Vulnerability of Thermal Energy Storage Lining Material to Erosion Induced by Particulate Flow in Concentrated Solar Power Tower Systems.

Researchers from all around the world have been paying close attention to particle-based power tower technologies. On the King Saud University campus in the Kingdom of Saudi Arabia, the first integrated gas turbine-solar particle heating hybrid system has been realized. In this study, two different types of experiments were carried out to examine how susceptible prospective liner materials for thermal energy storage tanks were to erosion. An accelerated direct-impact test with high particulate temperature was the first experiment. A low-velocity mass-flow test was the second experiment, and it closely mimicked the flow circumstances in a real thermal energy storage tank. The tests were conducted on bare insulating fire bricks (IFBs) and IFBs coated with Tuffcrete 47, Matrigun 25 ACX, and Tuffcrete 60 M. The latter three lining materials were high-temperature-resilient materials made by Allied Mineral Products Inc. (AMP) (Columbus, OH, USA). The results showed that although IFBs coated with AMP materials worked well in this test, the accelerated direct-impact test significantly reduced the bulk of the bare IFB. As a result, lining substances must be added to the surface of IFBs to increase their strength and protection because they cannot be used in situations where particles directly impact their surface. On the other hand, the findings of the 60 h cold-particle mass-flow test revealed that the IFBs were not significantly eroded. Additionally, it was discovered that the degree of erosion on the samples of bare IFB was unaffected by the height of the particle bed.

Experimental Investigation on the Energy and Exergy Efficiency of the Vacuum Membrane Distillation System with Its Various Configurations.

This paper addresses a retrofitting vacuum membrane distillation (VMD) setup to reduce the accumulated pressure inside the permeated side. This modification is necessary to extend the operation of the VMD to extreme operation conditions of higher hot water temperatures. This modification, denoted as a hybrid configuration, proposes the injection of a cold water stream into the VMD cell without mixing it with the permeate. Energy and exergy efficiency analyses were performed to assess the effectiveness of the hybrid configuration. The performance of the modified system indicated an improvement in terms of permeate flux (J), the gain output ratio (GOR), and the utilitarian exergetic efficiency (ηex,u), which reach up to two and three times that of the base configuration of the VMD system. However, the exergetic efficiency (ηex) of the hybrid system showed marginal improvement compared to the base case over the tested range of hot water temperatures. This is because the enhanced vapor production is penalized by excess energy consumption. Moreover, the highest exergy destruction percentages occurred in the operational components (e.g., heater and chillers) which fall in the range of 19.0-68.9%. The exergy destruction percentage in the original components (e.g., the VMD cell and condenser) did not exceed 8.3%. Furthermore, this study indicated that the hybrid configuration requires additional tuning and optimization to perform efficiently over wide operating conditions.

Performance Comparison of Cross- and Forward-Flow Configurations for Multiple-Effect Vacuum Membrane Distillation.

This work addresses retrofitting the infrastructure of multiple-effect vacuum membrane distillation (V-MEMD) units by using cross-flow configuration (CFC). In this configuration, the feed water is evenly divided and distributed over the effects. In this case, the feed water stream for each effect is kept at a high temperature and low flow rate. This will lead to an increase in the vapor pressure gradient across the hydrophobic membrane and can also maintain the thermal energy of the stream inside the individual effect. It is found that CFC improves internal and global performance indicators of productivity, energy, and exergy. A mathematical model was used to investigate the performance of such a modification as compared to the forward-flow configuration (FFC). The cross-flow configuration led to a clear improvement in the internal performance indicators of the V-MEMD unit, where specifically the mass flux, recovery ratio, gain output ratio, and heat recovery factor were increased by 2 to 3 folds. Moreover, all the global performance indicators were also enhanced by almost 2 folds, except for the performance indicators related to the heat pump, which is used to cool the cold water during the operation of the V-MEMD unit. For the heat pump system, the specific electrical energy consumption, SEEC, and the exergy destruction percentage, Ψdes, under the best-operating conditions, were inferior when the feed water flow was less than 159 L/h. This can be attributed to the fact that the heat rejected from the heat pump system is not fully harnessed.

Characterization of Low-Cost Particulates Used as Energy Storage and Heat-Transfer Medium in Concentrated Solar Power Systems.

Utilizing solid particles as a heat-transfer medium in concentrated solar power applications has gained growing attention lately. Unlike molten salts, solid particles offer many benefits, which include: high operating temperatures (greater than 1000 °C), a lack of freezing issues and corrosivity, abundant availability, high thermal energy storage capacity, a low cost, and applicability in direct irradiation. Comprehensive knowledge of thermophysical and optical properties of solid particles is essential to ensure an effective harnessing of solar energy. The most important considerations when selecting solid particles include: thermophysical and optical properties, thermal resistance, crack resistance, satisfactory health and safety risks, availability, and low cost. It is also imperative to consider optical and thermophysical characteristics that might change from what they were "as received" after cyclic heating for a long period. Therefore, the knowledge of thermal performance of particulate materials becomes significant before using them as a heat-transfer medium. In this study, some particulate materials were chosen to study their feasibilities as heat-transfer and storage media for a particle-based central receiver tower system. These particulate materials included white sand, red sand, ilmenite, and Carbobead CP. The candidate particulate materials were heated at high temperatures for 6 h and then cooled to room temperature. After that, cyclic heating was performed on the particulate materials for 500 h at 1200 °C. The optical properties were represented by weighted solar absorptance, and the thermophysical properties of the particulates were measured "as received" and after cyclic heating (aging). EDX and XRD were conducted to quantify the chemical composition and interpret the changes in appearance associated with the particulate materials after cyclic heating. The results showed a considerable agglomeration in all particulates except for white sand in the 6 h heating test, and high agglomeration in the ilmenite. A slight decrease in the optical properties in the white sand and Carbobead CP was found after the aging test. The specific heat was decreased for red and white sand. The EDX and XRD results for white sand and Carbobead CP showed chemical stability, indicating high durability and reliability.