Corrosion of Stainless Steel in Simulated Nuclear Reactor Primary Coolant-Experiments and Modeling.

In the present paper, the effect of the evolution of primary water chemistry during power operation on the corrosion rate and conduction mechanism of oxide films on stainless steel is studied by in situ impedance spectroscopy at 300 °C/9 MPa during 1-week exposure periods in an autoclave connected to a recirculation loop. At the end of the exposure period, the samples were anodically polarized in a wide range of potentials to evaluate the stability of the passive oxide. Separate samples of the same steel were simultaneously exposed to the coolant and subsequently analyzed by glow discharge optical emission spectroscopy (GDOES) in order to estimate the thickness and the in-depth composition of the formed oxides. Impedance data were quantitatively interpreted using the mixed-conduction model for oxide films (MCM) to estimate the rates of metal oxidation at the alloy/oxide interface, oxide dissolution and restructuring at the film/coolant interface, and ion transport in the protective corrosion layer.

Design of Laser Activated Antimicrobial Porous Tricalcium Phosphate-Hydroxyapatite Scaffolds for Orthopedic Applications.

The field of bone tissue engineering is steadily being improved by novel experimental approaches. Nevertheless, microbial adhesion after scaffold implantation remains a limitation that could lead to the impairment of the regeneration process, or scaffold rejection. The present study introduces a methodology that employs laser-based strategies for the development of antimicrobial interfaces on tricalcium phosphate-hydroxyapatite (TCP-HA) scaffolds. The outer surfaces of the ceramic scaffolds with inner porosity were structured using a femtosecond laser (λ = 800 nm; τ = 70 fs) for developing micropatterns and altering local surface roughness. The pulsed laser deposition of ZnO was used for the subsequent functionalization of both laser-structured and unmodified surfaces. The impact of the fs irradiation was investigated by Raman spectroscopy and X-ray diffraction. The effects of the ZnO-layered ceramic surfaces on initial bacterial adherence were assessed by culturing Staphylococcus aureus on both functionalized and non-functionalized scaffolds. Bacterial metabolic activity and morphology were monitored via the Resazurin assay and microscopic approaches. The presence of ZnO evidently decreased the metabolic activity of bacteria and led to impaired cell morphology. The results from this study have led to the conclusion that the combination of fs laser-structured surface topography and ZnO could yield a potential antimicrobial interface for implants in bone tissue engineering.

Corrosion-Resistive ZrO2 Barrier Films on Selected Zn-Based Alloys.

This work presents the enhanced corrosion resistance of newly developed two-layer composite coatings deposited on low-carbon steel: electrodeposited zinc alloy coatings (Zn-Ni with 10 wt.% Ni (ZN) or Zn-Co with 3 wt.% Co (ZC), respectively) and a top ZrO2 sol-gel layer. Surface morphology peculiarities and anti-corrosion characteristics were examined using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDX), atomic force microscopy (AFM), water contact angle (WCA) measurements, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) analyses, potentiodynamic polarization (PDP) curves, corrosion potential (Ecorr), polarization resistance (Rp) measurements (for a prolonged period of 25 days) and open-circuit potential (OCP). The results were compared with the corrosion peculiarities of usual zinc coating. The zirconia top coatings in both systems were amorphous and dense, possessing hydrophobic nature. The experimental data revealed an increased corrosion resistance and protective ability of the ZC system in comparison to that of ZN due to its smooth, homogeneous surface and the presence of poorly crystallized oxides (ZnO and Co3O4), both later playing the role of a barrier for corrosive agents.

Synthesis and Luminescent Properties of Barium Molybdate Nanoparticles.

BaMoO4 was obtained via facile mechanochemical synthesis at room temperature and a solid-state reaction. An evaluation of the phase composition and structural and optical properties of BaMoO4 was conducted. The influence of different milling speeds on the preparation of BaMoO4 was explored. A shorter reaction time for the phase formation of BaMoO4 was achieved using a milling speed of 850 rpm. A milling speed of 500 rpm led to partial amorphization of the initial reagents and to prolongation of the synthesis time of up to 3 h of milling time. Solid-state synthesis was performed via heat treatment at 900 °C for 15 h. X-ray diffraction analysis (XRD), infrared (IR) and UV diffuse reflectance (UV-Vis) and photoluminescence (PL) spectroscopy were carried out to characterize the samples. Independently of the method of preparation, the obtained samples had tetragonal symmetry. The average crystallite sizes of all samples, calculated using Scherrer's formula, were in the range of 240 to 1540 Å. IR spectroscopy showed that more distorted structural MoO4 units were formed when the compound was synthesized via a solid-state reaction. The optical band gap energy of the obtained materials was found to decrease from 4.50 to 4.30 eV with increasing crystallite sizes. Green- and blue-light emissions were observed for BaMoO4 phases under excitation wavelengths of 330 and 488 nm. It was established that the intensity of the PL peaks depends on two factors: the symmetry of MoO4 units and the crystallite sizes.

Study of the Chemical Vapor Deposition of Nano-Sized Carbon Phases on {001} Silicon.

Different nano-sized phases were synthesized using chemical vapor deposition (CVD) processes. The deposition took place on {001} Si substrates at about 1150-1160 °C. The carbon source was thermally decomposed acetone (CH3)2CO in a main gas flow of argon. We performed experiments at two ((CH3)2CO + Ar)/Ar) ratios and observed that two visually distinct types of layers were deposited after a one-hour deposition process. The first layer type, which appears more inhomogeneous, has areas of SiO2 (about 5% of the surface area substrates) beside shiny bright and rough paths, and its Raman spectrum corresponds to diamond-like carbon, was deposited at a (CH3)2CO+Ar)/Ar = 1/5 ratio. The second layer type, deposited at (CH3)2CO + Ar)/Ar = a 1/0 ratio, appears homogeneous and is very dark brown or black in color and its Raman spectrum pointed to defect-rich multilayered graphene. The performed structural studies reveal the presence of diamond and diamond polytypes and seldom SiC nanocrystals, as well as some non-continuously mixed SiC and graphene-like films. The performed molecular dynamics simulations show that there is no possibility of deposition of sp3-hybridized on sp2-hybridized carbon, but there are completely realistic possibilities of deposition of sp2- on sp2- and sp3- on sp3-hybridized carbon under different scenarios.

Picosecond Pulsed Laser Deposition of Metals and Metal Oxides.

In this work, we present the fabrication of thin films/nanostructures of metals and metal oxides using picosecond laser ablation. Two sets of experiments were performed: the depositions were carried out in vacuum and in air at atmospheric pressure. The subjects of investigation were the noble metals Au and Pt and the metal oxides ZnO and TiO2. We studied and compared the phase composition, microstructure, morphology, and physicochemical state of the as-deposited samples' surfaces in vacuum and in air. It was found that picosecond laser ablation performed in vacuum led to the fabrication of thin films with embedded and differently sized nanoparticles. The implementation of the same process in air at atmospheric pressure resulted in the fabrication of porous nanostructures composed of nanoparticles. The ablation of pure Pt metal in air led to the production of nanoparticles with an oxide shell. In addition, more defects were formed on the metal oxide surface when the samples were deposited in vacuum. Furthermore, the laser ablation process of pure Au metal in a picosecond regime in vacuum and in air was theoretically investigated using molecular dynamics simulation.

Formation of Oriented Nanowires from Mixed Metal Oxides.

In this study, we present a physical method for the fabrication of oriented nanowires composed of mixed metal oxides. Pulsed laser deposition carried out in the air under atmospheric pressure was used for the production of samples. Two sets of experiments were performed by applying nanosecond and picosecond laser ablation, respectively. The depositions were performed using the laser ablation of mixed targets from iron oxide and zinc oxide as the initial materials in different ratios. The experiments were carried out in a magnetic field, which allowed us to control the morphology of nanostructures. The structure, microstructure, morphology, and composition of the structures obtained were studied in relation to the sample composition and laser ablation regime applied. The morphological analysis revealed that the structure of the samples consisted mainly of nanowire-like features reaching tens of micrometers in length. These nanowires were composed of nanoparticles and oriented predominantly in parallel to magnetic field lines. Nanoparticles produced using ps ablation were, on average, smaller than those obtained by ns ablation of the same target. Using ablation with ps laser pulses, we were able to produce new composite materials or materials containing unstable phases.

Modification of micro-crystalline graphite and carbon black by acetone, toluene, and phenol.

The chemical interactions of two types of graphite and two types of carbon black (CB) with acetone, toluene, and phenol were studied in order to evaluate the influence of chemical treatment on the structure and morphology of the carbon phases. The experimental treatment of carbon phases was carried out at room temperature for 1 hour. The chemical and phase composition were studied by x-ray photoelectron (XP) and Raman spectroscopies, while the morphology and structure were determined by powder x-ray diffraction, as well as transmission electron microscopy techniques. To shed light on the most probable explanation of the observed results, we performed simulations and calculations of the binding energies of acetone, toluene, and phenol with model carbon phases: a perfect graphene sheet and a defective graphene sheet containing various structural defects (vacancies as well as zigzag and armchair edges). Simulations show that all non-covalent and most covalent coupling reactions are exothermic, with acetone coupling having the higher calorimetric effect. Based on the results of the simulations and the XP spectroscopy measurements, the probable reactions taking place during the respective treatments are outlined. The conducted studies (both theoretical and experimental) show that the treatment of graphite powders and CB with acetone, toluene, or phenol can be used as a preliminary stage of their modification and/or functionalization, including their conversion into graphene-like (defective graphene, reduced graphene oxide, and/or graphene oxide) phases. For example, the treatment of SPHERON 5000 with acetone significantly facilitates their subsequent modification with laser radiation to graphene-like phases.

Novel Approach for Synthesis of Graphene-like Phases by Pulsed Laser Ablation in a Flow-Mode Suspension.

The present study investigates the possibility of obtaining graphene-like phases (defected graphene, graphene oxide, and reduced graphene oxide) as fine suspensions by applying a novel pulsed laser ablation (PLA) approach in flow mode. Two types of suspensions of microcrystalline graphite in aqueous suspensions and two types of microcrystalline graphite in suspensions of 6% hydrogen peroxide solution were irradiated in a quartz tube through which they flow. The third (λ = 355 nm) and fourth harmonics (λ = 266 nm) of an Nd:YAG laser system (15 ns pulse duration and 10 Hz pulse repetition rate) were used. The morphology of the obtained particles was studied by transmission electron microscopy (TEM). Their phase composition and structure were explored by X-ray photoelectron spectroscopy, X-ray diffractometry, and Raman spectroscopy.

Optimizing the Surface Structural and Morphological Properties of Silk Thin Films via Ultra-Short Laser Texturing for Creation of Muscle Cell Matrix Model.

Temporary scaffolds that mimic the extracellular matrix's structure and provide a stable substratum for the natural growth of cells are an innovative trend in the field of tissue engineering. The aim of this study is to obtain and design porous 2D fibroin-based cell matrices by femtosecond laser-induced microstructuring for future applications in muscle tissue engineering. Ultra-fast laser treatment is a non-contact method, which generates controlled porosity-the creation of micro/nanostructures on the surface of the biopolymer that can strongly affect cell behavior, while the control over its surface characteristics has the potential of directing the growth of future muscle tissue in the desired direction. The laser structured 2D thin film matrices from silk were characterized by means of SEM, EDX, AFM, FTIR, Micro-Raman, XRD, and 3D-roughness analyses. A WCA evaluation and initial experiments with murine C2C12 myoblasts cells were also performed. The results show that by varying the laser parameters, a different structuring degree can be achieved through the initial lifting and ejection of the material around the area of laser interaction to generate porous channels with varying widths and depths. The proper optimization of the applied laser parameters can significantly improve the bioactive properties of the investigated 2D model of a muscle cell matrix.

Synthesis and Characterization of Nanocrystalline Boron-Nitride Thin Films by Ion Milling and Thermal Treatment for Tribological Coatings: An Approach to Quantifying the Growth Dynamic Process.

Hexagonal boron-nitride nanoparticle coating was deposited on AISI 1045 steel surface. The deposition process included a transformation of B-containing thin organic film into nanocrystalline BN using two methods: thermal annealing at 450-850 °C and reactive ion etching in Ar/N2 plasma. The film structure, phases, and film morphology of deposited nanoparticles of boron nitride on AISI 1045 steel were characterized by XPS, XRD, and EDS. Post-annealing at 450 °C does not lead to the formation of a BN phase in the layer. A non-stoichiometric BN phase with nitrogen deficiency appears at 650 °C. At 850 °C annealing, the formed BN phase is completely stoichiometric. The effects of deposited and incorporated BN on the friction and hardness properties of AISI 1045 steel were also studied. The post-annealing process improved the hardness from 5.35 to 11.4 GPa, showing a pronounced linear temperature dependence. An original approach was adopted to quantify the energy-dependent growth constants based on the indentation load-discharge curves measured on samples treated under different conditions. Those constants describe the rate of the reactions and the type of interdiffusion process characteristic for each material used. This approach can partially fulfill the role of the Rutherford backscattering spectrometry profile, which is an expensive and time-consuming process, mainly when light elements such as boron and nitrogen are used.

Ultra-Short Laser Surface Properties Optimization of Biocompatibility Characteristics of 3D Poly-ε-Caprolactone and Hydroxyapatite Composite Scaffolds.

The use of laser processing for the creation of diverse morphological patterns onto the surface of polymer scaffolds represents a method for overcoming bacterial biofilm formation and inducing enhanced cellular dynamics. We have investigated the influence of ultra-short laser parameters on 3D-printed poly-ε-caprolactone (PCL) and poly-ε-caprolactone/hydroxyapatite (PCL/HA) scaffolds with the aim of creating submicron geometrical features to improve the matrix biocompatibility properties. Specifically, the present research was focused on monitoring the effect of the laser fluence (F) and the number of applied pulses (N) on the morphological, chemical and mechanical properties of the scaffolds. SEM analysis revealed that the femtosecond laser treatment of the scaffolds led to the formation of two distinct surface geometrical patterns, microchannels and single microprotrusions, without triggering collateral damage to the surrounding zones. We found that the microchannel structures favor the hydrophilicity properties. As demonstrated by the computer tomography results, surface roughness of the modified zones increases compared to the non-modified surface, without influencing the mechanical stability of the 3D matrices. The X-ray diffraction analysis confirmed that the laser structuring of the matrices did not lead to a change in the semi-crystalline phase of the PCL. The combinations of two types of geometrical designs-wood pile and snowflake-with laser-induced morphologies in the form of channels and columns are considered for optimizing the conditions for establishing an ideal scaffold, namely, precise dimensional form, mechanical stability, improved cytocompatibility and antibacterial behavior.

Au nanostructure fabrication by pulsed laser deposition in open air: Influence of the deposition geometry.

We present a fast and flexible method for the fabrication of Au nanocolumns. Au nanostructures were produced by pulsed laser deposition in air at atmospheric pressure. No impurities or Au compounds were detected in the resulting samples. The nanoparticles and nanoaggregates produced in the ablated plasma at atmospheric pressure led to the formation of chain-like nanostructures on the substrate. The dependence of the surface morphology of the samples on the deposition geometry used in the experimental set up was studied. Nanocolumns of different size and density were produced by varying the angle between the plasma plume and the substrate. The electrical, optical, and hydrophobic properties of the samples were studied and discussed in relation to their morphology. All of the nanostructures were conductive, with conductivity increasing with the accumulation of ablated material on the substrate. The modification of the electrical properties of the nanostructures was demonstrated by irradiation by infrared light. The Au nanostructures fabricated by the proposed technology are difficult to prepare by other methods, which makes the simple implementation and realization in ambient conditions presented in this work more ideal for industrial applications.