New frontiers in atom probe tomography: a review of research enabled by cryo and/or vacuum transfer systems.

There has been a recent surge in the use of cryo and/or vacuum specimen preparation and transfer systems to broaden the scope of research enabled by the microscopy technique of atom probe tomography. This is driven by the fact that, as for many microscopes, the application of atom probes to air- and temperature-sensitive materials or wet biological specimens has previously been limited by transfer through air at room temperature. Here we provide an overview of areas of research that benefit from these new transfer and analysis protocols, as well as a review of current advances in transfer devices, environmental cells, and glove boxes for controlled specimen manipulation. This includes the study of catalysis and corrosion, biological samples, liquid-solid interfaces, natural aging, and the distribution of hydrogen in materials.

An in-situ approach for preparing atom probe tomography specimens by xenon plasma-focussed ion beam.

A method for the rapid preparation of atom probe tomography (APT) needles using a xenon plasma-focussed ion beam (FIB) instrument is presented and demonstrated on a test sample of Ti-6Al-4V alloy. The method requires significantly less operator input than the standard lift-out protocol, is site-specific and produces needles with minimal ion-beam damage; electron microscopy indicated the needle's surface amorphised/oxidised region to be less than 2 nm thick. The resulting needles were routinely analysable by APT, confirming the expected microstructure and showing negligible Xe contamination.

Direct observation of individual hydrogen atoms at trapping sites in a ferritic steel.

The design of atomic-scale microstructural traps to limit the diffusion of hydrogen is one key strategy in the development of hydrogen-embrittlement-resistant materials. In the case of bearing steels, an effective trapping mechanism may be the incorporation of finely dispersed V-Mo-Nb carbides in a ferrite matrix. First, we charged a ferritic steel with deuterium by means of electrolytic loading to achieve a high hydrogen concentration. We then immobilized it in the microstructure with a cryogenic transfer protocol before atom probe tomography (APT) analysis. Using APT, we show trapping of hydrogen within the core of these carbides with quantitative composition profiles. Furthermore, with this method the experiment can be feasibly replicated in any APT-equipped laboratory by using a simple cold chain.

The atomic structure of polar and non-polar InGaN quantum wells and the green gap problem.

We have used high resolution transmission electron microscopy (HRTEM), aberration-corrected quantitative scanning transmission electron microscopy (Q-STEM), atom probe tomography (APT) and X-ray diffraction (XRD) to study the atomic structure of (0001) polar and (11-20) non-polar InGaN quantum wells (QWs). This paper provides an overview of the results. Polar (0001) InGaN in QWs is a random alloy, with In replacing Ga randomly. The InGaN QWs have atomic height interface steps, resulting in QW width fluctuations. The electrons are localised at the top QW interface by the built-in electric field and the well-width fluctuations, with a localisation energy of typically 20meV. The holes are localised near the bottom QW interface, by indium fluctuations in the random alloy, with a localisation energy of typically 60meV. On the other hand, the non-polar (11-20) InGaN QWs contain nanometre-scale indium-rich clusters which we suggest localise the carriers and produce longer wavelength (lower energy) emission than from random alloy non-polar InGaN QWs of the same average composition. The reason for the indium-rich clusters in non-polar (11-20) InGaN QWs is not yet clear, but may be connected to the lower QW growth temperature for the (11-20) InGaN QWs compared to the (0001) polar InGaN QWs.

Atomic-scale Studies of Uranium Oxidation and Corrosion by Water Vapour.

Understanding the corrosion of uranium is important for its safe, long-term storage. Uranium metal corrodes rapidly in air, but the exact mechanism remains subject to debate. Atom Probe Tomography was used to investigate the surface microstructure of metallic depleted uranium specimens following polishing and exposure to moist air. A complex, corrugated metal-oxide interface was observed, with approximately 60 at.% oxygen content within the oxide. Interestingly, a very thin (~5 nm) interfacial layer of uranium hydride was observed at the oxide-metal interface. Exposure to deuterated water vapour produced an equivalent deuteride signal at the metal-oxide interface, confirming the hydride as originating via the water vapour oxidation mechanism. Hydroxide ions were detected uniformly throughout the oxide, yet showed reduced prominence at the metal interface. These results support a proposed mechanism for the oxidation of uranium in water vapour environments where the transport of hydroxyl species and the formation of hydride are key to understanding the observed behaviour.

An integrated high temperature environmental cell for atom probe tomography studies of gas-surface reactions: instrumentation and results.

An integrated environmental cell has been designed and developed for the latest generation of Atom Probe Tomography LEAP™ instruments, allowing controlled exposure of samples to gases at high temperatures. Following treatment, samples can be transferred through the LEAP vacuum system for subsequent APT analysis, which provides detailed information on changes to chemical microstructures following the reactions with near-atomic resolution. A full description of the cell is presented, along with some sample results on the oxidation of aluminum and two platinum-group alloys, demonstrating the capability of combining exposure/characterization functionality in a single instrument.

Atomic engineering of platinum alloy surfaces.

A major practical challenge in heterogeneous catalysis is to minimize the loading of expensive platinum group metals (PGMs) without degrading the overall catalytic efficiency. Gaining a thorough atomic-scale understanding of the chemical/structural changes occurring during catalyst manufacture/operation could potentially enable the design and production of "nano-engineered" catalysts, optimized for cost, stability and performance. In the present study, the oxidation behavior of a Pt-31 at% Pd alloy between 673-1073 K is investigated using atom probe tomography (APT). Over this range of temperatures, three markedly different chemical structures are observed near the surface of the alloy. At 673 K, the surface oxide formed is enriched with Pd, the concentration of which rises further following oxidation at 773 K. During oxidation at 873 K, a thick, stable oxide layer is formed on the surface with a stoichiometry of PdO, beneath which a Pd-depleted (Pt-rich) layer exists. Above 873 K, the surface composition switches to enrichment in Pt, with the Pt content increasing further with increasing oxidation temperature. This treatment suggests a route for tuning the surfaces of Pt-Pd nanoparticles to be either Pd-rich or Pt-rich, simply by adjusting the oxidation temperatures in order to form two different types of core-shell structures. In addition, comparison of the oxidation behavior of Pt-Pd with Pt-Rh and Pd-Rh alloys demonstrates markedly different trends under the same conditions for these three binary alloys.