ABSTRACT
BACKGROUND: Diesel exhaust is carcinogenic and exposure to diesel particles cause health effects. We investigated the toxicity of diesel exhaust particles designed to have varying physicochemical properties in order to attribute health effects to specific particle characteristics. Particles from three fuel types were compared at 13% engine intake O2 concentration: MK1 ultra low sulfur diesel (DEP13) and the two renewable diesel fuels hydrotreated vegetable oil (HVO13) and rapeseed methyl ester (RME13). Additionally, diesel particles from MK1 ultra low sulfur diesel were generated at 9.7% (DEP9.7) and 17% (DEP17) intake O2 concentration. We evaluated physicochemical properties and histopathological, inflammatory and genotoxic responses on day 1, 28, and 90 after single intratracheal instillation in mice compared to reference diesel particles and carbon black. RESULTS: Moderate variations were seen in physical properties for the five particles: primary particle diameter: 15-22 nm, specific surface area: 152-222 m2/g, and count median mobility diameter: 55-103 nm. Larger differences were found in chemical composition: organic carbon/total carbon ratio (0.12-0.60), polycyclic aromatic hydrocarbon content (1-27 µg/mg) and acid-extractable metal content (0.9-16 µg/mg). Intratracheal exposure to all five particles induced similar toxicological responses, with different potency. Lung particle retention was observed in DEP13 and HVO13 exposed mice on day 28 post-exposure, with less retention for the other fuel types. RME exposure induced limited response whereas the remaining particles induced dose-dependent inflammation and acute phase response on day 1. DEP13 induced acute phase response on day 28 and inflammation on day 90. DNA strand break levels were not increased as compared to vehicle, but were increased in lung and liver compared to blank filter extraction control. Neutrophil influx on day 1 correlated best with estimated deposited surface area, but also with elemental carbon, organic carbon and PAHs. DNA strand break levels in lung on day 28 and in liver on day 90 correlated with acellular particle-induced ROS. CONCLUSIONS: We studied diesel exhaust particles designed to differ in physicochemical properties. Our study highlights specific surface area, elemental carbon content, PAHs and ROS-generating potential as physicochemical predictors of diesel particle toxicity.
Subject(s)
Gasoline/toxicity , Particulate Matter/toxicity , Polycyclic Aromatic Hydrocarbons/toxicity , Vehicle Emissions/toxicity , Animals , Carbon , Carcinogens , DNA Damage , Lung , Mice , Mice, Inbred C57BLABSTRACT
In present study, engine exhaust was sampled for measurement and analysis of unregulated emissions from a four cylinder transportation diesel engine using a state-of-the-art FTIR (Fourier transform infrared spectroscopy) emission analyzer. Test fuels used were Karanja biodiesel blend (B20) and baseline mineral diesel. Real-time emission measurements were performed for raw exhaust as well as exhaust sampled downstream of the two in-house prepared non-noble metal based diesel oxidation catalysts (DOCs) and a baseline commercial DOC based on noble metals. Two prepared non-noble metal based DOCs were based on Co-Ce mixed oxide and Lanthanum based perovskite catalysts. Perovskite based DOC performed superior compared to Co-Ce mixed oxide catalyst based DOC. Commercial noble metal based DOC was found to be the most effective in reducing unregulated hydrocarbon emissions in the engine exhaust, followed by the two in-house prepared non-noble metal based DOCs.
ABSTRACT
Two new formulations of non-noble metal based diesel oxidation catalysts based on CoCe based mixed oxide (DOC2) and perovskite catalysts (DOC3) were prepared and retrofitted in a 4-cylinder diesel engine fueled by diesel and Karanja biodiesel blend (KB20). In this study, their effectiveness in reducing raw exhaust particulate emissions vis-à-vis a commercial diesel oxidation catalyst (DOC1) was evaluated. Emission characteristics such as particle number-size distribution, mass-size distribution, and surface area-size distribution, total particle number concentration and count mean diameter as a function of engine load at constant engine speed were evaluated. Variations in total particle number concentration as a function of engine speed were also determined. The prepared DOCs and the commercial DOC showed varying degrees of performance as a function of engine operating conditions. Overall, effectiveness of the prepared DOC's appeared to be more fuel specific. For diesel exhaust, overall performance of DOC1 was more effective compared to both prepared DOCs, with DOC2 being superior to DOC3. In case of KB20 exhaust, the overall performance of DOC2 was either more effective or nearly comparable to DOC1, while DOC3 being not so effective. This showed that the DOCs based on CoCe based mixed oxide catalysts have potential to replace commercial noble metal based DOC's, especially in engines fueled by biodiesel.
ABSTRACT
Toxicity of engine out emissions from primary and secondary aerosols has been a major cause of concern for human health and environmental impact. This study aims to evaluate comparative toxicity of nanoparticles emitted from a modern common rail direct injection engine (CRDI) fuelled with biodiesel blend (B20) vis-à-vis mineral diesel. The toxicity and potential health hazards of exhaust particles were assessed using various parameters such as nanoparticle size and number distribution, surface area distribution, elemental and organic carbon content and polycyclic aromatic hydrocarbons adsorbed onto the particle surfaces, followed by toxic equivalent factor assessment. It was found that biodiesel particulate toxicity was considerably lower in comparison to mineral diesel.