MXene Based Flame Retardant and Electrically Conductive Polymer Coatings.

Modern polymer coatings possess tremendous multifunctionalities and have attracted immense research interest in recent decades. However, with the expeditious development of technologies and industries, there is a vast demand for the flame retardancy and electrical conductivity of engineered polymer coatings. Traditional functional materials that render the polymer coatings with these properties require a sophisticated fabrication process, and their high mass gains can be a critical issue for weight-sensitive applications. In recent years, massive research has been conducted on a newly emerged two-dimensional (2D) nanosize material family, MXene. Due to the excellent electrical conductivity, flame retardancy, and lightweightness, investigations have been launched to synthesise MXene-based polymer coatings. Consequently, we performed a step-by-step review of MXene-involved polymer coatings, from solely attaching MXene to the substrate surface to the multilayered coating of modified MXene with other components. This review examines the performances of the fire safety enhancement and electrical conductivity as well as the feasibility of the manufacturing procedures of the as-prepared polymer composites. Additionally, the fabricated polymer coatings' dual property mechanisms are well-demonstrated. Finally, the prospect of MXene participating in polymer coatings to render flame retardancy and electrical conductivity is forecasted.

Enhanced photodynamic therapy of curcumin using biodegradable PLGA coated mesoporous silica nanoparticles.

Since the available treatments are not highly effective to combat cancer, therefore, the alternative strategies are unavoidable. Photodynamic therapy (PDT) is one of the emerging approaches which is target specific and minimally invasive. This study explores the successful development of Poly (D,L-lactide-co-glycolide) (PLGA) coated mesoporous silica nanoparticles (MSNs) and their augmented effects achieved by integrating curcumin (Cur) and cetyltrimethylammonium bromide (CTAB) in the polymeric layer and silica's pores, respectively. The synthesized nanocarriers (Cur-PLGA-cMSNs) have shown preferential targeting to the cellular organelles facilitated by CTAB's and Cur's affinity to mitochondria. CTAB and Cur-based PDT induced oxidative stress and generation of reactive oxygen species (ROS), resulting in dysfunctional mitochondria and triggered apoptotic pathways. PLGA coating has produced multifunctional effects, including; gatekeeping effects at pore openings, providing an extra loading site, enhancing the hemocompatibility of MSNs, and masking the free cur-related prolonged coagulation time. Cur-PLGA-cMSNs, as a multifaceted and combative approach with synergistic effects demonstrate promising potential to enhance outcomes in cancer treatment.

Hydrophobic iron oxide nanoparticles: Controlled synthesis and phase transfer via flash nanoprecipitation.

Iron oxide nanoparticles (IONPs) synthesized via thermal decomposition find diverse applications in biomedicine owing to precise control of their physico-chemical properties. However, use in such applications requires phase transfer from organic solvent to water, which remains a bottleneck. Through the thermal decomposition of iron oleate (FeOl), we systematically investigate the impact of synthesis conditions such as oleic acid (OA) amount, temperature increase rate, dwell time, and solvent on the size, magnetic saturation, and crystallinity of IONPs. Solvent choice significantly influences these properties, manipulating which, synthesis of monodisperse IONPs within a tunable size range (10-30 nm) and magnetic properties (75 to 42 Am2Kg-1) is obtained. To enable phase transfer of IONPs, we employ flash nanoprecipitation (FNP) for the first time as a method for scalable and precise size control, demonstrating its potential over conventional methods. Poly(lactic-co-glycolic acid) (PLGA)-coated IONPs with hydrodynamic diameter (Hd) in the range of 250 nm, high colloidal stability and high IONPs loadings up to 43% were obtained, such physicochemical properties being tuned exclusively by the size and hydrophobicity of starting IONPs. They showed no discernible cytotoxicity in human dermal fibroblasts, highlighting the applicability of FNP as a novel method for the functionalization of hydrophobic IONPs for biomedicine.

In Vitro Corrosion of Polyester-Coated Magnesium Alloy under pH-Static Conditions.

The resorption rate of bioresorbable implants requires tuning to match the desired field of application. The use of Mg as implant material is highly advantageous, as it provides sufficient mechanical strength combined with its biodegradability. Consequently, the implant vanishes after it has served its intended purpose, allowing the complete restoration of natural tissue and organ function. However, a biodegradable Mg implant requires a biodegradable coating to slow the rate of Mg corrosion, as a permanent coating would negate the benefits of using Mg as an implant material. Therefore, degradable polymers are the materials of choice, especially polyester-based coatings, such as PLLA, as they have been proven in clinical practice over the long term. Within this work, the degradation retarding effect of a physical barrier in form of four clinically relevant polyester-based coatings, poly-l-lactide (PLLA), poly-l-lactide-co-glycolide (PLGA), poly(l-lactide-co-PEG) triblock copolymer (PLLA-co-PEG), and polydioxanone (PDO), is investigated in vitro under pH-static conditions using CO2 gas to compensate pH changes due to Mg corrosion. Coating thicknesses of 7.5 to 8.3 µm were comparable to commercially available stent systems. Quantitative analysis of magnesium concentration in buffered test medium by a photometric assay allows real-time monitoring. Shielding effect of different polyesters through polymer coating and formation of a protective passivation layer beneath the polymer coating was observed and characterized using SEM and EDX techniques. Our finding was that even imperfect polymer layers provide a considerable protective effect, and the used in vitro setup matches reported in vivo observations regarding elemental composition of corrosion products.

Microneedle patch casting using a micromachined carbon master for enhanced drug delivery.

For successful treatment of diseases, sufficient therapeutics must be provided to the body. Microneedle applications in therapeutic delivery and analytics sampling are restricted because of various issues, including smaller area for drug loading and analytics sampling. To achieve sufficient drug loading and analytics sampling and improve drug penetration while maintaining painless administration, patch-type microneedle arrays were designed and fabricated using polymer casting from a conical cavity mold. Microcavities were formed on a carbon plate via micromechanical machining. A porous polymer layer was coated on a microneedle patch (MNP). The pores of the porous polymer layer provided space and channels for drug delivery. A pH-sensitive polymer layer was employed to cap the porous polymer layer, which prevented drug leakage during storage and provided a stimulus drug release in response to body pH conditions. The drug can be delivered through holes connected to both sides of the patch. The drug release of the MNP was investigated in vitro and in vivo and showed conceptual proof that these MNs have the potential to enhance treatment protocols for various diseases with the flexibility of coating and therapeutic materials and offer significant scope for further variations and advancement.

Delayed cerebral complications associated with endovascular catheter coil embolization for pulmonary venous shunts mimicking cerebral inflammatory diseases.

Introduction: Hydrophilic polymer embolism in the brain is a delayed complication of cerebral angiography or endovascular therapy. Herein, we report a rare case of a hydrophilic polymer embolism in the brain due to endovascular catheter coil embolization of pulmonary venous shunts. Case report: A 16-year-old female presented with headache, dizziness, nausea, and dysesthesia in the left upper limb. Brain magnetic resonance imaging (MRI) revealed multiple bilateral subcortical white matter lesions with nodular gadolinium enhancement lesions surrounded with edema. Two weeks before onset, the patient underwent endovascular catheter coil embolization with two coils for two systemic-to-pulmonary venous shunts. We suspected that her multiple cerebral lesions were delayed allergic complications due to a catheter hydrophilic polymer-coating embolism after endovascular catheter coil embolization. Corticosteroid treatment rapidly improved neurological symptoms and MRI findings. Conclusion: To avoid unnecessary brain biopsy, careful history taking of previous catheterization is essential among patients presenting with focal deficits and punctate-enhancing brain lesions for the diagnosis of hydrophilic polymer embolism.

Investigation into Effects of Coating on Stress Corrosion of Cable Bolts in Deep Underground Environments.

Due to the intricate and volatile nature of the service environment surrounding prestressing anchoring materials, stress corrosion poses a significant challenge to the sustained stability of underground reinforcement systems. Consequently, it is imperative to identify effective countermeasures against stress corrosion failure in cable bolts within deep underground environments, thereby ensuring the safety of deep resource extraction processes. In this study, the influence of various coatings on the stress corrosion resistance of cable bolts was meticulously examined and evaluated using specifically designed stress-corrosion-testing systems. The specimens were subjected to loading using four-point bending frames and exposed to simulated underground corrosive environments. A detailed analysis and comparison of the failure patterns and mechanisms of specimens coated with different materials were conducted through the meticulous observation of fractographic features. The results revealed stark differences in the stress corrosion behavior of coated and uncoated bolts. Notably, epoxy coatings and chlorinated rubber coatings exhibited superior anti-corrosion capabilities. Conversely, galvanized layers demonstrated the weakest effect due to their sacrificial anti-corrosion mechanism. Furthermore, the effectiveness of the coatings was found to be closely linked to the curing agent and additives used. The findings provide valuable insights for the design and selection of coatings that can enhance the durability and reliability of cable bolts in deep underground environments.

Chitosan-coated paper packaging for specialty coffee beans: Coating characterization, bean and beverage analysis.

Cellulose-based packaging has received great attention due to its characteristics of biodegradability, sustainability, and recyclability. Natural polymer coatings are usually applied to the paper surface to enhance the barriers to water vapour and improve the mechanical properties. A chitosan-based coating for paper packaging was developed in this work to store specialty roasted coffee beans, evaluating two samples of chitosan (Sigma® and molasses chitosan), and following the physico-chemical and microbiological characteristics of coffee beans along a period of 60 days. Sensory tests (Ranking Descriptive Analysis and Preference Test) were applied to the beverage prepared with the roasted and ground coffee beans stored in each packaging. Thin chitosan films provided good coverage and adhesion on the paper. Improved mechanical properties and lower water permeability were observed in the chitosan-coated papers. The physicochemical and microbiological characteristics of the coffee beans were not influenced by the packaging along 60 days of storage. The molasses chitosan coating resulted in slightly darker roasted beans. In sensory evaluation, there is a clear difference between the chitosan samples, so that molasses chitosan-coated packaging had higher scores compared to Sigma® chitosan treatment for flavor and global impression in the preference analysis of the beverage. The molasses chitosan-coated packaging had three to four more consumers attributing the highest scores for the beverage prepared with the roasted beans stored in this type of packaging.

Polyallylamine Binds to Aß Amyloid and Inhibits Antibody Recognition.

Protein amyloids have attracted attention for their application as functional amyloid materials because of their strong properties, such as high resistance to chemical or biological degradation, despite their medical issues. Amyloids can be used for various applications by modifying the amyloid surface with functional materials, such as proteins and polymers. In this study, we investigated the effect of polyallylamine (PAA), a functional cationic polymer as a candidate for amyloid modification, on the amyloids formed from amyloid ß (Aß) peptide. It was demonstrated for the first time that PAA can bind to Aß amyloids through fluorescence observations and the quenched emission from the tyrosine at site 10 near the fibrillogenic core. These results suggest that PAA could be used to develop new functional amyloids. However, notably, coating Aß amyloid with PAA could affect conventional amyloid detection assays such as thioflavin T assay and detection using antibodies. Thus, our results also indicate that consideration would be necessary for the analysis of functional amyloids coated with various polymers.

Liposomes Coated with Novel Synthetic Bifunctional Chitosan Derivatives as Potential Carriers of Anticancer Drugs.

In this study, liposomes coated with novel multifunctional polymers were proposed as an innovative platform for tumor targeted drug delivery. Novel Folic acid-Cysteine-Thiolated chitosan (FTC) derivatives possessing active targeting ability and redox responsivity were synthesized, characterized, and employed to develop FTC-coated liposomes. Liposomes were characterized for size, surface charge and drug encapsulation efficiency before and after coating. The formation of a coating layer on liposomal surface was confirmed by the slight increase in particle size and by zeta-potential changes. FTC-coated liposomes showed a redox-dependent drug release profile: good stability at physiological conditions and rapid release of liposome-entrapped calcein in presence of glutathione. Moreover, the uptake and cytotoxic activity of doxorubicin-loaded FTC-coated liposomes was evaluated on murine B16-F10 and human SKMEL2 melanoma cancer cells. Results demonstrated enhanced uptake and antitumor efficacy of FTC-coated liposomes compared to control chitosan-coated liposomes in both cancer lines, which is attributed to higher cellular uptake via folate receptor-mediated endocytosis and to triggered drug release by the reductive microenvironment of tumor cells. The proposed novel liposomes show great potential as nanocarriers for targeted therapy of cancer.

Non-Electroconductive Polymer Coating on Graphite Mitigating Electrochemical Degradation of PTFE for a Dry-Processed Lithium-Ion Battery Anode.

Polytetrafluoroethylene (PTFE)-based dry process for lithium-ion batteries is gaining attention as a battery manufacturing scheme can be simplified with drastically reducing environmental damage. However, the electrochemical instability of PTFE in a reducing environment has hampered the realization of the high-performance dry-processed anode. In this study, we present a non-electroconductive and highly ionic-conductive polymer coating on graphite to mitigate the electrochemical degradation of the PTFE binder and minimize the coating resistance. Poly(ethylene oxide) (PEO) and poly(vinylidene fluoride-trifluoroethylene-chlorofluoroethylene) (P(VDF-TrFE-CFE)) coatings on the anode material effectively inhibit the electron transfer from graphite to PTFE, thereby alleviating the PTFE breakdown. The graphite polymer coatings improved initial Coulombic efficiencies of full cells from 67.2% (bare) to 79.1% (PEO) and 77.8% (P(VDF-TrFE-CFE)) and increased initial discharge capacity from 157.7 mAh g(NCM)-1 (bare) to 185.1 mAh g(NCM)-1 (PEO) and 182.5 mAh g(NCM)-1 (P(VDF-TrFE-CFE)) in the full cells. These outcomes demonstrate that PTFE degradation in the anode can be surmounted by adjusting the electron transfer to the PTFE.

Platelet volume indices and von Willebrand factor levels in blood exposed to polymer- or heparin-coated membrane oxygenators.

INTRODUCTION: To understand the behavior of platelet volume indices and the von Willebrand factor (VWF), in vitro experiments using whole human blood were performed with extracorporeal circulation (ECC) circuits, including membrane oxygenators coated with acrylate copolymer (ACP) or immobilized heparin (IHP). METHODS: Heparinized blood was circulated through two distinct experimental circuits: an ACP-coated reservoir and tubes, as well as membranes coated with either ACP or IHP (comprising five pieces of each type). The platelet distribution width, mean platelet volume (MPV), platelet large cell ratio (P-LCR), VWF quantity (VWFQ), and VWF activity (VWFA) were measured at 0, 8, 16, 24, and 32 h in each experiment. A two-way analysis of variance (ANOVA) was performed to determine whether the coating type or circulation duration affected the transition of each measurement. RESULTS: Two-way ANOVA indicated that the transitions of MPV, P-LCR, and VWFA were significantly affected by the circulation duration (p = 0.030, 0.001, and <0.001, respectively) and that the transitions of VWFQ and VWFA were significantly affected by the coating type (p = 0.022 and 0.006, respectively). Factor interactions between the coating type and circulation duration were not observed for each transition (p > 0.05). CONCLUSIONS: Our findings suggest that P-LCR is a good index for platelet activation in blood-circulating ECC and that VWFA and VWFQ are significantly attenuated in blood-circulating ECC with ACP-coated membranes, indicating the advantage of IHP coating regarding platelet activation.

In Situ Construction of a Polymer Coating Layer on the LiNi0.8Co0.1Mn0.1O2 Cathode for High-Performance Lithium-Ion Batteries.

Lithium-ion batteries (LIBs) are known for their high energy density but exhibit poor cyclic stability and safety risks due to side reactions between the electrode and electrolyte. To address these issues, a novel approach involving construction of a polymer coating layer (PCL) via in situ self-polymerization using 2,2,3,4,4,4-hexafluorobutyl methacrylate (HFBM) as an electrolyte additive on the cathode is proposed. The PCL endows the electrolyte with a high onset oxidation potential (4.78 V) and lithium-ion transference number (0.52). The uniform and robust in situ constructed PCL can effectively inhibit the severe irreversible side reactions and suppress harmful reactions, thus providing a protective barrier against degradation. The resulting Li||LiNi0.8Co0.1Mn0.1O2 batteries exhibit an improved discharge capacity retention of 80% at 1C over 100 cycles. These results demonstrate that the in situ self-polymerization strategy holds promising potential for enhancing LIB performance and long-term stability, especially when high-voltage cathode materials are used.

Carboxymethyl chitosan and octadecylamine-coated liposome-containing WPTS: design, optimization, and evaluation.

Liposomes (LPs) are a delivery system for stabilizing pharmaceuticals with limited use due to their propensity to congregate and fuse. A proposed method of addressing these problems is polymer coating. In this study, the potential of octadecylamine (ODA)-coated liposomes and carboxymethyl chitosan (CMCS/ODA-LPs) for enhancing Wacao pentacyclic triterpene saponin (WPTS) transport capacity was investigated. CMCS/ODA-LPs were produced by electrostatic adsorption and thin-film hydration. Response surface methodology (RSM) was employed to enhance the process and encapsulation efficiency (EE) for optimum drug encapsulation efficiency. The synthesized WPTS-CMCS/ODA-LPs were uniformly dispersed in a circular shape, and during 14 days of storage at 4 °C, the particle size and morphology did not significantly change. Vesicle size, zeta potential, polydispersity index (PDI), and entrapment efficiency (%) were 179.1 ± 7.31 nm, -29.6 ± 1.35 mV, 0.188 ± 0.052, and 75.62 ± 0.43, respectively. The hemolysis test revealed that WPTS-CMCS/ODA-LPs were sufficiently biocompatible. Compared to WPTS-LPs, WPTS-CMCS/ODA-LPs consistently showed a much more significant cytotoxic effect on cancer cells. Early and WPTS-CMCS/ODA-LPs-induced apoptosis resulted in almost seven times more cell death than the control. Compared to physiological pH 7.3, the pH-sensitive CMCS coupled LPs increased drug release at acidic pH 6.5. These findings suggest the efficacy of pH-sensitive CMCS/ODA-LPs as a medication delivery method for WPTS.

Polymer Coating with Balanced Coordination Strength and Ion Conductivity for Dendrite-Free Zinc Anode.

Decorating Zn anodes with functionalized polymers is considered as an effective strategy to inhibit dendrite growth. However, this normally brings extra interfacial resistance rendering slow reaction kinetics of Zn2+ . Herein, a poly(2-vinylpyridine) (P2VP) coating with modulated coordination strength and ion conductivity for dendrite-free Zn anode is reported. The P2VP coating favors a high electrolyte wettability and rapid Zn2+ migration speed (Zn2+ transfer number, tZn 2+ = 0.58). Electrostatic potential calculation shows that P2VP mildly coordinates with Zn2+ (adsorption energy = -0.94 eV), which promotes a preferential deposition of Zn along the (002) crystal plane. Notably, the use of partially (26%) quaternized P2VP (q-P2VP) further reduces the interfacial resistance to 126 Ω, leading to a high ion migration speed (tZn 2+ = 0.78) and a considerably low nucleation overpotential (18 mV). As a result of the synergistic effect of mild coordination and partial electrolysis, the overpotential of the q-P2VP-decorated Zn anode retains at a considerably low level (≈46 mV) over 1000 h at a high current density of 10 mA cm-2 . The assembled (NH4 )2 V6 O16 ·1.5H2 O || glass fiber || q-P2VP-Zn full cell reveals a lower average capacity decay rate of only 0.018% per cycle within 500 cycles at 1 A g-1 .

Antibiofilm Property and Biocompatibility of Siloxane-Based Polymer Coatings Applied to Biomaterials.

Biofilm infections sometimes occur on biomaterials inserted into the body because biomaterials can block the attack of immune cells such as macrophages, promoting biofilm formation by invading bacteria. Owing to their use in antifouling applications, including biofilm formation, siloxane-based polymer coatings are considered a promising method to prevent biofilm formation on the surface of biomaterials. In this study, we explored the antibiofilm property and biocompatibility of siloxane-based polymer coatings. Biofilm formation and cytotoxicity tests were performed using Escherichia coli and Staphylococcus epidermidis to quantify the biofilms while U937 cells were used to measure the time course of viable cell concentration and viability, respectively. In both the biofilm formation and cytotoxicity tests, stainless steel SUS316L plates and titanium plates coated with the siloxane-based polymer and sterilized in an autoclave were used as the biomaterials. The amount of biofilm formed on the polymer-coated titanium plate was substantially higher than that on a noncoated titanium plate in the case of S. epidermidis. The viable cell concentration and viability of U937 cultured on the polymer-coated titanium plate were lower than those of U937 cultured on the noncoated titanium plate. The same trend was observed between polymer-coated and noncoated SUS316L plates. These results indicate that the siloxane-based polymer coatings need additional treatment to achieve a satisfactory antibiofilm property and that they are sensitive to autoclave treatment, resulting in cytotoxicity.

Aligned skeletal muscle assembly on a biofunctionalized plant leaf scaffold.

Decellularized plant scaffolds have drawn attention as alternative tissue culture platforms due to their wide accessibility, biocompatibility, and diversity of innate microstructures. Particularly, in this work, monocot leaves with innate uniaxial micropatterned topography were utilized to promote cell alignment and elongation. The leaf scaffold was biofunctionalized with poly(PEGMEMA-r-VDM-r-GMA) copolymer that prevented non-specific protein adsorption and was modified with cell adhesive RGD peptide to enable cell adhesion and growth in serum-free media. The biofunctionalized leaf supported the adhesion, growth, and alignment of various human cells including embryonic stem cells (hESC) derived muscle cells. The hESC-derived myogenic progenitor cells cultured on the biofunctionalized leaf scaffold adopted a parallel orientation and were elongated along the leaf topography. These cells showed significant early myogenic differentiation and muscle-like bundled myotube formation. The aligned cells formed compact myotube assemblies and showed uniaxial muscle contraction under chemical stimulation, a critical requirement for developing functional skeletal muscle tissue. Polymer-functionalized plant leaf scaffolds offer a novel human cell culture platform and have potential in human tissue engineering applications that require parallel alignment of cells. STATEMENT OF SIGNIFICANCE: Plant scaffolds are plentiful sources in nature and present a prefabricated construct to present topographical cues to cells. Their feature width is ideal for human cell alignment and elongation, especially for muscle cells. However, plant scaffolds lack proteins that support mammalian cell culture. We have developed a polymer coated leaf scaffold that enables cell adhesion and growth in serum-free media. Human muscle cells cultured on the biofunctionalized leaf, aligned along the natural parallel micro-patterned leaf topography, and formed muscle-like bundled myotube assemblies. These assemblies showed uniaxial muscular contraction, a critical requirement for developing functional skeletal muscle tissue. The biodiversity of the plant materials offers a novel human cell culture platform with potential in human tissue engineering.

3D-printed biosurfactant-chitosan antibacterial coating for the prevention of silicone-based associated infections.

Infections associated with the surfaces of medical devices represent a critical problem due to biofilm formation and the growing resistance towards antibacterial drugs. This is particularly relevant in commonly used invasive devices such as silicone-based ones where a demand for alternative antibiofilm surfaces is increasing. In this work, an antimicrobial chitosan-biosurfactant hydrogel mesh was produced by 3D-printing. The 3D structure was designed to coat polydimethylsiloxane-based medical devices for infection prevention. Additionally, the porous 3D structure allows the incorporation of customized bioactive components. For this purpose, two biosurfactants (surfactin and sophorolipids) were biosynthesized and tested for their antimicrobial activity. In addition, the printing of surfactant-chitosan-based coatings was optimized, and the resulting 3D structures were characterized (i.e., wettability, FTIR-ATR, antimicrobial activity, and biocompatibility). Compared with surfactin, the results showed a better yield and higher antibacterial activity against Gram-positive bacteria for sophorolipids (SLs). Thus, SLs were used to produce chitosan-based 3D-printed coatings. Overall, the SLs-impregnated coatings showed the best antibacterial activity against Staphylococcus aureus planktonic bacteria (61 % of growth inhibition) and antibiofilm activity (2 log units reduction) when compared to control. Furthermore, concerning biocompatibility, the coatings were cytocompatible towards human dermal fibroblasts. Finally, the coating presented a mesh suitable to be filled with a model bioactive compound (i.e., hyaluronic acid), paving the way to be used for customized therapeutics.

Poly(l-lactide)/polycaprolactone based multifunctional coating to deliver paclitaxel/VEGF and control the degradation rate of magnesium alloy stent.

Despite significant advancements made in cardiovascular stents, restenosis, thrombosis, biocompatibility, and clinical complications remain a matter of concern. Herein, we report a biodegradable Mg alloy stent with a dual effect of the drug (Paclitaxel) and growth factor (VEGF) release. To mitigate the fast degradation of Mg alloy, inorganic and organic coatings were formed on the alloy surface. The optimized hierarchal sequence of the coating was the first layer consisting of magnesium fluoride, followed by poly(l-lactide) and hydroxyapatite coating, and finally sealed by a polycaprolactone layer (MgC). PLLA and HAp were used to increase the adhesion strength and biocompatibility of the coating. Paclitaxel and VEGF were loaded in the final PCL layer (Mg-C/PTX-VEGF). As compared to bare Mg alloy (28 % weight loss), our MgC system showed (3.1 % weight loss) successful decrease in the degradation rate. Further, the in vitro biocompatibility illustrated the highly biocompatible nature of our drug and growth factor-loaded system. The in vivo results displayed that the drug loading decreased the inflammation and neointimal hyperplasia as indicated by the α-SMA and CD-68 antibody staining. The growth factor helped in the endothelialization which was established by the FLKI and ICAM antibody staining of the tissue.

Molecular Imaging Investigations of Polymer-Coated Cerium Oxide Nanoparticles as a Radioprotective Therapeutic Candidate.

Cerium oxide nanoparticles (CONPs) have a unique surface redox chemistry that appears to selectively protect normal tissues from radiation induced damage. Our prior research exploring the biocompatibility of polymer-coated CONPs found further study of poly-acrylic acid (PAA)-coated CONPs was warranted due to improved systemic biodistribution and rapid renal clearance. This work further explores PAA-CONPs' radioprotective efficacy and mechanism of action related to tumor microenvironment pH. An ex vivo TUNEL assay was used to measure PAA-CONPs' protection of the irradiated mouse colon in comparison to the established radioprotector amifostine. [18F]FDG PET imaging of spontaneous colon tumors was utilized to determine the effects of PAA-CONPs on tumor radiation response. In vivo MRI and an ex vivo clonogenic assay were used to determine pH effects on PAA-CONPs' radioprotection in irradiated tumor-bearing mice. PAA-CONPs showed excellent radioprotective efficacy in the normal colon that was equivalent to uncoated CONPs and amifostine. [18F]FDG PET imaging showed PAA-CONPs do not affect tumor response to radiation. Normalization of tumor pH allowed some radioprotection of tumors by PAA-CONPs, which may explain their lack of tumor radioprotection in the acidic tumor microenvironment. Overall, PAA-CONPs meet the criteria for clinical application as a radioprotective therapeutic agent and are an excellent candidate for further study.