Feasibility of increasing calcium content of drinking tap water following quality regulations to improve calcium intake at population level.

Background: Calcium intake is below recommendations in several parts of the world. Improving calcium intake has benefits not only for bone health but also helps to prevent pregnancy hypertension disorders. Calcium concentration of tap water is usually low The aim of the present study was to determine the maximum amount of calcium that can be added to tap water while complying with drinking water Argentine regulations. Methods: Tap water samples were collected from the Province of Buenos Aires (Argentina). Physicochemical properties and saturation index were measured. Different incremental concentrations of calcium chloride were added to the experimental aliquots. Results: Baseline water had a mean calcium concentration of 22.00 ± 2.54 mg/L, water hardness of 89.9 ± 6.4 mg/L CaCO 3, and a saturation index of -1.50 ± 0.11. After the addition of 0.4554 ± 0.0071 g of salt, water hard-ness reached 355.0 ± 7.1 mg/L CaCO 3, a calcium concentration of 140.50 ± 2.12 mg/L, and a saturation index -0.53 ± 0.02. Conclusions: This study shows that at laboratory level it is feasible to increase calcium concentration of drinking water by adding calcium chloride while complying with national standards. Calcium concentration of drinking tap water could be evaluated and minimum calcium concentration of tap water regulated so as to improve calcium intake in populations with low calcium intake.

Calcium chloride poisoning: an autopsy case report and histologic features.

Calcium chloride, which is commonly used in de-icing agents and desiccants, is known for the potential harm it can cause through skin contact, oral ingestion, or intravenous administration. The current paper reports on an autopsy case of a 68-year-old woman who died after ingesting an unknown substance. Histopathological examination revealed coagulative necrosis in the esophagus and ionized blood calcium levels that were significantly higher than normal. Calcium chloride was detected in the contents of the water bottle collected at the scene. These results are expected to make a significant contribution to the limited literature on fatal outcomes from calcium chloride ingestion, while emphasizing the need for heightened awareness and education about the risks of commonly available chemicals.

Improving Cuticle Thickness and Quality Traits in Table Grape cv. 'Italia' Using Pre-Harvest Treatments.

Table grape viticulture, due to the impact of climate change, will have to face many challenges in the coming decades, including resistance to pathogens and physiological disorders. Our attention was focused on fruit cracking due to its ubiquitous presence in several species. This study explores the effects of three different treatments on the epidermis and cuticle of table grape berries by evaluating the impact of the girdling technique on various fruit quality parameters, including cuticle thickness, sugar content, acidity, color, bunch weight, and rheological properties. The treatments were (1) calcium chloride (CaCl2), (2) calcium chloride + salicylic acid (CaCl2 + SA), and (3) calcium chloride + Ascophyllum nodosum (CaCl2 + AN), with and without girdling, plus an untreated control. This research was conducted over the 2021-2022 growing season in a commercial vineyard in Licodia Eubea, Sicily, Italy. The results indicate significant variations in cuticle thickness and other qualitative traits throughout the growth and ripening phases, with notable differences depending on the treatment used. This study's findings suggest that specific treatments can influence the structural integrity of the grape cuticle, potentially impacting the fruit's susceptibility to cracking and overall marketability. The findings provide valuable insights into the role of chemical treatments and cultural techniques in enhancing fruit quality and resistance to environmental stresses in table grape cultivation.

Effect of calcium chloride blanching combined with acetic acid soaking pretreatment on oil absorption of fried potato chips.

This study investigated the effect of calcium chloride (CaCl2) combined with acetic acid (AA) pretreatment on the oil absorption of potato chips and explored the possible mechanisms influencing oil absorption. Results indicated that compared with hot water blanching, the combination of 0.3% CaCl2 blanching and AA soaking for 2-8 h pretreatment was found to reduce oil content by 10.52%-12.68% and significantly improve the crispness and color of fried potato chips. Microstructural and textural analyses revealed that the main reason for the reduction in oil content was the promotion of pectin gelation in the cell wall by CaCl2 and AA. However, it was observed that prolonged AA soaking time and high-concentration CaCl2 blanching led to an increase in total oil content and decrease in brittleness. Based on the results of surface roughness and moisture content analyses, it was suggested that the CaCl2 and AA pretreatments affected surface roughness and moisture content, thereby increasing oil absorption and reducing brittleness during frying.

Improvement of jelly 3D printing using ultrasound treatment and calcium chloride.

This study investigated the effects of ultrasound treatment or calcium chloride (CaCl2) addition on the physical properties of jelly formulations. Elastic modulus (G'), loss modulus (G"), tan δ, shear modulus, yield stress (τ0), phase angle (δ), and gel strength were the parameters selected to describe the requirements of jelly printing, such as fidelity, shape retention, and extrudability. Ultrasound treatment of the jelly formulation without pectin increased the G' and shear moduli values, while decreasing the δ and gel strength. The addition of CaCl2 to the jelly formulation with pectin increased the G', G", shear modulus, τ0, and gel strength but lowered the tan δ and δ values. Both ultrasound treatment and CaCl2 addition improved the jelly printing requirements and demonstrated the potential to control the physical properties of jelly formulations for 3D printing using fused deposition modeling.

Experimental study on soil improvement by electrochemical injection of calcium chloride solutions with time interval.

An improved electroosmotic method is proposed in this paper to enhance the non-uniform effect and efficiency of electroosmotic process. Such method is electroosmotic flow with injection of calcium chloride through the anode, followed by injection through the central tube (a tube at the midpoint between the anode and the cathode) with a suitable time interval between injections. Experimental results indicate that using this method can significantly improve the non-uniform reduction in water content throughout the soil, mitigate the formation of cracks in the anode section, and therefore considerably inhibit the increase in the electric resistance. After treatment, the drained water could be raised to 3.59 times more than that of pure electroosmotic flow, and 1.3 times that of simultaneous injection through both the anode and the central tube with considerably slight increase in power consumption. Moreover, the area of cementation was also expanded, approximately twice larger than that of pure electroosmotic flow and one and a half that of simultaneous injection. It is also worth noting that the proposed method performs better with the same power consumption. The results demonstrate that electroosmotic flow with a suitable time interval between injections could improve the efficiency of electroosmotic process and expand the treatment region in soils, hence can be a promising and economic technique for soil improvement in practical engineering.

Small AAAs: Recommendations for Rodent Model Research for the Identification of Novel Therapeutics.

CLINICAL PROBLEM: Most abdominal aortic aneurysms (AAAs) are small with low rupture risk (<1%/y) when diagnosed but slowly expand to ≥55 mm and undergo surgical repair. Patients and clinicians require medications to limit AAA growth and rupture, but drugs effective in animal models have not translated to patients. RECOMMENDATIONS FOR INCREASING TRANSLATION FROM MOUSE MODELS: Use models that simulate human AAA tissue pathology, growth patterns, and rupture; focus on the clinically relevant outcomes of growth and rupture; design studies with the rigor required of human clinical trials; monitor AAA growth using reproducible ultrasound; and perform studies in both males and females. SUMMARY OF STRENGTHS AND WEAKNESSES OF MOUSE MODELS: The aortic adventitial elastase oral ß-aminopropionitrile model has many strengths including simulating human AAA pathology and modeling prolonged aneurysm growth. The Ang II (angiotensin II) model performed less well as it better simulates acute aortic syndrome than AAA. The elastase plus TGFß (transforming growth factor-ß) blocking antibody model displays a high rupture rate, making prolonged monitoring of AAA growth not feasible. The elastase perfusion and calcium chloride models both display limited AAA growth.

Continuous and Controllable Preparation of Sodium Alginate Hydrogel Tubes Guided by the Soft Cap Inspired by the Apical Growth of the Plant.

Hydrogel tubes made of sodium alginate (SA) have potential applications in drug delivery, soft robots, biomimetic blood vessels, tissue stents, and other fields. However, the continuous preparation of hollow SA hydrogel tubes with good stability and size control remains a huge challenge for chemists, material scientists, and medical practitioners. Inspired by the plant apical growth strategy, a new method named soft cap-guided growth was proposed to produce SA hydrogel tubes. Due to the introduction of inert low gravity substances, such as air and heptane, into the extrusion needle in front of calcium chloride solution to form a soft cap, the SA hydrogel tubes with controllable sizes were fabricated rapidly and continuously without using a template through a negative gravitropism mechanism. The SA hydrogel tubes had good tensile strength, high burst pressure, and good cell compatibility. In addition, hydrogel tubes with complex patterns were conveniently created by controlling the motion path of a soft cap, such as a rotating SA bath or magnetic force. Our research provided a simple innovative technique to steer the growth of hydrogel tubes, which made it possible to mass produce hydrogel tubes with controllable sizes and programmable patterns.

Exogenous CaCl2 reduces the oxidative cleavage of carotenoids in shredded carrots by targeting CAMTA4-mediated transcriptional repression of carotenoid degradation pathway.

Carotenoid oxidative cleavage is a significant factor contributing to the color changes of shredded carrots and treatment with calcium chloride (CaCl2, 1% w/v) has been observed to alleviate the whitening symptom and color loss. However, the specific mechanism by which CaCl2 treatment suppresses carotenoid degradation remains unclear. In this study, the effect of CaCl2 and EGTA (calcium ion chelating agent) treatment on carotenoid biosynthesis and degradation in shredded carrots and the mechanism involved was investigated. CaCl2 treatment promoted the expression and activity of carotenoid biosynthetic enzyme (phytoene synthase, PSY), but inhibited the increases of the degradative enzyme activity of carotenoid cleavage dioxygenase (CCD) and down-regulated the corresponding transcripts, thus delayed the degradation of total carotenoid and maintaining higher levels of major carotenoid compounds including ß-carotene, α-carotene, lycopene, and lutein in shredded carrots during storage. However, EGTA treatment promoted the gene expression and enzyme activity of CCD and increased the degradation of carotenoid compounds in shredded carrots during storage. Furthermore, the CaCl2 treatment induced DcCAMTA4, identified as a calcium decoder in shredded carrots, which, in turn, suppressed the expressions of DcCCD1 and DcCCD4 by interacting with their promoters. The transient overexpression of DcCAMTA4 in tobacco leaves led to reduced expression of NtCCD1 and NtCCD4, maintaining a higher content of carotenoids. Thus, CaCl2 alleviated the oxidative cleavage of carotenoids in shredded carrots through the DcCAMTA4-mediated carotenoid degradation pathway.

Synergistic effect of seaweed extract and boric acid and/or calcium chloride on productivity and physico-chemical properties of Valencia orange.

Many citrus species and cultivars are grown successfully in tropical and subtropical countries, as well as in arid and semi-arid regions with low levels of organic matter and low cation exchange, resulting in lower nutrient uptake by the plant. The essential nutrients needed for citrus flowering and fruit set are limited in winter due to a reduction in transpiration rate, negatively effecting vegetative growth, flowering, yield, and fruit quality. The present investigation was carried out to assess the nutritional status, fruit yield parameters, and fruit quality of Valencia orange trees after foliar spraying of seaweed extract (SW) combined with calcium chloride and boric acid and their combinations in the 2020/2021 and 2021/2022 seasons. The treatments were arranged in a split-plot design (three levels spraying seaweed extract × four levels spraying calcium chloride and boric acid and their combinations × four replicates × one tree/replicate). The results indicated that all of the characteristics measured, including leaf chlorophyll, leaf mineral contents, fruit yield parameters, fruit physical properties, and fruit chemical properties, were significantly affected by the foliar spraying of seaweed extract (SW) combined with calcium chloride and boric acid and their combinations. Although all treatments increased the productivity and the physical and chemical properties of Valencia orange fruits compared to the control, a treatment of 10 g/L SW combined with 0.5 g/L boric acid and 1 g/L calcium chloride produced superior results. This ratio of SW, boric acid, and calcium chloride is therefore recommended to enhance productivity and improve the physico-chemical properties of Valencia orange for greater fruit yield.

Corncob-derived biodegradable packaging films: A sustainable solution for raspberry post-harvest preservation.

Plastic food packaging, with its harmful migration of microplastics and nanoplastics into food, presents significant ecological imbalance and human health risks. In this regard, using food and agricultural byproducts as packaging materials reduces environmental and economic concerns and supports their sustainable management. Herein, cellulosic residue from corncob was employed as a renewable source for developing biodegradable packaging films. It was solubilized in ZnCl2 solution, crosslinked with Ca2+ ions, and plasticized with sorbitol to form films and used to improve the shelf-life of raspberries. The optimized film possesses water vapor permeability, tensile strength, and elongation at break of 1.8(4) x10-10 g-1 s-1 Pa-1, 4.7(1) MPa, and 15.4(7)%, respectively. It displays UV-blocking and antioxidant properties and biodegrades within 29 days at 24% soil moisture. It preserves raspberries for 7 and 5 more days at room temperature and refrigeration conditions, respectively, compared to polystyrene film. Overall, more value addition could be envisioned from agricultural residues to minimize post-harvest losses and food waste through biodegradable packaging, which also aids in mitigating plastic perils.

Novel design and performance evaluation of an indirectly forced convection desiccant integrated solar dryer for drying tomatoes in Pakistan.

The process of drying agricultural products for food preservation is a difficult task that requires a significant amount of energy. The increasing cost and depletion of fossil fuels have led to the development of a food dryer that utilizes renewable energy sources. This research paper proposes the design and performance evaluation of an indirectly forced convection desiccant integrated solar dryer (IFCDISD) at the Solar Energy Research Lab at USPCAS-E, NUST Pakistan. Tomatoes were chosen as the test product due to their importance and widespread consumption. The drying process involves slicing the tomatoes and placing them on the IFCDISD rack, where a desiccant called calcium chloride (CaCl2) is integrated into the dryer. The experiments were conducted during both sunshine (SS) hours and Off-sunshine (OSS) hours. The IFCDISD operates using sunlight during SS hours and utilizes the absorbed heat of CaCl2 in OSS hours via a forced DC brushless fan powered by battery charged thro solar panel. The tomatoes were weighed before and after each drying mode, and the moisture removal was calculated. The results show that the dryer efficiency was 50.14 % on day 1, 66 % on day 2, and an overall efficiency of 58.07 %. The moisture content removal was 42.858 % on day 1, 22.9979 % on day 2, and an overall moisture content removal of 58.07 %. Moreover, the payback period is 5.1396 and the carbon mitigation was recorded as 2.0335, and the earned carbon credit was recorded as 11559.6.

Calcium Chloride as a Novel Stabilizer for Foot-and-Mouth Disease Virus and Its Application in the Vaccine Formulation.

The thermal stability of the in-house-developed foot-and-mouth disease (FMD) type O and A viruses was evaluated, and the O Jincheon virus was found to exhibit the lowest thermal stability. To overcome this instability, we proposed a novel stabilizer, calcium chloride. The thermal stability of FMDVs increased up to a CaCl2 concentration of 10 mM, and it had a decreasing trend at >30 mM. The O Jincheon virus showed a significant decrease in the amount of antigen over time at 4 °C. In contrast, the samples treated with CaCl2 showed stable preservation of the virus without significant antigen loss. After the CaCl2-formulated vaccine was administered twice to pigs, the virus neutralization titer reached approximately 1:1000, suggesting that the vaccine could protect pigs against the FMDV challenge. In summary, the O Jincheon virus is difficult to utilize as a vaccine given its low stability during storage after antigen production. However, following its treatment with CaCl2, it can be easily utilized as a vaccine. This study evaluated CaCl2 as a novel stabilizer in FMD vaccines and may contribute to the development of stable vaccine formulations, especially for inherently unstable FMDV strains.

Light-emitting plants development by inoculating of Vibrio campbellii RMT1 on the rhizospheric zone of Aglaonema cochinchinense.

The concept of utilizing light-emitting plants (LEPs) as an alternative to traditional electricity-based lighting has garnered interest. However, challenges persist due to the need for genetic modification or chemical infusion in current LEPs. To address this, researchers have investigated the interaction between plants and luminous bacteria, specifically Vibrio campbellii, which can efficiently be translocated into Aglaonema cochinchinense tissues through the roots to produce LEPs. This study concentrated on examining light intensity and enhancing luminescence by growing plants and spraying them with various media substances. The results indicated that V. campbellii successfully translocated into the plant tissue via the root system and accumulated a high number of bacteria in the stems, approximately 8.46 × 104 CFU/g, resulting in a light-emitting intensity increase of 12.13-fold at 48 h, and then decreased after 30 h. Interestingly, luminescence stimulation by spraying the growth medium managed to induce the highest light emission, reaching 14.84-fold at 48 h, though it had some negative effects on the plant. Conversely, spraying plants with CaCl2 on the leaves prolonged light emission for a longer duration (42 h after spraying) and had a positive effect on plant health, it maintained ion homeostasis and reduced-MDA content. This study highlights the potential of using V. campbellii and CaCl2 spraying for the future development of practical light-emitting plants.

Effect of coadministration of 10 mg/kg calcium chloride and neostigmine on extubation time: A randomized controlled trial.

INTRODUCTION AND OBJECTIVES: Some studies investigating the effect of calcium on neostigmine-induced recovery of neuromuscular blockade have shown that this combination promotes neuromuscular recovery, but does not significantly affect the incidence of postoperative residual curarization and time to extubation. This study aimed to evaluate the effects of 10 mg/kg calcium chloride co-administered with neostigmine on early recovery and time to extubation. PATIENTS AND METHODS: This prospective, randomized, double-blinded, placebo-controlled study included 88 ASA I-II patients aged between 18 and 65 years who were scheduled for elective surgery lasting at least 1 h under general anaesthesia in which 10 mg/kg of calcium chloride or the same volume of normal saline was co-administered with 5 µg/kg of neostigmine at the end of surgery. Time to extubation (time from neostigmine administration to extubation), time from neostigmine administration to TOF ratio (TOFr) 0.9 (neuromuscular recovery), and the incidence of residual neuromuscular blockade (RNMB) and other adverse effects were recorded. RESULTS: Median (Q1, Q3) extubation time was significantly shorter in the calcium group vs. the placebo group (6.5 min [5.52-7.43] vs. 9.78 min [8.35-11]), P < .001. Median neuromuscular recovery time in the calcium group was 5 min vs. 7.1 min in the placebo group, P < .001. Patients in the calcium group had significantly higher TOFr and lower incidence of RNMB at 5 and 10 min vs. the placebo group, and no significant side effects. CONCLUSION: Calcium chloride at a dose of 10 mg/kg co-administered with neostigmine promotes early neuromuscular recovery and reduces time to extubation by about 32%.

[Development, techniques, and utility of experimental animal models of thoracic and abdominal aortic aneurysms]. / Desarrollo, técnicas y utilidad de modelos animales experimentales de aneurismas aórticos torácicos y abdominales.

Aneurysms are clinical entities that can develop and affect human aorta; and although in most cases they have an asymptomatic course, these pathological dilatations can lead to a lethal outcome when rupture occurs, thus the establishment of predictors is crucial for death prevention. Essential events that take place in the vessel wall have been identified and described, such as inflammation, proteolysis, smooth muscle cell apoptosis, angiogenesis, and vascular remodeling. Porcine and ovine models have been useful for the development and evaluation of endovascular devices of the aorta. However, since the worldwide introduction and adoption of these minimally invasive techniques for aneurysm repair, there is lesser availability of diseased aortic tissue for molecular, cellular, and histopathological analysis, therefore over the last three decades it has been proposed various small species models that have allowed the focal induction of these lesions for the study of physiopathological mechanisms and possible useful biomarkers as diagnostic and therapeutic targets. The present review article presents and discusses the animal models available as their applications, characteristics, advantages, and limitations for the development of preclinical studies, and their importance in the comprehension of this pathology in humans.

Los aneurismas son una de las entidades clínicas que pueden desarrollarse y afectar la aorta humana. Aunque en la mayoría de los casos tienen un carácter asintomático, estas dilataciones patológicas pueden resultar letales cuando se presentan con ruptura, por lo que el reconocimiento de factores predictores de esta complicación es crucial para evitar muertes. Fisiopatológicamente se han identificado eventos esenciales que ocurren en la pared del vaso, como inflamación, proteólisis, apoptosis del músculo liso, angiogénesis y remodelación. Las grandes especies como porcinos y ovinos han sido de utilidad para el desarrollo y evaluación del desempeño de dispositivos endovasculares en la aorta, así como la remodelación; con el advenimiento y disposición de estas técnicas mínimamente invasivas para su reparación existe una menor disponibilidad de tejido aórtico para el análisis molecular, celular e histopatológico, por lo que en las últimas tres décadas se han propuesto e introducido distintos modelos que han permitido, mediante la inducción focal de estas lesiones, el estudio de los mecanismos fisiopatológicos y posibles biomarcadores de utilidad como dianas diagnósticas y terapéuticas. El presente artículo de revisión aborda tipos de modelos animales disponibles, así como sus aplicaciones, consideraciones, ventajas y limitaciones para el desarrollo de estudios preclínicos y su importancia en el entendimiento de esta patología en la especie humana.

The effect of three additives on properties of mineral trioxide aggregate cements: a systematic review and meta-analysis of in vitro studies.

BACKGROUND: Several efforts have been made to improve mechanical and biological properties of calcium silicate-based cements through changes in chemical composition of the materials. This study aimed to investigate the physical (including setting time and compressive strength) and chemical (including calcium ion release, pH level) properties as well as changes in cytotoxicity of mineral trioxide aggregate (MTA) after the addition of 3 substances including CaCl2, Na2HPO4, and propylene glycol (PG). METHODS: The systematic review was conducted in accordance with Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA). Electronic searches were performed on PubMed, Embase, and Scopus databases, spanning from 1993 to October 2023 in addition to manual searches. Relevant laboratory studies were included. The quality of the included studies was assessed using modified ARRIVE criteria. Meta-analyses were performed by RevMan statistical software. RESULTS: From the total of 267 studies, 24 articles were included in this review. The results of the meta-analysis indicated that addition of PG increased final setting time and Ca2+ ion release. Addition of Na2HPO4 did not change pH and cytotoxicity but reduced the final setting time. Incorporation of 5% CaCl2 reduced the setting time but did not alter the cytotoxicity of the cement. However, addition of 10% CaCl2 reduced cell viability, setting time, and compressive strength. CONCLUSION: Inclusion of 2.5% wt. Na2HPO4 and 5% CaCl2 in MTA can be advisable for enhancing the physical, chemical, and cytotoxic characteristics of the admixture. Conversely, caution is advised against incorporating elevated concentrations of PG due to its retarding effect. TRIAL REGISTRATION: PROSPERO registration number: CRD42021253707.

Synthesis, characterization, and application of honey stabilized inulin nanoparticles as colon targeting drug delivery carrier.

Inulin (INU) is a versatile natural polysaccharide primarily derived from chicory roots. INU possesses the unique quality of evading digestion or fermentation in the early stages of the human digestive tract, instead reaching the lower colon directly. Exploiting on this distinctive attribute, INU finds application in the creation of targeted carrier systems for delivering drugs tailored to colon-related diseases. This study presents a novel method for synthesizing highly stable and non-aggregatory inulin nanoparticles (INU NPs) by ionotropic gelation method, using calcium chloride as crosslinker and natural honey as a stabilizing agent. Different formulation and process parameters were optimized for the synthesis of monodispersed INU NPs. These INU NPs efficiently encapsulated a hydrophilic drug irinotecan hydrochloride trihydrate (IHT) and drug loaded formulation (IINPs) demonstrated excellent colloidal and storage stabilities. Notably, these IINPs exhibited pH-dependent drug release, suggesting potential for colon-specific drug delivery. Anticancer activity of the NPs was found significantly higher in comparison to IHT through cytotoxicity and apoptosis studies against human colorectal carcinoma cells. Overall, this study revealed that the INU NPs synthesized by ionotropic gelation will be an efficient nanocarrier system for colon-targeted drug delivery due to their exceptional biocompatibility and stability in stomach and upper intestinal conditions.

Effect of magnetic field mediated CaCl2 on the edible quality of low-sodium minced pork gels.

Magnetic field combined with calcium chloride (CaCl2,) treatment is a highly promising technique for reducing sodium chloride (NaCl) in meat. Therefore, this paper investigated the effect of reducing NaCl addition (0-10%) by CaCl2 in combination with a magnetic field (3.8 mT) on the edible quality of low-salt pork mince. It is desired to drive the application of magnetic field and CaCl2 in low-sodium meat processing in this way. Results showed that the cooking yield, color, hardness, elasticity, mouthfeel, apparent texture, and orderliness of protein conformation of all minced pork were improved as compared to the control group, while the electron nose response values of their volatile sulfides and nitrogen oxides were decreased. In particular, the best edible quality and perceived salty intensity of minced pork gel was obtained by using CaCl2 in place of 5% NaCl under magnetic field mediation. In addition, energy dispersive X-ray spectroscopy scans showed that the reduced NaCl treatment by magnetic field combined with CaCl2 could increase the signal intensity of sodium in minced pork matrices to some extent. Magnetic field-mediated substitution of NaCl for CaCl2 treatment was also found to be favorable for inducing the transition of the protein secondary structure from an irregularly coiled to a ß-folded structure (demonstrated by infrared spectroscopy). In short, magnetic fields combined with CaCl2 instead of NaCl was a highly promising method of producing low-NaCl meats.

Animal Models, Pathogenesis, and Potential Treatment of Thoracic Aortic Aneurysm.

Thoracic aortic aneurysm (TAA) has a prevalence of 0.16-0.34% and an incidence of 7.6 per 100,000 person-years, accounting for 1-2% of all deaths in Western countries. Currently, no effective pharmacological therapies have been identified to slow TAA development and prevent TAA rupture. Large TAAs are treated with open surgical repair and less invasive thoracic endovascular aortic repair, both of which have high perioperative mortality risk. Therefore, there is an urgent medical need to identify the cellular and molecular mechanisms underlying TAA development and rupture to develop new therapies. In this review, we summarize animal TAA models including recent developments in porcine and zebrafish models: porcine models can assess new therapeutic devices or intervention strategies in a large mammal and zebrafish models can employ large-scale small-molecule suppressor screening in microwells. The second part of the review covers current views of TAA pathogenesis, derived from recent studies using these animal models, with a focus on the roles of the transforming growth factor-beta (TGFß) pathway and the vascular smooth muscle cell (VSMC)-elastin-contractile unit. The last part discusses TAA treatment options as they emerge from recent preclinical studies.