Awareness, Safety Practices and Associated Factors Among E-Waste Recycling Workers in Bangladesh.

Awareness of electronic waste (e-waste) improves safety practices among workers, thereby reducing health risks associated with pollutants. Investigating the awareness and safe practices among these workers could help identify areas for improvement, a task not yet undertaken in Bangladesh. Consequently, this study aimed to examine the awareness, safety measures, and associated factors among e-waste workers in the country. In this cross-sectional study, 236 workers from an e-waste recycling facility located near Dhaka were interviewed using a semi-structured questionnaire from August to September 2022. Eight questions captured information on socio-demographics and work factors, 24 questions on e-waste awareness, and 11 questions on safety practices. Total awareness and safety scores were calculated and categorized as "good" and "poor" based on a cut-off point of 80% of the total score. Bivariate and regression analyses were done to determine associated factors. Only 25% of workers had good e-waste awareness; major knowledge gaps were regarding minimization, health hazards, and environmental impact. Good awareness was significantly associated with female gender, higher education, income, smoking, experience ⩾5 years, and training. About 58% followed good safety practices, but the use of boots and helmets was inadequate. Good safety practices were significantly associated with higher education, income, smoking, experience, training, and overtime work. On multivariable analysis, those with higher education had 12 times (95% CI 4.83-32.81) and 6 times (95% CI 2.94-12.81) higher odds of good awareness and practices, respectively. Trained workers had 3.6 times (95% CI 1.67-7.52) higher odds of good practices. There was a significant correlation between awareness and practices (r = .70, P < .001). The study found poor awareness and inadequate safety practices related to e-waste among the workers. Urgent interventions like training, the use of protective gear, and stringent policies are warranted to increase awareness and safety behaviors.

This study looked at how aware e-waste recycling workers in Bangladesh are about the hazards of e-waste and whether they take proper safety measures during their work. E-waste, which refers to discarded electronic devices and components, contains hazardous materials like heavy metals and toxic chemicals. If not handled properly, these can cause health problems for the workers as well as environmental pollution. The researchers interviewed 236 e-waste workers in Dhaka in 2022. They asked questions to assess the workers' knowledge about e-waste and its risks, as well as what safety gear and practices they used at work. The study found that only 25% of the workers had good awareness about e-waste hazards. Major gaps were around minimizing e-waste, the health risks, and environmental impact. Around 58% reported following good safety practices like using masks and gloves. However, many did not use critical protective gear like safety boots and helmets consistently. Higher education levels and professional training were linked to better awareness and safer practices. Trained workers were more likely to follow good safety practices. The study findings suggest that urgent interventions like health education and training programs are needed. This can help increase awareness and ensure workers take adequate precautions to reduce health risks from mishandling e-waste in Bangladesh.

A raising alarm on the current global electronic waste situation through bibliometric analysis, life cycle, and techno-economic assessment: a review.

Electronic waste (E-waste) production worldwide is increasing three times faster than the growth of the global population, and it is predicted that the total volume of E-waste will reach 74 million tonnes by 2030. United Nations warned that unless emissions of heat-trapping gases are drastically reduced, humanity will face catastrophic climate change. We created a bibliometric analysis and discussed the life cycle and techno-economic assessments of the current E-waste situation. We found trending E-waste topics, particularly those related to industrial facilities implementing a circular economy framework and improving the recycling methods of lithium-ion batteries, and this was linked to the topic of electric vehicles. Other research themes included bioleaching, hydrometallurgy, reverse logistics, heavy metal life cycle assessment, and sustainability. These topics can interest industrial factories and scientists interested in these fields. Also, throughout techno-economic assessments, we highlighted several economic and investment opportunities to benefit stakeholders from E-waste recycling. While the rate of E-waste is increasing, consumer education on the proper E-waste management strategies, a collaboration between international organizations with the industrial sector, and legislation of robust E-waste regulations may reduce the harmful effect on humans and the environment and increase the income to flourish national economies.

Inventory and management of E-waste: a case study of Kerala, India.

The recent surge in electronic device usage has led to a notable rise in electronic waste (E-waste) generation, presenting significant environmental challenges. This study aims to quantify Kerala's E-waste inventory and formulate a comprehensive management plan. Utilizing sales data from 2017 to 2020 and estimating E-waste generation based on "average" or "end-of-life" durations of electrical and electronic equipment (EEE) items, the analysis forecasts substantial E-waste quantities. Key assumptions include correlating sales data with E-waste generation and utilizing guidelines for estimating E-waste quantities based on EEE item types and sales figures. The highest E-waste generation is predicted for the years 2028-2029, estimated at 97,541 tonnes, which is crucial for the state's management strategy. To address this challenge, the study proposes a comprehensive environmental management plan that integrates the principles of reduce, reuse, and recycle (3R) into its core strategies. The plan includes establishing 78 collection units across the state, strategically allocated based on the Taluk (a sub-division of a district) population, to ensure efficient E-waste collection and recovery of reusable items. Additionally, the study outlines the need for 273 recycling units statewide, with Malappuram district requiring the most units due to its high population density. The plan emphasizes efficient E-waste collection, segregation, and recycling, promoting responsible consumption and resource conservation. The study furnishes a "cradle-to-grave" framework for the management of E-waste at local, regional, and national levels, serving as a valuable resource for pollution control boards, regulatory bodies, statutory bodies, and research organizations alike.

Influence of Canadian provincial stewardship model attributes on the cost effectiveness of e-waste management.

This paper presents a comprehensive analysis of e-waste collection and management trends across six Canadian provinces, focusing on e-waste collection rates, provincial stewardship model attributes, program strategies and budget allocations from 2013 to 2020. Temporal and regression analyses were conducted using data from Electronic Product Recycling Association reports. A group characterization based on geographical proximity is proposed, aiming to explore the potential outcomes of fostering collaboration among neighboring provinces. The analysis emphasizes the significant impact of stewardship model attributes on e-waste collection rates, with Quebec emerging as a standout case, showcasing a remarkable 61.5% surge in collection rates. Findings from group analysis reveal a positive correlation between per capita e-waste collection rate and the growth of businesses and collection sites in Western Canada (Group A - British Columbia, Saskatchewan, and Manitoba). This highlights the potential benefits of a coordinated waste management approach, emphasizing the importance of shared resources and collaborative policies. Saskatchewan and Manitoba allocated only 6.6% and 7.0% of their respective budgets to e-waste transfer and storage. British Columbia's observed steady decrease of e-waste collection rate. In Group A, stewards handled 2.18-13.95 tonnes of e-waste during the study period. The cost per tonne of e-waste tended to be lower when more e-waste is managed per steward, suggesting the potential benefits of an integrated e-waste collection and management system.

An investigation on the operational resilience of the Canadian electronic product stewardship program and the recycling business characteristics.

Electronic waste recycling companies have proliferated in many countries due to valuable materials present in end-of-life electronic and electrical equipment. This article examined the business characteristics and management performance of Electronic Products Recycling Association (EPRA), a Canadian nationwide electronic product stewardship organization. The organization's annual performance reports, from 2012 to 2020, for nine Canadian provinces in which it currently operates were aggregated and analyzed. Temporal analysis using regression and Mann-Kendall tests were employed, and five characteristics of EPRA's business were analyzed, including e-waste products collected, number of drop-off locations, efforts to build public awareness, operating expenses, and growth of e-waste stewardship. Results show a decline in the amount of e-waste collected across the provinces, except in New Brunswick, which started its program in 2017. The Mann-Kendall test revealed declining temporal trends in most provinces. Although the collection/drop off sites and stewardship organizations increased astronomically over the study period in Canada, the amounts of e-waste collected decreased. We found that public awareness generally did not increase the amount of e-waste collected, and these campaigns only appeared to be effective in jurisdictions with good accessibility of e-waste recycling. Processing cost accounted for the majority of the e-waste management budget in Canada, and different factors affected the financial success of the stewards differently.

An in-depth analysis and review of management strategies for E-waste in the south Asian region: A way forward towards waste to energy conversion and sustainability.

The soaring rise of electronic and electrical waste (E-waste) leads to significant challenges to the South Asian region, urging for incorporating comprehensive assessment and management strategies. The research dives into the intricacies of E-waste and examines how regulatory barriers, public ignorance, and the limited lifespan of electronic devices all contribute to the significant production of E-waste. This study emphasizes the vital need for ongoing and appropriate management practices by bringing attention to the short lifespan of electronic devices and the resulting generation of E-waste. This work also addresses the increased risks that people who live close to informal recycling sites for electronic waste face, as well as the dangerous substances that are found in them and how they harm the environment and human health. Furthermore, in order to promote circular economies and increase productivity, the study assesses management practices in both developed and developing nations, placing special emphasis on component reuse and recycling. Along with addressing the grave consequences of the illicit E-waste trade on the environment, particularly in developing nations, this review attempts to enlighten stakeholders and policymakers about the vital need for coordinated efforts to address the issues related to E-waste in the South Asian region by offering insights into E-waste assessment and management techniques.

Ghana's recently introduced e-waste regulatory policy: A hope for a better e-waste sector?

Electronic waste (e-waste), often dominated by the informal sector, has had adverse effects on recipient developing countries' economies, health and physical environment. Ghana, over the years, has had support from international organisations to manage its e-waste crisis. Until 2016, there was no e-waste specific policy to guide the management of the sector. In 2016, Ghana passed a regulatory policy - Act 917 - to specifically deal with e-waste, supported by other frameworks such as a regulatory instrument (L.I. 2250), a technical guideline for environmentally sound e-waste management and an e-waste-specific policy, which is currently being developed. However, there is dearth of research on how effectively a regulatory policy such as Act 917 can help address an informally dominated sector whose crude recycling approaches have had great environmental and health impacts. Adapting the analytical framework and intervention theory, key stakeholders within the e-waste sector were interviewed on: the effectiveness of the Act, the challenges confronting them and their involvement in the design and implementation processes. The findings showed that stakeholders were represented at various stages of the process. Informal recyclers were provided with training programmes, health centres and an incentive scheme to minimise burning of electrical and electronic equipment. There however exist many challenges to the sound management of the sector, particularly, the lack of end-to-end recycling facilities, registering and formalising the sector and sequencing of the e-waste policy and regulatory framework. The research concludes by recommending areas for future studies.

Informal E-waste recycling practices and environmental pollution in Africa: What is the way forward?

Globally, e-waste is the fastest growing and most valuable waste-stream. While countries worldwide are increasingly acknowledging the e-waste problem and introducing policies and regulations that deal with e-waste, large quantities of e-waste still go undocumented. Much of these global e-wastes are accumulating in open-dumpsites and landfills in African-countries where they are recycled informally resulting in significant environmental and public-health concerns. Although, there is a plethora of studies on e-waste management and disposal, only a few-studies have focused on African-countries who are major recipients of e-waste. Moreover, despite the attempts to mitigate the problem of e-waste in African-countries, e-waste has remained a major-concern and there are currently very limited workable solutions. This study examines informal e-waste recycling, environmental pollution and the extent of environmental and health impacts in major countries of concern including Ghana, Nigeria, Egypt, Kenya and South Africa. The global e-waste Waste Atlas Report, 2020 identified these countries as major recipients of e-waste. To achieve the aims of this research, previous studies from 2005 to 2022 are collected from various databases and analyzed. Accordingly, this study focuses on environmental pollution and public-health impacts resulting from e-waste dumping and informal recycling practices, illegal transboundary shipment of e-waste to the selected countries, and the interventions of governments and international organizations in reducing the impact of e-waste pollution and informal recycling practices in Africa. Based on the outcomes of this study, practical approaches on the way-forward are recommended. The findings of this study contribute to a growing-body of research on informal e-waste recycling practices in Africa to document that individuals working within e-waste sites and residents in nearby communities are exposed to a number of toxic-substances, some at potentially concerning levels.

Sustainable Behavior with Respect to Managing E-Wastes: Factors Influencing E-Waste Management among Young Consumers.

With the proliferation of technological tools and the advancement in electronic devices and accessories, consumers across the world are changing and upgrading their electronic devices at an alarming rate. However, these developments have raised concerns related to electronic waste (E-waste). E-wastes contain toxic substances which may have a negative impact on both humans and the environment. This issue needs to be addressed by the research community, i.e., what would be the best way to get rid of existing devices? It is clear that countries need to work towards a more sustainable consumption pattern and consumers need to change their behaviour. The present study focuses on sustainable behaviour of consumers in terms of e-waste management. In this context, the study attempts to explore the factors influencing e-waste management among young consumers. In the present study, the Theory of Planned Behavior is extended by including the additional factors Government Policy, Environmental Concern, Financial Benefits and Awareness. A researcher-controlled sampling was employed to collect data from 524 respondents. Partial least square structural equation modelling (PLS-SEM) was used to validate the questionnaire constructs and confirm the relationships among the variables. The findings of the study suggest a significant role for government policy, financial benefits, environmental concerns, attitude, subjective norms, and perceived behavioural control in determining young consumers' behavioural intentions toward the management of e-waste. The study findings have implications for both researchers and marketing practitioners.

Extended producer responsibility in developing economies: Assessment of promoting factors through retail electronic firms for sustainable e-waste management.

The adoption of the extended producers' responsibility (EPR) principle as a mitigation strategy for e-waste management has gained impetus over the past few years. However, e-waste management in developing economies through retail electronic firms' or producer responsibility organization is still inceptive. This study identified and analysed promoting factors of EPR principle adoption through retail electronic firms in the Ghanaian electronic industry. Through extant literature and stakeholders' perspectives, 15 factors were identified as strategic and operational promoting factors, which were evaluated by experts. Subsequently, the grey Decision-Making Trial and Evaluation Laboratory technique was used to analyse the data obtained. The outcome of the study suggests that operational factors have more influence than strategic factors to determine the adoption of the EPR principle. In addition, most of the important operational factors tend to be enabled by both push and pull measures by supply chain stakeholders. In the short term, adopting an advanced deposit recycling refund scheme tends to be the most effective elementary operational factor, which can push retailers to adopt the EPR principle. The significant pull elementary factors that need short-term attention include the opening up and creation of new market opportunities for e-companies as well as resilient and effective resources management. The study findings suggest that Ghana's present policy framework is limited for the adoption of the EPR principle by retail electronic firms. The study contributes to identifying promoting factors for adoption of the EPR principle from the perspectives of both the external and internal stakeholders in the electronic industry with emphasis on push and pull strategy.

A comprehensive review on hazardous aspects and management strategies of electronic waste: Bangladesh perspectives.

Electronic waste (e-waste) contains a variety of electronic components e.g., metals, non-metals, plastics, cables, etc. The excessive generation of e-waste has become a significant concern in the last few decades. The current global e-waste generation is 57.4 million metric tons (MMT) per year. Asia produces the highest amount of e-waste (24.9 MMT) followed by America, Europe, Africa, and Oceania. In Bangladesh, e-waste produces from two sources: its own consumption of electronic devices, which is 0.6 MMT, and imported e-waste from ship breaking yards that is 2.5 MMT in 2021. However, inadequate information on the current state of e-waste generation and management systems in Bangladesh has created a void to establish the future direction for proper handling of e-waste. In this work, the Bangladesh perspective of e-waste has been analyzed. The environmental, health economical forfeiture of e-waste has been discussed. The development of government legislations regarding e-waste have been stated. The establishment of e-waste management has been designed by the life cycle assessment (LCA) and material flow analysis (MFA) models. Moreover, a holistic approach for understanding the possible hazards, the economic feasibility of e-waste processing and viable management models for e-waste in Bangladesh was endeavored in this work to propose systematic future directions and recommendations to improve the current e-waste scenario of Bangladesh.

Consumer awareness and perceptions about e-waste management in semi-urban area of northern Tamil Nadu: A mixed-method approach.

BACKGROUND: The increased use of electronic devices has caused a rise in the generation of e-waste, which is detrimental to the environment and human health. This study aimed to assess consumer awareness, perception, and disposal methods of e-waste management and its determinants in a semi-urban area of northern Tamil Nadu. MATERIALS AND METHODS: It was a mixed-method approach using a sequential explanatory technique with both quantitative and qualitative methods in adult e-consumers. Quantitative data were collected from 350 participants selected via simple random sampling using score-based semi-structured questionnaire. Qualitative data were obtained purposely from eight selected consumers such as recyclers, local leaders, and importers of electronics using key informant interviews. Sociodemographic details and disposal practices were summarized as frequencies and percentages. The independent t-test and linear regression analysis were used to obtain the determinants. Qualitative data were analyzed thematically. RESULTS: Of the 350 participants (208 males and 142 females), the majority (76%), had good knowledge of e-waste management. Consumers (70%) predominantly had a positive perception. Selling e-wastes to scrap dealers (35%) and disposing of household wastes (21%) were common disposal methods. Male gender, higher education (≥10th grade), and skilled and professional workers were significant determining factors of good knowledge and positive perception toward e-waste management. CONCLUSION: There is a need for those in authority to pay special attention to sensitizing the public to the disposal of e-waste practices, ill effects of e-wastes, segregation at collection sites, legislations and laws on e-waste to consumers, and the establishment of disposal sites.

Electronic waste control and management in Ghana: A critical assessment of the law, perceptions and practices.

The aim of the study was to assess the impact of Ghana's hazardous and e-waste control and management Act 917 of 2016 on current e-waste management practices and the level of awareness among key stakeholders (general public, repairers, wholesalers/retailers, recyclers and importers of electronic items) in the Greater Accra Region of Ghana. Both quantitative and qualitative data were collected and examined in this study. Results showed a low level (12%) of awareness among stakeholders on the e-waste legislation. Almost 13% of respondents had been educated on e-waste management. Community engagement and the mass media were the main sources of information on e-waste. Significant associations between background information of respondents and awareness level on 'Ghana's Act 917' were observed. Relative to general e-waste issues, only education and stakeholder showed significant associations with e-waste legislation and management. The main e-waste disposal methods adopted by respondents were disposal at dumpsites (22.7%), repair and reuse (21.1%) and reselling (20.1%). Almost 10% of respondents made changes to their e-waste disposal practices over the past 5 years. These changes were mainly due to the economic benefits derived from reselling e-waste (37.6%) and the perceived adverse impacts of e-waste on the environment (23.9%). Overall, there is the need to intensify awareness on 'Ghana's Act 917', especially issues regarding sustainable e-waste management practices.

Managing e-waste from a closed-loop lifecycle perspective: China's challenges and fund policy redesign.

E-waste is one of the fastest growing streams of solid waste globally, and its effective management has become a focused issue, which requires a deep understanding of the core guiding theory of extended producer responsibility (EPR). Over the past 20 years, China, one of the world's largest producers of electrical and electronic equipment (EEE), has made great efforts to improve e-waste management along with the massive generation of e-waste. In 2012, China implemented a unique EPR-based e-waste fund policy. However, the fund policy is unsustainable due to the challenges of non-closed resource use, informal recycling, and fund imbalance. Beginning with an overview of these challenges, this paper focuses on redesigning the fund policy from a closed-loop lifecycle perspective in order to maintain a balanced development of the resource use loop and the fund system in China's ten-year plan. In doing so, two EPR instruments, recycling content standards and consumer-oriented deposits, are added to the current fund policy. Subsequently, three extension scenarios alternately changed a critical parameter of the model to test the impact on sustainable capabilities. In this way, the sustainable supply of funds and secondary resources for the e-waste industry can be established in China and effectively demonstrate solid waste management in developing countries.

Fuzzy-based adaptive learning network using search and rescue optimization for e-waste management model: case study.

In recent days, the expansion of e-waste disposal should be increased due to environmental hazards, contamination of groundwater, an unconcerned consequence on marine life, human health, and decrease in the fertility of the soil. The majority of the developing countries are facing massive issues in implementing sustainable e-waste management schemes. The unofficial e-waste management schemes in the region of Chandigarh, India, have become a serious dispute for the government and several stakeholders due to human health and environmental effects. To overcome such shortcomings, this paper proposes an efficient e-waste management system using fuzzy c-means based adaptive optimal neural network. Here fuzzy c-means clustering approach is employed to classify the household e-wastes and adaptive optimal neural network is employed to analyze the relative weights as well as the grading of the obstructions. Here, the financial and economic limitations are regarded as the most important obstructions of e-waste formalization. The sensitivity analysis is carried out to verify the structure robustness and address the bias effect. This study assists the lawmakers to create organized strategies for an efficient e-waste management system. The sustainable set of e-waste management system advances the e-waste management in India quality thereby raising the recycling rate to 40%.

Design and development of a fuzzy credibility-based reverse logistics network with buyback offers: A case study.

The ever-growing stream of waste production has become a critical issue for many metropolitan areas. An effective strategy to address this problem has been the concept of reverse logistics (RL). This paper seeks to develop an appropriate product recovery approach for electronic waste generated in an urban area. Consequently, we have proposed an integrated fuzzy RL model with buyback (BB) offers based on the condition of used-products (UPs) at the time of return. However, this strategy contains a significant challenge, which derives from unpredictability surrounding the return rate of UPs due to its dependency on multiple external factors. Hence, a novel fuzzy probability function is developed to approximate UPs' chance of return. Besides that, the mathematical RL network's inherent uncertainty prompted us to employ the fuzzy credibility-based method in the model. Afterward, the model's objectives are locating and allocating collection centres to customer zones, determining flow between facilities and finding the optimal amount of gathered UPs and BB offers. Finally, we applied the model to a case study concerning product recovery in Mashhad city, Iran, and the results have proven its validity and utility.

Analysis of Households' E-Waste Awareness, Disposal Behavior, and Estimation of Potential Waste Mobile Phones towards an Effective E-Waste Management System in Dubai.

During the recent decades, the world has seen ongoing economic and technological development which resulted in the generation of huge volumes of electrical and electronic waste (e-waste). In the Middle East, the United Arab Emirates (UAE) ranks among countries with large e-waste generation due to its consumers' high spending on electronic devices thereby resulting in a high obsolescence rate in the country. Accordingly, this study aims to analyze the e-waste management and recycling practices in the UAE. It takes Dubai as a case study and conducts a structured questionnaire to analyze households' awareness, consumption of electronic devices in general and mobile phones in particular, and the disposal behavior of e-waste. Waste mobile phones is taken as a key representative in this study, in which potential waste mobile phones is estimated using the Approximation 1 method in the period 2021-2030. Results from the survey illustrated gaps among households' awareness and disposal behavior of e-waste, where e-waste recycling rates were noticed to be low. Based on these gaps, strategies were proposed for an effective e-waste management system in the context of Dubai, and were supported by the proposal of an e-waste legislation framework in the UAE.

Reuse assessment of WEEE: Systematic review of emerging themes and research directions.

The reuse of Waste Electrical and Electronic Equipment (WEEE) is deemed the best end-of-life option in terms of the environmental impact and socio-economic benefits. Taking this cue, this paper applies a systematic literature review to map the existing knowledge base to present the major and emerging themes of the reuse assessment of WEEE. In all, 12,216 articles published from 2005 to 2019 in the Web of Science, ProQuest, and Google Scholar are collected, from which 331 articles are shortlisted for review. The shortlisted articles are divided into two sub-periods 2005-2014 and 2015-2019 to draw out the development of the research themes and the contribution of the recent research articles to the literature on WEEE reuse assessment. Bibliographic coupling combined with keyword analysis is performed using SciMat and VOSViewer. The results inform that the major ongoing themes are Consumer behaviour towards use, disposal, collection, reuse, repair and recycling of WEEE; Assessing the potential of WEEE for reuse; Product recovery strategy and market analysis for WEEE remanufacturing; and Material flow analysis of WEEE in circular economy. The research themes of Informal WEEE management in developing countries; Impact of government subsidy on WEEE management; and Product service system and circular economy deserve further attention. In the articles reviewed, mobile phones and computers are extensively studied for WEEE reuse assessment followed by refrigerators and televisions. Assessing the environmental impact and legal aspects of WEEE reuse, cross-border movements and flow in secondary markets, policies and regulations on the purchase of reprocessed WEEE, and the reprocessing and revenue made by the informal sector in developing countries are possibilities for future research.

Multi-Criteria Decision Making Approaches Applied to Waste Electrical and Electronic Equipment (WEEE): A Comprehensive Literature Review.

The global demand for electrical and electronic equipment has undergone continuous growth in recent years due to the effect of industrialization and technological development. This indicates substantial quantities of e-waste that need to be managed properly to reduce their environmental impact and to avoid inappropriate forms of disposal. The purpose of this paper is to review the most popular multi-criteria decision-making approaches applied to the management of waste electrical and electronic equipment, analyzing how they are used to contribute to the improvement of management strategies along the entire supply chain. For this purpose, a methodological protocol for the collection, selection, and analysis of the scientific literature was applied, identifying 44 papers on which to conduct this study. The results showed that numerous authors have developed multi-criteria approaches, with particular attention to recycling phase. The analytic hierarchy process is the most widespread multi-criteria approach, often coupled with VIKOR, DELPHI, and TOPSIS methods. The numerous decision making criteria adopted cover different reference dimensions: environmental, economic, social, technical, and legal. Considering environmental aspects also in decision making processes means enhancing the relevance of this dimension, as well as encouraging practices that reduce the impact of toxic substances on the environment and living organisms.

Ticking time bomb: implications of the COVID-19 lockdown on e-waste management in developing countries.

The COVID-19 pandemic has altered the course of events globally since the outbreak of coronavirus disease (COVID-19) in late 2019 giving further credence to the long-standing belief that the world is indeed a global village. There have been different responses by countries to the raging pandemic including the imposition of lockdowns, quarantine and isolation. The imposition of lockdowns, whether full or partial, has not been without major consequences, which has led to information, communication and technological (ICT)-based measures to minimise the effect of the lockdown and as an alternative to physical interactions. The use of ICT devices to bridge the gaps created by the lockdown on schools, businesses and other sectors has led to the increased use of electronic devices. The challenge of electronic waste (e-waste) management in developing countries has been around for a while and the increased use of electronic devices is likely to compound the challenge during and post COVID-19. Whilst the development of ICT-based options as viable alternatives to face-to-face interactions may not be a negative development, this article argues that the existing frameworks are inadequate to manage the resultant increase in e-waste in most developing countries and that there is need now more than ever before for developing countries to exercise caution in embracing these ICT-based options without putting in place measures to ensure that there is increased capacity to manage and dispose of the e-waste created.