Visible light- and dark-driven degradation of palm oil mill effluent (POME) over g-C3N4 and photo-rechargeable WO3.

The investigations of real industrial wastewater, such as palm oil mill effluent (POME), as a recalcitrant pollutant remain a subject of global water pollution concern. Thus, this work introduced the preparation and modification of g-C3N4 and WO3 at optimum calcination temperature, where they were used as potent visible light-driven photocatalysts in the degradation of POME under visible light irradiation. Herein, g-C3N4-derived melamine and WO3 photocatalyst were obtained at different calcination temperatures in order to tune their light absorption ability and optoelectronics properties. Both photocatalysts were proven to have their distinct phases, crystallinity levels, and elements with increasing temperature, as demonstrated by the ultraviolet-visible spectroscopy (UV-Vis), X-ray diffraction analysis (XRD), thermogravimetric analysis (TGA), Fourier-transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller (BET), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) results. Significantly, g-C3N4 (580 °C) and WO3 (450 °C) unitary photocatalysts exhibited the highest removal efficiency of POME without dilution due to good crystallinity, extended light absorption, high separation, and less recombination efficiency of electron-hole pairs. Furthermore, surprisingly, the superior energy storage photocatalytic performance with outstanding stability by WO3 achieved an approximately 10% increment during darkness, compared with g-C3N4 under visible light irradiation. Moreover, it has been proven that the WO3 and g-C3N4 photocatalysts are desirable photocatalysts for various pollutant degradations, with excellent visible-light utilization and favorable energy storage application.

A comparative study of the knowledge and practices related to menstrual hygiene among adolescent girls in urban and rural areas of Sindh, Pakistan: A cross-sectional study.

BACKGROUND: Menstrual hygiene management plays a significant role in the achievement of sustainable development goals, including good health and well-being, quality education, gender equality, women's empowerment, and sanitation. Even though the United Nations emphasizes menstrual hygiene management as a global public health and human rights issue, studies from different parts of the world have shown there is a lack of policies in this area that affects adolescent girls. OBJECTIVE: The study aimed to assess the menstrual-related knowledge and practices of adolescent girls (10-18 years) attending urban and rural public schools of district Khairpur of province Sindh of Pakistan. DESIGN: This research is an analytical cross-sectional study design. METHODS: Adolescent girls (n = 310), 159 girls from urban and 159 girls from rural schools, were enrolled. Data were collected through self-administered questionnaires. Knowledge was considered satisfactory if the participant scored ⩾12/20, and <12/20 was considered unsatisfactory knowledge. Practice scores were considered good for >10 and poor for <10. Statistical Package for the Social Science (SPSS) version 20.0 was used for data analysis. Descriptive statistics such as mean and standard deviation were calculated. The chi-square test was used to assess and compare the differences between practices and knowledge of menstrual hygiene management between urban and rural adolescent school girls. RESULTS: We found significant differences in menstrual hygiene management among adolescent girls between urban and rural areas. Approximately two-thirds of the total school girls thought that school management had inadequate resources and toilet facilities (rural: 76% versus urban: 62%). The major source of knowledge in adolescent rural and urban girls for menstrual-related matters was mothers. More girls from the urban school (81%) were aware of using sanitary pads during menstruation. The majority of the girls from urban areas showed satisfactory knowledge whereas only 38% of rural girls were shown to have satisfactory results. Nearly 71% of urban girls were found to have good practices when compared with rural girls (12%). CONCLUSION: With further importance by the United Nations on female education in less developed regions, where the health of women is usually given less importance, policies are required on the inclusion of reproductive health of female adolescents in the curriculum.

Harnessing the photocatalytic potential of bismuth ferrite-activated carbon nanocomposite (BFO-AC) for Staphylococcus aureus decontamination under visible light.

In response to the escalating global issue of microbial contamination, this study introduces a breakthrough photocatalyst: bismuth ferrite-activated carbon (BFO-AC) for visible light-driven disinfection, specifically targeting the Gram-positive bacterium Staphylococcus aureus (S. aureus). Employing an ultrasonication method, we synthesized various BFO-AC ratios and subjected them to comprehensive characterization. Remarkably, the bismuth ferrite-activated carbon 1:1.5 ratio (BA 1:1.5) nanocomposite exhibited the narrowest band gap of 1.86 eV. Notably, BA (1:1.5) demonstrated an exceptional BET surface area of 862.99 m2/g, a remarkable improvement compared to pristine BFO with only 27.61 m2/g. Further investigation through FE-SEM unveiled the presence of BFO nanoparticles on the activated carbon surface. Crucially, the photocatalytic efficacy of BA (1:1.5) towards S. aureus reached its zenith, achieving complete inactivation in just 60 min. TEM analysis revealed severe damage and rupture of bacterial cells, affirming the potent disinfection capabilities of BA (1:1.5). This exceptional disinfection efficiency underscores the promising potential of BA (1:1.5) for the treatment of contaminated water sources. Importantly, our results underscore the enhanced photocatalytic performance with an increased content of activated carbon, suggesting a promising avenue for more effective microorganism inactivation.

A review of research trends on the usage of photocatalysis for wastewater treatment: bibliometric analysis.

Photocatalysis is seen as a viable alternative to treating water pollution, due to its flexibility, low cost, and ability to use visible light which is a plentiful and free energy source. Hence, determining the topics of interest and widening collaboration networks will go a long way in improving research in this field. In this study, we aimed to analyze the global research trends on the usage of photocatalysis for wastewater treatment using bibliometric analysis, centered on the outputs of publications, co-authorships, countries of affiliation, and author's keyword co-occurrences. Bibliometric analysis is a review method that is well-known and more conversant to Social Science. Employing it in Physical Science, which is rarely seen, will provide an avenue and yet another method of determining common research topics as well as the potential opportunities and future research in the field. A potential hybrid review paper of great importance to future research in the area will be produced. A total of 1373 articles published within 27 years between 1993 and 2020 were extracted from the Scopus database. In the beginning, less attention was given to the said topic, because after the oldest article was published in 1993, there was no record of other publications until after 5 years (1998). However, from 2002 there was a growing interest in research in that field, with a cumulative increase every year to date, except for a few years with fewer publications. Meanwhile, the number of publications has risen significantly from 2017 to 2020, with an increase of more than 70 publications every year; this is expected to increase rapidly in the coming years. Recently researchers are focusing on developing efficient photocatalysts for contaminants of emerging concern, like pharmaceutical and refinery wastewater, however, the usage of conducting polymers to produce nanocomposite which was found to be very effective is still lagged in wastewater treatment, as such it will be a good area of future research on effective photocatalysts for wastewater treatment. Supplementary Information: The online version contains supplementary material available at 10.1007/s40899-023-00868-5.

Enhancing Physiochemical Substrate Properties of Thin-Film Composite Membranes for Water and Wastewater Treatment via Engineered Osmosis Process.

The commercial thin-film composite (TFC) nanofiltration (NF) membrane is unsuitable for engineered osmosis processes because of its thick non-woven fabric and semi-hydrophilic substrate that could lead to severe internal concentration polarization (ICP). Hence, we fabricated a new type of NF-like TFC membrane using a hydrophilic coated polyacrylonitrile/polyphenylsulfone (PAN/PPSU) substrate in the absence of non-woven fabric, aiming to improve membrane performance for water and wastewater treatment via the engineered osmosis process. Our results showed that the substrate made of a PAN/PPSU weight ratio of 1:5 could produce the TFC membrane with the highest water flux and divalent salt rejection compared to the membranes made of different PAN/PPSU substrates owing to the relatively good compatibility between PAN and PPSU at this ratio. The water flux of the TFC membrane was further improved without compromising salt rejection upon the introduction of a hydrophilic polydopamine (PDA) coating layer containing 0.5 g/L of graphene oxide (PDA/GO0.5) onto the bottom surface of the substrate. When tested using aerobically treated palm oil mill effluent (AT-POME) as a feed solution and 4 M MgCl2 as a draw solution, the best performing TFC membrane with the hydrophilic coating layer achieved a 67% and 41% higher forward osmosis (FO) and pressure retarded osmosis (PRO) water flux, respectively, compared to the TFC membrane without the coating layer. More importantly, the coated TFC membrane attained a very high color rejection (>97%) during AT-POME treatment, while its water flux and reverse solute flux were even better compared to the commercial NF90 and NF270 membranes. The promising outcomes were attributed to the excellent properties of the PAN/PPSU substrate that was coated with a hydrophilic PDA/GO coating and the elimination of the thick non-woven fabric during TFC membrane fabrication.

Synthesis and Optimization of Superhydrophilic-Superoleophobic Chitosan-Silica/HNT Nanocomposite Coating for Oil-Water Separation Using Response Surface Methodology.

In this current study, facile, one-pot synthesis of functionalised nanocomposite coating with simultaneous hydrophilic and oleophobic properties was successfully achieved via the sol-gel technique. The synthesis of this nanocomposite coating aims to develop a highly efficient, simultaneously oleophobic-hydrophilic coating intended for polymer membranes to spontaneously separate oil-in-water emulsions, therefore, mitigating the fouling issue posed by an unmodified polymer membrane. The simultaneous hydrophilicity-oleophobicity of the nanocoating can be applied onto an existing membrane to improve their capability to spontaneously separate oil-in-water substances in the treatment of oily wastewater using little to no energy and being environmentally friendly. The synthesis of hybrid chitosan-silica (CTS-Si)/halloysite nanotube (HNT) nanocomposite coating using the sol-gel method was presented, and the resultant coating was characterised using FTIR, XPS, XRD, NMR, BET, Zeta Potential, and TGA. The wettability of the nanocomposite coating was evaluated in terms of water and oil contact angle, in which it was coated onto a polymer substrate. The coating was optimised in terms of oil and water contact angle using Response Surface Modification (RSM) with Central Composite Design (CCD) theory. The XPS results revealed the successful grafting of organosilanes groups of HNT onto the CTS-Si denoted by a wide band between 102.6-103.7 eV at Si2p. FTIR spectrum presented significant peaks at 3621 cm-1; 1013 cm-1 was attributed to chitosan, and 787 cm-1 signified the stretching of Si-O-Si on HNT. 29Si, 27Al, and 13H NMR spectroscopy confirmed the extensive modification of the particle's shells with chitosan-silica hybrid covalently linked to the halloysite nanotube domains. The morphological analysis via FESEM resulted in the surface morphology that indicates improved wettability of the nanocomposite. The resultant colloids have a high colloid stability of 19.3 mV and electrophoretic mobility of 0.1904 µmcm/Vs. The coating recorded high hydrophilicity with amplified oleophobic properties depicted by a low water contact angle (WCA) of 11° and high oil contact angle (OCA) of 171.3°. The optimisation results via RSM suggested that the optimised sol pH and nanoparticle loadings were pH 7.0 and 1.05 wt%, respectively, yielding 95% desirability for high oil contact angle and low water contact angle.

Development of Free-Standing Titanium Dioxide Hollow Nanofibers Photocatalyst with Enhanced Recyclability.

Titanium dioxide hollow nanofibers (THN) are excellent photocatalysts for the photodegradation of Bisphenol A (BPA) due to their extensive surface area and good optical properties. A template synthesis technique is typically employed to produce titanium dioxide hollow nanofibers. This process, however, involves a calcination procedure at high temperatures that yields powder-form photocatalysts that require post-recovery treatment before recycling. Meanwhile, the immobilization of photocatalysts on/into a membrane has been reported to reduce the active surface area. Novel free-standing TiO2 hollow nanofibers were developed to overcome those shortcomings. The free-standing photocatalyst containing 0.75 g of THN (FS-THN-75) exhibited good adherence and connectivity between the nanofibers. The recyclability of FS-THN-75 outperformed the THN calcined at 600 °C (THN-600), which retained 80% of its original weight while maintaining excellent degradation performance. This study recommends the potential application of free-standing TiO2 hollow nanofibers as high potential novel photocatalysts for the treatment of BPA in wastewater.

A review of the potential of conventional and advanced membrane technology in the removal of pathogens from wastewater.

Consumption of pathogenic contaminated water has claimed the lives of many people. Hence, this scenario has emphasized the urgent need for research methods to avoid, treat and eliminate harmful pathogens in wastewater. Therefore, effective water treatment has become a matter of utmost importance. Membrane technology offers purer, cleaner, and pathogen-free water through the water separation method via a permeable membrane. Advanced membrane technology such as nanocomposite membrane, membrane distillation, membrane bioreactor, and photocatalytic membrane reactor can offer synergistic effects in removing pathogen through the integration of additional functionality and filtration in a single chamber. This paper also comprehensively discussed the application, challenges, and future perspective of the advanced membrane technology as a promising alternative in battling pathogenic microbial contaminants, which will also be beneficial and valuable in managing pandemics in the future as well as protecting human health and the environment. In addition, the potential of membrane technology in battling the ongoing global pandemic of coronavirus disease 2019 (COVID-19) was also discussed briefly.

Synthesis and Characterization of Titanium Dioxide Hollow Nanofiber for Photocatalytic Degradation of Methylene Blue Dye.

Environmental crisis and water contamination have led to worldwide exploration for advanced technologies for wastewater treatment, and one of them is photocatalytic degradation. A one-dimensional hollow nanofiber with enhanced photocatalytic properties is considered a promising material to be applied in the field. Therefore, we synthesized titanium dioxide hollow nanofibers (THNF) with extended surface area, light-harvesting properties and an anatase-rutile heterojunction via a template synthesis method and followed by a calcination process. The effect of calcination temperature on the formation and properties of THNF were determined and the possible mechanism of THNF formation was proposed. THNF nanofibers produced at 600 °C consisted of a mixture of 24.2% anatase and 75.8% rutile, with a specific surface area of 81.2776 m2/g. The hollow nanofibers also outperformed the other catalysts in terms of photocatalytic degradation of MB dye, at 85.5%. The optimum catalyst loading, dye concentration, pH, and H2O2 concentration were determined at 0.75 g/L, 10 ppm, pH 11, and 10 mM, respectively. The highest degradation of methylene blue dye achieved was 95.2% after 4 h of UV irradiation.

Superwetting materials for hydrophilic-oleophobic membrane in oily wastewater treatment.

The vast amount of oily wastewater released to the environment through industrialization has worsened the water quality in recent years, posing adverse impacts on general human health. Oil emulsified in water is one of the most difficult mixtures to be treated, making it imperative for new technology to be explored to address this issue. The use of conventional water treatment such as flotation, coagulation, precipitation, adsorption, and chemical treatment have low separation efficiencies and high energy costs, and are not applicable to the separation of oil/water emulsions. Therefore, there is a demand for more efficient methods and materials for the separations of immiscible oil/water mixtures and emulsions. Superwetting materials that can repel oil, while letting water pass through have been widely explored to fit into this concern. These materials usually make use of simultaneous hydrophilic/oleophobic mechanisms to allow a solid surface to separate oily emulsion with little to no use of energy. Also, by integrating specific wettability concepts with appropriate pore scale, solid surfaces may achieve separation of multifarious oil/water mixtures namely immiscible oil/water blends and consolidated emulsions. In this review, materials used to impart superwetting in solid surfaces by focusing on superhydrophilic/superoleophobic wetting properties of the materials categorized into fluorinated and non-fluorinated surface modification are summarized. In each material, its background, mechanism, fabricating processes, and their effects on solid surface's wetting capability are elaborated in detail. The materials reviewed in this paper are mainly organic and green, suggesting the alternative material to replace the fluorine group that is widely used to achieve oleophobicity in oily wastewater treatment.

Halloysite Nanotube-Ferrihydrite Incorporated Polyethersulfone Mixed Matrix Membrane: Effect of Nanocomposite Loading on the Antifouling Performance.

Membrane filtration is an attractive process in water and wastewater treatment, but largely restricted by membrane fouling. In this study, the membrane fouling issue is addressed by developing polyethersulfone (PES)-based mixed matrix membranes (MMMs) with the incorporation of hydrophilic nanoparticles as an additive. Ultrafiltration MMMs were successfully fabricated by incorporating different loadings of halloysite nanotube-ferrihydrates (HNT-HFO) into a polyethersulfone (PES) matrix and their performance was evaluated for the separation of bovine serum albumin (BSA) solution and oil/water emulsion. The results show that wettability is endowed to the membrane by introducing the additive aided by the presence of abundant -OH groups from the HFO. The loading of additive also leads to more heterogeneous surface morphology and higher pure water fluxes (516.33-640.82 L/m2h) more than twice that of the pristine membrane as reference (34.69 L/m2h) without affecting the rejection. The MMMs also provide much enhanced antifouling properties. The filtration results indicate that the flux recovery ratio of the modified membrane reached 100% by washing with only distilled water and a total flux recovery ratio of >98% ± 0.0471 for HNT-HFO-loaded membranes in comparison with 59% ± 0.0169 for pristine PES membrane.

Impacts of Secondary Mixed Monomer on Properties of Thin Film Composite (TFC) Nanofiltration and Reverse Osmosis Membranes: A Review.

Polyamide (PA) Thin-Film Composite (TFC) membranes are widely used for large-scale water and wastewater treatment processes worldwide owing to their good balance between water permeability and dissolved solutes separation rate. The physicochemical properties of the cross-linked PA layer are the main criteria determining the filtration performance of the resultant TFC membrane, and this selective layer can be created through Interfacial Polymerization (IP) between two immiscible active monomers, i.e., amine monomer in aqueous solution and acyl chloride monomer in organic solution. This patent review article intends to provide insights to researchers in fabricating improved properties of TFC membranes through the utilization of secondary monomers during IP process. To the best of our knowledge, this is the first review that gives a state-of-the-art account of the subject matter by emphasizing the impacts of secondary monomers (both amine and acyl chloride monomers) on the properties of conventional TFC membranes for nanofiltration and reverse osmosis applications. Our review indicated that the introduction of secondary monomers into either aqueous or organic solution could alter the physical and chemical properties of PA layer, which led to variations in membrane filtration performance. Nevertheless, more research is still required, as most of the secondary monomers reported in the literature did not overcome the membrane trade-off effect between permeability and selectivity. The subject of improved PA layer development is a multi-disciplinary study that requires researchers with different backgrounds (e.g., materials science, chemistry, physics and engineering) to work together.

Novel Activated Carbon Nanofibers Composited with Cost-Effective Graphene-Based Materials for Enhanced Adsorption Performance toward Methane.

Various types of activated carbon nanofibers' (ACNFs) composites have been extensively studied and reported recently due to their extraordinary properties and applications. This study reports the fabrication and assessments of ACNFs incorporated with graphene-based materials, known as gACNFs, via simple electrospinning and subsequent physical activation process. TGA analysis proved graphene-derived rice husk ashes (GRHA)/ACNFs possess twice the carbon yield and thermally stable properties compared to other samples. Raman spectra, XRD, and FTIR analyses explained the chemical structures in all resultant gACNFs samples. The SEM and EDX results revealed the average fiber diameters of the gACNFs, ranging from 250 to 400 nm, and the successful incorporation of both GRHA and reduced graphene oxide (rGO) into the ACNFs' structures. The results revealed that ACNFs incorporated with GRHA possesses the highest specific surface area (SSA), of 384 m2/g, with high micropore volume, of 0.1580 cm3/g, which is up to 88% of the total pore volume. The GRHA/ACNF was found to be a better adsorbent for CH4 compared to pristine ACNFs and reduced graphene oxide (rGO/ACNF) as it showed sorption up to 66.40 mmol/g at 25 °C and 12 bar. The sorption capacity of the GRHA/ACNF was impressively higher than earlier reported studies on ACNFs and ACNF composites. Interestingly, the CH4 adsorption of all ACNF samples obeyed the pseudo-second-order kinetic model at low pressure (4 bar), indicating the chemisorption behaviors. However, it obeyed the pseudo-first order at higher pressures (8 and 12 bar), indicating the physisorption behaviors. These results correspond to the textural properties that describe that the high adsorption capacity of CH4 at high pressure is mainly dependent upon the specific surface area (SSA), pore size distribution, and the suitable range of pore size.

Performance of Polymer Electrolyte Membrane for Direct Methanol Fuel Cell Application: Perspective on Morphological Structure.

Membrane morphology plays a great role in determining the performance of polymer electrolyte membranes (PEMs), especially for direct methanol fuel cell (DMFC) applications. Membrane morphology can be divided into two types, which are dense and porous structures. Membrane fabrication methods have different configurations, including dense, thin and thick, layered, sandwiched and pore-filling membranes. All these types of membranes possess the same densely packed structural morphology, which limits the transportation of protons, even at a low methanol crossover. This paper summarizes our work on the development of PEMs with various structures and architecture that can affect the membrane's performance, in terms of microstructures and morphologies, for potential applications in DMFCs. An understanding of the transport behavior of protons and methanol within the pores' limits could give some perspective in the delivery of new porous electrolyte membranes for DMFC applications.

Adsorptive removal of heavy metal ions using graphene-based nanomaterials: Toxicity, roles of functional groups and mechanisms.

The endless introduction of toxic heavy metals through industrialization has worsened the heavy metal pollution in the environment. Thus, the need for its effective removal has become more crucial than before. Studies on graphene-based nanomaterials and their use in removing heavy metals are gaining tremendous traction over the past decade. The properties of graphene oxide (GO), such as large surface areas, desired functional groups and excellent mechanical properties are advantageous. Nevertheless, due to its tendency to agglomerate and difficulty in phase separation after treatment, the functionalization of GO using various materials of different surface functional groups is an ongoing study. The surface modification of GO is done by using various materials to introduce heteroatoms, which have high affinity for heavy metals. This review summarizes the utilization of different surface functional groups, such as oxygen-containing, nitrogen-containing, and sulphur-containing functionalized graphene oxide composites in the adsorption of cationic and oxyanionic heavy metals. The toxicity of these heavy metals is also addressed. Furthermore, the interactions between adsorbents and heavy metals which are influenced by pH and surface functional groups, are also discussed in detail. This is followed by the review in adsorption isotherms and kinetics. Future research needs are also offered.

Development of Copper-Aluminum Layered Double Hydroxide in Thin Film Nanocomposite Nanofiltration Membrane for Water Purification Process.

This study aims to fabricate a thin film composite (TFC) membrane, modified with copper-aluminium layered double hydroxide (LDH) nanofillers via interfacial polymerization technique for nanofiltration (NF) processes. It was found that Cu-Al LDH nanofillers possessed layered structured materials with typical hexagonal plate-like shape and positive surface charge. The study revealed that TFN membrane exhibits a relatively smooth surface and a less nodular structure compared to pristine TFC membrane. The contact angle of TFN progressively decreased from 54.1° to 37.25°, indicating enhancement in surface hydrophilicity. Moreover, the incorporation of LDH nanofillers resulted in a less negative membrane as compared to the pristine TFC membrane. The best NF performance was achieved by TFN2 membrane with 0.1° of Cu-Al LDH loading and a water flux of 7.01 Lm-2h-1.bar. The addition of Cu-Al LDH resulted in excellent single salt rejections of Na2SO4 (96.8%), MgCl2 (95.6%), MgSO4 (95.4%), and NaCl (60.8%). The improvement in anti-fouling properties of resultant TFN membranes can be observed from the increments of pure water flux recovery and normalized water flux by 14% and 25% respectively. The findings indicated that Cu-Al LDH is a promising material in tailoring membrane surface properties and fouling resistance. The modification of the LDH-filled TFN membrane shows another alternative to fabricating a high-performance composite membrane, especially for water softening and partial desalination process.

Patient satisfaction on the utilization of traditional and complementary medicine services at public hospitals in Malaysia.

BACKGROUND: Traditional and complementary medicine (T&CM) has been integrated into the Malaysian public healthcare system since the establishment of the first T&CM unit at a public hospital in 2007. Assessing patient satisfaction is a vital component of health service evaluation. The main objective of this study is to determine the level of patient satisfaction with the utilization of T&CM services at public hospitals in Malaysia and assess the sociodemographic influence on the overall reporting of satisfaction. This study also aims to analyze the response of the patients towards expansion of T&CM services in the public sector in Malaysia. MATERIALS AND METHODS: A study was conducted to analyze data on the utilization of T&CM services within public hospitals. Secondary data on 822 patients' satisfaction with services offered at 15 T&CM units was analyzed to examine the overall levels of satisfaction with T&CM services in public hospitals in Malaysia. RESULTS: Overall, 99.4% of patients were satisfied with T&CM services and most patients (91.8%) felt that T&CM treatment positively impacted their health. Overall satisfaction was not affected by lower levels of satisfaction with subcategories of service, such as the number of treatment sessions received (90.7% satisfied), date to the next appointment (90.7% satisfied), and the absence of adverse effects of treatment received (87.1% satisfied). There were no significant associations between the socioeconomic status of the respondents and the level of satisfaction reported; however, respondents with a monthly salary of Ringgit Malaysia (RM) 1000 to RM 3000 were more than twice as likely to be strongly satisfied with services received (adjusted odds ratios [AOR]: 2.12, 95% CI: 1.19-3.78). CONCLUSION: This study revealed a high level of satisfaction among patients who had received T&CM treatment at public hospitals in Malaysia. High satisfaction with T&CM treatment validates the integrative management approach adopted in patient care within the public hospitals in Malaysia.

Performance of PES/LSMM-OGCN Photocatalytic Membrane for Phenol Removal: Effect of OGCN Loading.

In designing a photocatalytic oxidation system, the immobilized photocatalyst technique becomes highly profitable due to its promising capability in treating organic pollutants such as phenols in wastewater. In this study, hydrophiLic surface modifying macromolecules (LSMM) modified polyethersulfone (PES) hybrid photocatalytic membranes incorporated with oxygenated graphitic carbon nitride (OGCN) was successfully developed using phase inversion technique. The effectiveness of the hybrid photocatalytic membrane was determined under different loading of OGCN photocatalyst (0, 0.5, 1.0, 1.5, 2.0, and 2.5 wt%). The best amount of OGCN in the casting solution was 1.0 wt% as the agglomeration did not occur considering the stability of the membrane performance and morphology. The highest flux of 264 L/m²·h was achieved by PES/LSMM-OGCN1.5wt% membrane. However, the highest flux performance was not an advantage in this situation as the flux reduced the rejection value due to open pores. The membrane with the highest photocatalytic performance was obtained at 1.0 wt% of OGCN loading with 35.78% phenol degradation after 6 h. Regardless of the lower rejection value, the performance shown by the PES/LSMM-OGCN1.0wt% membrane was still competent because of the small difference of less than 1% to that of the PES/LSMM-OGCN0wt% membrane. Based on the findings, it can be concluded that the optimisation of the OGCN loading in the PES hybrid photocatalytic membrane indeed plays an important role towards enhancing the catalyst distribution, phenol degradation, and acceptable rejection above all considerations.

Photocatalytic degradation of oilfield produced water using graphitic carbon nitride embedded in electrospun polyacrylonitrile nanofibers.

Separation and purification of oilfield produced water (OPW) is a major environmental challenge due to the co-production of the OPW during petroleum exploration and production operations. Effective capture of oil contaminant and its in-situ photodegradation is one of the promising methods to purify the OPW. Based on the photocatalytic capability of graphitic carbon nitride (GCN) which was recently rediscovered, photodegradation capability of GCN for OPW was investigated in this study. GCN was synthesized by calcination of urea and further exfoliated into nanosheets. The GCNs were incorporated into polyacrylonitrile nanofibers using electrospinning, which gave a liquid-permeable self-supporting photocatalytic nanofiber mat that can be handled by hand. The photocatalytic nanofiber demonstrated 85.4% degradation of OPW under visible light irradiation, and improved the degradation to 96.6% under UV light. Effective photodegradation of the photocatalytic nanofiber for OPW originates from synergetic effects of oil adsorption by PAN nanofibers and oil photodegradation by GCNs. This study provides an insight for industrial application on purification of OPW through photocatalytic degradation under solar irradiation.