Bond Strength of Resin Cement and Glass Ionomer to Nd:YAG Laser-Treated Zirconia Ceramics.

PURPOSE: To investigate the effect of neodymium-doped yttrium aluminum garnet (Nd:YAG) laser irradiation on the surface properties and bond strength of zirconia ceramics. MATERIALS AND METHODS: Forty-eight zirconia ceramic pieces (4 × 4 × 1 mm3 ) were divided into four groups according to surface treatment as follows: two control groups (no treatment) for resin bonding (CRC) and glass ionomer (GI) bonding (CGC); two laser treatment groups (Nd:YAG irradiation, 3 W, 200 MJ, 10 Hz, 180 µs) for resin bonding (LRC) and GI bonding (LGC). The ceramics in the control groups and the laser groups were distinguished by the application of different cements (resin cement and GI). Following surface treatments, the specimens were cemented to human dentin with resin cement and GI. After bonding, the shear bond strength (SBS) of the ceramic to dentin was measured, and the failure mode of each specimen was analyzed using a stereomicroscope. A one-way ANOVA compared the average bond strength of the four groups. Pairwise comparisons among the groups were performed using the Games-Howell test. The level of significance was set at 0.05. RESULTS: The means (± standard deviation) of SBS values in the CRC, CGC, LRC, and LGC groups were 3.98 ± 1.10, 1.66 ± 0.59, 10.24 ± 2.46, and 2.21 ± 0.38 MPa, respectively. Data showed that the application of the Nd:YAG laser resulted in a significantly greater SBS of the resin cement to the zirconia ceramics (p < 0.001). The highest bond strength was recorded in the LRC group. In the CRC group, 75% of the failures were of the adhesive type, compared with 66.7% and 83.3% in the LRC and LGC groups, respectively. In the CGC group, all failures were adhesive. CONCLUSIONS: Pretreatment of zirconia ceramic via Nd:YAG laser improves the bond strength of the resin cement to the zirconia ceramic. GI cement does not provide sufficient bond strength of zirconia ceramics to dentin.

Effect of Molding Technique on Iwo Physical Properties of Acrylic Resin Specimens.

The aim of this study was to compare dimensional changes and flexural strength of specimens processed by conventional and injection-molding techniques. SR-Ivocap Triplex Hot Resin was used for conventional pressure-packed, and SR-Ivocap High Impact was used for injection-molding techniques. Measurements were recorded at 24-hour, 48-hour and 12-day intervals. Three-point test and statistical analysis were carried out. After each water storage period, the acrylic specimens produced by injection method exhibited less dimensional change compared to those produced by the conventional technique. Within the limitation of this study, dimensional changes and flexural strength of acrylic resin specimens were influenced by molding technique, and the SR-Ivocap injection procedure exhibited higher dimensional accuracy and flexural strength compared to conventional molding.

Effect of denture cleansers on color stability and surface roughness of denture base acrylic resin.

BACKGROUND: Color stability of acrylic resin is one of the most important feature for denture wearers. Many patients use detergent solutions to remove denture stains. The purpose of this study was to evaluate color stability and surface roughness of two common acrylic resins in different detergent and tea solutions. MATERIALS AND METHODS: 112 acrylic resin blocks of Meliodent and Acropars (each 56 blocks) were divided into seven groups of different treatment: 1% sodium hypochlorite for 10 min a day for 1 month (H10m), 1% sodium hypochlorite for 8 hours a day for 1 week (H&h), Correga tabs solution for 8 hours a day for 1 month (C&H), tea bag for 2 hours a day for 1 month (T2 h), tea bag for 2 hours a day then 10 min in 1% sodium hypochlorite for 1 month (T-H), tea bag for 2 hours then 8 hours in the Correga tab solution a day for 1 month (T-C), and finally distilled water for 1 month as a control group (con). After specimen's treatment, color (CIE Lab) and surface roughness (Ra, µm) of samples were measured. The results were analyzed by analysis of variance (ANOVA), followed by Tukey's HSD and Dunnett T3. RESULTS: Group T2h exhibited a significant (P<;0.05) color change and control specimens exhibited the lowest color change. Sodium hypochlorite caused a significant (P<0.05) color change in the Acropars group in comparison with the Meliodent group. In the Correga tab solution the difference was not significant (P=0.155). There was a significant (P<0.05) color change in the T-H treatment. The Acropars and Meliodent acrylic resin did not a show significant difference in surface roughness after different treatments. CONCLUSION: Sodium hypochlorite 1% for 10 minutes a day in a month is the recommended hygiene protocol. The color stability of acryl is brand-type dependent but surface roughness is not.

Flexural strength of acrylic resin denture bases processed by two different methods.

Background and aims. The aim of this study was to compare flexural strength of specimens processed by conventional and injection-molding techniques. Materials and methods. Conventional pressure-packed PMMA was used for conventional pressure-packed and injection-molded PMMA was used for injection-molding techniques. After processing, 15 specimens were stored in distilled water at room temperature until measured. Three-point flexural strength test was carried out. Statistical analysis was carried out by SPSS using t-test. Statistical significance was defined at P<0.05. Results. Flexural strength of injection-polymerized acrylic resin specimens was higher than that of the conventional method (P=0.006). This difference was statistically significant (P=0.006). Conclusion. Within the limitations of this study, flexural strength of acrylic resin specimens was influenced by the molding technique.

Dimensional changes of acrylic resin denture bases: conventional versus injection-molding technique.

OBJECTIVE: Acrylic resin denture bases undergo dimensional changes during polymerization. Injection molding techniques are reported to reduce these changes and thereby improve physical properties of denture bases. The aim of this study was to compare dimensional changes of specimens processed by conventional and injection-molding techniques. MATERIALS AND METHODS: SR-Ivocap Triplex Hot resin was used for conventional pressure-packed and SR-Ivocap High Impact was used for injection-molding techniques. After processing, all the specimens were stored in distilled water at room temperature until measured. For dimensional accuracy evaluation, measurements were recorded at 24-hour, 48-hour and 12-day intervals using a digital caliper with an accuracy of 0.01 mm. Statistical analysis was carried out by SPSS (SPSS Inc., Chicago, IL, USA) using t-test and repeated-measures ANOVA. Statistical significance was defined at P<0.05. RESULTS: After each water storage period, the acrylic specimens produced by injection exhibited less dimensional changes compared to those produced by the conventional technique. Curing shrinkage was compensated by water sorption with an increase in water storage time decreasing dimensional changes. CONCLUSION: Within the limitations of this study, dimensional changes of acrylic resin specimens were influenced by the molding technique used and SR-Ivocap injection procedure exhibited higher dimensional accuracy compared to conventional molding.

Maximum dislodging forces of mandibular implant-assisted removable partial dentures: in vitro assessment.

PURPOSE: The initial retention of implant-assisted removable partial dentures (IARPDs) is unknown. The purpose of this in vitro study was to compare maximum dislodging forces of distal extension mandibular IARPD with two different attachments and three clasp designs. MATERIALS AND METHODS: A simulated class I partially edentulous mandible was prepared with two screw-type 3.75 × 12 mm implants in the first molar regions and 2 metal-ceramic crowns on distal abutments. Fifteen bilateral distal extension frameworks were conventionally fabricated in three clasp designs (suprabulge, infrabulge, no clasp). Locator attachments were connected to the 15 denture bases with autopolymerized resin. Each specimen was subject to four types of retention pulls (main, anterior, posterior, unilateral pull) five times with a universal testing machine. Locator attachments were replaced with O-ring attachments, and the same procedure was performed. Therefore, the study groups included: IRPD with Locator attachment and suprabulge clasp (group 1), IRPD with Locator attachment and infrabulge clasp (group 2), IRPD with Locator attachment and no clasp (group 3), IRPD with O-ring attachment and suprabulge clasp (group 4), IRPD with O-ring attachment and infrabulge clasp (group 5), IRPD with O-ring attachment and no clasp (group 6). Data were analyzed using one-way ANOVA, two-way ANOVA, and Tukey tests. RESULTS: The highest mean value was 22.99 lb for prostheses with a Locator attachment and suprabulge clasp. The lowest retentive values were recorded for IARPDs with O-ring attachments. CONCLUSION: The results of this in vitro study suggest that the precise selection of attachments with or without clasp assemblies may affect the clinical success of mandibular IARPDs.

The microbiology of the peri-implant sulcus following successful implantation of oral prosthetic treatments.

BACKGROUND: Oral implants are widely used in partially and fully edentulous patients; however, the integration of an implant can be endangered by factors such as intraoral bacteria or inflammatory reactions. The purpose of this study was to evaluate the microbial flora present in the sulcus around dental implants and to assess the relationship between gingival health and microbial flora present. MATERIALS AND METHODS: Twenty patients who had received oral implants with no complications were followed for a period of 9 months. Assessment of probing depth, the presence of bleeding on probing and microbial sampling from the peri-implant sulcus were performed at three different time points- 4 weeks after surgery, 1 month and 6 months after loading. The samples were taken by paper points and transferred to the microbiology lab in thioglyocolate cultures. In order to do a colony count and isolate the aerobic capnophilic and anerobic bacteria the samples were cultured and incubated on laboratory media. The colonies were also identified using various diagnostic tests. Alterations in the presence of various bacterial species over time and gum health were tested using analysis of variance (ANOVA) with Tukey's test post hoc. RESULTS: The average pocket depth for each patient ranged from 1.37 ± 0.39 mm to 2.55 ± 0.72 mm. The bacteria isolated from the cultured samples included aerobic, facultative anerobic, obligate anerobic and capnophilic bacteria. CONCLUSION: The anerobic conditions created in the peri-implant sulcus might with time enhance the number of anerobic bacteria present following dental implant loading.