A highly sensitive electrochemical sensor based on poly(3-aminobenzoic acid)/graphene oxide-gold nanoparticles modified screen printed carbon electrode for paraquat detection.

Herein, a modified screen printed carbon electrode (SPCE) based on a composite material, graphene oxide-gold nanoparticles (GO-AuNPs), and poly(3-aminobenzoic acid)(P3ABA) for the detection of paraquat (PQ) is introduced. The modified electrode was fabricated by drop casting of the GO-AuNPs, followed by electropolymerization of 3-aminobenzoic acid to achieve SPCE/GO-AuNPs/P3ABA. The morphology and microstructural characteristics of the modified electrodes were revealed by scanning electron microscopy (SEM) for each step of modification. The composite GO-AuNPs can provide high surface area and enhance electroconductivity of the electrode. In addition, the presence of negatively charged P3ABA notably improved PQ adsorption and electron transfer rate, which stimulate redox reaction on the modified electrode, thus improving the sensitivity of PQ analysis. The SPCE/GO-AuNPs/P3ABA offered a wide linear range of PQ determination (10-9-10-4 mol/L) and low limit of detection (LOD) of 0.45 × 10-9 mol/L or 0.116 µg/L, which is far below international safety regulations. The modified electrode showed minimum interference effect with percent recovery ranging from 96.5% to 116.1% after addition of other herbicides, pesticides, metal ions, and additives. The stability of the SPCE/GO-AuNPs/P3ABA was evaluated, and the results indicated negligible changes in the detection signal over 9 weeks. Moreover, this modified electrode was successfully implemented for PQ analysis in both natural and tapped water with high accuracy.

Nano-Enhanced Graphite/Phase Change Material/Graphene Composite for Sustainable and Efficient Passive Thermal Management.

Passive battery thermal management systems (BTMSs) are critical for mitigation of battery thermal runaway (TR). Phase change materials (PCMs) have shown promise for mitigating transient thermal challenges. Fluid leakage and low effective thermal conductivity limit PCM adoption. Furthermore, the thermal capacitance of PCMs diminishes as their latent load is exhausted, creating an unsustainable cooling effect that is transitory. Here, an expanded graphite/PCM/graphene composite that solves these challenges is proposed. The expanded graphite/PCM phase change composite eliminates leakage and increases effective thermal conductivity while the graphene coating enables radiative cooling for PCM regeneration. The composite demonstrates excellent thermal performance in a real BTMS and shows a 26% decrease in temperature when compared to conventional BTMS materials. The composite exhibits thermal control performance comparable with active cooling, resulting in reduced cost and increased simplicity. In addition to BTMSs, this material is anticipated to have application in a plethora of engineered systems requiring stringent thermal management.

Self-Propagating Fabrication of a 3D Graphite@rGO Film Anode for High-performance Potassium-Ion Batteries.

Graphite, with abundant resources and low cost, is regarded as a promising anode material for potassium-ion batteries (PIBs). However, because of the large size of potassium ions, the intercalation/deintercalation of potassium between the interlayers of graphite results in its huge volume expansion, leading to poor cycling stability and rate performance. Herein, a self-propagating reduction strategy is adopted to fabricate a flexible, self-supporting 3D porous graphite@reduced graphene oxide (3D-G@rGO) composite film for PIBs. The 3D porous network can not only effectively mitigate the volume expansion in graphite but also provide numerous active sites for potassium storage as well as allow for electrolyte penetration and rapid ion migration. Therefore, compared to the pristine graphite anode, the flexible 3D-G@rGO film electrode exhibits greatly improved K-storage performance with a reversible capacity of 452.8 mAh g-1 at 0.1 C and a capacity retention rate of 80.4% after 100 cycles. It also presents excellent rate capability with a high specific capacity of 139.1 and 94.2 mAh g-1 maintained at 2 and 5 C, respectively. The proposed self-propagating reduction strategy to construct a three-dimensional self-supporting structure is a viable route to improve the structural stability and potassium storage performance of graphite anodes.

Fabrication of granular three-dimensional graphene oxide/UiO-66 adsorbent for high uranium adsorption: Density functional theory and fixed bed column studies.

This study presents a thorough investigation of the novel application of graphene oxide (GO) modified with melamine formaldehyde to fabricate granular three-dimensional GO (3D-GO), followed by the introduction of UiO-66 doping (3D-GO/U) for high uranium (U) adsorption. The U(VI) adsorption isotherms revealed that 3D-GO/U-10 with 10 % UiO-66 incorporation exhibited an impressive adsorption capacity of 375.5 mg g-1 and remained high U(VI) sorption performance in wide pH range. The introduction of UiO-66 to 3D-GO (3D-GO/U-10) led to the deagglomeration of the UiO-66 particles. The in situ surface-enhanced-Raman-spectroscopy-analysis and density-functional-theory simulations showed the symmetric metal center site Zr-O2 on UiO-66 was discovered to exhibit the highest adsorption energy (-3.21 eV) for U(VI) species due to the electrons transfer from the oxygen atom to U(VI) drives the covalent bonding between the symmetric metal center sites Zr-O2 and U(VI) on 3D-GO/U-10. The 3D-GO/U-10 was regenerated using a 0.1 M Na2CO3/0.01 M H2O2 solution and achieved up to 89.7 % U(VI) removal in the 5th cycle. The continuous flow column experiments results revealed 3D-GO/U-10 can regenerate and maintain a U(VI) removal capacity of ∼76 % for up to 4 cycles column experiments. Therefore, 3D-GO/U-10 exhibits great potential for removing U(VI) from water bodies.

Synthesis and analysis of multifunctional graphene oxide/Ag2O-PVA/chitosan hybrid polymeric composite for wound healing applications.

The requirement for accurate treatments for skin diseases and wounds, generated a rising interest towards multifunctional polymer composites, that are capable of mimicking the natural compositions in human body. Also, electroactive composite films disseminate endogenous electrical stimulations that encourage cell migration and its proliferation at wound site, proposing greater opportunities in upgrading the conventional wound patches. In this work, the composite film made of graphene oxide, Ag2O, PVA and chitosan were developed for wound healing applications, by the solution casting method. The even dispersibility of nanofiller in polymeric matrix was validated from the physicochemical analyses. The increment in roughness of the composite film surface was noted from AFM images. The thermal stability and porous nature of the polymer composite were also verified. A conductivity value of 0.16 × 10-4 Scm-1 was obtained for the film. From MTT assay, it was noted that the films were non-cytotoxic and supported cell adhesion along with cell proliferation of macrophage (RAW 264.7) cells. Moreover, the composite film also demonstrated non-hemolytic activity of <2 %, as well as excellent antibacterial activity towards E. coli and S. aureus. Thus, the obtained results validated that the prepared composite film could be chosen as an innovative candidate for developing state-of-the-art wound dressings.

Graphene-Infused Sustainable Rubber-Based Triboelectric Nanogenerator For Real-Time Human Motion Monitoring.

Triboelectric nanogenerators (TENG) are promising alternatives for clean energy harvesting. However, the material utilization in the development of TENG relies majorly on polymers derived from non-renewable resources. Therefore, minimizing the carbon footprint associated with such TENG development demands a shift toward usage of sustainable materials. This study pioneers using natural rubber (NR) as a sustainable alternative in TENG development. Infusing graphene in NR, its dielectric constant and tribonegativity are optimized, yielding a remarkable enhancement. The optimized sample exhibits a dielectric constant of 411 (at 103 Hz) and a contact potential difference (CPD) value of 1.85 V. In contrast, the pristine NR sample showed values of 6 and 3.06 V for the dielectric constant and CPD. Simulation and experimental studies fine-tune the TENG's performance, demonstrating excellent agreement between theoretical predictions and practical studies. Sensors developed via stencil printing technique possess a remarkably low layer thickness of 270 µm, and boast a power density of 420 mW m-2, a staggering 250% increase over conventional NR. Moreover, the material is pressure sensitive, enabling precise real-time human motion detection, including finger contact, finger bending, neck bending, and arm bending. This versatile sensor offers wireless monitoring, empowering healthcare monitoring based on the Internet of Things.

Layered Heterostructure of Graphene and TiO2 as a Highly Sensitive and Stable Photoassisted NO2 Sensor.

As an atomically thin electric conductor with a low density of highly mobile charge carriers, graphene is a suitable transducer for molecular adsorption. In this study, we demonstrate that the adsorption properties can be significantly enhanced with a laser-deposited TiO2 nanolayer on top of single-layer CVD graphene, whereas the effective charge transfer between the TiO2-adsorbed gas molecules and graphene is retained through the interface. The formation of such a heterostructure with optimally a monolayer thick oxide combined with ultraviolet irradiation (wavelength 365 nm, intensity <1 mW/mm2) dramatically enhances the gas-sensing properties. It provides an outstanding sensitivity for detecting NO2 in the range of a few ppb to a few hundred ppb-s in air, with response times below 30 s at room temperature. The effect of visible light (436 and 546 nm) was much weaker, indicating that the excitations due to light absorption in TiO2 play an essential role, while the characteristics of gas responses imply the involvement of both photoinduced adsorption and desorption. The sensing mechanism was confirmed by theoretical simulations on a NO2@Ti8O16C50 complex under periodic boundary conditions. The proposed sensor structure has significant additional merits, such as relative insensitivity to other polluting gases (CO, SO2, NH3) and air humidity, as well as long-term stability (>2 years) in ambient air. The results pave the way for an emerging class of gas sensor structures based on stacked 2D materials incorporating highly charge-sensitive transducer and selective receptor layers.

Development of tungsten trioxide nano-flakes intercalated on tannic acid-functionalized reduced graphene oxide for flexible acebutolol sensors.

Acebutolol (ACE) is commonly used to treat hypertension and high blood pressure. Large doses of ACE can have adverse effects with potentially life-threatening consequences. It is, therefore, essential to develop a simple, low-cost, reliable, and reproducible device for detecting ACE in biofluids. This study explores the potential of unique two-dimensional nano-flakes, such as tungsten trioxide (WO3). Graphene oxide (GO) typically exhibits lower electrical conductivity than pristine graphene due to the presence of oxygen-containing functional groups that interfere with the π-conjugated structure. Functionalizing GO with tannic acid (TA) can partially reinstate the π-conjugation and limit the amount of oxygen, resulting in enhanced electrical conductivity. Ultrasonic techniques were utilized to create WO3 NFs@TA-rGO, and a range of spectroscopic and microscopic methods were applied to examine the formation of the resulting WO3 NFs@TA-rGO nanocomposites. Under optimal conditions, modified sensors resulted in lower limits of detection (0.0055 µM) and good sensitivity (0.40 µA µM-1 cm-2). They also exhibited a broad linear range spanning from 0.009 to 568.6 µM. Fabricated sensors have significant anti-interference properties with high specificity and excellent storage stability (RSD = 4.3 %), reproducibility (RSD = 3.9 %), and repeatability (RSD = 3.3 %). Ultimately, the sensor's efficacy was confirmed through the successful detection of ACE in biological samples (with recoveries ranging from 99.1 to 99.6 %). Lastly, this study highlights the substantial potential of ACE detection and extends its applications in biomedical diagnostics and pharmaceutical research.

Sensitive extraction of seven pesticide residues from environmental water with magnetic graphene oxide-based covalent organic framework.

The use of pesticides has increased with the development of agriculture. However, due to the trace content and the matrix's inherent complexity in environmental water, development of rapid and sensitive detection method present significant challenges in the analysis of pesticide residues. The study synthesized magnetic graphene oxide (MGO) by combining superparamagnetic nanoparticles with the easy modification of graphene oxide (GO). Covalent organic frameworks (COFs) were then modified to have a large specific surface area. Finally, magnetic graphene oxide-based covalent organic frameworks, namely MGO-COFs, were obtained with a spherical structure and used as magnetic solid-phase extraction materials, which was successfully used to determine the seven pesticide residues in environmental samples in conjunction with high performance liquid chromatography. The method has a wide linear range for the tested pesticides, with satisfactory correlation coefficients (R ≥ 0.099) and low detection limits (0.3-1.21 µg L-1). The correlation coefficients for all seven pesticides were high (R2 ≥ 0.9996). The spiked recoveries, exhibiting a range of 91.3 to 109 %, demonstrated that the developed MGO-COF-MSPE-HPLC-UV method is simple, efficient, and suitable for the analysis and detection of seven pesticide residues in environmental water.

Maltodextrin-modified graphene oxide composite membrane applied to the enantioseparation of amino acids.

The separation of enantiomers using chiral membranes has garnered much research interest. In this study, the enantioseparation of amino acids using chiral membranes, namely graphene oxide-ethylenediamine-maltodextrin (GO-EDA-MD) and GO-EDA-hydroxypropyl-MD (GO-EDA-HP-MD), was evaluated. HP-MD and MD were investigated as chiral selectors due to their inherent chirality. Various characterization techniques, including atomic force microscopy, Fourier transform infrared spectrometry, field emission scanning electron microscopy, water contact angle analysis, tensile properties, and thermal gravimetric analysis were employed to analyze the membrane structures. The evaluation of enantioseparation performance was conducted by employing tryptophan, phenylalanine, and tyrosine enantiomers. Optimal conditions for enantiomer separation were achived using a GO-EDA-HP-MD chiral composite (1.75 wt%), a feed concentration of 10 mg/L for each enantiomer, a separation time of 15 min, and a membrane effective surface area of 1.0 cm2. Also, the bovine serum albumin rejection was 90.0 %, and the water flux reached 37.1 L m-2 h-1. The highest enantiomeric excess (ee.%) values were 46.33 %, 76.97 %, and 73.04 % for tryptophan, phenylalanine, and tyrosine, respectively. The impact of voltage on ee.% and substance flux was also explored. This membrane was able to separate enantiomers successfully.

Wide-temperature-range pressure sensing by an aramid nanofibers/reduced graphene oxide flakes composite aerogel.

Aerogel-based conductive materials have emerged as a major candidate for piezoresistive pressure sensors due to their excellent mechanical and electrical performance besides light-weighted and low-cost characteristics, showing great potential for applications in electronic skins, biomedicine, robot controlling and intelligent recognition. However, it remains a grand challenge for these piezoresistive sensors to achieve a high sensitivity across a wide working temperature range. Herein, we report a highly flexible and ultra-light composite aerogel consisting of aramid nanofibers (ANFs) and reduced graphene oxide flakes (rGOFs) for application as a high-performance pressure sensing material in a wide temperature range. By controlling the orientations of pores in the composite framework, the aerogel promotes pressure transfer by aligning its conductive channels. As a result, the ANFs/rGOFs aerogel-based piezoresistive sensor exhibits a high sensitivity of up to 7.10 kPa-1, an excellent stability over 12,000 cycles, and an ultra-wide working temperature range from -196 to 200 °C. It is anticipated that the ANFs/rGOFs composite aerogel can be used as reliable sensing materials in extreme environments.

An Investigation into the Influence of Graphene Content on Achieving a High-Performance TiO2-Graphene Nanocomposite Supercapacitor.

This study presents the synthesis of TiO2-graphene nanocomposites with varying mass ratios of graphene (2.5, 5, 10, 20 wt. %) using a facile and cost-effective hydrothermal approach. By integrating TiO2 nanoparticles with graphene, a nanomaterial characterized by a two-dimensional structure, unique electrical conductivity and high specific surface area, the resulting hybrid material shows promise for application in supercapacitors. The nanocomposite specimens were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, Raman microscopy, field-emission scanning electron microscopy (FESEM), and transmission electron microscopy (TEM). Additionally, supercapacitive properties were investigated using a three-electrode setup by cyclic voltammetry (CV), galvanostatic charge-discharge (GCD) and electrochemical impedance spectroscopy (EIS) tests. Notably, the TiO2-20 wt. % rGO nanocomposite exhibited the highest specific capacitance of 624 F/g at 2 A/g, showcasing superior electrochemical performance. This specimen indicated a high rate capability and cyclic stability (93 % retention after 2000 cycles). Its remarkable energy density and power density of this sample designate it as a strong contender for practical supercapacitor applications.

Graphene Terahertz Devices for Sensing and Communication.

Graphene-based terahertz (THz) devices have emerged as promising platforms for a variety of applications, leveraging graphene's unique optoelectronic properties. This review explores recent advancements in utilizing graphene in THz technology, focusing on two main aspects: THz molecular sensing and THz wave modulation. In molecular sensing, the environment-sensitive THz transmission and emission properties of graphene are utilized for enabling molecular adsorption detection and biomolecular sensing. This capability holds significant potential, from the detection of pesticides to DNA at high sensitivity and selectivity. In THz wave modulation, crucial for next-generation wireless communication systems, graphene demonstrates remarkable potential in absorption modulation when gated. Novel device structures, spectroscopic systems, and metasurface architectures have enabled enhanced absorption and wave modulation. Furthermore, techniques such as spatial phase modulation and polarization manipulation have been explored. From sensing to communication, graphene-based THz devices present a wide array of opportunities for future research and development. Finally, advancements in sensing techniques not only enhance biomolecular analysis but also contribute to optimizing graphene's properties for communication by enabling efficient modulation of electromagnetic waves. Conversely, developments in communication strategies inform and enhance sensing capabilities, establishing a mutually beneficial relationship.

Cellulose Nanofiber-Based Nanocomposite Films with Efficient Electromagnetic Interference Shielding and Fire-Resistant Performance.

Cellulose nanofiber (CNF) has been widely used as a flexible and lightweight polymer matrix for electromagnetic shielding and thermally conductive composite films because of its excellent mechanical strength, environmental performance, and low cost. However, the lack of flame retardancy seriously hinders its further application. Herein, renewable and biomass-sourced l-arginine (AR) was used to surface-modify ammonium polyphosphate (APP) and an environmentally friendly biobased flame retardant was synthesized by the coordination of zinc sulfate heptahydrate (ZnSO4·7H2O), which was named AAZ. AAZ was deposited on the surface of CNF by electrostatic adsorption and Zn2+ complexation. The biobased compatibilizer Triton X-100 was employed to assist the exfoliation of graphene nanoplatelets (GNPs) and their dispersion in the CNF matrix. Due to the formation of a dense lamellar layer resembling a shell structure, the CNF/GNPs composite films with a tensile strength of 52 MPa were obtained via vacuum-assisted filtration. Because the phosphorus-containing group produces a protective layer of PxOy compound and promotes the formation of a carbon layer by CNF and the combustion releases ammonia gas, the fire-resistant performance of the composite films was greatly improved. Compared with the pure CNF film, the composite film exhibits 33% reduction in PHRR value and 40% reduction in THR. In addition, the CNF/GNPs composite film with 20 wt % GNPs possessed high conductivity (2079.2 S/m) and electromagnetic interference (EMI) shielding effectiveness (37 dB). The ultrathin CNF/GNPs composite films have excellent potential for use as efficient flame retardant and EMI shielding materials.

Interactions of graphene oxide with the microbial community of biologically active filters from a water treatment plant.

With widespread occurrence and increasing concern of emerging contaminants (CECs) in source water, biologically active filters (BAF) have been gaining acceptance in water treatment. Both BAFs and graphene oxide (GO) have been shown to be effective in treating CECs. However, studies to date have not addressed interactions between GO and microbial communities in water treatment processes such as BAFs. Therefore, in the present study, we investigated the effect of GO on the properties and microbial growth rate in a BAF system. Synthesized GO was characterized with a number of tools, including scanning electron microscopy (SEM), energy dispersive x-ray spectroscopy (EDX), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and Raman spectrometry. GO exhibited the characteristic surface functional groups (i.e., C-OH, C=O, C-O-C, and COOH), crystalline structure, and sheet-like morphology. To address the potential toxicity of GO on the microbial community, reactive oxygen species (ROS) generation was measured using nitro blue tetrazolium (NBT) assay. Results revealed that during the exponential growth phase, ROS generation was not observed in the presence of GO compared to the control batch. In fact, the adenosine triphosphate (ATP) concentrations increased in the presence of GO (25 µg/L - 1000 µg/L) compared to the control without GO. The growth rate in systems with GO exceeded the control by 20 % to 46 %. SEM images showed that GO sheets can form an effective scaffold to promote bacterial adhesion, proliferation, and biofilm formation, demonstrating its biocompatibility. Next-generation sequencing (Illumina MiSeq) was used to characterize the BAF microbial community, and high-throughput sequencing analysis confirmed the greater richness and more diverse microbial communities compared to systems without GO. This study is the first to report the effect of GO on the microbial community of BAF from a water treatment plant, which provides new insights into the potential of utilizing a bio-optimized BAF for advanced and sustainable water treatment or reuse strategies.

Bacteria-Derived Cellulose Membranes Modified with Graphene Oxide-Silver Nanoparticles for Accelerating Wound Healing.

This study reports on the modification of bacterial cellulose (BC) membranes produced by static fermentation of Komagataeibacter xylinus bacterial strains with graphene oxide-silver nanoparticles (GO-Ag) to yield skin wound dressings with improved antibacterial properties. The GO-Ag sheets were synthesized through chemical reduction with sodium citrate and were utilized to functionalize the BC membranes (BC/GO-Ag). The BC/GO-Ag composites were characterized to determine their surface charge, morphology, exudate absorption, antimicrobial activity, and cytotoxicity by using fibroblast cells. The antimicrobial activity of the wound dressings was assessed against Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa. The results indicate that the BC/GO-Ag dressings can inhibit ∼70% of E. coli cells. Our findings also revealed that the porous BC/GO-Ag antimicrobial dressings can efficiently retain 94% of exudate absorption after exposure to simulated body fluid (SBF) for 24 h. These results suggest that the dressings could absorb excess exudate from the wound during clinical application, maintaining adequate moisture, and promoting the proliferation of epithelial cells. The BC/GO-Ag hybrid materials exhibited excellent mechanical flexibility and low cytotoxicity to fibroblast cells, making excellent wound dressings able to control bacterial infectious processes and promote the fast healing of dermal lesions.

Electrochemical based quantification of bacterial growth in media using square wave voltammetry and low cost screen printed electrodes.

A novel method for determining the yield of bacterial growth using square wave voltammetry and screen printed electrodes is described here. This procedure was shown to be a reliable and accurate way to quickly determine the level of bacterial growth within culturing media and these results suggest that the combination of such sensors and the application of square wave voltammetry is suitable for applications such as within a bioreactor where the rapid determination of bacterial growth may be necessary.

Sensing of volatile pollutants on reduced graphene oxide-polypyrrole composite: DFT investigation.

Air pollutants generated from volatile toxic chemicals pose significant public health concerns. Density functional theory (DFT) computations were used in this research to explore the efficiency and mechanism of harmful gas sensing over the reduced graphene oxide-polypyrrole (rGO-PPy) composite. Volatile molecule sensing was investigated for the NH3, H2CO, CH3OH, and C2H5OH gas molecules over three PPy orientations on the rGO substrate. Results showed that PPy orientation over rGO plays a crucial role in the sensing efficiency of the investigated gas molecules. The rGO-PPy composite, with PPy in a vertical orientation, demonstrated higher stability and enhanced sensing than other orientations. The results indicate that the strong hydrogen bonding of NH3 and CH3OH with both PPy and rGO significantly enhanced the sensing of these gas molecules on rGO by influencing the charge transfer with adsorption energy values of - 0.84 and - 0.92 eV, respectively. The lack of a direct hydrogen bonding with rGO and the weak hydrogen bonding with PPy caused a weak adsorption of H2CO and C2H5OH over rGO as indicated by the adsorption energy values of - 0.60 and - 0.78 eV, respectively. Selectivity analysis for the NH3 and C2H5OH gas molecules showed that NH3 can maintain hydrogen bonding with PPy in the presence of C2H5OH while C2H5OH cannot sustain this interaction. This study highlights the importance of the structural and electronic properties of the rGO-PPy composite in volatile pollutant sensing, providing insights for designing high-performance gas sensors.

Generating luminescent Graphene quantum Dots from Tryptophan: Fluorosensors for hydrogen peroxide in cancer cells.

Herein, we report a single step synthesis of highly fluorescent Graphene Quantum Dots (GQDs) using tryptophan and glycerol as precursors via pyrolysis. The morphological and functional characterization of the prepared GQDs was performed using PXRD, FTIR, TEM, XPS and zeta potential measurements. The prepared GQDs found their practical application in ultrasensitive detection of an emerging potential cancer biomarker, H2O2, by exploiting the fluorescence quenching behaviour of H2O2. To evaluate the detection sensitivity, a series of various concentrations of H2O2 was spiked to biomatrices like, serum and MCF-7 (human breast cancer cell line) cell lysate medium. A remarkably low limit of detection (LOD) was found in serum medium (139.5 pM) which further improved in MCF-7 cell lysate medium (LOD 61.43 pM). Moreover, the sensing capacity of the GQDs was further validated in presence of various physiological variables such as glucose, cholesterol, insulin and nitrite. Sensing assay was also carried out in HaCaT (human keratinocyte cell line) cell lysate medium to compare the performance of our prepared sensor but the non-linearity of the F0/F versus H2O2 concentration plot pointed towards the conduciveness of the MCF-7 cell lysate medium for sensitive detection of H2O2.The mechanism behind the sensing was also explored using spectroscopic methods.

Strong Electron-Vibration Signals in Weakly Coupled Molecular Junctions: Activation of Spin-Crossover.

Manipulating individual molecular spin states with electronic current has the potential to revolutionize quantum information devices. However, it is still unclear how a current can cause a spin transition in single-molecule devices. Here, we propose a spin-crossover (SCO) mechanism induced by electron-phonon coupling in an iron(II) phthalocyanine molecule situated on a graphene-decoupled Ir(111) substrate. We performed simulations of both elastic and inelastic electron tunneling spectroscopy (IETS), which reveal current-induced Fe-N vibrations and an underestimation of established electron-vibration signals. Going beyond standard perturbation theory, we examined molecules in various charge and spin states using the Franck-Condon framework. The increased probability of spin switching suggests that notable IETS signals indicate SCO triggered by the inelastic vibrational excitation associated with Fe-N stretching.