RESUMO
Metal silicide thin films and nanostructures typically employed in electronics have recently gained significant attention in battery technology, where they are used as active or inactive materials. However, unlike thin films, the science behind the evolution of silicide nanostructures, especially 1D nanowires (NWs), is a key missing aspect. CuxSiy nanostructures synthesized by solvent vapor growth technique are studied as a model system to gain insights into metal silicide formation. The temperature-dependent phase evolution of CuxSiy structures proceeds from Cu>Cu0.83Si0.17>Cu5Si>Cu15Si4. The role of Cu diffusion kinetics on the morphological progression of Cu silicides is studied, revealing that the growth of 1D metal silicide NWs proceeds through an in situ formed, Cu seed-mediated, self-catalytic process. The different CuxSiy morphologies synthesized are utilized as structured current collectors for K-ion battery anodes. Sb deposited by thermal evaporation upon Cu15Si4 tripod NWs and cube architectures exhibit reversible alloying capacities of 477.3 and 477.6 mAh g-1 at a C/5 rate. Furthermore, Sb deposited Cu15Si4 tripod NWs anode tested in Li-ion and Na-ion batteries demonstrate reversible capacities of ≈518 and 495 mAh g-1.
RESUMO
Correction for 'High-coercivity hexaferrite ceramics featuring sub-terahertz ferromagnetic resonance' by Evgeny A. Gorbachev et al., Mater. Horiz., 2022, 9, 1264-1272, DOI: https://doi.org/10.1039/D1MH01797G.
RESUMO
Herein, we demonstrate for the first time compact ferrite ceramics with giant coercivity. The materials are manufactured via sintering single-domain Sr0.67Ca0.33Fe8Al4O19 particles synthesized by a citrate-nitrate auto-combustion method. The obtained ceramics show coercivities up to 22.5 kOe and natural ferromagnetic resonance frequencies (NFMR) in a sub-THz range of 160-282 GHz. At a maximum density of 95%, the sample displays coercivity of 18.5 kOe, which is the highest value among dense ferrite materials reported so far. In addition, we report an unusual blueshift of the NFMR frequency from 160 to 200 GHz, which occurs during material sintering.
RESUMO
This study describes the development and cell culture application of nanometer thick photocrosslinkable thermoresponsive polymer films prepared by physical adsorption. Two thermoresponsive polymers, poly(N-isopropylacrylamide (NIPAm)-co-acrylamidebenzophenone (AcBzPh)) and poly(NIPAm-co-AcBzPh-co-N-tertbutylacrylamide) are investigated. Films are prepared both above and below the polymers' lower critical solution temperatures (LCSTs) and cross-linked, to determine the effect, adsorption preparation temperature has on the resultant film. The films prepared at temperatures below the LCST are smoother, thinner, and more hydrophilic than those prepared above. Human pulmonary microvascular endothelial cell (HPMEC) adhesion and proliferation are superior on the films produced below the polymers LCST compared to those produced above. Cells sheets are detached by simply lowering the ambient temperature to below the LCST. Transmission electron, scanning electron, and light microscopies indicate that the detached HPMEC sheets maintain their integrity.
Assuntos
Reagentes de Ligações Cruzadas/farmacologia , Luz , Nanopartículas/química , Tamanho da Partícula , Regeneração/efeitos dos fármacos , Técnicas de Cultura de Tecidos/métodos , Células 3T3 , Acrilamidas/química , Acrilamidas/farmacologia , Adsorção , Animais , Materiais Biocompatíveis/farmacologia , Proliferação de Células/efeitos dos fármacos , Células Endoteliais/citologia , Células Endoteliais/efeitos dos fármacos , Células Endoteliais/ultraestrutura , Humanos , Pulmão/irrigação sanguínea , Teste de Materiais , Camundongos , Microscopia de Força Atômica , Microvasos/citologia , Nanopartículas/ultraestrutura , Água/químicaRESUMO
Formic acid derived from biomass is known to be used for hydrogen production over Pd catalysts. The effects of preparation variables, structure of the carbon support, surface functional composition on the state of Pd, and catalytic properties of the samples in the vapor-phase decomposition of formic acid were studied. In all catalysts derived from Pd acetate, metal particles visible by conventional TEM had similar sizes, but the adsorption capacity towards CO responded strongly to N-doping of the carbon surface. Moreover, a decrease in the CO/Pd values was accompanied by a significant increase in the reaction rate. Taking account of X-ray photoelectron spectroscopy (XPS) and atomic resolution high-angle annular dark-field scanning transmission electron microscopy (HAADF/STEM) data, the trends observed were assigned to a larger fraction of single electron-deficient Pd atoms in the N-doped samples, which do not adsorb CO but interact with formic acid to produce hydrogen. This was confirmed by extended DFT studies. The obtained results are valuable for the development of Pd catalysts on carbon supports for different processes.
Assuntos
Carbono/química , Formiatos/química , Química Verde/métodos , Hidrogênio/química , Paládio/química , Adsorção , Biomassa , Monóxido de Carbono , CatáliseRESUMO
Amorphous, low-porosity carbon spheres on the order of a few micrometers in size were prepared by carbonization of squalane (C30H62) in supercritical CO2 at 823 K. The spheres were characterized and used as catalysts' supports for Pd. Near-edge X-ray absorption fine structure studies of the spheres revealed sp(2) and sp(3) hybridized carbon. To activate carbons for interaction with a metal precursor, often oxidative treatment of a support is needed. We showed that boiling of the obtained spheres in 28 wt % HNO3 did not affect the shape and bulk structure of the spheres, but led to creation of a considerable amount of surface oxygen-containing functional groups and increase of the content of sp(2) hybridized carbon on the surface. This carbon was seen by scanning transmission electron microscopy in the form of waving graphene flakes. The H/C atomic ratio in the spheres was relatively high (0.4) and did not change with the HNO3 treatment. Palladium was deposited by impregnation with Pd acetate followed by reduction in H2. This gave uniform Pd clusters with a size of 2-4 nm. The Pd supported on the original C spheres showed 2-3 times higher catalytic activity in vapor phase formic acid decomposition and higher selectivity for H2 formation (98-99%) than those for the catalyst based on the HNO3 treated spheres. Using of such low-porosity spheres as a catalyst support should prevent mass transfer limitations for fast catalytic reactions.
RESUMO
The rate of hydrogen production from vapour-phase formic acid decomposition can be increased by 1-2 orders of magnitude by doping a Pd/C catalyst with potassium ions. Surface potassium formate and/or bicarbonate species could be involved in the rate-determining step of this reaction.