ABSTRACT
2D materials, given their form-factor, high surface-to-volume ratio, and chemical functionality have immense use in sensor design. Engineering 2D heterostructures can result in robust combinations of desirable properties but sensor design methodologies require careful considerations about material properties and orientation to maximize sensor response. This study introduces a sensor approach that combines the excellent electrical transport and transduction properties of graphite film with chemical reactivity derived from the edge sites of semiconducting molybdenum disulfide (MoS2) through a two-step chemical vapour deposition method. The resulting vertical heterostructure shows potential for high-performance hybrid chemiresistors for gas sensing. This architecture offers active sensing edge sites across the MoS2 flakes. We detail the growth of vertically oriented MoS2 over a nanoscale graphite film (NGF) cross-section, enhancing the adsorption of analytes such as NO2, NH3, and water vapor. Raman spectroscopy, density functional theory calculations and scanning probe methods elucidate the influence of chemical doping by distinguishing the role of MoS2 edge sites relative to the basal plane. High-resolution imaging techniques confirm the controlled growth of highly crystalline hybrid structures. The MoS2/NGF hybrid structure exhibits exceptional chemiresistive responses at both room and elevated temperatures compared to bare graphitic layers. Quantitative analysis reveals that the sensitivity of this hybrid sensor surpasses other 2D material hybrids, particularly in parts per billion concentrations.
ABSTRACT
The impact of micro and nanoplastic debris on our aquatic ecosystem is among the most prominent environmental challenges we face today. In addition, nanoplastics create significant concern for environmentalists because of their toxicity and difficulty in separation and removal. Here we report the development of a 3D printed moving bed water filter (M-3DPWF), which can perform as an efficient nanoplastic scavenger. The enhanced separation of the nanoplastics happens due to the creation of a charged filter material that traps the more surface charged nanoparticles selectively. Synthetic contaminated water from polycarbonate waste has been tested with the filter, and enhanced nanoplastic removal has been achieved. The proposed filtration mechanism of surface-charge based water cleaning is further validated using density function theory (semi-empirical) based simulation. The filter has also shown good structural and mechanical stability in both static and dynamic water conditions. The field suitability of the novel treatment system has also been confirmed using water from various sources, such as sea, river, and pond. Our results suggest that the newly developed water filter can be used for the removal of floating nanoparticles in water as a robust advanced treatment system.
ABSTRACT
Anisotropy in a crystal structure can lead to large orientation-dependent variations of mechanical, optical, and electronic properties. Material orientation control can thus provide a handle to manipulate properties. Here, a novel sputtering approach for 2D materials enables growth of ultrathin (2.5-10 nm) tellurium films with rational control of the crystalline orientation templated by the substrate. The anisotropic Te ã0001ã helical chains align in the plane of the substrate on highly oriented pyrolytic graphite (HOPG) and orthogonally to MgO(100) substrates, as shown by polarized Raman spectroscopy and high-resolution electron microscopy. Furthermore, the films are shown to grow in a textured fashion on HOPG, in contrast with previous reports. These ultrathin Te films cover exceptionally large areas (>1 cm2) and are grown at low temperature (25 °C) affording the ability to accommodate a variety of substrates including flexible electronics. They are robust toward oxidation over a period of days and exhibit the non-centrosymmetric P3121 Te structure. Raman signals are acutely dependent on film thickness, suggesting that optical anisotropy persists and is even enhanced at the ultrathin limit. Hall effect measurements indicate orientation-dependent carrier mobility up to 19 cm2 V-1 s-1. These large-area, ultrathin Te films grown by a truly scalable, physical vapor deposition technique with rational control of orientation/thickness open avenues for controlled orientation-dependent properties in semiconducting thin films for applications in electronic and optoelectronic devices.
ABSTRACT
A liquid dielectric based on a core-shell architecture having a superparamagnetic iron oxide core and a shell of silicon dioxide was synthesized. The frequency dependence of dielectric properties was evaluated for different concentrations of iron oxide. The dependence of magnetic field on the dielectric properties was also studied. Aqueous ferrofluid exhibited a giant dielectric constant of 6.4 × 105 at 0.1 MHz at a concentration of 0.2 vol% and the loss tangent was 3. The large rise in dielectric constant at room temperature is modelled and explained using percolation theory and Maxwell-Wagner-Sillars type polarization. The ferrofluid is presumed to consist of nanocapacitor networks which are wired in series along the lateral direction and parallel along longitudinal direction. On the application of an external magnetic field, the chain formation and its alignment results in the variation of dielectric permittivity.
ABSTRACT
Ab initio density functional theory simulations were used to calculate the electronic structure and the total energy of double-walled carbon nanotubes (DWCNTs). The relaxed configurations studied were uncapped, infinitely-long zigzag@zigzag double-walled carbon nanotubes. The lowest energy configuration was found to correspond to an interwall distance of 0.35 nm, except for the configurations with inner tube chiral indices (5,0), (6,0) and (7,0). The largest binding energies were found to correspond to a 0.35 nm interwall distance for all the DWCNT configurations studied, and increasing with DWCNT average diameter. In terms of the effect of the interwall interaction on the electronic band gap of DWCNTs, four regions of band gap were obtained which were termed: zero band gap, narrow band gap, small band gap, and medium band gap regions. These regions offer the possibility to first tune the electronic band gap to a region with a desired range, and further tune that choice within the region itself by varying the interwall distance. It was also found that zigzag@zigzag DWCNTs with outer tube leading chiral index n = 3k + 1 or n = 3k + 2 (k being an integer) follow, as a general trend, an inversely proportional relation of the electronic band gap with respect to the average diameter.
ABSTRACT
In the evaluation of compatibility of different components of cell for high-energy and extreme-conditions applications, the highly focused are positive and negative electrodes and their interaction with electrolyte. However, for high-temperature application, the other components are also of significant influence and contribute toward the total health of battery. In present study, we have investigated the behavior of aluminum, the most common current collector for positive electrode materials for its electrochemical and temperature stability. For electrochemical stability, different electrolytes, organic and room temperature ionic liquids with varying Li salts (LiTFSI, LiFSI), are investigated. The combination of electrochemical and spectroscopic investigations reflects the varying mechanism of passivation at room and high temperature, as different compositions of decomposed complexes are found at the surface of metals.
ABSTRACT
On-chip energy storage and management will have transformative impacts in developing advanced electronic platforms with built-in energy needs for operation of integrated circuits driving a microprocessor. Though success in growing stand-alone energy storage elements such as electrochemical capacitors (super and pseusocapacitors) on a variety of substrates is a promising step towards this direction. In this work, on-chip energy storage is demonstrated using architectures of highly aligned vertical carbon nanotubes (CNTs) acting as supercapacitors, capable of providing large device capacitances. The efficiency of these structures is further increased by incorporating electrochemically active nanoparticles such as MnOx to form pseudocapacitive architectures thus enhancing device capacitance areal specific capacitance of 37 mF/cm2. The demonstrated on-chip integration is up and down-scalable, compatible with standard CMOS processes, and offers lightweight energy storage what is vital for portable and autonomous device operation with numerous advantages as compared to electronics built from discrete components.
ABSTRACT
Owing to their great significance for energy storage and sensing applications, multi-layer papers consisting of graphene oxide-carbon nanotube (GO-CNT) hybrid sheets were prepared by in situ exfoliation of graphite oxide in the presence of oxidized CNTs (oCNTs). For the first time we elucidate the influence of oCNTs on chemisorbed water (CW), i.e. the water molecules inherently bound to the oxygen functional groups (OFGs) of graphene oxide (GO) and responsible for irreversible structural damage upon thermal reduction processes. We show that oCNTs self-assemble onto GO sheets during the liquid phase processing steps by forming cooperatively strengthened OH···O[double bond, length as m-dash]C hydrogen bonds between the carboxylic groups of the oCNTs and OFGs of GO. At oCNT amounts of about 10 to 15 wt% this leads to the displacement of considerable amounts of CW without altering the original chemical composition of GO. The thermally reduced GO-CNT (rGO-CNT) papers reveal improved sp2 character and an enhancement of the specific capacitance by 75% with respect to thermally reduced GO (rGO), largely due to the effective removal of CW by oxidized CNTs. These findings disclose the relevance of the cooperative hydrogen bonding phenomena in graphene oxide paper/film electrodes for the development of improved electrochemical energy storage and sensing devices.
ABSTRACT
The high field phenomena of inter-valley transfer and avalanching breakdown have long been exploited in devices based on conventional semiconductors. In this Article, we demonstrate the manifestation of these effects in atomically-thin WS2 field-effect transistors. The negative differential conductance exhibits all of the features familiar from discussions of this phenomenon in bulk semiconductors, including hysteresis in the transistor characteristics and increased noise that is indicative of travelling high-field domains. It is also found to be sensitive to thermal annealing, a result that we attribute to the influence of strain on the energy separation of the different valleys involved in hot-electron transfer. This idea is supported by the results of ensemble Monte Carlo simulations, which highlight the sensitivity of the negative differential conductance to the equilibrium populations of the different valleys. At high drain currents (>10 µA/µm) avalanching breakdown is also observed, and is attributed to trap-assisted inverse Auger scattering. This mechanism is not normally relevant in conventional semiconductors, but is possible in WS2 due to the narrow width of its energy bands. The various results presented here suggest that WS2 exhibits strong potential for use in hot-electron devices, including compact high-frequency sources and photonic detectors.
ABSTRACT
Reduced graphene oxide (rGO) has recently emerged as a very promising family of exotic carbon material with augmented performance in electronic and optoelectronic devices. Herein, we report an efficient and novel inorganic electroluminescent device geometry, where a new phosphor composite, reduced graphene oxide wrapped ZnS:Cu,Al, acts as an active emitting layer and an exfoliated hexagonal boron nitride (h-BN) as a dielectric layer. The roles of rGO in the active layer as a conductive support and local electric field enhancing agent are attributed to its wrinkles being unraveled compared with other carbon exotic nano-forms such as carbon nanotubes, graphite, charcoal and activated carbon, which significantly improves the brightness of the device (â¼50 cd m-2 for 0.50 wt% rGO/ZnS:Cu,Al at 10 kHz and 110 V with an external quantum efficiency of â¼6.3% ± 0.1% and current efficiency of â¼0.81 ± 0.09 cd A-1). This new and facile strategy to construct the luminescent devices could be a paradigm shift towards cost effective, highly stable in air (for several days) and energy efficient next generation display devices.
ABSTRACT
Understanding and controlling charge and energy flow in state-of-the-art semiconductor quantum wells has enabled high-efficiency optoelectronic devices. Two-dimensional (2D) Ruddlesden-Popper perovskites are solution-processed quantum wells wherein the band gap can be tuned by varying the perovskite-layer thickness, which modulates the effective electron-hole confinement. We report that, counterintuitive to classical quantum-confined systems where photogenerated electrons and holes are strongly bound by Coulomb interactions or excitons, the photophysics of thin films made of Ruddlesden-Popper perovskites with a thickness exceeding two perovskite-crystal units (>1.3 nanometers) is dominated by lower-energy states associated with the local intrinsic electronic structure of the edges of the perovskite layers. These states provide a direct pathway for dissociating excitons into longer-lived free carriers that substantially improve the performance of optoelectronic devices.
ABSTRACT
We demonstrate a novel form of thermally-assisted hysteresis in the transfer curves of monolayer MoS2 FETs, characterized by the appearance of a large gate-voltage window and distinct current levels that differ by a factor of â¼102. The hysteresis emerges for temperatures in excess of 400 K and, from studies in which the gate-voltage sweep parameters are varied, appears to be related to charge injection into the SiO2 gate dielectric. The thermally-assisted memory is strongly suppressed in equivalent measurements performed on bilayer transistors, suggesting that weak screening in the monolayer system plays a vital role in generating its strongly sensitive response to the charge-injection process. By exploiting the full features of the hysteretic transfer curves, programmable memory operation is demonstrated. The essential principles demonstrated here point the way to a new class of thermally assisted memories based on atomically thin two-dimensional semiconductors.
ABSTRACT
Energy storage devices that provide high specific power without compromising on specific energy are highly desirable for many electric-powered applications. Here, we demonstrate that polymer organic radical gel materials support fast bulk-redox charge storage, commensurate to surface double layer ion exchange at carbon electrodes. When integrated with a carbon-based electrical double layer capacitor, nearly ideal electrode properties such as high electrical and ionic conductivity, fast bulk redox and surface charge storage as well as excellent cycling stability are attained. Such hybrid carbon redox-polymer-gel electrodes support unprecedented discharge rate of 1,000C with 50% of the nominal capacity delivered in less than 2 seconds. Devices made with such electrodes hold the potential for battery-scale energy storage while attaining supercapacitor-like power performances.
ABSTRACT
Collagenous wastes discarded from leather industry were stabilized using superparamagnetic iron oxide nanoparticles and further converted into a magnetic nanocarbon. Stabilization of collagen using iron oxide nanoparticles treatment (25% offer) was confirmed through differential scanning calorimetric analysis and further evidenced through scanning electron microscopic analysis. A simple high temperature treatment of the collagen-iron oxide nanoparticle composite at 850 degrees C for 2 h under Ar atmosphere yielded a bi-functional, magnetic and conducting, nanocarbon. The X-ray diffraction and Raman spectroscopic analysis reveal the partial graphitation and X-ray photoelectron spectroscopic results show the presence of trace-iron containing carbon, naturally doped with nitrogen and oxygen. Transmission electron microscopic analysis show the presence of larger iron oxide nanocrystals embedded in graphitic carbon layers while superconducting quantum interference device based analysis reveals a perfect ferrimagnetic property with saturation magnetization. Thus, we have stabilized the collagen waste fibers using iron oxide nanoparticles and converted them into a bi-functional nanocarbon, which has potential for various applications including energy, leather making and environmental remediation.
Subject(s)
Carbon/chemistry , Collagen/chemistry , Magnetite Nanoparticles/chemistry , Nanocomposites/chemistry , Hot Temperature , Microscopy, Electron, Transmission , X-Ray DiffractionABSTRACT
Graphene quantum dots (GQDs) are a promising category of materials with remarkable size dependent properties like tunable bandgap and photoluminescence along with the possibility of effective chemical functionalization. Doping of GQDs with heteroatoms is an interesting way of regulating their properties. Herein, we report a facile and scalable one-step synthesis of luminescent GQDs, substitutionally co-doped with N, F and S, of â¼2 nm average size by a microwave treatment of multi-walled carbon nanotubes in a customized ionic liquid medium. The use of an ionic liquid coupled with the use of a microwave technique enables not only an ultrafast process for the synthesis of co-doped GQDs, but also provides excellent photoluminescence quantum yield (70%), perhaps due to the interaction of defect clusters and dopants.
ABSTRACT
We fabricate transistors from chemical vapor deposition-grown monolayer MoS2 crystals and demonstrate excellent current saturation at large drain voltages (Vd). The low-field characteristics of these devices indicate that the electron mobility is likely limited by scattering from charged impurities. The current-voltage characteristics exhibit variable range hopping at low Vd and evidence of velocity saturation at higher Vd. This work confirms the excellent potential of MoS2 as a possible channel-replacement material and highlights the role of multiple transport phenomena in governing its transistor action.
Subject(s)
Disulfides/chemistry , Molybdenum/chemistry , Transistors, Electronic , Crystallization , Electric Conductivity , Equipment Design , Models, MolecularABSTRACT
We report the design and synthesis of a polymer structure from a cross-linkable epoxy-ionic liquid system which behaves like a hard and brittle epoxy thermoset, perfectly ductile thermoplastic and an elastomer, all depending on controllable network compositions.
ABSTRACT
Through this study, the results of density functional theory calculations within the local density approximation of the electronic structure of zigzag-zigzag double-walled carbon nanotubes (DWCNTs), with chiral indices (n, 0)@(m, 0) for n = 7-15, and m = 15-26, has been presented and the effects of interwall interaction and orbital hybridization on the electronic structure of these systems has been discussed. It was observed that the electronic band gap of the aforementioned DWCNTs depends on the interwall distance only for metallic-semiconductor configurations and on the intrinsic properties of the constituent tubes in all other combinations. It was also observed that the calculated band gap for most of the metallic-metallic DWCNTs was smaller than semiconductor-metallic, metallic-semiconductor, and semiconductor-semiconductor configurations. Metallic-semiconductor DWCNTs were found to be desirable for band gap tuning applications because of their dependence on interwall distance, opening up the possibility of using such systems in electronic device applications, such as transistors. Other applications include the use of DWCNTs in macroscopic carbon nanotube conducting wires, for which metallic-metallic and semiconducting-metallic zigzag-zigzag DWCNTs were found to be the most desirable configurations due to their small band gaps.
Subject(s)
Nanotubes, Carbon/chemistry , Semiconductors , Nanotechnology , Particle SizeABSTRACT
Here, we present a temperature (T) dependent comparison between field-effect and Hall mobilities in field-effect transistors based on few-layered WSe2 exfoliated onto SiO2. Without dielectric engineering and beyond a T-dependent threshold gate-voltage, we observe maximum hole mobilities approaching 350â cm(2)/Vs at T = 300â K. The hole Hall mobility reaches a maximum value of 650â cm(2)/Vs as T is lowered below ~150â K, indicating that insofar WSe2-based field-effect transistors (FETs) display the largest Hall mobilities among the transition metal dichalcogenides. The gate capacitance, as extracted from the Hall-effect, reveals the presence of spurious charges in the channel, while the two-terminal sheet resistivity displays two-dimensional variable-range hopping behavior, indicating carrier localization induced by disorder at the interface between WSe2 and SiO2. We argue that improvements in the fabrication protocols as, for example, the use of a substrate free of dangling bonds are likely to produce WSe2-based FETs displaying higher room temperature mobilities, i.e. approaching those of p-doped Si, which would make it a suitable candidate for high performance opto-electronics.
ABSTRACT
Being an atomically thin material, graphene is known to be extremely susceptible to its environment, including defects and phonons in the substrate on which it is placed as well as gas molecules that surround it. Thus, any device design using graphene has to take into consideration all surrounding components, and device performance needs to be evaluated in terms of environmental influence. However, no methods have been established to date to readily measure the density and distribution of external perturbations in a quantitative and non-destructive manner. Here, we present a rapid and non-contact method for visualizing the distribution of molecular adsorbates on graphene semi-quantitatively using terahertz time-domain spectroscopy and imaging. We found that the waveform of terahertz bursts emitted from graphene-coated InP sensitively changes with the type of atmospheric gas, laser irradiation time, and ultraviolet light illumination. The terahertz waveform change is explained through band structure modifications in the InP surface depletion layer due to the presence of localized electric dipoles induced by adsorbed oxygen. These results demonstrate that terahertz emission serves as a local probe for monitoring adsorption and desorption processes on graphene films and devices, suggesting a novel two-dimensional sensor for detecting local chemical reactions.