Evaluation of Surface Roughness of Acrylic Denture Bases Polished Using Algishine, a Novel Polishing Material: An In Vitro Study.

Introduction Surface roughness (Ra) significantly impacts the aesthetic and functional qualities of dental prosthetics. Traditional polishing involves pumice, a material routinely used in dental practice. This study introduces Algishine as a potential cost-effective eco-friendly alternative. Materials and methods A 3D design software (Geomagic) created a Standard Tesselation Language (STL) file of 10 mm x 10 mm x 2 mm. 30 STL file outputs were generated. The output was milled in wax. This was then flasked and processed. 30 acrylic resin specimens were fabricated and divided into two groups. Group A was polished using traditional pumice, and Group B was polished using Algishine. The Ra of each sample was measured using surface profilometry, with three readings per sample averaged for each group. Results Kruskal-Wallis test was performed to compare the two groups with the pre-testing samples, which showed p<0.05; indicating that there was a significant difference between the two groups. The average Ra value for unpolished acrylic was 7.105, while the specimens polished with pumice showed an Ra value of 2.218; specimens polished with novel material Algishine showed an Ra value of 1.743. This illustrates that Algishine achieves surface smoothness significantly superior to commonly used polishing agent and pumice. Discussion The results of our study demonstrate that Algishine, a novel polishing material derived from recycled alginate, effectively reduces the Ra of acrylic resin. This finding has significant implications, both clinically and environmentally. The primary clinical benefit of a smoother acrylic resin surface is the enhanced aesthetic appearance and increased patient comfort. A polished surface reduces plaque accumulation, thereby decreasing the risk of oral infections and improving the longevity of the dental prosthesis. The results show that Algishine achieves surface smoothness comparable to or better than pumice indicating that it can maintain, if not enhance, these clinical outcomes. Dental professionals can confidently use Algishine, knowing it meets the high standards required for patient care. Conclusion Algishine effectively reduces the Ra of acrylic resin, suggesting it is a viable, eco-friendly alternative to traditional pumice for dental polishing procedures. This indicates potential benefits in maintaining clinical outcomes while promoting environmental sustainability.

Evaluation of the Long-Term Success and Patient-Related Outcomes of Zygomatic Implants in Atrophic Maxillary Ridges.

Introduction Zygomatic implants (ZIs) have emerged as a promising option for rehabilitating completely edentulous patients with severe maxillary atrophy. These implants anchor into the zygomatic bone, bypassing the need for extensive grafting procedures. Success rates in dental and craniofacial implant surgeries can be influenced by several surgical factors, including suture techniques, flap design, and treatment planning. The research aimed to present the clinical outcomes and complications in individuals with severely resorbed maxillae who underwent prosthodontic rehabilitation using the Quad Zygoma Protocol (QZP) and the Anatomy-Guided Approach (AGA), focusing on long-term assessment. Material and methods Data for this retrospective study were extracted from the institution's patient database, involving a meticulous review of patient records. This comprehensive examination encompassed demographic data, preoperative assessments, details of surgical procedures, postoperative complications, and subsequent follow-up evaluations. Patients with severe maxillary bone deficiencies resulting in complete edentulism, due to inadequate bone quality and quantity in both anterior and posterior regions, were selected for inclusion. Exclusion criteria were applied to individuals with incomplete records or insufficient follow-up data, as well as those who underwent alternative treatment modalities or presented with comorbidities potentially impacting implant outcomes. The selected patients underwent treatment utilizing the QZP, with each participant subjected to a minimum three-year follow-up period. The implant survival rate, prosthetic success, complications, and Oral Health-Related Quality of Life using the OHIP-14 questionnaire were assessed. Results At the end of the follow-up period involving 12 patients (eight men, four women) with 43 ZIs - 37 from Neodent, four from Nobel Biocare, and two from Norris - with a mean duration of 4.3 years (range: 1.2-5.4), the overall success rate stood at 99.08%, with only 1 out of 42 implants failing. All patients received immediate loading with an acrylic prosthesis, proving effective in 98.2% of cases. The most common issues observed were localized soft tissue inflammation (35.7%) and sinus inflammation (12.5%), occurring after mean follow-up periods of 1.2 and 3.5 years, respectively. In 12 patients, the mean score of the OHIP-14 questionnaire was 1.6 ± 2.6, with a follow-up period of 5 ± 0.6 years. Conclusion The QZP has consistently demonstrated excellent long-term success in restoring severely reduced maxillary structures. An immediate loading approach could aid in stabilizing ZIs through cross-arch support.

In Vitro Analysis of the Accuracy of the Use of Waste Zirconia Dust Compared With Optical Scanning Spray on Implant Abutment Models in Extraoral Scanning Protocol.

Introduction The evolution of computer-aided design/computer-aided manufacturing (CAD/CAM) systems has heightened the significance of digital models in dentistry, particularly for fabricating prostheses like inlays, crowns, and bridges. While digital dentistry offers enhanced speed and precision, the initial investment in intraoral scanners may pose a barrier for some clinicians. Extraoral or lab scanners, however, offer a viable alternative, reducing laboratory time and providing accurate prostheses fit, though challenges such as reflective surfaces and availability of scanning sprays persist, impacting scanning quality and operator technique. Optical scanning using laboratory scanners is a routine practice in today's age of digital dentistry. Often these require powder opacification to record fine details. There are numbered studies on the accuracy of scanning sprays. Materials and methods Ten casts, poured with type 4 dental stone (Elite Rock, Zhermack, Italy) with single implants, were used for the purpose of this study. Each cast was scanned by two different operators, using both mediums. It was scanned using an extraoral scanner (E4, 3Shape, Copenhagen, Denmark). Operator A used easy scan (Alphadent, Korea), followed by zirconia dust (Upcera, Guangdong, China), whereas operator B used zirconia dust first. Digital models within each group were superimposed individually to measure precision. Results Easy scan operator 1 and zirconia dust operator 1 differ by 0.16000 (p = 0.0802). In scenario 2, easy scan operator 2 and zirconia dust operator 2 differ by 0.21900 (p = 0.0212) . Operator type significantly affects performance, emphasizing the need to account for operator variability in relevant contexts. The trueness values obtained for zirconia dust and easy scan among both operators were statistically insignificant.  Conclusion Zirconia dust can be reliably used for extraoral scanning of abutments in place of optical scanning sprays.

A Comparison of the Edge Testing of Indirect Composite Layered Zirconia Crowns and Monolithic Zirconia Crowns Without Aging: An In Vitro Study.

Introduction The main reason veneered zirconia restorations fail is due to porcelain veneer chipping. This chipping usually starts from wear marks on the chewing surface. As a result, small cracks under the contact area can grow into larger ones across the veneer layer. The veneer ceramic layer is more vulnerable to fractures because it has lower toughness and slightly lower stiffness compared to the base framework material. Thus, even when there's significant chipping, the main framework material usually stays protected with a thin layer of veneer ceramic on top. The aim of this in vitro study is to compare the edge strength of Monolithic Zirconia Crowns with that of Indirect Composite Layered Zirconia Crowns without aging. Materials and methods This research involved creating 12 hand-layered all-ceramic crowns and 12 indirect composite layered zirconia crowns. The sample size was determined using a G*Power calculation (Heinrich-Heine-Universität Düsseldorf, Düsseldorf, Germany). The zirconia frameworks (Upcera HT White; UPCERA Dental America Inc., Cerritos, CA, US) were milled and sintered following the manufacturer's instructions. For the all-ceramic group, veneering porcelain (e.max Ceram; Ivoclar Vivadent, Schaan, Liechtenstein) was hand-applied. In contrast, the indirect composite group utilized Ceramage (Shofu, Kyoto, Japan). An Instron 4501 universal testing machine (Instron Corp., Canton, MA, USA) was employed for the edge chipping tests, and a Vickers indenter (Shanghai Toyo Diamond Tools Co., LTD, Shanghai, China) was used to apply the load. The mean value for edge chipping was analyzed using an unpaired t-test with IBM SPSS Statistics for Windows, Version 26 (Released 2019; IBM Corp., Armonk, NY, USA). The normality of the data was confirmed, and statistical significance was set at 0.05. Results Monolithic Zirconia Crowns (Group 1) require significantly more force (mean: 405 N) to induce an edge chip compared to Indirect Composite Layered Zirconia Crowns (Group 2) (mean: 300 N). The 95% confidence interval (83.43261 N to 109.90072 N) confirms the statistical significance of this difference. Conclusion In conclusion, when evaluating restorative materials based on both esthetic and functional criteria, monolithic zirconia stands out due to its combination of strength, esthetic potential, biocompatibility, and versatility.

Effectiveness of Denture Cleansers on Candida albicans Biofilm on Conventionally Fabricated, Computer-Aided Design/Computer-Aided Manufacturing-Milled, and Rapid-Prototyped Denture Base Resins: An In Vitro Study.

INTRODUCTION: Conventionally fabricated denture base resins have been used for over 150 years. Newer denture base resins can provide a superior fit and may be customized to the patient's characteristics, but the literature on their cleansibility remains limited. The oral cavity can be a hub for thousands of microflora. The maintenance of complete dentures by edentulous patients depends not only on the maintenance of the patient but also on the material used, biofilm adherence, and polishability. MATERIALS AND METHODS: Cuboid specimens of 10 × 5 × 2 mm were designed using the Meshmixer version 3.5 software (Meshmixer, Australia). The standard tessellation (STL) file was imported and sent for printing (NextDent, Netherlands) (Group 1), milling in polymethyl methacrylate (PMMA) (Ivotion, Ivoclar, Schaan, Liechtenstein) (Group 2), and wax milling (Upcera, China), followed by flasking, counter flasking, and packing using heat-cured acrylic resin (DPI, India) (Group 3). The obtained specimens were polished using pumice and sterilized using a UV sterilization unit. The specimens were then immersed in a suspension of candida broth. After three days of biofilm formation, a colony count was performed and noted as colony-forming units per milliliter (CFU/mL). Specimens were treated using Secure denture cleansing tablets (Ghent, New York), table salt (iodized table salt, Tata, India), Clinsodent (ICPA, Mumbai, India), and Polident denture cleansing powder (Polident, Ontario, Canada). A colony count was done after treatment, and the data were tabulated. Statistical analysis was done using SPSS software to compare the efficiency of denture cleansers in all three groups, and statistical significance was set at 0.05. The Kolmogorov-Smirnov test was done to confirm the normality of the data, followed by a one-way analysis of variance (ANOVA) test to compare the efficiency of denture cleansers on the removal of candida colonies. RESULTS: Milled denture base resins showed a significantly lower colony count when compared to printed and conventionally fabricated denture base resins. The denture cleansers showed high efficacy in all groups, with the most significant being Secure, which showed a mean difference ranging from 8.114 to 9.887 CFU/mL, followed by Clinsodent, showing a mean of 6.699-9.863 CFU/mL, followed closely by Polident, showing 4.964-7.114 CFU/mL, followed by table salt, being 5.254-8.920 CFU/mL. The 95% confidence interval confirmed statistical significance. CONCLUSION: The highest candida colony count was demonstrated by the conventional, followed by rapid prototyping, and was least with milled denture base resins. Following treatment with denture cleansers, Secure demonstrated almost complete eradication of colonies, making it the most effective option. Salt exhibited the lowest efficiency, followed closely by Polident and Clinsodent, and the most effective was Secure denture cleanser.

The endocrinologist gap: Managing diabetes patients in absence of a specialist.

The treatment of pediatric patients with diabetes is frequently orchestrated within a multidisciplinary framework at tertiary, specialized institutions. In situations where emergent surgery is indicated or when a procedure is scheduled in a facility devoid of an endocrinology service, the onus of managing perioperative glycemic levels may rest with the attending anesthesiologist. The objective of this review is to furnish a comprehensive examination of the anesthetic considerations and perioperative governance of pediatric patients with diabetes. Furthermore, this paper delineates a streamlined protocol for perioperative glycemic control, tailored to both major and minor surgical interventions.

ERAS following Gastrectomy for Octo- and Nonagenarians: A Single-Center Retrospective Analysis.

Background: The safety and efficacy of enhanced recovery after surgery (ERAS) following elective gastrectomy for gastric cancer in patients >80 years of age are not well described. The aim of this study was to explore whether an ERAS protocol following gastrectomy in this age group can be safely implemented and reduce postoperative length of stay. Methods: A retrospective, single-center analysis was performed. All patients >80 years of age with gastric cancer undergoing elective subtotal and total gastrectomy between January 2010 and December 2021 were identified. With the implementation of an ERAS protocol in January 2016, patients treated beforehand were allocated to Group A (pre-ERAS) and Group B (ERAS). The length of stay, incidence of postoperative complications and representation/readmission to the hospital were compared between the groups. Results: Of the 221 patients identified, 56 met the inclusion criteria with 22 patients (39.3%) allocated to Group A and 34 patients (60.7%) to Group B. There were no differences with regard to the type of resection and surgical approach. Length of stay was shorter in Group B (5 days, range 2-27 versus 10 days, 3-109, P = .040). A trend toward more discharges by postoperative day 3 was noted among patients in Group B (7/34, 20.6% versus 2/22, 9.1%, P = .253). There were no differences in the incidence of postoperative complications or readmission hospital between the groups. Conclusion: Among patients >80 years of age, ERAS following gastrectomy for cancer is associated with a reduced length of stay and can be safely implemented.

Denture base materials: An in vitro evaluation of the mechanical and color properties.

OBJECTIVES: This study aimed to compare the physical and mechanical properties of four denture base materials: Polyan IC (PA), milled polymethylmethacrylate (PMMA), three-dimensional (3D)-printed resin (3DP), and SR Ivocap (SR). METHODS: Ninety-six samples were prepared and divided into four groups as follows. Group A consisted of 3DP (Asiga DentaBASE, Asiga) fabricated using a manufacturer-recommended 3D printer (Asiga Pro 4k, Asiga). Group B comprised milled PMMA (MP) (Ivotion Base, Ivoclar Vivadent). Group C included PA (BredentSenden), meanwhile, group D involved SR (Ivoclar VivadentSchaan). Cuboid samples (65 mm x 10 mm x 2.5 mm) were used for biaxial flexure strength testing in a universal testing machine (UTM). Cylindrical samples of 20 mm x 40 mm were used for compressive strength testing in a UTM. Additionally, cuboid samples (65 mm x 10 mm x 2.5 mm) were used for Vickers surface hardness testing in a microhardness tester. disk samples (10 mm x 2.5 mm) were employed for color stability testing both in a coffee solution and Coca-Cola, using a digital spectrophotometer. Statistical analyses were performed using one-way analysis of variance and Tukey's post hoc analysis (α=0.05). RESULTS: MP demonstrated superior compressive strength (p = 0.002) and color stability compared to that exhibited by 3DP (p < 0.001) while displaying similar flexure strength (p = 0.336) and hardness (p = 0.708). MP and PA displayed similar compressive strength (p = 0.081), flexure strength (p = 0.159), and color stability in coke (p = 0.071). However, MP had reduced hardness (p < 0.001) and color stability in coffee (p < 0.001). Moreover, MP demonstrated a higher compressive strength (p < 0.001) than that displayed by SR. However, the flexure strength, hardness, and color stability were similar (p > 0.05). Furthermore, 3DP exhibited comparable compressive strength (p = 0.334) to that of PA but demonstrated significantly lower flexure strength (p = 0.005), hardness (p < 0.001), and color stability (p < 0.001) compared to PA. In comparison to SR, PA had a higher compressive strength (p < 0.001), hardness (p = 0.001), and color stability in coffee (p < 0.001), although they demonstrated similar (p > 0.05) flexure strength and color stability in coke. CONCLUSIONS: The MP and PA demonstrated superior compressive strength than that exhibited by the other materials tested. The tested materials had similar flexure strengths, except for PA which demonstrated superiority over the 3DP. Among all tested materials, PA exhibited the highest hardness, while the 3DP was the least color-stable. CLINICAL SIGNIFICANCE: Considering the mechanical properties and color stability, Polyan and milled polymethylmethacrylate are preferred for complete denture fabrication. However, the limited repairability and complex handling of Polyan should be considered.

Cannabis Use Characteristics Associated with Self-Reported Cognitive Function in a Nationally Representative U.S. sample.

BACKGROUND: With increases in cannabis use and potency, there is a need to improve our understanding of the impact of use on cognitive function. Previous research indicates long-term cannabis use may have a negative effect on executive function. Few studies have examined persistence of it in protracted abstinence, and there is limited evidence of predictors of worse cognitive function in current and former users. In this study, we aim to evaluate the associations between cannabis use status (current, former, and never use) and self-report cognition. Further, we investigate if cannabis use characteristics predict self-report cognitive function. METHODS: Cross-sectional cannabis use data from the National Epidemiological Survey on Alcohol and Related Conditions-III (NESARC-III), a national survey (N = 36,309) conducted in the USA between 2012 and 2013 were used alongside the Executive Function Index scales. The data were analyzed by using Ordinary Least Squares regression. RESULTS: Current (N = 3,681, Female = 37.7%) and former users (N = 7,448, Female = 45.4%) reported poorer cognition than never users (N = 24,956, Female = 56.6%). Self-reported cognition of former users was in-between that of current and never users. Several cannabis use characteristics were associated with self-reported cognition in current and former users. CONCLUSION: While prospective studies are required to confirm, findings suggest cannabis use is linked to worse cognition. There may be some limited recovery of cognition in former users and some cannabis use characteristics predict impairment. These findings add to our understanding of the cognitive impact of cannabis use. As worse cognitive function may impact relapse, findings have implications for personalization of cannabis use disorder treatment.

Evaluation and assessment of the survival of tooth implant supported prosthesis in tooth and implant supported rehabilitation cases with metal frameworks.

INTRODUCTION: Over the years, implant therapy has been a commonly used treatment option for individuals who are partially or totally edentulous, with a long-term success rate of over 90%. With significant advancements in biomaterials and technology, implant dentistry can now conduct prosthetic rehabilitations in the majority of patients catering to all types of needs. However, in order to meet the demands of a patient base that is always growing, new trends in implantology are emerging in recent years that are focused on minimally invasive surgery and financial sustainability. In certain clinical scenarios, connecting teeth and implants to support fixed partial prosthesis (FPPs) may be a predictable and workable course of treatment. MATERIALS AND METHODS: 22 patients were selected for this study who had tooth and implant supported prosthesis placed as a final restoration. Out of these 22 patients; 12 were male and 10 were female patients. Implants were placed following proper protocol and if grafting procedures were required they were carried out. A second stage surgical procedure was carried out and delayed loading protocols were followed. The statistical analysis was done using the IBM SPSS 24.0, Chicago, USA. The survival of the implants and teeth were measured by the Kaplan Meier survival scale. Bone loss was assessed at baseline(upon loading), 12 months and 24 months. RESULTS: The implant survival rate was measured at 6 months, 12 months, 18 months and 24 months. At 24 months, one implant showed failure, so the survival rate of the implants were 95.4%. Bone loss of 1 mm was seen around one implant at 12 months. Bone loss of 1 and 2 mm was present around two implants and one implant respectively at 24 months. CONCLUSION: From the results of this study, we can conclude that tooth implant supported prosthesis show very good survival when used in rehabilitation cases.

Association of Age, Gender, and Site of Implant Placement: An Institution-Based Retrospective Study.

Tooth loss is an undesirable condition that leads to functional, esthetic and social damage, having an impact on an individual's quality of life. Dental implants are man-made tooth root replacements that are increasingly used to replace a missing tooth. It is important to gather demographic data in order to take precautions before the possible failures. Hence the objective of this study was to retrospectively determine the association between age, gender, and site of implant placement in patients reporting to a private dental institution. This study was carried out from the data obtained from the case records of 1281 patients who had undergone implant therapy. Chi-square test was applied to see associations of gender, age and implant site. The results show that a maximum number of 348 implants (27.7%) were placed in patients aged between 41-50 years. The patient pool consisted of 705 (55%) females and 576 (45%) males. A maximum of 228 implants (17.80%) were placed in region 46 and 224 implants (17.49%) in region 36. Only 2 implants (0.2%) were placed in region 41. There was a positive association between age, gender and site of implant. In those aged 20-30 years, 20.53% of implants were placed, 26.23% in 31-40 years, 27.1% in 41-50 years, 17.95% in 51-60 years and 8.11% in 61-70 years of age. In male, a maximum of 124 implants (54.4%) were placed in region 46 and only 1 implant (50%) in region 41. In females, region 36 had a maximum of 110 implants (49.1%), and the least number of implants were placed in regions 31 and 41. In this study, it can be concluded that general factors such as age and gender had a significant effect on the site of implant placement.

Evaluation and assessment of the wettabilty and water contact angle of modified poly methyl methacrylate denture base materials against PEEK in cast partial denture framework: an in vitro study.

INTRODUCTION: The prevalence of adults with partially dental arches is expected to be more than imagined and patients requiring replacement of missing teeth are slowly increasing in number too. Removable partial dentures are known to provide for substantial replacement for the missing teeth with also added advantages when compared to fixed or implant prosthesis, mainly in elderly patients. Denture base material performance and durability are greatly influenced by wettability and water contact angle. In the case of dentures; adequate moisture distribution is necessary to ensure excellent wettability which has an influence on comfort and oral health. The purpose of conducting this study was to find out whether the advancements made using PEEK (Polyether ether ketone) would prove to be more beneficial than the current upgrades in the current material spectrum. MATERIALS AND METHODS: This study was performed under in vitro conditions. All the fabrication and processing was done only by one operator. The materials used were divided into three groups each comprising 20 samples. Group A was modified polymethylmethacrylate (Bredent Polyan), Group B was polyoxymethylene acetal resin (Biodentaplast) and Group C was PEEK. An Ossila Goniometer was used to measure the contact angle. The three types of liquids used for the testing included distilled water, natural saliva and mouth wetting solution (Wet Mouth Liquid, ICPA India). Human saliva was collected from an individual with no medical conditions and normal salivary secretion. RESULTS: The data was analyzed using One-way ANOVA test and a pairwise comparison using the Post Hoc Tukey's Honest Significant Difference. Table 1 consists of the mean water contact angles of the denture base materials and mean contact angles of various denture base materials. In saliva, mouth wetting solution and distilled water, the highest mean and least mean contact angle was seen in Polyan and Biodentaplast respectively. A signicant difference was seen between PEEK and Polyan and Biodentaplast and Polyan on further comparison. CONCLUSION: From the resources and the materials at our disposal, it could be concluded that Polyan, Biodentaplast and PEEK and could be used as viable options in cast partial denture framework.

A comparative evaluation of physical properties of CAD/CAM complete denture resins- an in vitro study.

BACKGROUND: In dentistry, there is a growing preference for computer-aided design and computer-aided manufacturing (CAD/CAM) systems over traditional laboratory procedures. However, there is not much literature comparing various CAD/CAM materials. Thus, this study aimed to assess and compare the color stability and hardness of gingival and tooth colored milled and 3D-printed acrylic resins. MATERIALS AND METHODS: Four types of CAD/CAM materials were prepared: 3D-printed pink shade (PP), milled polymenthymethacrylate (PMMA) pink shade (MP), 3D-printed tooth shade (PT) and milled PMMA tooth shade (MT) (n = 6). For hardness, disc shaped samples of 15 mm × 2 mm and for color stability, bar shaped samples of 65mmx10mmx2.5 mm were prepared and polished. Vickers hardness test was performed in a microhardness tester. Color stability test was done by immersing in coffee solution and coca cola for 7 days. Day 0 and day 7 measurements were recorded using a digital spectrophotometer and the change in color was calculated. For statistical analysis, one-way ANOVA and Tukey's post hoc tests were done. RESULTS: For color stability, milled PMMA was superior to 3D-printed resin samples. Milled pink and tooth shade samples had similar color stability, whereas 3D-printed tooth shade samples were more color stable as compared to pink shade 3D-printed samples. For hardness, milled tooth shade PMMA was the most superior one, followed by 3D-printed tooth shade, whereas pink shade milled PMMA and 3D-printed resin samples had similar hardness values and were inferior to the tooth shade CAD/CAM materials. CONCLUSION: Color stability of milled PMMA is superior to that of 3D-printed resins. Hardness of tooth shade milled and 3D-printed resins is more than that of pink shade milled and 3D-printed resins.

Nanozymes and carbon-dots based nanoplatforms for cancer imaging, diagnosis and therapeutics: Current trends and challenges.

Cancer patients face a significant clinical and socio-economic burden due to increased incidence, mortality, and poor survival. Factors like late diagnosis, recurrence, drug resistance, severe side effects, and poor bioavailability limit the scope of current therapies. There is a need for novel, cost-effective, and safe diagnostic methods, therapeutics to overcome recurrence and drug resistance, and drug delivery vehicles with enhanced bioavailability and less off-site toxicity. Advanced nanomaterial-based research is aiding cancer biologists by providing solutions for issues like hypoxia, tumor microenvironment, low stability, poor penetration, target non-specificity, and rapid drug clearance. Currently, nanozymes and carbon-dots are attractive due to their low cost, high catalytic activity, biocompatibility, and lower toxicity. Nanozymes and carbon-dots are increasingly used in imaging, biosensing, diagnosis, and targeted cancer therapy. Integrating these materials with advanced diagnostic tools like CT scans and MRIs can aid in clinical decision-making and enhance the effectiveness of chemotherapy, photothermal, photodynamic, and sonodynamic therapies, with minimal invasion and reduced collateral effects.

Docetaxel-Based Neoadjuvant Chemotherapy Followed by En Bloc Resection for Esophageal Adenocarcinoma: A 15-Year Retrospective Analysis from a Regional Upper Gastrointestinal Cancer Network.

BACKROUND: Real-world, long-term survival outcomes of neoadjuvant, docetaxel-based therapy for esophageal and junctional adenocarcinoma are lacking. This study describes the long-term survival outcomes of patients with esophageal and junctional adenocarcinoma treated with neoadjuvant docetaxel-based chemotherapy and en bloc transthoracic esophagectomy. METHODS: A retrospective cohort analysis of a prospectively maintained database from a regional upper gastrointestinal cancer network in Quebec, Canada, was performed. From January 2007 to December 2021, all patients with locally advanced (cT3 and/or N1) esophageal/Siewert I/II adenocarcinoma treated with neoadjuvant DCFx3 (Docetaxel/Cisplatin/5FU) or FLOTx4 (5FU/Leucovorin/Oxaliplatin/Docetaxel) and transthoracic en bloc esophagectomy were identified. Postoperative, pathological, and survival outcomes were compared. RESULTS: Overall, 236 of 420 patients met the inclusion criteria. Tumor location was esophageal/Siewert I/Siewert II (118/33/85), most were cT3-4 (93.6%) and cN+ (61.0%). DCF and FLOT were used in 127 of 236 (53.8%) and 109 of 236 (46.2%). All neoadjuvant cycles were completed in 87.3% with no difference between the regimens. Operative procedures included Ivor Lewis (81.8%), left thoraco-abdominal esophagectomy (10.6%) and McKeown (7.6%) with an R0 resection in 95.3% and pathological complete response in 9.7% (DCF 12.6%/FLOT 6.4%, p = 0.111). The median lymph node yield was 32 (range 4-79), and 60.6% were ypN+. Median follow-up was longer for the DCF group (74.8 months 95% confidence interval [CI] 4-173 vs. 37.8 months 95% CI 2-119, p <0.001. Overall survival was similar between the groups (FLOT 97.3 months, 78.6-115.8 vs. DCF 92.9, 9.2-106.5, p = 0.420). CONCLUSIONS: Neoadjuvant DCF and FLOT followed by transthoracic en bloc resection are both highly effective regimens for locally advanced esophageal adenocarcinoma with equivalent survival outcomes despite high disease load.

Evaluation and Assessment of the Colour Stability of Modified Polymethyl Methacrylate Denture Base Materials and Polyether Ether Ketone in a Cast Partial Denture Framework: An In-Vitro Study.

Background One of the frequent aesthetic issues patients confront is the loss of colour and lifeless appearance of the dentures of the base materials of their dentures after regular use. This leads to a lack of motivation to use the denture regularly. Due to the drawbacks of conventional PMMA, polyether ether ketone (PEEK) and newer polymethyl methacrylate (PMMA)-based materials have now started being used in cast partial denture frameworks due to their superior physical and biological properties. The lack of long-lasting colour is one of the main reasons for the repeat of dental prostheses. Hence, the need for the study is to help clinicians decide which would be the most suitable denture base material to be used based on colour stability. Aim To assess and compare the colour stability of PEEK, polyan, and biodentaplast denture base materials (DBMs) upon staining with distilled water, tea, coffee, and turmeric solutions after one day, seven days, and 30 days. Methods A total of 20 cuboidal specimens were constructed and immersed in distilled water, tea, coffee, and turmeric (five specimens of each material in each solution, a total of 60 specimens): Group 1: PEEK, Group 2: polyan, Group 3: biodentaplast. All specimens were subjected to colour measurements before exposure to beverage solutions, after 24 hours, on the seventh day and 30th day with a colour reflectance spectrophotometer with computer software. A one-way ANOVA test followed by post hoc Tukey's honestly significant difference (HSD) was performed for comparison of colour stability between the DBMs, revealing a significant difference between PEEK and polyan and PEEK and biodentaplast. Polyan showed the highest delta E values, followed by biodentaplast and PEEK. A two-way ANOVA test, followed by Tukey's HSD post hoc, was done to compare the staining ability of various staining solutions. Turmeric had the highest delta E values, followed by coffee, tea, and distilled water. Data were assessed using Statistical Product and Service Solutions (SPSS, version 23) (IBM SPSS Statistics for Windows, Armonk, NY) software. Results The highest mean delta E value at T1 was seen in biodentaplast immersed in turmeric (12.3900+/-0.442), and the least value at T1 was obtained for PEEK immersed in distilled water (0.4460+/-0.036). The highest mean delta E value at T2 was seen in polyan immersed in turmeric (13.0160+/-0.28962), and the least value at T2 was obtained for PEEK immersed in distilled water (0.5860+/-0.051). At T3, the highest mean delta E value was seen in polyan immersed in turmeric (16.8600+/-0.49845), and the least value at T3 was obtained for PEEK immersed in distilled water (0.700+/-0.037). Conclusion PEEK had the highest colour stability when compared with polyan and biodentaplast.

Incorporating mutational heterogeneity to identify genes that are enriched for synonymous mutations in cancer.

BACKGROUND: Synonymous mutations, which change the DNA sequence but not the encoded protein sequence, can affect protein structure and function, mRNA maturation, and mRNA half-lives. The possibility that synonymous mutations might be enriched in cancer has been explored in several recent studies. However, none of these studies control for all three types of mutational heterogeneity (patient, histology, and gene) that are known to affect the accurate identification of non-synonymous cancer-associated genes. Our goal is to adopt the current standard for non-synonymous mutations in an investigation of synonymous mutations. RESULTS: Here, we create an algorithm, MutSigCVsyn, an adaptation of MutSigCV, to identify cancer-associated genes that are enriched for synonymous mutations based on a non-coding background model that takes into account the mutational heterogeneity across these levels. Using MutSigCVsyn, we first analyzed 2572 cancer whole-genome samples from the Pan-cancer Analysis of Whole Genomes (PCAWG) to identify non-synonymous cancer drivers as a quality control. Indicative of the algorithm accuracy we find that 58.6% of these candidate genes were also found in Cancer Census Gene (CGC) list, and 66.2% were found within the PCAWG cancer driver list. We then applied it to identify 30 putative cancer-associated genes that are enriched for synonymous mutations within the same samples. One of the promising gene candidates is the B cell lymphoma 2 (BCL-2) gene. BCL-2 regulates apoptosis by antagonizing the action of proapoptotic BCL-2 family member proteins. The synonymous mutations in BCL2 are enriched in its anti-apoptotic domain and likely play a role in cancer cell proliferation. CONCLUSION: Our study introduces MutSigCVsyn, an algorithm that accounts for mutational heterogeneity at patient, histology, and gene levels, to identify cancer-associated genes that are enriched for synonymous mutations using whole genome sequencing data. We identified 30 putative candidate genes that will benefit from future experimental studies on the role of synonymous mutations in cancer biology.