IR Hidden Patterns for Security Labels.

Authentication of a product's originality by anticounterfeiting labels represents a crucial point toward protection against forgery. Fast and scalable fabrication methods of original labels with a high degree of protection are in high demand for the protection of valuable goods. Here, we propose a simple strategy for fabrication of hidden security tags with IR luminescent readout by the direct femtosecond laser patterning of silicon-erbium-silicon sandwiched thin films. The choice of laser processing parameters makes possible the creation of random or quasi-regular self-organized surface nanotextures. The controlled laser-driven oxidation accompanying this process provides simultaneous regulation of the film's optical properties and spontaneous emission yield of the embedded Er atoms. The regimes are detected when optically similar patterned areas demonstrate different Er emission intensities, allowing us to create hidden security tags with facile readout at the C-band telecommunication wavelengths. The obtained results take another step toward the application of IR-luminescent erbium-based anticounterfeiting labels for covert and/or forensic security levels.

Raman Lasing and Transverse Mode Selection in a Multimode Graded-Index Fiber with a Thin-Film Mirror on Its End Face.

Multimode fibers are attractive for high-power lasers if transverse modes are efficiently controlled. Here, a dielectric thin-film mirror (R~20%) is micro-fabricated on the central area of the end face of a 1 km multimode 100/140 µm graded-index fiber and tested as the output mirror of a Raman laser with highly multimode (M2~34) 940 nm diode pumping. In the cavity with highly reflective input FBG, Raman lasing of the Stokes wave at 976 nm starts at the threshold pump power of ~80 W. Mode-selective properties of mirrors with various diameters were tested experimentally and compared with calculations in COMSOL, with the optimum diameter found to be around 12 µm. The measured Raman laser output beam at 976 nm has a quality factor of M2~2 near the threshold, which confirms a rather good selection of the fundamental transverse mode. The power scaling capabilities, together with a more detailed characterization of the output beam's spatial profile, spectrum, and their stability, are performed. An approximately 35 W output power with an approximately 60% slope efficiency and a narrow spectrum has been demonstrated at the expense of a slight worsening of beam quality to M2~3 without any sign of mirror degradation at the achieved intensity of >30 MW/cm2. Further power scaling of such lasers as well as the application of the proposed technique in high-power fiber lasers are discussed.

On the maximization of entropy in the process of thermalization of highly multimode nonlinear beams.

We present a direct experimental confirmation of the maximization of entropy which accompanies the thermalization of a highly multimode light beam, upon its nonlinear propagation in standard graded-index (GRIN) optical fibers.

Cladding-pumped laser and amplifier for E- and S-bands based on multimode bismuth-doped graded-index fibers: toward "watt-level" output power.

In this Letter, we investigated the potential scalability of output power of a cladding-pumped laser and a power amplifier (booster) based on a multimode Bi-doped fiber (BDF) using the mode-selection approach. We fabricated the multimode double-clad graded-index (GRIN) fiber with a confined Bi-doped germanosilicate glass core with a diameter of ≈30 and ≈60 µm. Using femtosecond (fs) inscription technology with high spatial resolution, Bragg gratings of a special transverse structure allowing the selection of low-order modes were written into the core of BDFs. The operation features of the cladding-pumped multimode bismuth-doped GRIN fiber lasers with the inscribed Bragg gratings with various reflection coefficients were investigated. In addition, the behavior of the output power and the beam quality (M2 parameter) of the optical radiation of the developed devices was studied. The CW laser and booster operating at nearly 1.45 µm with maximum output powers of ≈0.8 and ≈1 W, respectively, based on the 60-µm-core BDF under pumping by multimode laser diodes at 808 nm were developed, which are, to the best of our knowledge, the most powerful cladding-pumped BDF devices to date. Near single-mode lasing (M2 <1.3) is demonstrated for a 30-µm-core fiber. The experimental data open new possibilities to achieve higher powers in cladding-pumped BDF sources, which are more cost-effective compared to core-pumped counterparts.

Raman dissipative soliton source of ultrashort pulses in NIR-III spectral window.

We present a novel fiber source of ultrashort pulses at the wavelength of 1660 nm based on the technique of external cavity Raman dissipative soliton generation. The output energy of the generated 30 ps chirped pulses is in the range of 0.5-3.6 nJ with a slope efficiency of 57%. Numerical simulations are in excellent agreement with the experimental results and the shape of the compressed pulses. The compressed pulses consist of a central part with a duration of 300 fs and a weak pedestal. Our results clearly demonstrate the potential to extend the spectral range of the Raman-assisted technique for generating ultra-short pulses to new frequency regions, including biomedical windows. This paves the way for the development of new dissipative soliton sources in these bands.

Spectrum collapse in a 7-core Yb-doped fiber laser with an array of fs-inscribed fiber Bragg gratings.

Femtosecond inscription of fiber Bragg gratings (FBGs) in each core of a cladding-pumped seven-core Yb-doped fiber enables efficient (≈70%) 1064-nm lasing in a robust all-fiber scheme with ≈33 W power, nearly the same for uncoupled and coupled cores. However, the output spectrum is quite different: without coupling, seven individual lines corresponding to the in-core FBG reflection spectra sum up into a broad (0.22 nm) total spectrum, whereas the multiline spectrum collapses into a single narrow line at strong coupling. The developed model shows that the coupled-core laser generates coherent superposition of supermodes at the wavelength corresponding to the geometric mean of the individual FBG spectra, whereas the generated laser line broadens, with a power (0.04-0.12 nm) like the single-core mode of a seven-times larger effective area.

Mode-resolved analysis of pump and Stokes beams in LD-pumped GRIN fiber Raman lasers.

All-fiber Raman lasers have demonstrated their potential for efficient conversion of highly multimode pump beams into high-quality Stokes beams. However, the modal content of these beams has not yet been investigated. In this work, based on a mode decomposition technique, we are able to reveal the details of intermodal interactions in the different operation regimes of continuous wave multimode graded-index fiber Raman lasers. We observed that, above the laser threshold, the residual pump beam is strongly depleted in its transverse modes with principal quantum number below 10. However, the generated Stokes signal beam mainly consists of the fundamental mode, but higher-order modes are also present, albeit with exponentially decreasing population.

Bending induced output power concentration in a core of a 4-core Yb-doped fiber laser.

An all-fiber 4-core Yb-doped laser with a cavity formed by fiber Bragg gratings directly inscribed in each core with femtosecond laser pulses and 4% Fresnel reflection from the output fiber end face is demonstrated. It has been shown that the diameter of the active fiber winding significantly affects the power distribution between the cores, since it affects both the pump power distribution and the cross-coupling between the cores. In particular, with an active fiber winding diameter of 21 cm, the cores behave independently, and the power is distributed almost evenly over all cores. With a winding diameter of 6.5 cm, the lasing is achieved almost exclusively from one core, and a mechanism of that radiation concentration based on bending induced stress in an active multicore fiber is proposed which explains the experimental data. By analyzing the optical and radio-frequency spectra of the output laser radiation, additional details of the 4-core fiber lasing are revealed. In particular, a narrowband (several longitudinal modes) lasing with periodic linear sweeping of central wavelength in time is observed and characterized in the multicore fiber laser, for the first time to our knowledge. It is shown that crosstalk of longitudinal modes arising from different cores is greatly enhanced in the case of a strongly bent fiber.

Mechanism of brightness enhancement in multimode LD-pumped graded-index fiber Raman lasers: numerical modeling.

We develop a comprehensive theory for describing the experimental beam profiles from multimode fiber Raman lasers. We take into account the presence of random linear mode coupling, Kerr beam self-cleaning and intra-cavity spatial filtering. All of these factors play a decisive role in shaping the Stokes beam, which has a predominant fundamental mode content. Although the highly multimode pump beam is strongly depleted, it remains almost insensitive to the different physical effects. As a result, the intensity of the output Stokes beam is an order of magnitude higher than the pump intensity at its maximum, in quantitative agreement with the experimental results and in contrast with the simplified balance model.

Spatio-spectral beam control in multimode diode-pumped Raman fibre lasers via intracavity filtering and Kerr cleaning.

Multimode fibres provide a promising platform for boosting the capacity of fibre links and the output power of fibre lasers. The complex spatiotemporal dynamics of multimode beams may be controlled in spatial and temporal domains via the interplay of nonlinear, dispersive and dissipative effects. Raman nonlinearity induces beam cleanup in long graded-index fibres within a laser cavity, even for CW Stokes beams pumped by highly-multimode laser diodes (LDs). This leads to a breakthrough approach for wavelength-agile high-power lasers. However, current understanding of Raman beam cleanup is restricted to a small-signal gain regime, being not applicable to describing realistic laser operation. We solved this challenge by experimentally and theoretically studying pump-to-Stokes beam conversion in a graded-index fibre cavity. We show that random mode coupling, intracavity filtering and Kerr self-cleaning all play a decisive role for the spatio-spectral control of CW Stokes beams. Whereas the depleted LD pump radiation remains insensitive to them.

Over 400 W graded-index fiber Raman laser with brightness enhancement.

The power scaling on all-fiberized Raman fiber oscillator with brightness enhancement (BE) based on multimode graded-index (GRIN) fiber is demonstrated. Thanks to beam cleanup of GRIN fiber itself and single-mode selection properties of the fiber Bragg gratings inscribed in the center of GRIN fiber, the efficient BE is realized. For the laser cavity with single OC FBG, continuous-wave power of 334 W with an M2 value of 2.8 and BE value of 5.6 were obtained at a wavelength of 1120 nm with an optical-to-optical efficiency of 49.6%. Furthermore, the cavity reflectivity is increased by employing two OC FBGs to scale the output power up to 443 W, while the corresponding M2 is 3.5 with BE of 4.2. To our best knowledge, it is the highest power in Raman oscillator based on GRIN fiber.

Brightness enhancement in random Raman fiber laser based on a graded-index fiber with high-power multimode pumping.

A brightness-enhanced random Raman fiber laser (RRFL) with maximum power of 306 W at 1120 nm is demonstrated. A half-open cavity is built based on a graded-index (GRIN) passive fiber and single high-reflective fiber Bragg grating written in it directly. Due to the beam cleanup effect in the GRIN fiber enhanced in the half-open RRFL cavity, the output beam quality factor M2 is improved from 9.15 (pump) to 1.76-2.35 (Stokes) depending on power, while the pump-Stokes brightness enhancement (BE) factor increases proportionally to output power reaching 6.1 at maximum. To the best of our knowledge, this is the highest power GRIN RRFL with BE.

An ultrahigh-resolution soft x-ray microscope for quantitative analysis of chemically heterogeneous nanomaterials.

The analysis of chemical states and morphology in nanomaterials is central to many areas of science. We address this need with an ultrahigh-resolution scanning transmission soft x-ray microscope. Our instrument provides multiple analysis tools in a compact assembly and can achieve few-nanometer spatial resolution and high chemical sensitivity via x-ray ptychography and conventional scanning microscopy. A novel scanning mechanism, coupled to advanced x-ray detectors, a high-brightness x-ray source, and high-performance computing for analysis provide a revolutionary step forward in terms of imaging speed and resolution. We present x-ray microscopy with 8-nm full-period spatial resolution and use this capability in conjunction with operando sample environments and cryogenic imaging, which are now routinely available. Our multimodal approach will find wide use across many fields of science and facilitate correlative analysis of materials with other types of probes.

Advanced distributed feedback lasers based on composite fiber heavily doped with erbium ions.

Specially designed composite heavily Er3+-doped fiber in combination with unique point-by-point inscription technology by femtosecond pulses at 1,026 nm enables formation of distributed-feedback (DFB) laser with ultra-short cavity length of 5.3 mm whose parameters are comparable and even better than those for conventional Er3+-doped fiber DFB lasers having much longer cavity. The composite fiber was fabricated by melting rare-earth doped phosphate glass in silica tube. The ultra-short DFB laser generates single-polarization single-frequency radiation at 1,550 nm with narrow linewidth (3.5 kHz) and 0.5 mW output power at 600 mW 980-nm pumping. The same fiber with conventional CW UV (244 nm) inscription technology using phase mask enables fabrication of 40-mm long DFB laser with > 18 mW output power at 3.3% pump conversion, which is a record efficiency for Er3+-doped fiber DFB lasers. The developed technologies form an advanced platform for Er3+-doped fiber DFB lasers operating around 1.55 µm with excellent output characteristics and unique practical features, in particular, the ultra-short DFB lasers are attractive for sensing applications.

Super-resolution surface slope metrology of x-ray mirrors.

We present experimental, analytical, and numerical methods developed for reconstruction (deconvolution) of one-dimensional (1D) surface slope profiles over the spatial frequency range where the raw data are significantly perturbed due to the limited resolution of the measurement instrument. We characterize the spatial resolution properties of a profiler with the instrument's transfer function (ITF). To precisely measure the ITF, we apply a recently developed method utilizing test surfaces with 1D linear chirped height profiles of constant slope amplitude. Based on the results of the ITF calibration, we determine parameters of an analytical model for the ITF that is used in the original reconstruction software. Here, we treat surface slope metrology data obtained with the Optical Surface Measuring System (OSMS), using as a sensor an electronic autocollimator (AC) ELCOMAT-3000. The spatial resolution of the OSMS is limited by the size of the AC light-beam-collimating aperture. For the purposes of this investigation, the OSMS is equipped with a circular aperture with a diameter of 2.5 mm. This is a typical arrangement of most AC-based slope profilers developed for surface slope metrology of state-of-the-art x-ray mirrors. Using the example of surface slope metrology of two state-of-the-art elliptically shaped x-ray focusing mirrors, we demonstrate that the developed data reconstruction procedure allows us to significantly improve the accuracy of surface slope metrology with the OSMS over the spatial wavelength range from ∼1.6 mm to 7 mm. Thus, the amplitude of the quasi-periodic error characteristic of the deterministic polishing process used appears to be higher by a factor of ∼2 than is apparent from the rough metrology data. Underestimation of the surface slope errors in this spatial wavelength range can lead to serious errors in the expected performance of x-ray mirrors in synchrotron beamlines, especially at modern light sources utilizing coherent x rays, where the perturbations can lead to increased speckle-like intensity variation.

Durable shape sensor based on FBG array inscribed in polyimide-coated multicore optical fiber.

The paper presents a novel three-dimensional quasi-continuous shape sensor based on an FBG array inscribed by femtosecond laser pulses into a 7-core optical fiber with a polyimide protective coating. The measured bending sensitivity of individual FBGs ranges from 0.046 nm/m-1 to 0.049 nm/m-1. It is shown that the sensor allows for reconstructing 2- and 3-dimensional shapes with high accuracy. Due to the high value of the core aperture and individual calibration of each FBG we were able to measure the smallest reported bending radii down to 2.6 mm with a record accuracy of ∼1%. Moreover, we investigate the magnitude of the errors of curves reconstruction and errors associated with measurement of curvature radii in the range from 2.6 to 500 mm. The main factors affecting the accuracy of measurements are also discussed. The temperature resistance of both the inscribed FBG structures and of the protective coating, along with the high mechanical strength of the polyimide, makes it possible to use the sensor in harsh environments or in medical and composite material applications.

Arrays of fiber Bragg gratings selectively inscribed in different cores of 7-core spun optical fiber by IR femtosecond laser pulses.

In this paper, we present a new method of point-by-point femtosecond inscription of fiber Bragg gratings (FBG) arrays of different configurations in a 7-core spun optical fiber. The possibility of FBGs inscription with predefined periods in individual fiber cores allowed us to realize: 1) longitudinal FBG arrays with identical or variable resonant wavelengths in all side cores, 2) longitudinal FBG arrays inscribed only in the central or in the selected side core, and 3) an FBG array in a transverse cross section of a fiber consisting of an FBG inscribed in the central and three side cores. Based on the proposed method, by enabling the inscription through the acrylate protective coating of the fiber, a vector bend sensor has been created. Implementation of this sensor has shown that bending radii less than 4 mm can be measured with a high precision using a single-channel interrogation scheme.

2nd-order random lasing in a multimode diode-pumped graded-index fiber.

Raman lasing in a graded-index fiber (GIF) attracts now great deal of attention due to the opportunity to convert high-power multimode laser diode radiation into the Stokes wave with beam quality improvement based on the Raman clean-up effect. Here we report on the cascaded Raman generation of the 2nd Stokes order in the 1.1-km long GIF with 100-µm core directly pumped by 915-nm diodes. In the studied all-fiber scheme, the 1st Stokes order is generated at 950-954 nm in a linear cavity formed at GIF ends by two fiber Bragg gratings (FBGs) securing beam quality improvement from M2 ≈ 30 to M2 ≈ 2.3 due to special transverse structure of FBGs. The 2nd Stokes wave is generated either in linear (two FBGs) or half-open (one FBG) cavity with random distributed feedback via Rayleigh backscattering. Their comparison shows that the random lasing provides better beam quality and higher slope efficiency. Nearly diffraction limited beam (M2 ≈ 1.6) with power up to 27 W at maximum gain (996 nm), and 17 W at the detuned wavelength of 978 nm has been obtained, thus demonstrating that the 2nd-order random lasing in diode-pumped GIF with FBGs provides high-efficiency high-quality beam generation in a broad wavelength range within the Raman gain spectral profile.

Generation of Raman dissipative solitons near 1.3 microns in a phosphosilicate-fiber cavity.

An external-cavity generation of powerful ultrashort pulses in an all-fiber scheme by using a new type of phosphosilicate polarization maintaining fiber is investigated. The phosphorus-related Stokes shifted Raman pulse near 1.3 microns is observed. Optimization of Stokes output spectrum depending on pump pulse duration (chirp), energy and output coupling ratio of the cavity is performed. As result, the output energy of highly-chirped pulses compressible to 570 fs reaches 1.6 nJ.

Highly efficient all-fiber continuous-wave Raman graded-index fiber laser pumped by a fiber laser.

We report for the first time, to the best of our knowledge, an all-fiber Raman graded-index (GRIN) fiber laser pumped by a fiber laser. This configuration points to potential future power and brightness increases. Continuous-wave power of 135 W with an M2 value of 2.5 was obtained at a wavelength of 1081 nm with an optical-to-optical efficiency of 68%. A commercial GRIN core fiber acts as the Raman fiber in a power oscillator configuration that includes fiber Bragg gratings (FBGs) written onto the GRIN fiber. The efficiency and brightness demonstrated here are, to the best of our knowledge, the highest reported in any Raman GRIN fiber laser. A brightness enhancement of the pump beam by a factor of 5.6 is attained due to the transverse profiles of Raman gain and FBG reflection in the GRIN fiber.