Co-removal and recycling of Ba2+ and Ca2+ in hypersaline wastewater based on the microbially induced carbonate precipitation technique: Overlooked Ba2+ in extracellular and intracellular vaterite.

This study investigates the co-precipitation of calcium and barium ions in hypersaline wastewater under the action of Bacillus licheniformis using microbially induced carbonate precipitation (MICP) technology, as well as the bactericidal properties of the biomineralized product vaterite. The changes in carbonic anhydrase activity, pH, carbonate and bicarbonate concentrations in different biomineralization systems were negatively correlated with variations in metal ion concentrations, while the changes in polysaccharides and protein contents in bacterial extracellular polymers were positively correlated with variations in barium concentrations. In the mixed calcium and barium systems, the harvested minerals were vaterite containing barium. The increasing concentrations of calcium promoted the incorporation and adsorption of barium onto vaterite. The presence of barium significantly increased the contents of O-CO, N-CO, and Ba-O in vaterite. Calcium promoted barium precipitation, but barium inhibited calcium precipitation. After being treated by immobilized bacteria, the concentrations of calcium and barium ions decreased from 400 and 274 to 1.72 and 0 mg/L (GB/T15454-2009 and GB8978-1996). Intracellular minerals were also vaterite containing barium. Extracellular vaterite exhibited bactericidal properties. This research presents a promising technique for simultaneously removing and recycling hazardous heavy metals and calcium in hypersaline wastewater.

Enrichment of Trypsin Inhibitor from Soybean Whey Wastewater Using Different Precipitating Agents and Analysis of Their Properties.

Recovering valuable active substances from the by-products of agricultural processing is a crucial concern for scientific researchers. This paper focuses on the enrichment of soybean trypsin inhibitor (STI) from soybean whey wastewater using either ammonium sulfate salting or ethanol precipitation, and discusses their physicochemical properties. The results show that at a 60% ethanol content, the yield of STI was 3.983 mg/mL, whereas the yield was 3.833 mg/mL at 60% ammonium sulfate saturation. The inhibitory activity of STI obtained by ammonium sulfate salting out (A-STI) was higher than that obtained by ethanol precipitation (E-STI). A-STI exhibited better solubility than E-STI at specific temperatures and pH levels, as confirmed by turbidity and surface hydrophobicity measurements. Thermal characterization revealed that both A-STI and E-STI showed thermal transition temperatures above 90 °C. Scanning electron microscopy demonstrated that A-STI had a smooth surface with fewer pores, while E-STI had a rough surface with more pores. In conclusion, there was no significant difference in the yield of A-STI and E-STI (p < 0.05); however, the physicochemical properties of A-STI were superior to those of E-STI, making it more suitable for further processing and utilization. This study provides a theoretical reference for the enrichment of STI from soybean whey wastewater.

The effect of extracellular polymeric substances on MICP solidifying rare earth slags and stabilizing Th and U.

Microbially induced carbonate precipitation (MICP) has been used to cure rare earth slags (RES) containing radionuclides (e.g. Th and U) and heavy metals with favorable results. However, the role of microbial extracellular polymeric substances (EPS) in MICP curing RES remains unclear. In this study, the EPS of Lysinibacillus sphaericus K-1 was extracted for the experiments of adsorption, inducing calcium carbonate (CaCO3) precipitation and curing of RES. The role of EPS in in MICP curing RES and stabilizing radionuclides and heavy metals was analyzed by evaluating the concentration and morphological distribution of radionuclides and heavy metals, and the compressive strength of the cured body. The results indicate that the adsorption efficiencies of EPS for Th (IV), U (VI), Cu2+, Pb2+, Zn2+, and Cd2+ were 44.83%, 45.83%, 53.7%, 61.3%, 42.1%, and 77.85%, respectively. The addition of EPS solution resulted in the formation of nanoscale spherical particles on the microorganism surface, which could act as an accumulating skeleton to facilitate the formation of CaCO3. After adding 20 mL of EPS solution during the curing process (Treat group), the maximum unconfined compressive strength (UCS) of the cured body reached 1.922 MPa, which was 12.13% higher than the CK group. The contents of exchangeable Th (IV) and U (VI) in the cured bodies of the Treat group decreased by 3.35% and 4.93%, respectively, compared with the CK group. Therefore, EPS enhances the effect of MICP curing RES and reduces the potential environmental problems that may be caused by radionuclides and heavy metals during the long-term sequestration of RES.

Macro-characteristics and micro-mechanisms of Na2SO4 precipitation dissolved by KNO3 molten salt in a continuous supercritical water system.

This work aims to explore the ability of molten salt to solve salt deposition in supercritical water (SCW) related technologies including supercritical water oxidation and supercritical water gasification, with KNO3 and Na2SO4 as examples. In the pure KNO3 solution, the two-phase layering of high-density KNO3 molten salt (settling at the reactor bottom) and low-density saturated KNO3-SCW salt solution (flowing out at the top outlet of the reactor) was formed in a kettle-reactor with about 6.5 ratio of depth to inner diameter, thereby improving the accuracy of measured solubilities. The precipitation macro-characteristics of mixed KNO3 and Na2SO4 in SCW were investigated under different feed concentration conditions. The results showed that Na2SO4 deposition on the reactor sidewall could be reduced by more than 90 % when the mass ratio of KNO3 to Na2SO4 in the feed was only 0.167. No visible salt deposition was observed on the sidewall when the ratio was 0.374. All solid deposited salts were converted into the liquid molten salt as the ratio reached 3.341, and thus could easily flow out of the reactor, without plugging. 'Molten salt dissolution' mechanism may provide a more plausible explanation for mixed KNO3 and Na2SO4 in SCW. In addition, the precipitation micro-mechanisms of mixed KNO3 and Na2SO4, and the critical conditions of avoiding sidewall deposition and reactor plugging were proposed. This work is valuable for overcoming the salt deposition problem in SCW-related technologies.

Synergistic biocementation: harnessing Comamonas and Bacillus ureolytic bacteria for enhanced sand stabilization.

Biocementation, driven by ureolytic bacteria and their biochemical activities, has evolved as a powerful technology for soil stabilization, crack repair, and bioremediation. Ureolytic bacteria play a crucial role in calcium carbonate precipitation through their enzymatic activity, hydrolyzing urea to produce carbonate ions and elevate pH, thus creating favorable conditions for the precipitation of calcium carbonate. While extensive research has explored the ability of ureolytic bacteria isolated from natural environments or culture conditions, bacterial synergy is often unexplored or under-reported. In this study, we isolated bacterial strains from the local eutrophic river canal and evaluated their suitability for precipitating calcium carbonate polymorphs. We identified two distinct bacterial isolates with superior urea degradation ability (conductivity method) using partial 16 S rRNA gene sequencing. Molecular identification revealed that they belong to the Comamonas and Bacillus genera. Urea degradation analysis was performed under diverse pH (6,7 and 8) and temperature (15 °C,20 °C,25 °C and 30 °C) ranges, indicating that their ideal pH is 7 and temperature is 30 °C since 95% of the urea was degraded within 96 h. In addition, we investigated these strains individually and in combination, assessing their microbially induced carbonate precipitation (MICP) in silicate fine sand under low (14 ± 0.6 °C) and ideal temperature 30 °C conditions, aiming to optimize bio-mediated soil enhancement. Results indicated that 30 °C was the ideal temperature, and combining bacteria resulted in significant (p ≤ 0.001) superior carbonate precipitation (14-16%) and permeability (> 10- 6 m/s) in comparison to the average range of individual strains. These findings provide valuable insights into the potential of combining ureolytic bacteria for future MICP research on field applications including soil erosion mitigation, soil stabilization, ground improvement, and heavy metal remediation.

High-throughput, low-cost quantification of 11 therapeutic antibodies using caprylic acid precipitation and LC-MS/MS.

BACKGROUND: Therapeutic drug monitoring of treatment with therapeutic antibodies is hampered by the application of a wide range of different methods in the quantification of serum levels. LC-MS based methods could significantly improve comparability of results from different laboratories, but such methods are often considered complicated and costly. We developed a method for LC-MS/MS based quantification of 11 therapeutic antibodies concomitantly measured in a single run, with emphasis on simplicity in sample preparation and low cost. RESULTS: After a single-step sample purification using caprylic acid precipitation to remove interfering proteins, the sample underwent proteolysis followed by LC-MS/MS analysis. Infliximab is used as internal standard for sample preparation while isotope-labeled signature peptides identified for each analyte are internal standards for the LC-MS/MS normalization. The method was validated according to recognized guidelines, and pipetting steps can be performed by automated liquid handling systems. The total precision of the method ranged between 2.7 and 7.3 % (5.1 % average) across the quantification range of 4-256 µg/ml for all 11 drugs, with an average accuracy of 96.3 %. Matrix effects were xamined in 55 individual patient samples instead of the recommended 6, and 147 individual patient samples were screened for interfering compounds. SIGNIFICANCE AND NOVELTY: Our method for simultaneous quantification of 11 t-mAb in human serum allows an unprecedented integration of robustness, speed and reduced complexity, which could pave the way for uniform use in research projects and clinical settings alike. In addition, the first LC-MS protocol for signature peptide-based quantification of durvalumab is described. This high throughput method can be readily adapted to a drug panel of choice.

Microbially induced calcium carbonate precipitation through CO2 sequestration via an engineered Bacillus subtilis.

BACKGROUND: Microbially induced calcium carbonate precipitation has been extensively researched for geoengineering applications as well as diverse uses within the built environment. Bacteria play a crucial role in producing calcium carbonate minerals, via enzymes including carbonic anhydrase-an enzyme with the capability to hydrolyse CO2, commonly employed in carbon capture systems. This study describes previously uncharacterised carbonic anhydrase enzyme sequences capable of sequestering CO2 and subsequentially generating CaCO3 biominerals and suggests a route to produce carbon negative cementitious materials for the construction industry. RESULTS: Here, Bacillus subtilis was engineered to recombinantly express previously uncharacterised carbonic anhydrase enzymes from Bacillus megaterium and used as a whole cell catalyst allowing this novel bacterium to sequester CO2 and convert it to calcium carbonate. A significant decrease in CO2 was observed from 3800 PPM to 820 PPM upon induction of carbonic anhydrase and minerals recovered from these experiments were identified as calcite and vaterite using X-ray diffraction. Further experiments mixed the use of this enzyme (as a cell free extract) with Sporosarcina pasteurii to increase mineral production whilst maintaining a comparable level of CO2 sequestration. CONCLUSION: Recombinantly produced carbonic anhydrase successfully sequestered CO2 and converted it into calcium carbonate minerals using an engineered microbial system. Through this approach, a process to manufacture cementitious materials with carbon sequestration ability could be developed.

Enhanced boron removal via seed-induced crystal growth of barium perborate in sequential fluidized-bed crystallization.

Chemical oxo-precipitation (COP) is an enhanced precipitation method for boron removal with the conversion of boric acid to perborate anions. When using barium-based precipitant, the boron can be effectively precipitated as barium perborates (BaPBs). The phase transformation of BaPBs from amorphous (A-BaPB, Ba(B(OH)3OOH)2) to crystalline (C-BaPB, BaB2(OO)2(OH)4) form is crucial for effective boron removal. However, scaling up this phase transformation of BaPBs is hindered by poor diffusion. This study aims to promote the growth of C-BaPB through seed-induced crystal growth, eliminating the need for phase transformation. By examining the relationship between crystal growth rate and supersaturation, surface spiral growth was identified as the rate-limiting step of the growth of micron-sized seeds near pHpzc. To enable continuous crystal growth, granular seeds of C-BaPB were prepared and employed as the medium for fluidized-bed crystallization (FBC). The system reached steady state 3 hydraulic retention times, achieving 90% boron removal. The effect of surface loading, ionic strength, and dosages on steady-state crystal growth rate was studied, revealing a shift of the rate-limiting step in FBC to diffusion. Lastly, the system that constituted of two FBCs in-series for sequential crystallization of A-BaPB and C-BaPB was demonstrated. The integrated system provided 97.8% of boron removal from synthetic wastewater containing 500 mg-B/L, with 92.3% of boron crystallized on the granular seeds of BaPBs.

Poly(vinyl alcohol)s and Their Glycoderivatives as Efficient Shell-Builders of Nanocapsules by Nanoprecipitation.

Poly(vinyl alcohol)s (PVAs) are very popular dispersants for the construction of colloids and common shell-constituents of microcapsules but remain mostly unexplored as building blocks for the design of nanocapsules through nanoprecipitation or other processes. Herein, we first show that model commercial PVAs and oils can be concomitantly engaged in solvent-shifting procedures to give rise to oil-filled nanocapsules in one step. Next, we report the synthesis of precisely defined water-soluble glyco-PVAs by reversible addition-fragmentation chain transfer (RAFT) copolymerization of 6-O-vinyladipoyl-d-glucopyranose and vinyl chloroacetate and selective alcoholysis reactions. We finally demonstrate that these glycopolymers are excellent candidates for the straightforward conception of oil- and drug-filled, surface- and/or core-tagged, stealth, and degradable nanocapsules by nanoprecipitation.

Ecofriendly solidification of sand using microbially induced calcium phosphate precipitation.

This study introduces microbiologically induced calcium phosphate precipitation (MICPP) as a novel and environmentally sustainable method of soil stabilization. Using Limosilactobacillus sp., especially NBRC 14511 and fish bone solution (FBS) extracted from Tuna fish bones, the study was aimed at testing the feasibility of calcium phosphate compounds (CPCs) deposition and sand stabilization. Dynamic changes in pH and calcium ion (Ca2+) concentration during the precipitation experiments affected the precipitation and sequential conversion of dicalcium phosphate dihydrate (DCPD) to hydroxyapatite (HAp), which was confirmed by XRD and SEM analysis. Sand solidification experiments demonstrated improvements in unconfined compressive strength (UCS), especially at higher Urea/Ca2+ ratios. The UCS values obtained were 10.35 MPa at a ratio of 2.0, 3.34 MPa at a ratio of 1.0, and 0.43 MPa at a ratio of 0.5, highlighting the advantages of MICPP over traditional methods. Microstructural analysis further clarified the mineral composition, demonstrating the potential of MICPP in environmentally friendly soil engineering. The study highlights the promise of MICPP for sustainable soil stabilization, offering improved mechanical properties and reducing environmental impact, paving the way for novel geotechnical practices.

Drug Crystal Precipitation in Biorelevant Bicarbonate Buffer: A Well-Controlled Comparative Study with Phosphate Buffer.

The purpose of the present study was to clarify whether the precipitation profile of a drug in bicarbonate buffer (BCB) may differ from that in phosphate buffer (PPB) by a well-controlled comparative study. The precipitation profiles of structurally diverse poorly soluble drugs in BCB and PPB were evaluated by a pH-shift precipitation test or a solvent-shift precipitation test (seven weak acid drugs (pKa: 4.2 to 7.5), six weak base drugs (pKa: 4.8 to 8.4), one unionizable drug, and one zwitterionic drug). To focus on crystal precipitation processes, each ionizable drug was first completely dissolved in an HCl (pH 3.0) or NaOH (pH 11.0) aqueous solution (450 mL, 50 rpm, 37 °C). A 10-fold concentrated buffer solution (50 mL) was then added to shift the pH value to 6.5 to initiate precipitation (final volume: 500 mL, buffer capacity (ß): 4.4 mM/ΔpH (BCB: 10 mM or PPB: 8 mM), ionic strength (I): 0.14 M (adjusted by NaCl)). The pH, ß, and I values were set to be relevant to the physiology of the small intestine. For an unionizable drug, a solvent-shift method was used (1/100 dilution). To maintain the pH value of BCB, a floating lid was used to avoid the loss of CO2. The floating lid was applied also to PPB to precisely align the experimental conditions between BCB and PPB. The solid form of the precipitants was identified by powder X-ray diffraction and differential scanning microscopy. The precipitation of weak acids (pKa ≤ 5.1) and weak bases (pKa ≥ 7.3) was found to be slower in BCB than in PPB. In contrast, the precipitation profiles in BCB and PPB were similar for less ionizable or nonionizable drugs at pH 6.5. The final pH values of the bulk phase were pH 6.5 ± 0.1 after the precipitation tests in all cases. All precipitates were in their respective free forms. The precipitation of ionizable weak acids and bases was slower in BCB than in PPB. The surface pH of precipitating particles may have differed between BCB and PPB due to the slow hydration process of CO2 specific to BCB. Since BCB is a physiological buffer in the small intestine, it should be considered as an option for precipitation studies of ionizable weak acids and bases.

Coprecipitation of Fe/Cr Hydroxides at Organic-Water Interfaces: Functional Group Richness and (De)protonation Control Amounts and Compositions of Coprecipitates.

Iron/chromium hydroxide coprecipitation controls the fate and transport of toxic chromium (Cr) in many natural and engineered systems. Organic coatings on soil and engineered surfaces are ubiquitous; however, mechanistic controls of these organic coatings over Fe/Cr hydroxide coprecipitation are poorly understood. Here, Fe/Cr hydroxide coprecipitation was conducted on model organic coatings of humic acid (HA), sodium alginate (SA), and bovine serum albumin (BSA). The organics bonded with SiO2 through ligand exchange with carboxyl (-COOH), and the adsorbed amounts and pKa values of -COOH controlled surface charges of coatings. The adsorbed organic films also had different complexation capacities with Fe/Cr ions and Fe/Cr hydroxide particles, resulting in significant differences in both the amount (on HA > SA(-COOH) ≫ BSA(-NH2)) and composition (Cr/Fe molar ratio: on BSA(-NH2) ≫ HA > SA(-COOH)) of heterogeneous precipitates. Negatively charged -COOH attracted more Fe ions and oligomers of hydrolyzed Fe/Cr species and subsequently promoted heterogeneous precipitation of Fe/Cr hydroxide nanoparticles. Organic coatings containing -NH2 were positively charged at acidic pH because of the high pKa value of the functional group, limiting cation adsorption and formation of coprecipitates. Meanwhile, the higher local pH near the -NH2 coatings promoted the formation of Cr(OH)3. This study advances fundamental understanding of heterogeneous Fe/Cr hydroxide coprecipitation on organics, which is essential for successful Cr remediation and removal in both natural and engineered settings, as well as the synthesis of Cr-doped iron (oxy)hydroxides for material applications.

Electron Microscopy for the Stability Assessment of Parenteral Nutrition Admixtures: Focus on Precipitation.

(1) Background: parenteral nutrition (PN) is indispensable for patients unable to receive oral or enteral feeding. However, the complexity of PN solutions presents challenges regarding stability and compatibility. Precipitation reactions may occur. The most frequent is the formation of calcium phosphate (Ca-P). The different factors influencing these reactions must be considered to ensure patient safety. (2) Methods: eight paediatric PN solutions were prepared, following standard protocols. Samples were stored at room temperature and in a refrigerator. Electron microscopy, coupled with energy dispersive X-ray spectroscopy (EDS), was employed. Precipitates were analysed for composition and morphology. (3) Results: precipitates were observed in all samples, even at day 0. Crystalline structures, predominantly composed of calcium or magnesium, sometimes associated with chlorine or phosphorus, were detected. Additionally, amorphous precipitates, contained heterogeneous compositions, including unexpected elements, were identified. (4) Conclusions: various precipitates, primarily calcium- or magnesium-based, can form in PN solutions, although it is not expected that they can form under the real conditions of use. Calcium oxalate precipitation has been characterised, but the use of organic calcium and phosphate salts appears to mitigate calcium phosphate precipitation. Electron microscopy provides interesting results on NP precipitation, but sample preparation may present technical limitations that affect the interpretation of the results.

Addition of sodium malonate alters the morphology and increases the critical flux during tangential flow filtration of precipitated immunoglobulins.

Recent studies have demonstrated that one can control the packing density, and in turn the filterability, of protein precipitates by changing the pH and buffer composition of the precipitating solution to increase the structure/order within the precipitate. The objective of this study was to examine the effect of sodium malonate, which is known to enhance protein crystallizability, on the morphology of immunoglobulin precipitates formed using a combination of ZnCl2 and polyethylene glycol. The addition of sodium malonate significantly stabilized the precipitate particles as shown by an increase in melting temperature, as determined by differential scanning calorimetry, and an increase in the enthalpy of interaction, as determined by isothermal titration calorimetry. The sodium malonate also increased the selectivity of the precipitation, significantly reducing the coprecipitation of DNA from a clarified cell culture fluid. The resulting precipitate had a greater packing density and improved filterability, enabling continuous tangential flow filtration with minimal membrane fouling relative to precipitates formed under otherwise identical conditions but in the absence of sodium malonate. These results provide important insights into strategies for controlling precipitate morphology to enhance the performance of precipitation-filtration processes for the purification of therapeutic proteins.

Effect of biopolymer chitosan on manganese immobilization improvement by microbial­induced carbonate precipitation.

Microbially induced carbonate precipitation (MICP), as an eco-friendly and promising technology that can transform free metal ions into stable precipitation, has been extensively used in remediation of heavy metal contamination. However, its depressed efficiency of heavy metal elimination remains in question due to the inhibition effect of heavy metal toxicity on bacterial activity. In this work, an efficient, low-cost manganese (Mn) elimination strategy by coupling MICP with chitosan biopolymer as an additive with reduced treatment time was suggested, optimized, and implemented. The influences of chitosan at different concentrations (0.01, 0.05, 0.10, 0.15 and 0.30 %, w/v) on bacterial growth, enzyme activity, Mn removal efficiency and microstructure properties of the resulting precipitation were investigated. Results showed that Mn content was reduced by 94.5 % within 12 h with 0.15 % chitosan addition through adsorption and biomineralization as MnCO3 (at an initial Mn concentration of 3 mM), demonstrating a two-thirds decrease in remediation time compared to the chitosan-absent system, whereas maximum urease activity increased by ∼50 %. Microstructure analyses indicated that the mineralized precipitates were spherical-shaped MnCO3, and a smaller size and more uniform distribution of MnCO3 is obtained by the regulation of abundant amino and hydroxyl groups in chitosan. These results demonstrate that chitosan accelerates nucleation and tunes the growth of MnCO3 by providing nucleation sites for mineral formation and alleviating the toxicity of metal ions, which has the potential to upgrade MICP process in a sustainable and effective manner. This work provides a reference for further understanding of the biomineralization regulation mechanism, and gives a new perspective into the application of biopolymer-intensified strategies of MICP technology in heavy metal contamination.

Lipid-based systems with precipitation inhibitors as formulation approach to improve the drug bioavailability and/or lower its dose: a review.

Lipid-based systems, such as self-microemulsifying systems (SMEDDS) are attracting strong attention as a formulation approach to improve the bioavailability of poorly water-soluble drugs. By applying the "spring and parachute" strategy in designing supersaturable SMEDDS, it is possible to maintain the drug in the supersaturated state long enough to allow absorption of the complete dose, thus improving the drug's bio-availability. As such an approach allows the incorporation of larger amounts of the drug in equal or even lower volumes of SMEDDS, it also enables the production of smaller final dosage forms as well as decreased gastrointestinal irritation, being of particular importance when formulating dosage forms for children or the elderly. In this review, the technological approaches used to prolong the drug supersaturation are discussed regarding the type and concentration of polymers used in liquid and solid SMEDDS formulation. The addition of hypromellose derivatives, vinyl polymers, polyethylene glycol, polyoxyethylene, or polymetacrylate copolymers proved to be effective in inhibiting drug precipitation. Regarding the available literature, hypromellose has been the most commonly used polymeric precipitation inhibitor, added in a concentration of 5 % (m/m). However, the inhibiting ability is mainly governed not only by the physicochemical properties of the polymer but also by the API, therefore the choice of optimal precipitation inhibitor is recommended to be evaluated on an individual basis.

Microbiologically induced calcite precipitation (MICP) in situ remediated heavy metal contamination in sludge nutrient soil.

Microbiologically induced calcite precipitation (MICP), as a newly developing bioremediation technology, could redeem heavy metal contamination in diverse scenarios. In this study, MICP bacterium Sporosarcina ureilytica ML-2 was employed to suppress the pollution of Pb, Cd and Zn in municipal sludge nutrient soil. After MICP remediation, the exchangeable Cd and Zn in sludge nutrient soil were correspondingly reduced by 31.02 % and 6.09 %, while the carbonate-bound Pb, Cd and Zn as well as the residual fractions were increased by 16.12 %, 6.63 %, 13.09 % and 6.10 %, 45.70 %, 3.86 %, respectively. In addition, the extractable Pb, Cd and Zn either by diethylenetriaminepentaacetic acid (DTPA) or toxicity characteristic leaching procedure (TCLP) in sludge nutrient soil were significantly reduced. These results demonstrated that the bio-calcite generated via MICP helped to immobilize heavy metals. Furthermore, MICP treatment improved the abundance of functional microorganisms related to urea cycle, while reduced the overall abundance of metal resistance genes (MRGs) and antibiotic resistance genes (ARGs). This work confirmed the feasibility of MICP in remediation of heavy metal in sludge nutrient soil, which expanded the application field of MICP and provided a promising way for heavy metal pollution management.

A study of hydrophobic domain formation of polymeric drug precipitation inhibitors in aqueous solution.

Despite the widespread use of polymers as precipitation inhibitors in supersaturating drug formulations, the current understanding of their mechanisms of action is still incomplete. Specifically, the role of hydrophobic drug interactions with polymers by considering possible supramolecular conformations in aqueous dispersion is an interesting topic. Accordingly, this study investigated the tendency of polymers to create hydrophobic domains, where lipophilic compounds may nest to support drug solubilisation and supersaturation. Fluorescence spectroscopy with the environment-sensitive probe pyrene was compared with atomistic molecular dynamics simulations of the model drug fenofibrate (FENO). Subsequently, kinetic drug supersaturation and thermodynamic solubility experiments were conducted. As a result, the different polymers showed hydrophobic domain formation to a varying degree and the molecular simulations supported interpretation of fluorescence spectroscopy data. Molecular insights were gained into the conformational structure of how the polymers interacted with FENO in solution phase, which apart from nucleation and crystal growth effects, determined drug concentrations in solution. Notable was that even at the lowest polymer concentration of 0.01 %, w/v, there were polymer-specific solubilisation effects of FENO observed and the resulting reduction in apparent drug supersaturation provided relevant knowledge both from a mechanistic and practical perspective.

Protein from tiger nut meal extracted by deep eutectic solvent and alkali-soluble acid precipitation: A comparative study on structure, function, and nutrition.

Protein from tiger nut meal (TNP) performance high nutritional value. This study optimized the extraction parameters for TNP (DES-TNP) using deep eutectic solvent, with HBD: HBA = 5:1, Liquid: Solid = 11:1, and the moisture content was 15 %. A comprehensive comparison was conducted with the protein extracted using alkali-soluble acid precipitation (ASAE-TNP). DES-TNP demonstrated significantly higher purity (76.21 ± 2.59 %) than ASAE-TNP (67.48 ± 1.11 %). Density functional theory confirmed the successful synthesis of DES and its strong interaction with TNP. Moreover, DES-TNP and ASAE-TNP were different in structure (microscopic, secondary, and tertiary) and molecular weight distribution. The discrepancy contributed to the different functional properties, DES-TNP exhibiting better solubility, emulsification and foaming properties at pH13 compared to ASAE-TNP. For nutritional properties, DES-TNP and ASAE-TNP exhibited similar amino acid composition and digestibility, but the total amino acid content of DES-TNP was higher. This study presented a novel method for the extraction and comprehensive utilization of TNP.

Efficient cadmium removal from industrial wastewater generated from smelter using chemical precipitation and oxidation assistance.

The effective treatment of cadmium (Cd) in smelting wastewater is of great industrial importance. This study investigates the efficient removal of Cd from real industrial smelting wastewater via chemical precipitation using a series of experiments. In particular, the effects of different precipitants, agitation conditions, and the addition of NaOCl on Cd removal and pH variation are investigated. CaO (3.75 g/L), NaOH (3.50 g/L), and Ca(OH)2 (3.75 g/L) are found to be effective in elevating the wastewater pH and achieving high Cd removal rates (>99.9%), while the use of NaOH as a precipitant maintains a high Cd removal rate even at low agitation intensities. The properties of the produced sludge and supernatant are also determined using moisture content, particle size, and sludge leaching analyses due to the importance of economic and environmental sustainability in filtration, dewatering, and waste disposal processes. In addition, the addition of 2% NaOCl is tested, revealing that it can improve the Cd removal efficiency of Ca(OH)2, thus potentially reducing processing costs and enhancing the environmental benefits. Overall, these findings offer valuable insights into the removal of Cd from smelting wastewater, with potential implications for both environmental sustainability and economic viability. PRACTITIONER POINTS: CaO, NaOH, and Ca(OH)2 effectively remove Cd (>99.9%) from smelting wastewater. The use of NaOH leads to high Cd removal rates even at low agitation speeds. Adding 2% NaOCl can reduce the Ca(OH)2 dose for more economical Cd removal.