Cyclic Fatigue Comparison of TruNatomy, Twisted File, and ProTaper Next Rotary Systems.

TruNatomy (TN; Dentsply Sirona, Maillefer, Ballaigues, Switzerland) is a newly released system that was not tested in any previous studies. The objective of this work is to evaluate cyclic fatigue resistance of the new file and compare it with the Twisted Files (TF) and ProTaper Next (PTN). Forty-five files were distributed into 3 groups: PTN X2 (size 25 and taper 0.06), TF (size 25 and taper 0.06), and TN prime file (size 26 and taper 0.04). Each group included 15 files. Lengths of all files were 25 mm. Cyclic fatigue testing was done using artificial stainless-steel canals with 60-degree curvature and 5 mm radius. Continuous rotation movement at 300 rpm was used until the file fractures. Time for file separation was recorded in seconds. The number of cycles to failure (NCF) mean and standard deviation for each group was calculated. For statistical analysis of data, ANOVA and Tukey's multiple comparison test were used. Mean and standard deviation (SD) of NCF were 259 ± 37.2, 521.67 ± 63.07 and 846.67 ± 37.16 for PTN, TF, and TN respectively. TN on average had significantly the highest NCF compared with PTN (p < 0.05) and TF (p < 0.05). TruNatomy file showed superior cyclic fatigue resistance. With its potential to preserve tooth structure, this file offers a good cyclic fatigue advantage. However, future studies are required to evaluate other properties of this file and to examine its clinical performance.

Detection of Bone Defects Using CBCT Exam in an Italian Population.

BACKGROUND: The aim of this study was to evaluate the in vivo incidence and the location of fenestrations in a young Italian population by using CBCT. MATERIALS AND METHODS: Fifty patients who had previously performed CBCT for planning third molar extraction or orthodontic therapy were selected for the study. No previous dental treatment had been performed on these patients. Overall, 1,395 teeth were evaluated. Root fenestrations were identified according to the definition of Davies and the American Association of Endodontists. Data was collected and statistically analyzed. RESULTS: Fenestrations were observed in 159 teeth out of 1,395 (11% of teeth). In the lower jaw, we found 68 fenestrations (5%) and 91 in the maxilla (6,5%). Incisors were the teeth with the highest incidence of fenestrations. CONCLUSION: The relative common finding (11%) of fenestration supports the need for CBCT exams before any surgical/implant treatment to avoid complications related to the initial presence of fenestrations. CBCT was found to be an effective and convenient tool for diagnosing fenestration.

Fracture resistance of endodontically treated teeth restored with a bulkfill flowable material and a resin composite.

AIM: To determine and compare the fracture resistance of endodontically treated teeth restored with a bulk fill flowable material (SDR) and a traditional resin composite. METHODS: Thirty maxillary and 30 mandibular first molars were selected based on similar dimensions. After cleaning, shaping and filling of the root canals and adhesive procedures, specimens were assigned to 3 subgroups for each tooth type (n=10): Group A: control group, including intact teeth; Group B: access cavities were restored with a traditional resin composite (EsthetX; Dentsply-Italy, Rome, Italy); Group C: access cavities were restored with a bulk fill flowable composite (SDR; Dentsply-Italy), except 1.5 mm layer of the occlusal surface that was restored with the same resin composite as Group B. The specimens were subjected to compressive force in a material static-testing machine until fracture occurred, the maximum fracture load of the specimens was measured (N) and the type of fracture was recorded as favorable or unfavorable. Data were statistically analyzed with one-way analysis of variance (ANOVA) and Bonferroni tests (P<0.05). RESULTS: No statistically significant differences were found among groups (P<0.05). Fracture resistance of endodontically treated teeth restored with a traditional resin composite and with a bulk fill flowable composite (SDR) was similar in both maxillary and mandibular molars and showed no significant decrease in fracture resistance compared to intact specimens. CONCLUSIONS: No significant difference was observed in the mechanical fracture resistance of endodontically treated molars restored with traditional resin composite restorations compared to bulk fill flowable composite restorations.

In vitro evaluation of carrier based obturation technique: a CBCT study.

AIM: The goal of the study was to compare the ability of two different carrier based obturation (CBO) techniques to reach working length and fill in three-dimensions root canal systems, by using CBCT. MATERIALS AND METHODS: Twenty-six extracted molars were scanned with CBCT and 40 curved canals were selected (between 30° and 90°) and divided in two similar groups (n=20). All canals were prepared up to size 25 taper .06 using nickel-titanium instrumentation. The canals in the Group SC were obturated using Soft-Core obturators (Kerr, Romulus, Mi, USA), while Group TH canals (n= 20) were obturated using Thermafil Endodontic Obturators (Tulsa Dental Products, Tulsa, OK, USA), strictly following manufacturers' instructions for use. The obturations were analyzed by means of CBCT to measure the distance from the apical limit of obturation to the apical foramen and the presence of voids inside root canals. RESULTS: There was no significant difference between the two groups in the mean distance of the apical extent of the obturation (t test, p>0.05). Overfilling occurred in only 3 cases (2 in Group TH and 1 in Group SC). The percentages of voids in both groups were very low with no significant difference (Z test, p>0.05). CONCLUSIONS: The two tested CBO techniques showed similar positive results in terms of performance, even if, after checking with verifiers, in most cases the size of the selected Soft-Core obturator was one size smaller than Thermafil.

Incidence of Deformation and Fracture of Twisted File Adaptive Instruments after Repeated Clinical Use.

OBJECTIVES: The aim of the present study was to investigate the incidence of deformation and fracture of twisted file adaptive nickel-titanium instruments after repeated clinical use and to identify and check whether the three instruments within the small/medium sequence showed similar or different visible signs of metal fatigue. MATERIAL AND METHODS: One-hundred twenty twisted file adaptive (TFA) packs were collected after clinically used to prepare three molars and were inspected for deformations and fracture. RESULTS: The overall incidence of deformation was 22.2%, which was not evenly distributed within the instruments: 15% for small/medium (SM)1 (n = 18), 38.33% for SM2 (n = 46) and 13.33% for the SM3 instruments (n = 16). The defect rate of SM2 instruments was statistically higher than the other two (P < 0.001). The fracture rate was 0.83% (n = 3), being two SM2 instruments and one SM3. CONCLUSIONS: It was observed a very low defect rate after clinical use of twisted file adaptive rotary instruments. The untwisting of flutes was significantly more frequent than fracture, which might act as prevention for breakage. The results highlight the fact that clinicians should be aware that instruments within a sequence might be differently subjected to intracanal stress.

Cutting efficiency of nickel-titanium rotary and reciprocating instruments after prolonged use.

The aim of the present study was to compare the cutting efficiency of Twisted File instruments used in continuous rotation or TF Adaptive motion and evaluate if prolonged use significantly affected their cutting ability. 20 new NiTi instruments were used in the present study (TF tip size 35, 0.06 taper; Sybron-Endo, Orange, CA, USA), divided into 2 subgroups of 10 instruments each, depending on which movement was selected on the endodontic motor. Group 1: TF instruments were activated using the program TF continuous rotation at 500 rpm and torque set at 2 N; Group 2: TF instruments were activated using the reciprocating TF Adaptive motion. Cutting efficiency was tested in a device developed to test the cutting ability of endodontic instruments. Each instrument cut 10 plastic blocks (10 uses) and the length of the surface cut in a plastic block after 1 min was measured in a computerized program with a precision of 0.1 mm. Maximum penetration depth was calculated after 1 use and after 10 uses, and mean and standard deviation (SD) of each group was calculated. Data were statistically analyzed with a one-way ANOVA test (P < 0.05). TF instruments used in continuous rotation (Group 1) cut a mean depth of 10.4 mm (SD = 0.6 mm) after the first use and 10.1 mm (SD 1.1 mm) after 10 uses, while TF instruments used with the Adaptive motion cut a mean depth of 9.9 mm (SD = 0.7 mm) after the first use and 9.6 mm (SD = 0.9 mm) after 10 uses. There was no statistically significant difference between the two groups investigated (P > 0.05) nor between instruments after 1 or 10 uses. In conclusion, the TFA motion showed a lateral cutting ability similar to continuous rotation and all tested instruments exhibited the same cutting ability after prolonged use.

Deformations and cyclic fatigue resistance of nickel-titanium instruments inside a sequence.

AIM: To compare the effect of brushing motion on torsional and cyclic fatigue resistance of TF Adaptive instruments after clinical use. METHODS: 20 packs of TFA small sequence (SybronEndo, Orange, CA, USA) were used for this study and divided into two groups. Each instrument prepared one resin tooth, consisting in 4 canals with a complex anatomy. In group A, no brushing motion was performed. In group B, after the green instrument reached the working length, brushing motion with circumferential filing was performed for 15 seconds in each canal (overall 1 minute). All the instruments were then subjected to cyclic fatigue test and mean values and standard deviation for time to fracture were evaluated. Data were subjected to one-way analysis of variance and Bonferroni t-test procedure with a significance set at P < 0.05. RESULTS: No instruments were broken during preparation of root canals. Two TF Adaptive green and 5 yellow showed unwinding after intracanal clinical use. No statistically significant differences were found between green instruments of both groups (P > 0.05), while a statistically significant difference was found between the yellow instruments (P < 0.05), with group B showing an higher resistance to cyclic fatigue. CONCLUSIONS: A prolonged passive brushing motion did not adversely affected mechanical resistance of the instrument used for this purpose. Resistance to both deformations and cyclic fatigue of the second instrument within the TFA small sequence was enhanced by the coronal flaring provided by the brushing action of the first instrument used.

Cutting efficiency of instruments with different movements: a comparative study.

OBJECTIVES: The aim of the present study was to evaluate the cutting efficiency of two new reciprocating instruments, Twisted File Adaptive and WaveOne Primary. MATERIAL AND METHODS: 10 new Twisted File Adaptive (TF Adaptive) (SybronEndo, Glendora, CA, USA) and 10 new WaveOne Primary files (Dentsply Maillefer, Ballaigues, Switzerland) were activated using a torque-controlled motor, respectively TFA motor (SybronEndo, Glendora, CA, USA) and Silver motor (VDW, Munich, Germany). The device used for the cutting test consisted on a mainframe to which a mobile plastic support for the hand-piece is connected and a stainless-steel block containing a Plexiglas block against which the cutting efficiency of the instruments was tested. The length of the block cut in 1 minute was measured in a computerized program with a precision of 0.1 mm. Mean and standard deviations of each group were calculated and data were statistically analyzed with one-way ANOVA and Bonferroni t test (P < 0.05). RESULTS: TF Adaptive displayed significantly greater maximum penetration depth than WaveOne Primary (P < 0.05). In fact, TF Adaptive instruments (Group 1) cut the Plexiglas block to a mean depth of 8.7 (SD 0.5) mm, while WaveOne Primary instruments cut the Plexiglas block to a mean depth of 6.4 (SD 0.3) mm. CONCLUSIONS: Twisted File Adaptive instruments demonstrated statistically higher cutting efficiency than WaveOne instruments.

Cyclic fatigue of instruments for endodontic glide path.

Endodontic glide path is the creation of a smooth patency from canal orifice to apex, which can be performed manually or with small tapered NiTi rotary instruments. The use of stainless steel (SS) hand K-files inserted in a reciprocating handpiece can be a possible alternative to create a mechanical glide path. The aim of this study was to compare the cyclic fatigue resistance between SS K-files used in a reciprocating motion and NiTi rotary instruments in artificial curved canals. Ten SS size 15 K-files used with the M4 handpiece (SybronEndo, Glendora, CA, USA) and ten PathFiles (Maillefer-Dentsply, Ballaigues, CH, Switzerland) NiTi rotary instruments size 16, 0.02 taper were tested for resistance to cyclic fatigue. The time to fracture inside an artificial curved canal was recorded for each instrument. Data were analyzed by one-way ANOVA and Tukey HSD test. Mean time (and SD) to failure was 464 s (±40.4) for the Group PF (NiTi rotary PathFile), and 1049 s (±24.8) for the Group M4 (SS K-files reciprocating) with a statistically significant difference between the two groups (p = 0.033). The SS 15 K-files used with the M4 handpiece showed a significant greater resistance to cyclic fatigue when compared to the NiTi rotary PathFiles. Therefore, the use of small size SS files in a reciprocating motion might be a rational choice for the creation of a mechanical endodontic glide path in curved root canals.

Geometric analysis of maxillary first premolar prepared by two nickel-titanium rotary instruments.

AIM: The present study was conducted with the aim of evaluating and comparing the shaping ability of two Nickel-titanium rotary instruments, with two disparate design features, on root canal geometry of extracted human maxillary first premolars using microcomputed tomography. STUDY DESIGN: Twenty four bifurcated maxillary first premolars were divided into two groups and embedded in a rubber-based impression material. Both groups were submitted to micro-computed tomography before and after canal preparation (buccal and palatal) with either ProFile Vortex or Revo-S rotary instruments. Images were reconstructed and cross-sections corresponding to a distance 1, 2, 3, 4, 5, 6, and 7 mm from the anatomical apex were selected for canal transportation analysis. Volume changes were also measured. RESULTS: The degree and direction of canal transportation were non-significant for both instruments. Statistically significant differences were observed only between levels in the buccal canal in both groups. There was no significant difference between the two rotary systems in regards to the volume of dentin removed. CONCLUSION: Our findings showed that ProFile Vortex and Revo-S instruments respected the original root canal anatomy and behaved similarly. ProFile Vortex rotary systems produced with innovative process were concluded to shape the upper maxillary premolar by leading minimal canal transportation, similar to Revo-S, rotary systems produced from traditional process.

A new device to test cutting efficiency of mechanical endodontic instruments.

BACKGROUND: The purpose of the present study was to introduce a new device specifically designed to evaluate the cutting efficiency of mechanically driven endodontic instruments. MATERIAL AND METHODS: Twenty new Reciproc R25 (VDW, Munich, Germany) files were used to be investigated in the new device developed to test the cutting ability of endodontic instruments. The device consists of a main frame to which a mobile plastic support for the hand-piece is connected and a stainless-steel block containing a Plexiglas block against which the cutting efficiency of the instruments was tested. The length of the block cut in 1 minute was measured in a computerized program with a precision of 0.1mm. The instruments were activated by using a torque-controlled motor (Silver Reciproc; VDW, Munich, Germany) in a reciprocating movement by the "Reciproc ALL" program (Group 1) and in counter-clockwise rotation at 300 rpm (Group 2). Mean and standard deviations of each group were calculated and data were statistically analyzed with a one-way ANOVA test (P<0.05). RESULTS: Reciproc in reciprocation (Group 1) mean cut in the Plexiglas block was 8.6 mm (SD=0.6 mm), while Reciproc in rotation mean cut was 8.9 mm (SD=0.7 mm). There was no statistically significant difference between the 2 groups investigated (P>0.05). CONCLUSIONS: The cutting testing device evaluated in the present study was reliable and easy to use and may be effectively used to test cutting efficiency of both rotary and reciprocating mechanical endodontic instruments.

Fatigue resistance of rotary instruments manufactured using different nickel-titanium alloys: a comparative study.

The aim of this study was to investigate whether cyclic fatigue resistance is increased for Controlled Memory (CM) Nickel-Titanium (NiTi) instruments, compared to instruments produced using traditional NiTi and instruments produced using M-Wire alloy. Two groups of NiTi endodontic instruments consisting of identical instrument sizes (constant 0.06 taper and 0.25 tip diameter and constant 0.04 taper and 0.40 tip diameter) were tested: group A compared Hyflex™ CM, Vortex ™ and ProFile ™ size 25 and 0.06 taper and group B compared Hyflex™ CM, Vortex™ and ProFile™ size 40 and 0.04 taper. 10 files from each different subgroup were tested for cyclic fatigue resistance. Mean and standard deviations of the Number of Cycles to Failure (NCF) were calculated for each group and data were statistically analysed (p < 0.05). Hyflex™ CM instruments, size 25 and 0.06 taper, and size 40 and 0.04 taper, showed a significant increase in the mean number of cycles to failure when compared with size 25 and 0.06 taper Vortex™ and ProFile™. No statistically significant difference (p > 0.05) was noted between Vortex™ and ProFile™ in the tested sizes. The new manufacturing process involving memory shape heat treatment produced new NiTi rotary files (Hyflex™ CM) significantly more resistant to fatigue than instruments produced with other proprietary methods of treatment (Vortex™) and with the traditional NiTi grinding process (ProFile™).

The influence of different angles and reciprocation on the shaping ability of two nickel-titanium rotary root canal instruments.

PURPOSE: The purpose of the present study was to investigate and compare the effect of different reciprocating movements and angles on the shaping ability of the WaveOne and the single-fle ProTaper F2 using cone beam computed tomography (CBCT). MATERIALS AND METHODS: The mesiobuccal canals of 40 extracted maxillary molars, with curvatures of 20 to 45° were coded and randomly divided into 4 equal experimental groups according to the instrument used (ProTaper F2 fle and Wa-veOne) and the reciprocation range, for both instruments, a 150° angle was used for cutting and a 30° angle was used for release. Group 1 - WaveOne primary 150° CCW rotation angle and 30° CW rotation angle; Group 2 - WaveOne 90° CCW rotation angle and 30° CW rotation angle; Group 3 - ProTaper F2 150° CW rotation angle and 30° CCW rotation angle; Group 4 - ProTaper F2 90° CW rotation angle and 30° CCW rotation angle. Canals were scanned before and after preparation using CBCT to evaluate the volumetric change, canal transportation and the canal centering ability at 2.6, 5.2 and 7.8 mm from the apex. The mean ± standard deviation (SD) values were analyzed, and the significance level was set at p ≤ 0.05. RESULTS: There was no significant difference in the amount of dentin removed among the experimental groups, except that WaveOne 150°CCW 30°CW significantly showed the least volume of dentin removed (0.40 ± 0.9) at 7.8 mm. All rotary systems tested in the different groups resulted in canal transportation in different directions at all examined levels. WaveOne 150°CCW 30°CW, demonstrated the lowest mean value of root canal transportation in both the mesial and furcal directions and in both the coronal and apical directions compared to the other groups. At the 7.8 level, WaveOne 150°CCW 30°CW yielded the highest mean centering ratio, whereas ProTaper F2 CW 150° CCW 30° yielded the lowest, statistically significant at p ≤ 0.05. CONCLUSION: The results of the present study demonstrated that differences among various reciprocating motions and angles could affect the shaping ability of a single-fle Nickel-titanium (NiTi) instrument.

Topographic Analysis of HyFlex(®) Controlled Memory Nickel-Titanium Files.

BACKGROUND: The multiple uses of HyFlex(®) controlled memory (CM) rotary instruments (Coltene-Whaledent, Allstetten, Switzerland) have been recommended after sterilization. The purpose of this study was to analyze the surface defects on HyFlex(®) instruments after use and to determine their ability to return to their original shape after autoclaving. MATERIALS AND METHODS: Twenty-four new HyFlex(®) files were scanned using micro-computed tomography before the initial use, after use until defects were visible and after autoclaving. Surface analysis was performed on each file to determine the changes in the files after deformation; defects were recorded as unwinding and curving. These changes were categorized according to the severity, and the initial and final scans of the files were superimposed to illustrate the recovery of the files to their original shape. The data were analyzed using Chi-square and t-test. RESULTS: The t-test of Student's Newman-Keuls revealed a significant difference (P < 0.05) between unused and used files, almost all files exhibited visible defects without fractures, including unwinding and curving associated with unwinding. The most frequently observed defect was unwinding of the spirals (100%), whereas curving associated with unwinding was infrequently observed. A Chi-square test showed that the deformation (curve: P = 0.000, and unwinding: P = 0.011, incidence depended on the size of the files. The greatest frequency of curving occurred in the small files #20/0.04 and #20/0.06, the difference was statistically significant from all file sizes (P < 0.05). The majority of the files (79%) were able to restore the unwinding and regain their original shape after autoclaving. The highest rate of unrestored files was observed on #20/0.04 and #20/0.06 instruments, and the difference was statistically significant from all file sizes (P < 0.05). CONCLUSION: HyFlex(®) CM nickel-titanium files appear to regain their original shape after sterilization.

Professional attitudes and behaviors acquired during undergraduate education in the College of Dentistry, King Saud University.

OBJECTIVES: The purpose of the study was to investigate and evaluate the professional attitudes and behaviors acquired by students and recently graduated dentists during undergraduate education at King Saud University. METHODS: This cross-sectional survey used a 27-item questionnaire covering four cumulative theoretical dimensions of professionalism. Questionnaires were distributed to fifth-year students, interns, and demonstrators in the College of Dentistry during the academic year 2010-2011, and 203 completed questionnaires were used in analyses. Descriptive statistics were used to summarize responses. Crosstab and chi-squared tests were used, with statistical significance set at P < 0.05. RESULTS: The response rate was 79.3% (43.6% of males, 94% of females). Eighty-seven questionnaires were collected from fifth-year students, 92 from interns, and 24 from demonstrators. Many (59%) participants demonstrated high levels of professional attitudes and behaviors, whereas 40% did not comply with the elements of professionalism. Analyses revealed highly significant differences in certain responses with regard to gender, academic level, and grade point average. CONCLUSIONS: Although some participants did not possess all professional qualities, all participants possessed at least some elements of professionalism measured in this study. We thus recommend a strategic effort to develop targeted plans emphasizing professionalism at all levels of the dental school curriculum. High-profile role modeling, lectures, seminars, and academic ceremonies are ways of achieving professional development among dental students in parallel with their acquisition of basic scientific knowledge and clinical skills. This approach will formally and informally communicate that professionalism is a core value.

Microcomputed tomographic analysis of the furcation grooves of maxillary first premolars.

OBJECTIVES: The aims of this study were to conduct a morphometric analysis on the buccal furcation grooves in freshly extracted bifurcated maxillary first premolars (MFPs) and to correlate all anatomical measurements using microcomputed tomography. MATERIALS AND METHODS: Twenty-three human MFPs with bifurcated canals were selected for this study. The specimens were analyzed with microcomputed tomography. The length, the beginning, and the ending of the grooves were measured. The minimum cross-sectional canal wall thickness in the grooves was located, and the width of the dentin thickness was calculated. All measurements were recorded and statistically analyzed. RESULTS: The concavity of the grooves begins before the bifurcation site in 9/23 samples and after the bifurcation in 56.5% of samples. The groove length varied between 1.1-9 mm; the cross-sectional area with minimum palatal dentin thickness was 0.78±0.14 mm, which was located at a mean distance of 7.1 mm from the cementoenamel junction (CEJ) and 1.38 mm from the furcation. CONCLUSIONS: The presence of the furcation grooves in the palatal aspects of the buccal roots of the MFPs was 100%. The length, depth, location, and width of the dentin thickness of the grooves varied in relation to tooth length, bifurcation, and CEJ. These parameters should be taken into consideration before any endodontic or restorative procedures are performed. Reducing dentin width too vigorously by intracanal instrumentation can predispose to vertical root fractures or perforations; if a post cannot be avoided, it should not extend 6.5 mm from the CEJ.

Influence of file motion on cyclic fatigue of new nickel titanium instruments.

AIM: The aim of the present study was to compare the resistance to cyclic fatigue of Hyflex® (Coltene-Whaledent, Allstatten, Switzerland) size 40 taper.04 nickel titanium instruments used in continuous rotation versus the use with a reciprocating motion. The null hypothesis was that different file motions had no influence on the lifetime of instruments subjected to a cyclic fatigue test. METHODOLOGY: 24 Hyflex® size 40 taper.04 nickel titanium instruments were randomly divided in two groups (n=12 each), and submitted to a cyclic fatigue test. The first group (CR group) were used with a continuous rotation, while the second one (RCP group) with a reciprocating motion. The cyclic fatigue tests were performed by using a stainless steel block containing an artificial canal shaped with a 135° angle. All instruments were rotated or reciprocated until fracture occurred. The time to fracture was recorded visually with a 1/100 second chronometer. Data were recorded and statistically analysed. RESULTS: Results indicated that instruments used with a reciprocating motion showed a significant increase in the meantime to failure when compared to those used in continuous rotation. CONCLUSIONS: The null hypothesis was rejected. Results of the present study showed that reciprocating motion extended resistance to cyclic fatigue of the tested nickel titanium instruments, when compared to continuous rotation.

The influence of three different instrumentation techniques on the incidence of postoperative pain after endodontic treatment.

AIMS: Apical extrusion of infected debris to the periradicular tissues is one of the principal causes of postoperative pain and discomfort. Recent researches have shown that reciprocating instrumentation techniques seem to significantly increase the amount of debris extruded beyond the apex and, consequently, the risk of postoperative pain. The goal of the present study was to evaluate and compare postoperative pain using three different nickel-titanium instrumentation techniques: a rotary crown-down technique using TF instruments (SybronEndo, Orange, Ca), a reciprocating single-file technique using WaveOne instruments (Maillefer DEntsply, Baillagues, CH), and a novel instrumentation technique (TF Adaptive, SybronEndo, Orange, Ca), using a unique, proprietary movement, combining reciprocation and continuous rotation. METHODS: Ninety patients requiring endodontic treatment on permanent premolar and molar teeth with non vital pulps preoperatively were included in the study. The patients were assigned into three groups of 30 patients each, trying to make the groups very similar, concerning the number of root canals, presence of initial pain and periapical lesions. The teeth in group 1 (n = 30) were instrumented with a crown-down technique using TF instruments, whilst those in group 2 (n = 30) were instrumented with a single-file technique using Waveone 08 25. The third group (n = 30) used the 3-file Tf Adaprtive sequence. All techniques were performed following manufacturers' instructions and all canals were shaped, cleaned and obturated in a single-visit by the same operator. The assessment of postoperative pain was carried out at 3 days by using a visual analogue scale. VAS pain scores were compared using one-way ANOVA post hoc Tukey test. A value of p < 0.05 was required for statistical significance. RESULTS: Results for VAS pain scores showed a statistically significant difference was found between the WaveOne (p=0,021) technique and the other two techniques. No statistical significant differences were found between TF and TF Adaptive (p= 0,087). When evaluating patient experiencing sever pain the incidence of symptoms was significantly higher with the WaveOne technique. CONCLUSIONS: Since the incidence of preoperative pain, the type of tooth and the pulp and periodontal pathology were quite similar between the three tested groups, and all the other variables (operator, irrigation, obturation) were identical, we may conclude that the difference in postoperative pain can be mainly related to the different instrumentation techniques.

Mechanical resistance of carbon and stainless steel hand instruments used in a reciprocating handpiece.

AIM: The manual files are still widely used for initial canal negotiation prior the use of nickel-titanium shaping instruments, to determine working length and to verify patency. A mechanical glide path can be performed using manual files with handpieces, such as M4 Handpiece (SybronEndo, USA) that allows a 30°/30° reciprocating motion. The Pathfinders (SybronEndo, USA) are hand files designed to negotiate complex canals, made from stainless steel (SS) or carbon steel (CS) alloys. The aim of this in vitro study was to compare cyclic fatigue resistance of these two different types of manual Pathfinder instruments used in a M4 reciprocating handpiece in double curved artificial canals. MATERIALS AND METHODS: Manual instruments designed for glide path (size #9 ISO .02 taper) made from different alloys were selected: Group SS -stainless steel Pathfinders (Sybron Endo) and Group CS - carbon steel Pathfinders size K2 (Sybron Endo). Ten instruments of each group were tested for resistance to cyclic fatigue with a reciprocating M4 handpiece inside an artificial S-shaped canal; the time to fracture was recorded for each file and data were statistically analyzed (ANOVA). RESULTS: Mean values (and SD) were 527 (± 89) seconds for the CS instruments and 548 (± 104) seconds for the SS files. No significant differences were observed between groups (p=0,062). CONCLUSIONS: According to the results, both carbon and stainless steel instruments presented similar fatigue resistance when used with M4 reciprocating handpiece in double curved canals.