Occurrence, seasonal variations, and fate of household and personal care chemicals in a wastewater treatment plant with Bacillus bioreactor process.

Household and personal care chemicals (HPCCs) constitute a significant component of everyday products, with their global usage on the rise. HPCCs are eventually discharged into municipal wastewater treatment plants (WWTPs). However, the behaviors of HPCCs inside the Bacillus Bioreactor (BBR) process, including their prevalence, fate, and elimination mechanisms, remain underexplored. Addressing this gap, our study delves into samples collected from a BBR process at a significant WWTP in the northeast of China. Our results spotlight the dominance of linear alkylbenzene sulfonates (LASs) in the influent with concentrations ranging between 238 and 789 µg/L, much higher than the other HPCC concentrations, and remained dominant in the subsequent treatment units. After treatment using the BBR process, the concentrations of HPCCs in the effluent were diminished. Examination of different treatment units underscores the grit chamber removed over 60% of higher-concentration HPCCs, while the performance of the (RBC) tank needs to be improved. Except for the ultraviolet radiation (UV)-filters, seasonal variations exert minimal impact on the concentrations and removal efficiencies of other HPCCs in the BBR process. According to the mass balance analysis, the important mechanisms for HPCC removal were biodegradation and sludge adsorption. Also, the octocrylene (OCT) concerns raised by the environmental risk assessment of the HPCCs residuals in the final effluent, indicate a moderate risk to the surrounding aquatic environment (0.1 < RQ < 1), whereas other HPCCs have a lower risk level (RQ < 0.1). Overall, the research offers new perspectives on the fate and elimination mechanisms of HPCCs throughout the BBR process.

Simple and fast microderivatization method for determining formaldehyde using narrow-bore liquid chromatography with UV detection.

Formaldehyde is a harmful substance that can cause sick building syndrome and other diseases, such as contact allergy, asthma, leukemia, cancer, and brain/neuron disorders. Formaldehyde is a ubiquitous chemical owing to its use in many common products, including as a preservative in household and personal care products. To prevent overexposure to formaldehyde, a simple method for determining and controlling the formaldehyde content in commercial products is required. In this study, 3-aminoquinoline (3-AQ) was used to derivatize formaldehyde under mild conditions (2 min at 30 °C) without the use of catalysts or activators. The derivatized sample solutions were separated using narrow-bore liquid chromatography with an ultraviolet (UV) detector in a run time of only 5 min. All sample extraction and derivatization protocols were performed on the microliter scale to reduce the use of organic solvents. The linear range for the determination was 5-1000 µg mL-1, with a detection limit of approximately 1 µg mL-1 (2 ng per 2 µL injection). The proposed microscale method was successfully applied to the analysis of formaldehyde in commercial household products.

Can individual protective measures safeguard cardiopulmonary health from air pollution? A systematic review and meta-analysis.

Evidence supporting the effect of individual protective measures (IPMs) on air pollution is relatively scarce. In this study, we performed a systematic review and meta-analysis to investigate the effects of air purifiers, air-purifying respirators, and cookstove changes on cardiopulmonary health outcomes. We searched PubMed, Scopus, and Web of Science until December 31, 2022, 90 articles and 39,760 participants were included. Two authors independently searched and selected the studies, extracted information, and assessed each study's quality and risk of bias. We performed meta-analyses when three or more studies were available for each IPMs, with comparable intervention and health outcome. Systematic review showed that IPMs were beneficial in children and elderly with asthma along with healthy individuals. Meta-analysis results showed a reduction in cardiopulmonary inflammation using air purifiers than in control groups (with sham/no filter) with a decrease in interleukin 6 by -0.247 µg/mL (95% confidence intervals [CI] = -0.413, -0.082). A sub-group analysis for air purifier as an IPMs in developing counties reduced fractional exhaled nitric oxide by -0.208 ppb (95% confidence intervals [CI] = -0.394, -0.022). However, evidence describing the effects of air purifying respirator and cook stove changes on cardiopulmonary outcomes remained insufficient. Therefore, air purifiers can serve as efficient IPMs against air pollution. The beneficial effect of air purifiers is likely to have a greater effect in developing countries than in developed countries.

Migration of BPA from Food Packaging and Household Products on the Croatian Market.

BPA is a plasticizer for the production of polycarbonate plastics and epoxy resins and is widely used in the production of household goods, including food packaging. Free BPA is known to migrate from packaging to food, and its uptake has been associated with adverse health effect, particularly the disruption of endocrine activity. The presence and migration of BPA from plastic consumer products are subject to strict regulation in the EU. The aim of this study is to analyse the migration of BPA from different packaging items and household products sold on the Croatian market. To simulate real life exposure, we treated samples with a food simulant. The analytical performance was confirmed with the EU requirements. BPA levels were assessed in 61 samples by HPLC-FLD and the LOQ of the method was 0.005 mg kg-1 for the food simulant. These results showed that the levels of BPA that migrated to the food simulant were below LOQ and in accordance with the specific migration limit into food, which was defined as 0.05 mg kg-1 for all samples. None of the analysed products presented a health hazard. However, these regulations do not refer to products intended for children's use, in which BPA is banned. Furthermore, regulations require testing before putting products on the market, and previous research shows that possible BPA migration occurs due to various uses, along with a cumulative effect of exposure from even very small concentrations. Therefore, for accurate BPA consumer exposure evaluation and possible health risks, a comprehensive approach is needed.

Applicability of an on-line solid-phase extraction liquid chromatography - tandem mass spectrometry for the wastewater-based assessment of human exposure to chemicals from personal care and household products.

Wastewater-based epidemiology (WBE) can be a useful complementary approach to assess human exposure to potentially harmful chemicals, including those from personal care and household products. In this work, a fully automated multiresidue method, based on on-line solid-phase extraction liquid chromatography - tandem mass spectrometry, was developed for the determination of 27 biomarkers of human exposure to selected chemicals from personal care and household products, including parabens, UV filters, phthalates and alternative plasticizers, phosphorous flame retardants/plasticizers (PFRs), and bisphenols. These biomarkers include both the parent compounds and their human metabolites. In addition, two oxidative stress biomarkers, 8-epi-prostaglandin F2α and 4-hydroxy nonenal mercapturic acid, were also considered in the study. The method was carefully optimized to tackle the challenges of analyzing compounds with different physico-chemical properties in a highly complex raw wastewater matrix, while model experiments were performed to investigate filtration losses and analyte stability. The applicability of the developed method was tested by analyzing raw wastewater from four European cities: Antwerp, Brussels (Belgium), Girona (Spain), and Zagreb (Croatia). Twenty-one biomarkers (10 parent compounds and 11 metabolites) were detected in all analyzed wastewater samples. The parent compounds with the highest mass loads were PFRs, parabens, and bisphenol S, while phthalate monoesters were the most prominent metabolites. The mass loads of most compounds were quite similar across cities, but geographic differences were observed for some biomarkers, such as metabolites of phthalates and alternative plasticizers. Exposure was then assessed for seven substances for which quantitative urinary excretion data are known. Our results indicate that safe reference values were exceeded for several contaminants, including butylated phthalates, bisphenol A, and tris(2-butoxyethyl) phosphate, particularly for toddlers. With this relatively simple method, which requires less sample manipulation, it is possible to promptly identify and monitor exposure to harmful chemicals at the population level using the WBE approach.

[Analysis of Flame Retardants Bis(2,3-dibromopropyl) phosphate and Tris(2,3-dibromopropyl) phosphate in Textile Products by GC-MS].

The use of flame retardants, namely bis(2,3-dibromopropyl) phosphate (BDBPP) and tris(2,3-dibromopropyl) phosphate (TDBPP), in textile products such as curtains, carpets and sleeping clothes is banned in Japan under the 'Act on the Control of Household Products Containing Harmful Substances'. Herein, we developed a GC-MS based method to quantify these compounds with greater accuracy and safety than the current official method. For accurate and sensitive quantification, deuterated compounds, BDBPP-d10 and TDBPP-d15, were used as surrogate standards. In consideration of the safety of the analyst, certain solvents and reagents used for the pretreatment that are carcinogenic or have a risk of explosion were replaced. For the extraction step, benzene was replaced by ethyl acetate, and for the methyl derivatization step, the reagent was changed from a self-prepared solution of diazomethane in ether to a solution of trimethylsilyl diazomethane in hexane, a safe and easy-to-use commercially available reagent. The calibration curves were liner in the range of 0.5-8.0 µg/mL for both methylated BDBPP (BDBPP-Me) and TDBPP. The detection limit was 0.05 µg/g for BDBPP-Me and 0.3 µg/g for TDBPP, which is sufficiently low compared to the current detection limits of 10 µg/g for BDBPP-Me and 8 µg/g for TDBPP. The recoveries in various curtain material were 66-108% and relative standard deviations were 1.2-10.2% when 5 µg BDBPP and TDBPP were added to 0.5 g of samples. Thus, the developed method is applicable to textile products of various materials.

Population Attributable Fraction of Gas Stoves and Childhood Asthma in the United States.

Indoor gas stove use for cooking is associated with an increased risk of current asthma among children and is prevalent in 35% of households in the United States (US). The population-level implications of gas cooking are largely unrecognized. We quantified the population attributable fraction (PAF) for gas stove use and current childhood asthma in the US. Effect sizes previously reported by meta-analyses for current asthma (Odds Ratio = 1.34, 95% Confidence Interval (CI) = 1.12−1.57) were utilized in the PAF estimations. The proportion of children (<18 years old) exposed to gas stoves was obtained from the American Housing Survey for the US, and states with available data (n = 9). We found that 12.7% (95% CI = 6.3−19.3%) of current childhood asthma in the US is attributable to gas stove use. The proportion of childhood asthma that could be theoretically prevented if gas stove use was not present (e.g., state-specific PAFs) varied by state (Illinois = 21.1%; California = 20.1%; New York = 18.8%; Massachusetts = 15.4%; Pennsylvania = 13.5%). Our results quantify the US public health burden attributed to gas stove use and childhood asthma. Further research is needed to quantify the burden experienced at the county levels, as well as the impacts of implementing mitigation strategies through intervention studies.

Development and validation of a UPLC-MS/MS method for the quantification of isothiazolinones in the composition and emissions from consumer products.

Isothiazolinones, a family of biocides, are used as preservatives for their fungicidal, bactericidal, and algacidal properties. These compounds can be found in a wide range of consumer and building products, such as paints, varnishes, shampoos, and liquid detergents. A robust analytical UPLC-MS/MS method to identify and quantify seven isothiazolinones (MIT, CMI, BIT, MBIT, BBIT, OIT, and DCOIT) in consumer products and their emissions was developed and validated according to ISO/IEC 17025. The limits of detection (LODs) ranged from 0.14 µg L-1 (BIT) to 0.54 µg L-1 (CMI). The method was applied for the quantification of the seven isothiazolinones in four types of consumer products (i.e., cosmetics, air fresheners, cleaning products, and building products) and the indoor emissions from a paint. Matrix effects were observed for the shampoo (63-74%), the shower gel (67-84%), and the ceramic glass cleaner (53-57%). All isothiazolinones indicated by the manufacturer (i.e., MIT, CMI, BIT, OIT, and DCOIT) were detected in the products and successfully quantified by the UPLC-MS/MS method.

[Examination of Analytical Method for Mothproofing Agents to Revise the Official Methods Based on "Act on the Control of Household Products Containing Harmful Substances"].

In Japan, the use of mothproofing agents [dieldrin and 4,6-dichloro-7-(2,4,5-trichlorophenoxy)-2-trifluoromethylbenzimidazole; DTTB] in textiles is regulated by the Act on the Control of Household Products Containing Harmful Substances. Since official analytical methods for these agents have been in place for approximately 40 years, we developed an improved method in a previous study. In the present study, we validated this method. Accordingly, six laboratories analyzed the sample prepared at 3 µg/g (1/10 of the regulation value) and 30 µg/g (the regulation value). The high accuracy of the results for these samples in almost all the cases (accuracy: 70-120%, repeatability: <10%, reproducibility: <15%), confirmed the validity of the method. In addition, we examined three samples that were distributed before the introduction of the regulation. The analysis results for these samples showed little variation between laboratiories, indicating that our method is also applicable to actual samples. Meanwhile, the quantitative value was clearly lower in one laboratory than in the others. We presumed that the enhanced effect of the sample matrix (matrix effect) on the internal standards in GC-MS analysis was the main cause for this trend. Therefore, we examined the analytical method using polyethylene glycol 300 (PEG) as an analyte protectant. As PEG minimized the GC-MS response difference between the standard solution and the matrix-containing solution, GC-MS analysis with PEG would be useful for matrix effect measurements in this method.

Tracing colophonium in consumer products.

BACKGROUND: Colophonium (rosin) can cause allergic contact dermatitis, mainly due to autoxidation of abietic acid (AbA). Products containing ≥0.1% colophonium should be labeled with EUH208 - "Contains rosin; colophony. May produce an allergic reaction." How should this be measured? OBJECTIVE: To compare the results from different strategies for estimating colophonium levels in consumer products: (a) from AbA, and (b) the sum of all major resin acids. To investigate the ratio of 7-oxodehydroabietic acid (7-O-DeA)/AbA as indication of autoxidation. METHODS: Resin acids were extracted from consumer products, derivatized, and then separated by gas chromatography/mass spectrometry (GC/MS). RESULTS: Resin acids were detected in 9 of 15 products. No product contained colophonium ≥0.1%. Estimation based on AbA resulted in underestimation of the colophonium levels in four of nine products. For three products, the obtained levels from this strategy were only one of two compared to when estimating from the sum of all resin acids. The ratio 7-O-DeA/AbA varied from 74% to 1.4%. CONCLUSIONS: We propose to measure colophonium based on the sum of all detectable major resin acids, including 7-O-DeA. The ratio of 7-O-DeA/AbA should be used as a marker of autoxidation, indicating an increased risk of sensitization. The presented analytical method is simple to use and suitable for further screening studies.

[Examination of Analytical Methods for Methanol, Trichloroethylene, and Tetrachloroethylene to Revise the Official Methods Based on the Act on the Control of Household Products Containing Harmful Substances].

In Japan, the use of methanol, trichloroethylene, and tetrachloroethylene in aerosol household products is banned under the Act on the Control of Household Products Containing Harmful Substances. As the official analytical methods for testing for these substances have not been revised for over 35 years, several issues have been pointed out. Thus, we developed a new method to revise the official method in our previous study. In this study, validation of the proposed method for detecting the target substances was conducted using two aerosol-product samples (A and B), which contained methanol, trichloroethylene, and tetrachloroethylene. Sample A comprised regulated values of these compounds, while sample B comprised one-tenth of the regulated amounts. They also contained several volatile compounds that served as interfering substances. Subsequently, the samples were analyzed using head space/gas chromatography-mass spectrometry, and it was confirmed that the three target substances were separated from the other chemicals on chromatograms. Validation tests were conducted at seven laboratories to evaluate the proposed method using the prepared samples. In one laboratory, the recovery of trichloroethylene and tetrachloroethylene in sample B was slightly higher at 120%, while the recoveries obtained from the other tests were between 70% and 120%. Relative standard deviation at each laboratory was less than 10%. Furthermore, the relative standard deviations between the validation tests with respect to each chemical were less than 15%. Therefore, the method validated in this study was considered to be effective as a revised method for testing for methanol, trichloroethylene, and trichloroethylene in household aerosol products.

Consumers' perceptions of chemical household products and the associated risks.

Accidents with chemical household products are prevalent worldwide and often involve young children. Previous research has shown that consumers use both analytical factors (e.g., warning symbols) and potentially misleading heuristics to evaluate the riskiness. However, it remains unclear whether consumers intuitively think of the specific risks of these products when handling them. We conducted an online survey with Swiss consumers (N = 1109) aiming to investigate consumer's spontaneous and prompted risk perception of chemical household products. First, we asked them about their free associations to laundry detergent, descaler, mold remover and essential oils. While participants were aware of the risks when prompted about them, they did not name them intuitively, but mainly thought of the possible uses and attributes of the product. Next, we examined prerequisites to safe handling of chemical household products. This included applied knowledge about the products, but also factors like perceived barriers to safe use. Finally, we assessed the predictors of perceived severity of accidents in order to estimate the potential behavioral changes that these predictors might elicit. For interventions, particular attention should be accorded to personal risk awareness and the perception of potential barriers, which were significantly related to the perceived severity of accidents.

Environmental risk assessment of polycarboxylate polymers used in cleaning products in the United States.

Polycarboxylate polymers have been common components of consumer and institutional cleaning products for decades. With interest heightened in the potential environmental impact of polymers, the American Cleaning Institute, the industry trade association of the cleaning products industry in the United States, is reassessing the state of the science regarding the environmental safety of polymers in cleaning products. In this case study, acrylic acid homopolymers and acrylic acid-maleic acid copolymers are evaluated using historical ecotoxicity data that have been reported over the past three decades. The evaluation includes an environmental exposure assessment that is based on recent information regarding the occurrence of those ingredients in cleaning products and market sales data for cleaning products sold in the United States. The ecotoxicity of polycarboxylate polymers is generally low. Consequently, the potential environmental risks associated with their use in cleaning products in the United States are low even when applying very conservative assumptions to the environmental exposure assessment. In addition, there are recent supporting conclusions from assessments by the governments of Australia and Canada that polycarboxylate polymers are polymers of low concern, and the U.S. Environmental Protection Agency has included a number of polycarboxylate polymers among the ingredients on its Safer Chemical Ingredients List based on their low hazard profile.

A novel method for purification, quantitative analysis and characterization of microplastic fibers using Micro-FTIR.

Microplastics pose a worldwide risk for the environment. Microplastic fibers, which are released during the household washing of synthetic fabrics, are a substantial percentage of microplastics in rivers and in oceans. A novel quantification and simultaneous identification of fiber polymers via Micro-FTIR (Fourier Transform Infrared Spectroscopy) was developed. Washing simulations with commercially available household products were performed and effluents were filtered either on GF/F filters (0.7 µm) or on Anodisc filter (0.2 µm), to gather even the smallest fibers. Furthermore, a novel purification procedure of effluents was developed. Subsequently, filters were analyzed also with the scanning electronic microscope (SEM) to confirm the width and length of fibers. This novel method is robust and replicable and it allows better quantification of fibers released and identification of fiber polymers with optimal matches (averagely 80%).

Measured concentrations of consumer product chemicals in California house dust: Implications for sources, exposure, and toxicity potential.

Household dust is a reservoir of various consumer product chemicals. Thus, characterizing comprehensive chemical profiles of house dust may help improve our understanding of residential chemical exposure. We have previously developed a method for detecting a broad spectrum of chemicals in dust by applying a combination of target, suspect screening, and non-target methods with mass spectrometry preceded by liquid chromatography and gas chromatography. Building upon a previous study that detected 271 compounds in 38 dust samples, we presented concentrations of 144 compounds that were confirmed and quantified by standards in the same set of samples. Ten compounds were measured with median concentrations greater than 10 000 ng/g of dust: cis-hexadec-6-enoic acid, squalene, cholesterol, vitamin E, bis(2-ethylhexyl) phthalate, dioctyl terephthalate, linoleic acid, tricaprylin, tris(1-chloroisopropyl) phosphate, and oxybenzone. We also reviewed in vitro toxicity screening data to identify compounds that were not previously detected in indoor dust but have potential for adverse health effects. Among 119 newly detected compounds, 13 had endocrine-disrupting potential and 7 had neurotoxic potential. Toxicity screening data were not available for eight biocides, which may adversely affect health. Our results strive to provide more comprehensive chemical profiles of house dust and identified information gaps for future health studies.

Isothiazolinones in cleaning products: Analysis with liquid chromatography tandem mass spectrometry of samples from sensitized patients and market.

BACKGROUND: Methylchloroisothiazolinone (MCI) and methylisothiazolinone (MI) contact dermatitis is a severe problem. The high concentrations of these substances and other isothiazolinones such as benzisothiazolinone (BIT) and octylisothiazolinone (OIT) contained in cleaning products may cause allergic contact dermatitis in sensitized patients. OBJECTIVES: To evaluate the exposure to isothiazolinones contained in cleaning products on the market and from sensitized patients, and to verify the accuracy of labeling. METHODS: A total of 34 cleaning products were collected (17 supplied by sensitized patients and 17 bought randomly). Analysis was made of the concentrations of MI, MCI, BIT, and OIT using liquid chromatography tandem mass spectrometry (LC-MS/MS). RESULTS: MI and BIT were the components most frequently detected. Of all the products analyzed, 76.5% contained at least one isothiazolinone. Twelve products had an MI concentration above the permitted level for rinse-off cosmetics. Most of them were coming into direct contact with the skin in daily use. Mislabeling occurred in eight products. CONCLUSIONS: Some cleaning products with high concentrations of isothiazolinones may cause cutaneous symptoms in sensitized patients, especially in spray form. The labeling should be correct, also regarding the use of each article.

Home chemical and microbial transitions across urbanization.

Urbanization represents a profound shift in human behaviour, and has considerable cultural and health-associated consequences1,2. Here, we investigate chemical and microbial characteristics of houses and their human occupants across an urbanization gradient in the Amazon rainforest, from a remote Peruvian Amerindian village to the Brazilian city of Manaus. Urbanization was found to be associated with reduced microbial outdoor exposure, increased contact with housing materials, antimicrobials and cleaning products, and increased exposure to chemical diversity. The degree of urbanization correlated with changes in the composition of house bacterial and microeukaryotic communities, increased house and skin fungal diversity, and an increase in the relative abundance of human skin-associated fungi and bacteria in houses. Overall, our results indicate that urbanization has large-scale effects on chemical and microbial exposures and on the human microbiota.

Qualitative Analysis of Air Freshener Spray.

Air fresheners contain various chemicals that may or may not be harmful to human health and the environment. These products are widely used in different settings such as homes, schools, offices, and hospitals with ignorance of their real ingredients and their relative health effects. Thus, this preliminary study was carried out to identify the presence of different compounds in spray air fresheners that were not disclosed on the product's label. Four different brands of spray air fresheners were selected randomly from a local store, in which two were of mid-to-high cost and the remaining two of low cost. The samples were analyzed using gas chromatography/mass spectrometry headspace, in which single components of the samples were identified by the mass spectrometry detector. The results were shown as a chromatogram of several peaks, each representing different compounds. The chemicals found in the samples include; lilial, galaxolide, benzenemethanol, musk ketone, butylated hydroxytoluene, and linalool. These chemicals may cause irritation and other health problems. However, none of them were revealed on the product's label. The study concludes that air fresheners need to be free of any toxic or harmful chemicals and include natural ingredients instead.

Automated online solid-phase extraction liquid chromatography tandem mass spectrometry investigation for simultaneous quantification of per- and polyfluoroalkyl substances, pharmaceuticals and personal care products, and organophosphorus flame retardants in environmental waters.

This work describes development of a quick and accurate online solid-phase extraction (SPE) liquid chromatography tandem mass spectrometry method for simultaneous determination of 87 emerging organic compounds, including 22 per- and polyfluoroalkyl substances, 58 pharmaceuticals and personal care products, and 7 organophosphorus flame retardants, in diverse water matrices. Considering the wide range of physicochemical properties for the target contaminants, efficient analysis in one injection is challenging. Thus, key extraction and analytical parameters, including online SPE sorbent, mobile phase additives, sample pH, loading solvent pH and composition, injection volume, and valve-switching time, were systematically optimized. The final conditions, namely a polymeric reversed-phase column with alkaline samples and an acidic loading solvent, provided satisfactory results for all target analytes compared to conventional methods that employ acidic samples for multi-residue analysis. The method detection limits (MDLs) ranged from 0.16 to 5.13 ng L-1 with 85% of MDLs lower than 2 ng L-1 for sample volumes of just 1.8 mL. The method also demonstrated satisfactory accuracy with 82% of analytes exhibiting 70-130% recovery. Importantly, only 30 min was required per sample. The optimized method was successfully applied to investigate the removal efficiency of emerging contaminants in a drinking water treatment plant and to analyze the environmental occurrence of target analytes. The method is sensitive, reliable, labor-saving, and cost effective, and therefore has the potential to advance large-scale environmental monitoring programs.

Processing of household waste in the BTLSS using the wet combustion method.

The present study discusses physicochemical methods of organic waste processing in closed biotechnical life support systems (BTLSS). Sanitary and household cotton wastes were processed by the method of wet combustion in hydrogen peroxide using an alternating current electric field - a promising physicochemical method for organic waste processing in the BTLSS. The highest efficiency of the process (in terms of power consumption, duration of the process, and oxidation rate) was achieved in experiments with oxidation of a combination of cotton fabrics and urea-containing wastes such as human urine and feces. The reason for this must be that urea is a reactive aqueous solvent of cellulose.