequent laboratory tests.

Benzene Exposure in Workers From a Waste Oil Regeneration Plant During Ordinary Activities by Air and Biological Monitoring.

BACKGROUND: In the regeneration of waste oil, a strategical technological process for the European Union circular economy action plan, exhausted oils are regenerated to produce high performing oil bases. Aim of this work was to assess the exposure to benzene in plant workers during ordinary activities. METHODS: 59 workers, potentially exposed to benzene, and 9 administrative workers from an Italian plant were monitored for the whole work shift with personal air samplers; urinary benzene (BEN-U) and S-phenyl mercapturic acid (SPMA) were measured by mass spectrometry methods in end-shift urine samples. Different job tasks were identified among workers. RESULTS: Median (minimum-maximum) airborne exposures to benzene were <0.9 (<0.9-6.3) and <0.9 (<0.9-0.9) µg/m3, BEN-U and SPMA levels were 0.094 (<0.015-3.095) µg/L and 0.15 (<0.10-9.67) µg/g crt and 0.086 (0.034-0.712) µg/L and <0.10 (<0.10-3.19) µg/g creatinine in workers and administrative workers, respectively. No differences were found among job tasks and between workers and administrative workers, while higher levels were found in smokers than in non-smokers. For all job tasks, the exposure to benzene was always below occupational limit values. CONCLUSIONS: This study has investigated for the first time the exposure to benzene of workers employed in the re-refining of exhaust oil. The results showed that normal production activities in regenerating used oils do not pose a risk of exposure to benzene in workers.

Source Apportionment of Particulate Matter in a Metal Workshop.

Metal workshops are workplaces with the substantial production of particulate matter (PM) with high metal content, which poses a significant health risk to workers. The PM produced by different metal processing techniques differs considerably in its elemental composition and size distribution and therefore poses different health risks. In some previous studies, the pollution sources were isolated under controlled conditions, while, in this study, we present a valuable alternative to characterize the pollution sources that can be applied to real working environments. Fine PM was sampled in five units (partially specializing in different techniques) of the same workshop. A total of 53 samples were collected with a temporal resolution of 30 min and 1 h. The mass concentrations were determined gravimetrically, and the elemental analysis, in which the concentrations of 14 elements were determined, was carried out using the X-ray fluorescence technique. Five sources of pollution were identified: background, steel grinding, metal active gas welding, tungsten inert gas welding, and machining. The sources were identified by positive matrix factorization, a statistical method for source apportionment. The identified sources corresponded well with the work activities in the workshop and with the actual sources described in previous studies. It is shown that positive matrix factorization can be a valuable tool for the identification and characterization of indoor sources.

Evaluation of flow controllers used with evacuated canisters to assess VOC exposures in occupational and non-occupational environments.

Ideally, measuring exposures to volatile organic compounds should allow for modifying sampling duration without loss in sensitivity. Traditional sorbent-based sampling can vary sampling duration, but sensitivity may be affected when capturing shorter tasks. Diaphragm and capillary flow controllers allow for a range of flow rates and sampling durations for air sampling with evacuated canisters. The goal of this study was to evaluate the extent to which commercialized capillary flow controllers satisfy the bias (±10%) and accuracy (±25%) criteria for air sampling methods as established by the National Institute for Occupational Safety and Health (NIOSH) using the framework of ASTM D6246 Standard Practice for Evaluating the Performance of Diffusive Samplers to compare their performance with diaphragm flow controllers in a long-term field study. Phase 1 consisted of a series of laboratory tests to evaluate capillary flow controller flow rates with respect to variations in temperature (-15-24 °C). The results demonstrated a slight increase in flow rate with lower temperatures. In Phase 2, the capillary flow controller was evaluated utilizing a matrix of parameters, including time-weighted average concentration, peak concentration (50-100× base concentration), air velocity across the sampler inlet (0.41-0.5 m/s), relative humidity (20-80%), and temperature (10-32 °C). Comparison of challenge concentrations with reference concentrations revealed the aggregate bias and overall accuracy for four tested compounds to be within the range of criteria for both NIOSH and ASTM standards. Additionally, capillary flow controllers displayed lower variability in flow rate and measured concentration (RSD: 2.4% and 4.3%, respectively) when compared with diaphragm flow controllers (RSD: 6.9% and 7.2%, respectively) for 24-hr laboratory tests. Phase 3 involved further testing of flow rate variability for both diaphragm and capillary flow controllers in a field study. The capillary flow controller displayed a lower level of variability (RSD: 5.2%) than the diaphragm flow controller (RSD: 8.0%) with respect to flow rate, while allowing for longer durations of sampling.

Thin seams and small mines are associated with higher exposures to respirable crystalline silica in US underground coal mines.

OBJECTIVES: Previous radiologic and histopathologic studies suggest respirable crystalline silica (RCS) overexposure has been driving the resurgence of pneumoconiosis among contemporary US coal miners, with a higher prevalence of severe disease in Central Appalachia. We sought to better understand RCS exposure among US underground coal miners. METHODS: We analysed RCS levels, as measured by respirable quartz, from coal mine dust compliance data from 1982 to 2021. RESULTS: We analysed 322 919 respirable quartz samples from 5064 US underground coal mines. Mean mine-level respirable quartz percentage and mass concentrations were consistently higher for Central Appalachian mines than the rest of the USA. Mean mine-level respirable quartz mass concentrations decreased significantly over time, from 0.116 mg/m3 in 1982 to as low as 0.017 mg/m3 for Central Appalachian mines, and from 0.089 mg/m3 in 1983 to 0.015 mg/m3 in 2020 for the rest of the USA. Smaller mine size, location in Central Appalachia, lack of mine safety committee and thinner coal seams were predictive of higher respirable quartz mass concentrations. CONCLUSIONS: These data substantially support the association between RCS overexposure and the resurgence of coal workers' pneumoconiosis in the USA, particularly in smaller mines in Central Appalachia.

Bioaerosol Exposures and Respiratory Diseases in Cannabis Workers.

PURPOSE OF REVIEW: This review investigates occupational inhalation hazards associated with biologically derived airborne particles (bioaerosols) generated in indoor cannabis cultivation and manufacturing facilities. RECENT FINDINGS: Indoor cannabis production is growing across the US as are recent reports of respiratory diseases among cannabis workers, including occupational asthma morbidity and mortality. More information is needed to understand how bioaerosol exposure in cannabis facilities impacts worker health and occupational disease risk. Preliminary studies demonstrate a significant fraction of airborne particles in cannabis facilities are comprised of fungal spores, bacteria, and plant material, which may also contain hazardous microbial metabolites and allergens. These bioaerosols may pose pathogenic, allergenic, toxigenic, and pro-inflammatory risks to workers. The absence of multi-level, holistic bioaerosol research in cannabis work environments necessitates further characterization of the potential respiratory hazards and effective risk prevention methods to safeguard occupational health as the cannabis industry continues to expand across the US and beyond.

Nail salon dust reveals alarmingly high photoinitiator levels: Assessing occupational risks.

Photoinitiators (PIs) are chemical additives that generate active substances, such as free radicals to initiate photopolymerization. Traditionally, polymerization has been considered a green technique that seldomly generates contaminants. However, many researches have confirmed toxicity effects of PIs, such as carcinogenicity, cytotoxicity, endocrine disrupting effects. Surprisingly, we found high levels of PIs in indoor dust. Our analysis revealed comparable levels of PIs in dust from printing shops (geometric mean, GM: 1.33 ×103 ng/g) and control environments (GM: 874 ng/g), underscoring the widespread presence of PIs across various settings. Alarmingly, in dust samples from nail salons, PIs were detected at total concentrations ranging from 610 to 1.04 × 107 ng/g (GM: 1.87 ×105 ng/g), significantly exceeding those in the control environments (GM: 1.43 ×103 ng/g). Nail salon workers' occupational exposure to PIs through dust ingestion was estimated at 4.86 ng/kg body weight/day. Additionally, an in vitro simulated digestion test suggested that between 10 % and 42 % of PIs present in ingested dust could become bioaccessible to humans. This is the first study to report on PIs in the specific environments of nail salons and printing shops. This study highlights the urgent need for public awareness regarding the potential health risks posed by PIs to occupational workers, marking an important step towards our understanding of environmental pollution caused by PIs.

Association between exposure to metalworking fluid aerosols, occupational noise and chronic kidney disease: a cross-sectional study in China.

BACKGROUND: Chronic kidney disease (CKD) carries a high public health burden yet little is known about the relationship between metalworking fluid (MWF) aerosols, occupational noise and CKD. We aimed to explore the relationship between occupational MWF aerosols, occupational noise and CKD. METHODS: A total of 2,738 machinists were sampled from three machining companies in Wuxi, China, in 2022. We used the National Institute for Occupational Safety and Health (NIOSH) method 5524 to collect individual samples for MWF aerosols exposure, and the Chinese national standard (GBZ/T 189.8-2007) method to test individual occupational noise exposure. The diagnostic criteria for CKD were urinary albumin/creatinine ratio (UACR) of ≥ 30 mg/g and reduced renal function (eGFR < 60 mL.min- 1. 1.73 m- 2) lasting longer than 3 months. Smooth curve fitting was conducted to analyze the associations of MWF aerosols and occupational noise with CKD. A segmented regression model was used to analyze the threshold effects. RESULTS: Workers exposed to MWF aerosols (odds ratio [OR] = 2.03, 95% confidence interval [CI]: 1.21-3.41) and occupational noise (OR = 1.77, 95%CI: 1.06-2.96) had higher prevalence of CKD than nonexposed workers. A nonlinear and positive association was found between increasing MWF aerosols and occupational noise dose and the risk of CKD. When daily cumulative exposure dose of MWF aerosols exceeded 8.03 mg/m3, the OR was 1.24 (95%CI: 1.03-1.58), and when occupational noise exceeded 87.22 dB(A), the OR was 1.16 (95%CI: 1.04-1.20). In the interactive analysis between MWF aerosols and occupational noise, the workers exposed to both MWF aerosols (cumulative exposure ≥ 8.03 mg/m3-day) and occupational noise (LEX,8 h ≥ 87.22 dB(A)) had an increased prevalence of CKD (OR = 2.71, 95%CI: 1.48-4.96). MWF aerosols and occupational noise had a positive interaction in prevalence of CKD. CONCLUSIONS: Occupational MWF aerosols and noise were positively and nonlinearly associated with CKD, and cumulative MWF aerosols and noise exposure showed a positive interaction with CKD. These findings emphasize the importance of assessing kidney function of workers exposed to MWF aerosols and occupational noise. Prospective and longitudinal cohort studies are necessary to elucidate the causality of these associations.

Characterization of fire investigators' polyaromatic hydrocarbon exposures using silicone wristbands.

BACKGROUND: Exposures to polyaromatic hydrocarbons (PAHs) contribute to cancer in the fire service. Fire investigators are involved in evaluations of post-fire scenes. In the US, it is estimated that there are up to 9000 fire investigators, compared to approximately 1.1 million total firefighting personnel. This exploratory study contributes initial evidence of PAH exposures sustained by this understudied group using worn silicone passive samplers. OBJECTIVES: Evaluate PAH exposures sustained by fire investigators at post-fire scenes using worn silicone passive samplers. Assess explanatory factors and health risks of PAH exposure at post-fire scenes. METHODS: As part of a cross-sectional study design, silicone wristbands were distributed to 16 North Carolina fire investigators, including eight public, seven private, and one public and private. Wristbands were worn during 46 post-fire scene investigations. Fire investigators completed pre- and post-surveys providing sociodemographic, occupational, and post-fire scene characteristics. Solvent extracts from wristbands were analyzed via gas chromatography-mass spectrometry (GC-MS). Results were used to estimate vapor-phase PAH concentration in the air at post-fire scenes. RESULTS: Fire investigations lasted an average of 148 minutes, standard deviation ± 93 minutes. A significant positive correlation (r=0.455, p<.001) was found between investigation duration and PAH concentrations on wristbands. Significantly greater time-normalized PAH exposures (p=0.039) were observed for investigations of newer post-fire scenes compared to older post-fire scenes. Regulatory airborne PAH exposure limits were exceeded in six investigations, based on exposure to estimated vapor-phase PAH concentrations in the air at post-fire scenes. DISCUSSION: Higher levels of off-gassing and suspended particulates at younger post-fire scenes may explain greater PAH exposure. Weaker correlations are found between wristband PAH concentration and investigation duration at older post-fire scenes, suggesting reduction of off-gassing PAHs over time. Exceedances of regulatory PAH limits indicate a need for protection against vapor-phase contaminants, especially at more recent post-fire scenes.

Exposure to occupational air pollution and vascular endothelial dysfunction in workers of the steel industry in Iran.

Air pollution is recognized as a risk factor for cardiovascular diseases; however, the precise underlying mechanisms remain unclear. This study investigated the impact of occupational air pollution exposure on endothelial function in workers within the steel industry. Specifically, we examined male employees in the coke-making division of the Isfahan Steel Company in Iran, as well as those in administrative roles with no known history of cardiovascular risk. Data on age, body mass index, duration of employment, blood pressure, fasting blood sugar, and lipid profile were collected. To assess endothelial function, flow-mediated dilation (FMD) was measured. The baseline brachial artery diameter was greater (mean difference [95% CI] = 0.068 mm [0.008 to 0.128]), while the FMD was lower (mean difference [95% CI] = -0.908 % [-1.740 to -0.075]) in the coke-making group than in the control group. After controlling for potential confounding variables, it was observed that working in the coke-making sector of the industry was associated with lower FMD (F = 3.954, p = .049). These findings indicated that occupational air pollution exposure among workers in the steel industry is linked to impaired endothelium-dependent vasodilation.

Association between exposure to airborne trichloramine and health effects in indoor swimming pool workers.

OBJECTIVE: The main objective of this study was to comprehensively investigate the association between trichloramine (TCA) exposure and respiratory health effects in swimming pool workers. METHODOLOGY: In this study, air sampling was performed for TCA concentrations at fixed locations (static measurements) and on individual workers (personal measurements) in six indoor public swimming pools during periods of high swimmer attendance over the winter school break. Health effects were evaluated using questionnaires and fractional exhaled nitric oxide (FENO) tests performed before and after the working day. RESULTS: In these swimming pools, the environmental TCA concentration ranged from 0.11 to 0.88 mg/m³. Worker exposure ranged from 0.05 to 0.72 mg/m³ for personal measurements. Furthermore, in each swimming pool, the average worker exposure to TCA exceeded the recommended occupational exposure limit of 0.35 mg/m³. Personal TCA measurements were consistently lower than static measurements performed around the pool, with a reduction ranging from 21% to 49%. This can be explained by the time that the workers spend in the pool area, office, and break room. The most common respiratory health effects self-reported by the workers were coughing, shortness of breath, and sneezing with prevalence rates of 38%, 37%, and 35%, respectively. This study demonstrated an association between TCA exposure and eye irritation. Analysis of the FENO tests revealed that individuals with preexisting asthma or allergies exhibited sustained FENO elevation. CONCLUSION: The findings suggest that occupational exposure to TCA in indoor swimming pools is a matter of concern. Implementing and improving workplace safety measures is crucial for safeguarding the respiratory health of swimming pool workers.

Associations of multiple hydroxy-polycyclic aromatic hydrocarbons with serum levels of lipids in the workers from coking and non-ferrous smelting industries.

Epidemiological evidence indicates that exposure to polycyclic aromatic hydrocarbons (PAHs) is associated with certain metabolic diseases. However, the relationship between PAHs and serum lipid profiles in exposed subjects remain unknown. Herein, the associations of multiple (8) urinary hydroxylated PAHs (OH-PAHs) in workers of coking (n = 655) and non-ferrous smelting (n = 614) industries with serum lipid levels (marking lipid metabolism) were examined. Multivariable linear regression, Bayesian kernel machine regression, and quantile g-computation were used. Most urinary OH-PAHs were significantly higher (p < 0.001) in coking workers than in non-ferrous smelting workers. In workers of both industries, OH-PAH exposure was associated with elevated levels of serum total cholesterol, total triglyceride, and low-density lipoprotein, as well as reduced high-density lipoprotein levels. Specifically, urinary 4-hydroxyphenanthrene was significantly positively associated with serum total cholesterol, total triglyceride, and low-density lipoprotein levels in non-ferrous smelting workers; however, the completely opposite association of 4-hydroxyphenanthrene with these lipid levels was observed in coking workers. The results of this pioneering examination suggest that exposure to OH-PAHs may contribute to dyslipidemia in coking and non-ferrous smelting workers, and distinct patterns of change were observed. Further prospective studies involving larger sample sizes are needed to further validate the findings.

Impact of air quality on the health of present-day workers in an Asbestos roof manufacturing industry, Sri Lanka.

The study's objective was to determine the air quality in an asbestos-related industry and its impact on current workers' respiratory health. Seventy-seven air and 65 dust samples were collected at 5-day intervals in an asbestos roofing sheets production factory in Sri Lanka having two production facilities. Sampling was performed in ten sites: Defective sheets-storage, Production-plant, Pulverizer, Cement-silo, and Loading-area. A detailed questionnaire and medical screening were conducted on 264 workers, including Lung Function Tests (LFT) and chest X-rays. Asbestos fibres were observed in deposited dust samples collected from seven sites. Free chrysotile fibres were absent in the breathing air samples. Scanning Electron Microscopy confirmed the presence of asbestos fibres, and the Energy Dispersive X-ray analysis revealed Mg, O, and Si in depositions. The average concentrations of trace metals were Cd-2.74, Pb-17.18, Ni-46.68, Cr-81.01, As-7.12, Co-6.77, and Cu-43.04 mg/kg. The average Zn, Al, Mg, and Fe concentrations were within 0.2-163 g/kg. The highest concentrations of PM2.52.5 and PM1010, 258 and 387 µg/m3, respectively, were observed in the Pulverizer site. Forty-four workers had respiratory symptoms, 64 presented LFT abnormalities, 5 indicated chest irregularities, 35.98% were smokers, and 37.5% of workers with abnormal LFT results were smokers. The correlation coefficients between LFT results and work duration with respiratory symptoms and work duration and chest X-ray results were 0.022 and 0.011, respectively. In conclusion, most pulmonary disorders observed cannot directly correlate to Asbestos exposure due to negligible fibres in breathing air, but fibres in the depositions and dust can influence the pulmonary health of the employees.

Tracking bioaerosol exposure among municipal solid waste workers using hematological and inflammatory biomarkers.

High levels of bioaerosols may exist in the air of municipal solid waste (MSW) management facilities, constituting a significant occupational hazard for workers. In this study, we investigated the potential association between exposure to bioaerosols and inflammatory biomarkers among municipal solid waste workers (MSWWs) at both the landfill site and the municipal solid waste transfer station (MSWTS), in comparison to a control group without exposure. Air sampling was conducted at six points around the landfill, two points at the MSWTS, and one point in a public park (as a control area) during the spring and summer of 2019. The results of our study revealed that airborne pathogens were highly prevalent at the sampling points, especially in the active zone and leachate collection pond. Aspergillus species were the predominant fungal species detected in this study, with the highest occurrence observed for Aspergillus flavus (83.3%), Aspergillus niger, and Aspergillus fumigatus (75.0%). Furthermore, Staphylococcus species accounted for over 75% of the total bacterial bioaerosols detected across all study areas. The blood test results of workers revealed a significant increase in platelets (PLT), immunoglobulin G (IgG), white blood cells (WBC), neutrophils, basophils, and high-sensitivity C-reactive protein (hs-CRP) compared to the control group. Conversely, platelet distribution width (PDW), mean platelet volume (MPV), and platelet-large cell ratio (P-LCR) in the exposed subjects exhibited a decreasing trend compared to the control group. These findings suggest a potential association between exposure to bioaerosols, particularly in the vicinity of open dumpsites, and elevated levels of hematologic and inflammatory markers in circulation. Furthermore, the influence of smoking status and confounding factors appears to be significant in both the control and exposure groups.

Cross-shift changes in pulmonary function and occupational exposure to particulate matter among e-waste workers in Ghana.

Introduction: Little is known on the association between cross-shift changes in pulmonary function and personal inhalation exposure to particulate matter (PM) among informal electronic-waste (e-waste) recovery workers who have substantial occupational exposure to airborne pollutants from burning e-waste. Methods: Using a cross-shift design, pre- and post-shift pulmonary function assessments and accompanying personal inhalation exposure to PM (sizes <1, <2.5 µm, and the coarse fraction, 2.5-10 µm in aerodynamic diameter) were measured among e-waste workers (n = 142) at the Agbogbloshie e-waste site and a comparison population (n = 65) in Accra, Ghana during 2017 and 2018. Linear mixed models estimated associations between percent changes in pulmonary function and personal PM. Results: Declines in forced expiratory volume in one second (FEV1) and forced vital capacity (FVC) per hour were not significantly associated with increases in PM (all sizes) among either study population, despite breathing zone concentrations of PM (all sizes) that exceeded health-based guidelines in both populations. E-waste workers who worked "yesterday" did, however, have larger cross-shift declines in FVC [-2.4% (95%CI: -4.04%, -0.81%)] in comparison to those who did not work "yesterday," suggesting a possible role of cumulative exposure. Discussion: Overall, short-term respiratory-related health effects related to PM exposure among e-waste workers were not seen in this sample. Selection bias due to the "healthy worker" effect, short shift duration, and inability to capture a true "pre-shift" pulmonary function test among workers who live at the worksite may explain results and suggest the need to adapt cross-shift studies for informal settings.

A study of inflammatory biomarkers in crystalline silica exposed rock drillers.

BACKGROUND: Crystalline silica (CS) exposure can cause serious lung disease in humans, but mechanisms of pulmonary toxicity have not been completely elucidated. AIMS: To assess pro-inflammatory and anti-inflammatory biomarkers and biomarkers related to the development of chronic obstructive pulmonary disease and fibrosis in serum of rock drillers exposed to CS. METHODS: Rock drillers (N = 123) exposed to CS and non-specified particulate matter (PM) were compared to 48 referents without current or past exposure to PM in a cross-sectional study. RESULTS: The rock drillers had been exposed to CS for 10.7 years on average. Geometric mean (GM) current exposure was estimated to 36 µg/m3. Their GM concentration of matrix metalloproteinase 12 (MMP-12) was significantly higher (16 vs. 13 ng/L; p = 0.04), while interleukin (IL) 6 and IL-8 were significantly lower compared to the referents. Also pentraxin 3 was significantly lower (3558 vs. 4592 ng/L; p = 0.01) in the rock drillers. A dose-response relationship was observed between cumulative exposure to CS and MMP-12, the highest exposed subgroup having significantly higher MMP-12 concentrations than the referents. CONCLUSION: Exposure to CS may increase circulating MMP-12 concentrations in a dose-response related fashion. The results may also suggest a down-regulation of pro-inflammatory pathways.

Asbestos exposures associated with the use and handling of drilling mud additives.

This paper summarizes historical asbestos exposure data collected during the handling of short-fiber chrysotile asbestos that was used as an additive to drilling fluid in oil and gas exploration. A total of 1171 industrial hygiene (IH) personal and area air samples were collected and analyzed from more than 20 drilling rigs between 1972 and 1985. The dataset consists of 1097 short-term samples (<240 min) with more than 80% having sample durations less than 30 min. Average airborne fiber concentrations measured during asbestos handling activities ranged from 0.62 f/cc to 3.39 f/cc using phase-contrast microscopy (PCM). An additional 14 samples were considered long-term samples (>240 min) and there were 60 samples with no reported sample duration. Eight-hour time-weighted average (8-h TWA) results, calculated using short-term samples, along with long-term samples greater than 240 min, did not exceed contemporaneous Occupational Safety and Health Administration (OSHA) permissible exposure limits (PELs). This analysis fills a data gap in the evaluation of asbestos exposures from the use of drilling mud additives (DMAs) that contained chrysotile asbestos.

Fungal and bacterial species on biowaste workers' hands and inhalation zone, and potential airway deposition.

This study aims to investigate the microbiological working environment of biowaste workers, focusing on airborne fungal and bacterial species exposure, size distribution, and species on workers' hands. The research, conducted across six plants with 45 personal exposure assessments, revealed a total of 150 bacterial species and 47 fungal species on workers' hands, including 19 and 9 species classified in risk class 2 (RC2), respectively. Workers' exposure analysis identified 172 bacterial and 32 fungal species, with several in RC2. In work areas, 55 anaerobic bacterial species belonging to RC2 were found. Different species compositions were observed in various particle size fractions, with the highest species richness for anaerobic bacteria in the fraction potentially depositing in the secondary bronchi and for fungi in the pharynx fraction. The geometric mean aerodynamic diameter (DG) of RC2 anaerobic bacteria was 3.9 µm, <1.6 µm for Streptomyces, 3.4 µm for Aspergillus, and 2.0 µm for Penicillium. Overlapping species were identified on workers' hands, in their exposure, and in work areas, with Bacillus amyloliquefaciens, Leuconostoc mesenteroides, Bacillus cereus, Enterococcus casseliflavus, and Aspergillus niger consistently present. While the majority of RC2 bacterial species lacked documented associations with occupational health problems, certain bacteria and fungi, including Bacillus cereus, Escherichia coli, Enterobacter, Klebsiella pneumonia, Aspergillus fumigatus, Aspergillus niger, Aspergillus flavus, Lichtheimia corymbifera, Lichtheimia ramosa, and Paecilomyces variotii, have previously been linked to occupational health issues. In conclusion, biowaste workers were exposed to a wide range of microorganisms including RC2 species which would deposit in different parts of the airways.