Influence of time and different tooth widths on masticatory efficiency and muscular activity in bilateral free-end saddles.

PURPOSE: To evaluate the influence of time on masticatory efficiency and muscular activity during mastication of different types of test foods in participants fitted with a lower bilateral free-end saddle removable partial denture (RPD) with wide or narrow teeth. METHODS: Thirty-six participants consented to undergo evaluation of their masticatory efficiency and recording of their muscular activity, while they wore an RPD with a unified bilateral design, during mastication of different types of test foods. The width of the artificial teeth was changed as follows. Initially (A), the length was adjusted so that the distal end of the mandibular second molars occluded with the distal end of the maxillary second molar (buccolingual width of 7-8 mm). Next (B), the width was decreased to half the maxillary second molars (buccolingual width of only 5 mm). A statistical analysis was performed using SAS software. One-way analysis of variance (ANOVA) was performed followed by Duncan's multiple range tests. RESULTS: At the 2-month follow-up visit, wider teeth demonstrated greater masticatory efficiency than narrower teeth. However, after 4 months, no significant differences were observed between the two tooth widths. No significant differences in muscular activity were observed. CONCLUSION: A reduction of the occlusal table width in free-end saddle RPDs resulted in decreased masticatory efficiency 2 months after denture fabrication, but there was no significant difference in muscular activity between narrow and wide teeth. However, after 4 months, the masticatory efficiency of the participants with narrower teeth improved without any changes in muscular activity.

Effect of clasp design on retention at different intervals using different abutment materials and in a simulated oral condition.

PURPOSE: The purpose of this study was to compare the retention of circlet (E) clasps and back-action clasps against three abutment surface materials during long-term simulation of attachment and detachment. MATERIAL AND METHODS: Forty-eight test models were constructed by placing premolars (natural abutments or metal dies) inside metal blocks to test different abutment retention surface materials (sound enamel, composite resin, and glass-ceramic; 16 each). The models were duplicated into investment models for construction of circlet (E) and back-action clasps. Removal and insertion cycling of clasps was carried out for 250, 500, 1000, 2000, 4000, 8000, and 16,000 cycles. The retention of each clasp was measured before cycling and after each interval. Data were analyzed using 1-way-ANOVA, 2-way-ANOVA, and Mann-Whitney U tests. RESULTS: No significant differences in retention of either clasp were found between the three abutment material surfaces; however, there was a significant decrease in retention force of the circlet (E) clasp between 1000 and 2000 cycles but not of the back-action clasp. CONCLUSIONS: (1) The back-action clasp maintains its retention force for a longer period than the circlet (E) clasp. (2) Composite resin contouring of teeth provided retention comparable to enamel and a ceramic material.

Effects of long-term simulated RPD clasp attachment/detachment on retention loss and wear for two clasp types and three abutment material surfaces.

PURPOSE: The purpose of this in vitro study was to measure the loss of retention and wear of two clasp types (E-circlet, back action) against three abutment materials (enamel, composite, CAD/CAM ceramic) after 16,000 simulated cycles of attachment-detachment. MATERIALS AND METHODS: Forty-eight models were constructed by placing either an upper first premolar or a metal die inside a metal rectangular block. Models were divided according to the abutment teeth into three groups. Group E consisted of 16 unrestored human premolars with sound enamel. Group R had 16 premolars recontoured buccally using composite resin. Group C had 16 metal dies (duplicated from a human premolar) covered by CAD/CAM all-ceramic crowns. On the models, E-circlet (E) and back-action (B) clasps were constructed to engage the model's teeth. Withdrawal and insertion cycling of clasps was carried out for 16,000 cycles by using a chewing simulator. The retention force of each clasp was measured after cycling. An acrylic replica was made for each abutment retention surface before and after cycling. Each replica was examined by SEM, and the wear areas were measured. The data were analyzed statistically using one-way ANOVA, two-way ANOVA, and Mann-Whitney tests. RESULTS: There was no significant retention loss after 16,000 cycles (p≥ 0.05) of both clasps (E, B) on the three abutment materials (E, R, C). The mean of wear areas in mm(2) were 1.83 ± 0.36, 0.85 ± 0.66, 2.37 ± 1.88, 1.7 ± 1.11, 0.6 ± 0.2, and 0.06 ± 0 for EE, BE, ER, BR, EC, and BC, respectively. There were significant differences among the wear areas of the abutment surface of the six subgroups (p≤ 0.05). CONCLUSION: The composite resin contoured surfaces showed more wear than the enamel and ceramic surfaces. E-clasps caused more wear on the abutment materials than back-action clasps.