RESUMO
Copper iodide (CuI) has garnered considerable attention as a promising alternative to p-type transparent conducting oxides owing to its low cation vacancy formation energy, shallow acceptor level, and readily modifiable conductivity via doping. Although sulfur (S) doping through liquid iodination has exhibited high efficacy in enhancing the conductivity with record high figure of merit (FOM) of 630 00 MΩ-1, solution-processed S-doped CuI (CuI:S) for low-cost large area fabrication has yet to be explored. Here, a highly conducting CuI:S thin-film for p-type transparent conducting electrode (TCE) is reported using low temperature solution-processing with thiourea derivatives. The optimization of thiourea dopant is determined through a comprehensive acid-base study, considering the effects of steric hindrance. The modification of active groups of thioureas facilitated a varying carrier concentration range of 9 × 1018-2.52 × 1020 cm-3 and conductivities of 4.4-390.7 S cm-1. Consequently, N-ethylthiourea-doped CuI:S exhibited a FOM value of 7 600 MΩ-1, which is the highest value among solution-processed p-type TCEs to date. Moreover, the formulation of CuI:S solution for highly conductive p-type TCEs can be extended to CuI:S inks, facilitating high-throughput solution-processes such as inkjet printing and spray coating.
RESUMO
Chalcogenide aerogels (chalcogels) are amorphous structures widely known for their lack of localized structural control. This study, however, demonstrates a precise multiscale structural control through a thiostannate motif ([Sn2S6]4-)-transformation-induced self-assembly, yielding Na-Mn-Sn-S, Na-Mg-Sn-S, and Na-Sn(II)-Sn(IV)-S aerogels. The aerogels exhibited [Sn2S6]4-:Mn2+ stoichiometric-variation-induced-control of average specific surface areas (95-226 m2 g-1), thiostannate coordination networks (octahedral to tetrahedral), phase crystallinity (crystalline to amorphous), and hierarchical porous structures (micropore-intensive to mixed-pore state). In addition, these chalcogels successfully adopted the structural motifs and ion-exchange principles of two-dimensional layered metal sulfides (K2xMnxSn3-xS6, KMS-1), featuring a layer-by-layer stacking structure and effective radionuclide (Cs+, Sr2+)-control functionality. The thiostannate cluster-based gelation principle can be extended to afford Na-Mg-Sn-S and Na-Sn(II)-Sn(IV)-S chalcogels with the same structural features as the Na-Mn-Sn-S chalcogels (NMSCs). The study of NMSCs and their chalcogel family proves that the self-assembly principle of two-dimensional chalcogenide clusters can be used to design unique chalcogels with unprecedented structural hierarchy.
RESUMO
Three Li- and Mg-cosubstituted compounds in the Gd5-x(Li/Mg)xGe4 (x = 1.04(2), 1.17(2), 1.53(2)) system have been successfully prepared by conventional high-temperature reactions. According to powder and single-crystal X-ray diffraction analyses, all three compounds adopt a Gd5Si4-type phase with the orthorhombic Pnma space group (Pearson code oP16, Z = 4) and six crystallographically independent atomic sites. The crystal structure can be described as a combination of two-dimensional Mo2FeB2-type ∞2[Gd2(Li/Mg)Ge2] layers and [Ge2] dimers. Interestingly, as 64% of Li and 26% of Gd at the RE3 and RE2 sites, respectively, were exclusively substituted by Mg in Gd3.47(1)Li0.36(2)Mg1.17(3)Ge4, the lattice parameter b was selectively shortened as a result of the RE3-Ge1 bond shrinkage in comparison to that in Gd4LiGe4, while lattice parameters a and c remained nearly intact. A series of theoretical calculations using the tight-binding linear muffin-tin orbital (TB-LMTO) method indicated that the reduction of the particular RE3-Ge1 bond distance in the title compounds could also be explained by an optimization of bonding based on the corresponding RE3-Ge1 crystal orbital Hamilton population (COHP) curve. Moreover, the specific site preference of Mg for the RE3 site was supported by both size-factor as well as electronic-factor criteria on the basis of the smallest atomic size and the highest electronegativity of Mg among the three cations. Therefore, the overall electronic structure was further interrogated by a density of states (DOS) analysis. The influence of nonmagnetic Li/Mg cosubstitution for the magnetic Gd atoms in the title Gd5-x(Li/Mg)xGe4 system on the magnetic characteristics was also thoroughly studied by isofield magnetization at 100 Oe and 10 kOe and isothermal magnetization measurements at 4 K using two of the title compounds: Gd3.83(1)Li0.48Mg0.69(3)Ge4 and Gd3.47(1)Li0.36(2)Mg1.17(3)Ge4.
RESUMO
Three Zintl phase compounds belonging to the CaYb4Al2Sb6- xGe x ( x = 0.2, 0.5, 0.7; nominal compositions) system with various Ge-doping contents were successfully synthesized by arc-melting and were initially crystallized in the Ba5Al2Bi6-type phase (space group Pbam, Pearson codes oP26). However, after post-heat treatment at an elevated temperature, the originally obtained crystal structure was transformed into the homeotypic Ca5Ga2Sb6-type structure according to powder and single-crystal X-ray diffraction analyses. Two types of crystal structures share some isotypic structural moieties, such as the one-dimensional anionic chains formed by ∞1[Al2Sb8] and the void-filling Ca2+/Yb2+ mixed cations, but the slightly different spatial arrangements in each unit cell make these two structural types distinguishable. This series of title compounds is originally investigated to examine whether anionic p-type doping using Ge can successfully enhance thermoelectric (TE) properties of the Yb-rich CaYb4Al2Sb6- xGe x series even after the phase transition from the Ba5Al2Bi6-type to the Ca5Ga2Sb6-type phase. More interestingly, we also reveal that the given structural transformation is triggered by the particularly different site-preference of Ca2+ and Yb2+ among three available cationic sites in each structure type, which is significantly affected by thermodynamic conditions of this system. Band structure and density of states analyses calculated by density functional theory using the tight-binding linear muffin-tin orbital method also prove that the Ge-doping actually increases band degeneracies and the number of resonant peaks near the Fermi level resulting in the improvement of Seebeck coefficients. Electron localization function analyses for the (0 1 0) sliced-plane and the 3D isosurface nicely illustrates the distortion of the paired-electron densities due to the introduction of Ge. The systematic TE property measurements imply that the attempted anionic p-type doping is indeed effective to improve the TE characteristics of the title CaYb4Al2Sb6- yGe y system.
RESUMO
Topological insulators generally share commonalities with good thermoelectric (TE) materials because of their narrow band gaps and heavy constituent elements. Here, we propose that a topological crystalline insulator (TCI) could exhibit a high TE performance by breaking its crystalline symmetry and tuning the chemical potential by elemental doping. As a candidate material, we investigate the TE properties of the Cl-doped TCI Pb0.7Sn0.3Se. The infrared absorption spectra reveal that the band gap is increased from 0.055 eV for Pb0.7Sn0.3Se to 0.075 eV for Pb0.7Sn0.3Se0.99Cl0.01, confirming that the Cl doping can break the crystalline mirror symmetry of a TCI Pb0.7Sn0.3Se and thereby enlarge its bulk electronic band gap. The topological band inversion is confirmed by the extended X-ray absorption fine structure spectroscopy, which shows that the TCI state is weakened in a chlorine x = 0.05-doped compound. The small gap opening and partial linear band dispersion with massless and massive bands may have a high power factor (PF) for high electrical conductivity with an enhancement of the Seebeck coefficient. As a result, Pb0.7Sn0.3Se0.99Cl0.01 shows a considerably enhanced ZT of 0.64 at 823 K, which is about 1200% enhancement in ZT compared with that of the undoped Pb0.7Sn0.3Se. This work demonstrates that the optimal n-type Cl doping tunes the chemical potential together with breaking the state of the TCI, suppresses the bipolar conduction at high temperatures, and thereby enables the Seebeck coefficient to increase up to 823 K, resulting in a significantly enhanced PF at high temperatures. In addition, the bipolar contribution to thermal conductivity is effectively suppressed for the Cl-doped samples of Pb0.7Sn0.3Se1- xCl x ( x ≥ 0.01). We propose that breaking the crystalline mirror symmetry in TCIs could be a new research direction for exploring high-performance TE materials.
RESUMO
Topological insulators have attracted much interest in topological states of matter featuring unusual electrical conduction behaviors. It has been recently reported that a topological crystalline insulator could exhibit a high thermoelectric performance by breaking its crystal symmetry via chemical doping. Here, we investigate the multiple effects of Na, Se, and S alloying on thermoelectric properties of a topological crystalline insulator Pb0.6Sn0.4Te. The Na doping is known to be effective for breaking the crystalline mirror symmetry of Pb0.6Sn0.4Te. We demonstrate that simultaneous emergence of band convergence by Se alloying and nanostructuring by S doping enhance the power factor and decrease lattice thermal conductivity, respectively. Remarkably, the high power factor of 22.3 µW cm-1 K-2 at 800 K is achieved for Na 1%-doped Pb0.6Sn0.4Te0.90Se0.05S0.05 mainly due to a relatively high Seebeck coefficient via band convergence by Se alloying as well as the suppression of bipolar conduction at high temperatures by the increase of energy band gap. Furthermore, the lattice thermal conductivity is significantly suppressed by PbS nanoprecipitates without deteriorating the hole carrier mobility, ranging from 0.80 W m-1 K-1 for Pb0.6Sn0.4Te to 0.17 W m-1 K-1 at 300 K for Pb0.6Sn0.4Te0.85Se0.10S0.05. As a result, the synergistically combined effects of breaking the crystalline mirror symmetry of topological crystalline insulator, band convergence, and nanostructuring for Pb0.6Sn0.4Te0.95- xSe xS0.05 ( x = 0, 0.05, 0.1, 0.2, and 0.95) give rise to an impressively high ZT of 1.59 at 800 K for x = 0.05. We suggest that the multiple doping in topological crystalline insulators is effective for improving the thermoelectric performance.
RESUMO
The recent development of high-performance colloidal quantum dot (QD) thin-film transistors (TFTs) has been achieved with removal of surface ligand, defect passivation, and facile electronic doping. Here, we report on high-performance solution-processed CdSe QD-TFTs with an optimized surface functionalization and robust defect passivation via hydrazine-free metal chalcogenide (MCC) ligands. The underlying mechanism of the ligand effects on CdSe QDs has been studied with hydrazine-free ex situ reaction derived MCC ligands, such as Sn2S64-, Sn2Se64-, and In2Se42-, to allow benign solution-process available. Furthermore, the defect passivation and remote n-type doping effects have been investigated by incorporating indium nanoparticles over the QD layer. Strong electronic coupling and solid defect passivation of QDs could be achieved by introducing electronically active MCC capping and thermal diffusion of the indium nanoparticles, respectively. It is also noteworthy that the diffused indium nanoparticles facilitate charge injection not only inter-QDs but also between source/drain electrodes and the QD semiconductors, significantly reducing contact resistance. With benign organic solvents, the Sn2S64-, Sn2Se64-, and In2Se42- ligand based QD-TFTs exhibited field-effect mobilities exceeding 4.8, 12.0, and 44.2 cm2/(V s), respectively. The results reported here imply that the incorporation of MCC ligands and appropriate dopants provide a general route to high-performance, extremely stable solution-processed QD-based electronic devices with marginal toxicity, offering compatibility with standard complementary metal oxide semiconductor processing and large-scale on-chip device applications.
RESUMO
It has been a difficulty to form well-distributed nano- and mesosized inclusions in a Bi2Te3-based matrix and thereby realizing no degradation of carrier mobility at interfaces between matrix and inclusions for high thermoelectric performances. Herein, we successfully synthesize multistructured thermoelectric Bi0.4Sb1.6Te3 materials with Fe-rich nanoprecipitates and sub-micron FeTe2 inclusions by a conventional solid-state reaction followed by melt-spinning and spark plasma sintering that could be a facile preparation method for scale-up production. This study presents a bismuth antimony telluride based thermoelectric material with a multiscale structure whose lattice thermal conductivity is drastically reduced with minimal degradation on its carrier mobility. This is possible because a carefully chosen FeTe2 incorporated in the matrix allows its interfacial valence band with the matrix to be aligned, leading to a significantly improved p-type thermoelectric power factor. Consequently, an impressively high thermoelectric figure of merit ZT of 1.52 is achieved at 396 K for p-type Bi0.4Sb1.6Te3-8 mol % FeTe2, which is a 43% enhancement in ZT compared to the pristine Bi0.4Sb1.6Te3. This work demonstrates not only the effectiveness of multiscale structuring for lowering lattice thermal conductivities, but also the importance of interfacial band alignment between matrix and inclusions for maintaining high carrier mobilities when designing high-performance thermoelectric materials.
RESUMO
Two Zintl phase thermoelectric compounds of Eu11-xKxBi10-ySny (x = 0, 0.26(1); y = 0.86(2), 1.93(2)) have been synthesized by a high-temperature solid-state reaction and arc-melting methods. The two isotypic crystal structures are characterized by both single-crystal and powder X-ray diffractions, and adopt a tetragonal Ho11Ge10-type structure (space group I4/mmm, Z = 2, Pearson code tI84) containing nine crystallographically independent asymmetric atomic sites in a unit cell. The chemical compositions are confirmed by EDS analysis. The complex crystal structure of the two title compounds can be described as an assembly of three different types of co-facial polyhedra formed by cations and 3-dimensional anionic frameworks surrounding these polyhedra. A quaternary title compound, Eu10.74(2)K0.26Bi9.14(2)Sn10.86, which simultaneously contains both cationic and anionic p-dopants in a single compound, was successfully crystallized for the first time in the A11M10 (A = alkaline-earth metals, rare-earth metals; M = triels, tetrels, pnictogens) series. In particular, two different types of p-dopants K and Sn show particular site-preferences, respectively, where K and Sn prefer to occupy the cationic Wyckoff 4e site and the anionic Wyckoff 8h site. These noticeable site preferences can be elucidated by either a size-factor criterion for the K-doping case or by an electronic-factor criterion for the Sn-doping case. The tight-binding linear muffin-tin orbital calculations show that as the double p-doping is applied to the Eu11-xKxBi10-ySny system, some extra holes are generated on the electronic structures according to the density of states curves. However, a series of thermoelectric property measurements prove that this extra hole-carrier doping is hardly effective enough to completely suppress a bipolar conduction of holes and electrons due to the rigid metallic band structure of the title system.
RESUMO
SnSe emerges as a new class of thermoelectric materials since the recent discovery of an ultrahigh thermoelectric figure of merit in its single crystals. Achieving such performance in the polycrystalline counterpart is still challenging and requires fundamental understandings of its electrical and thermal transport properties as well as structural chemistry. Here we demonstrate a new strategy of improving conversion efficiency of bulk polycrystalline SnSe thermoelectrics. We show that PbSe alloying decreases the transition temperature between Pnma and Cmcm phases and thereby can serve as a means of controlling its onset temperature. Along with 1% Na doping, delicate control of the alloying fraction markedly enhances electrical conductivity by earlier initiation of bipolar conduction while reducing lattice thermal conductivity by alloy and point defect scattering simultaneously. As a result, a remarkably high peak ZT of â¼1.2 at 773 K as well as average ZT of â¼0.5 from RT to 773 K is achieved for Na0.01(Sn1-xPbx)0.99Se. Surprisingly, spherical-aberration corrected scanning transmission electron microscopic studies reveal that NaySn1-xPbxSe (0 < x ≤ 0.2; y = 0, 0.01) alloys spontaneously form nanoscale particles with a typical size of â¼5-10 nm embedded inside the bulk matrix, rather than solid solutions as previously believed. This unexpected feature results in further reduction in their lattice thermal conductivity.
RESUMO
The Zintl phase solid-solution Ca11-xYbxSb10-yGez (0 ≤ x ≤ 9; 0 ≤ y ≤ 3; 0 ≤ z ≤ 3) system with the cationic/anionic multisubstitution has been synthesized by molten Sn metal flux and arc-melting methods. The crystal structure of the nine title compounds were characterized by both powder and single-crystal X-ray diffractions and adopted the Ho11Ge10-type structure with the tetragonal space group I4/mmm (Z = 4, Pearson Code tI84). The overall isotypic structure of the nine title compounds can be illustrated as an assembly of three different types of cationic polyhedra sharing faces with their neighboring polyhedra and the three-dimensional cage-shaped anionic frameworks consisting of the dumbbell-shaped Sb2 units and the square-shaped Sb4 or (Sb/Ge)4 units. During the multisubstitution trials, interestingly, we observed a metal-to-semiconductor transition as the Ca and Ge contents increased in the title system from Yb11Sb10 to Ca9Yb2Sb7Ge3 (nominal compositions) on the basis of a series of thermoelectric property measurements. This phenomenon can be elucidated by the suppression of a bipolar conduction of holes and electrons via an extra hole-carrier doping. The tight-binding linear muffin-tin orbital calculations using four hypothetical structural models nicely proved that the size of a pseudogap and the magnitude of the density of states at the Fermi level are significantly influenced by substituting elements as well as their atomic sites in a unit cell. The observed particular cationic/anionic site preferences, the historically known abnormalities of atomic displacement parameters, and the occupation deficiencies of particular atomic sites are further rationalized by the QVAL value criterion on the basis of the theoretical calculations. The results of SEM, EDS, and TGA analyses are also provided.
RESUMO
We investigate the effect of ZnTe incorporation on PbTe to enhance thermoelectric performance. We report structural, microscopic, and spectroscopic characterizations, ab initio theoretical calculations, and thermoelectric transport properties of Pb0.985Na0.015Te-x% ZnTe (x = 0, 1, 2, 4). We find that the solid solubility limit of ZnTe in PbTe is less than 1 mol %. The introduction of 2% ZnTe in p-type Pb0.985Na0.015Te reduces the lattice thermal conductivity through the ZnTe precipitates at the microscale. Consequently, a maximum thermoelectric figure of merit (ZT) of 1.73 at 700 K is achieved for the spark plasma-sintered Pb0.985Na0.015Te-2% ZnTe, which arises from a decreased lattice thermal conductivity of â¼0.69 W m-1 K-1 at â¼700 K in comparison with Pb0.985Na0.015Te.
RESUMO
Thermoelectrics directly converts waste heat into electricity and is considered a promising means of sustainable energy generation. While most of the recent advances in the enhancement of the thermoelectric figure of merit (ZT) resulted from a decrease in lattice thermal conductivity by nanostructuring, there have been very few attempts to enhance electrical transport properties, i.e., the power factor. Here we use nanochemistry to stabilize bulk bismuth telluride (Bi2Te3) that violates phase equilibrium, namely, phase-pure n-type K0.06Bi2Te3.18. Incorporated potassium and tellurium in Bi2Te3 far exceed their solubility limit, inducing simultaneous increase in the electrical conductivity and the Seebeck coefficient along with decrease in the thermal conductivity. Consequently, a high power factor of â¼43 µW cm-1 K-2 and a high ZT > 1.1 at 323 K are achieved. Our current synthetic method can be used to produce a new family of materials with novel physical and chemical characteristics for various applications.
RESUMO
Three new quaternary polar intermetallic compounds of Eu2.94(2)Ca6.06In8Ge8, Eu3.13(2)Ca5.87In8Ge8, and Sr3.23(3)Ca5.77In8Ge8 have been synthesized by a metal-flux method using molten indium metal as a reactive flux, and the novel isotypic crystal structures have been characterized by both powder and single-crystal X-ray diffractions. All compounds crystallize in the orthorhombic space group Pmmn (Z = 2, Pearson symbol oP50) with 14 crystallographically unique atomic positions in the asymmetric unit. The lattice parameters are refined as follows: a = 36.928(2) Å, b = 4.511(1) Å, and c = 7.506(1) Å for Eu2.94(2)Ca6.06In8Ge8; a = 37.171(19) Å, b = 4.531(2) Å, and c = 7.560(4) Å for Eu3.13(2)Ca5.87In8Ge8; and a = 37.350(2) Å, b = 4.550(3) Å, and c = 7.593(4) Å for Sr3.23(3)Ca5.77In8Ge8. In particular, single crystals of two Eu-containing compounds are obtained as bundles of bar/needle-shaped crystals, and the thicknesses of those crystals can be controlled in the range between ca. 300 µm and ca. <10 µm by adjusting several reaction conditions, including the reaction cooling rate and the centrifugation temperature. The overall crystal structure is illustrated as an assembly of (1) the three-dimensional anionic framework, which is formed by the chains of edge-sharing InGe4 tetrahedra and the annulene-like "12-membered anionic rings" connected via Ge2 dimers, and (2) the cationic mixed sites embedded in the space between the anionic frameworks. Theoretical investigations based on tight-binding linear muffin-tin orbital (TB-LMTO) calculations provide a comprehesive understanding of the overall electronic structure and chemical bonding observed among anionic components and between anions and cations. Electron localization function (ELF) and electron density map present chemical bond strengths and polarization within the anionic framework. Magnetic susceptibility measurement proves an antiferromagnetic (AFM) ordering of Eu atoms below 4 K with a reduced effective magnetic moment of 7.12 µB for the Eu atom.
Assuntos
Cloro/química , Condutividade Elétrica , Índio/química , Selênio/química , Temperatura , Movimento (Física)RESUMO
We explored the effect of Cd substitution on the thermoelectric properties of PbTe in an effort to test a theoretical hypothesis that Cd atoms on Pb sites of the rock salt lattice can increase the Seebeck coefficient via the formation of a resonance level in the density of states near the Fermi energy. We find that the solubility of Cd is less than previously reported, and CdTe precipitation occurs to create nanostructuring, which strongly suppresses the lattice thermal conductivity. We present detailed characterization including structural and spectroscopic data, transmission electron microscopy, and thermoelectric transport properties of samples of PbTe-x% CdTe-0.055% PbI(2) (x = 1, 3, 5, 7, 10), PbTe-1% CdTe-y% PbI(2) (y = 0.03, 0.045, 0.055, 0.08, 0.1, 0.2), PbTe-5% CdTe-y% PbI(2) (y = 0.01, 0.03, 0.055, 0.08), and PbTe-1% CdTe-z% Sb (z = 0.3, 0.5, 1, 1.5, 2, 3, 4, 5, 6). All samples follow the Pisarenko relationship, and no enhancement of the Seebeck coefficient was observed that could be attributed to a resonance level or a distortion in the density of states. A maximum ZT of approximately 1.2 at approximately 720 K was achieved for the PbTe-1% CdTe-0.055% PbI(2) sample arising from a high power factor of approximately 17 microW/(cm K(2)) and a very low lattice thermal conductivity of approximately 0.5 W/(m K) at approximately 720 K.