RESUMO
AIM: The aim of the present study was (i) to evaluate the clinical performance of reduced-diameter implants placed in the molar area and (ii) to test whether monolithic zirconia implant-supported crowns lead to similar clinical outcomes compared to porcelain-fused-to-metal crowns. MATERIALS AND METHODS: A total of 76 patients needing a single implant crown in the posterior region were recruited. All patients received a titanium-zirconium reduced-diameter implant (Straumann Roxolid, Tissue Level, Standard Plus, diameter 3.3 mm, regular neck) randomly allocated to receive either a (1) monolithic zirconia crown (test) or (2) porcelain-fused-to-metal crown (control). Implant survival, prosthetic outcomes, and patient-reported outcomes were assessed at crown delivery and after 3 years of follow-up. Marginal bone levels (MBL) as well as clinical parameters including probing depth (PD), bleeding on probing (BOP), and plaque levels (PCR) were also recorded. RESULTS: A total of 59 patients were available at the 3-year follow-up; 32 patients with a monolithic zirconia crown (TEST) and 27 patients with a porcelain-fused-to-metal crown (CONTROL). 14 implants (11 implant fractures/3 aseptic losses) were lost leading to an estimated implant survival rate of 80% ± 5.1% (95% CI 70.8%-90.8%). Prosthetic complications were limited to the control group and involved minor chippings. CONCLUSIONS: This type of reduced-diameter implant to support single implant molar crowns in the molar area cannot be recommended. Monolithic zirconia crowns appear to be a viable option in the posterior region showing similar prosthetic outcomes to porcelain-fused-to-metal crowns.
Assuntos
Implantes Dentários , Porcelana Dentária , Humanos , Zircônio , Titânio , Coroas , Dente Molar , Prótese Dentária Fixada por Implante , Falha de Restauração DentáriaRESUMO
AIM: To assess in vitro the workflow for alveolar ridge augmentation with customised 3D printed block grafts and simultaneous computer-assisted implant planning and placement. METHODS: Twenty resin mandible models with an edentulous area and horizontal ridge defect in the region 34-36 were scanned with cone beam computed tomography (CBCT). A block graft for horizontal ridge augmentation in the region 34-36 and an implant in the position 35 were digitally planned. Twenty block grafts were 3D printed out of resin and one template for guided implant placement were stereolithographically produced. The resin block grafts were positioned onto the ridge defects and stabilised with two fixation screws each. Subsequently, one implant was inserted in the position 35 through the corresponding template for guided implant placement. Optical scans of the study models together with the fixated block graft were performed prior to and after implant placement. The scans taken after block grafting were superimposed with the virtual block grafting plan through a best-fit algorithm, and the linear deviation between the planned and the achieved block positions was calculated. The precision of the block fixation was obtained by superimposing the 20 scans taken after grafting and calculating the deviation between the corresponding resin blocks. The superimposition between the scans taken after and prior to implant placement was performed to measure a possible displacement in the block position induced by guided implant placement. The (98-2%)/2 percentile value was determined as a parameter for surface deviation. RESULTS: The mean deviation in the position of the block graft compared to the virtual plan amounted to 0.79 ± 0.13 mm. The mean deviation between the positions of the 20 block grafts measured 0.47 ± 0.2 mm, indicating a clinically acceptable precision. Guided implant placement induced a mean shift of 0.16 ± 0.06 mm in the position of the block graft. CONCLUSIONS: Within the limitations of this in vitro study, it can be concluded that customised block grafts fabricated through CBCT, computer-assisted design and 3D printing allow alveolar ridge augmentation with clinically acceptable predictability and reproducibility. Computer-assisted implant planning and placement can be performed simultaneously with computer-assisted block grafting leading to clinically non-relevant dislocation of block grafts.
Assuntos
Aumento do Rebordo Alveolar , Implantes Dentários , Cirurgia Assistida por Computador , Implantação Dentária Endóssea/métodos , Reprodutibilidade dos Testes , Desenho Assistido por Computador , Tomografia Computadorizada de Feixe Cônico , Cirurgia Assistida por Computador/métodos , Computadores , Aumento do Rebordo Alveolar/métodos , Transplante Ósseo/métodosRESUMO
PURPOSE: To test whether internal accuracy affects the load-bearing capacity of 0.5-mm-thick occlusal veneers made out of milled or heat-pressed lithium disilicate (LS2). MATERIALS AND METHODS: Extracted human molars (N = 80) were divided into four groups (n = 20 each) depending on the bonding substrate (enamel [E] or dentin [D]) and the fabrication method (milling [CAD] or heat pressing [PRE]) for the occlusal LS2 veneers: (1) E-CAD, (2) D-CAD, (3) E-PRE, or (4) D-PRE. After restoration fabrication, the abutment teeth and the corresponding restorations were scanned and superimposed in order to measure the marginal and internal accuracy. After adhesive cementation, the specimens were thermomechanically aged and thereafter loaded until fracture. The load-bearing capacities (Fmax) were measured. Fmax and the marginal and internal accuracy between the groups were compared using Kruskal-Wallis test (P < .05) and pairwise group comparisons. In addition, the relationship between Fmax and the internal accuracy was analyzed using Spearman rank correlation. RESULTS: Median Fmax values (and first and third quartiles) per group were as follows: 1,495 N (Q1: 932; Q3: 2'318) for E-CAD; 1,575 N (Q1: 1,314; Q3: 1,668) for E-PRE; 1,856 N (Q1: 1,555; Q3: 2,013) for D-CAD; and 1,877 N (Q1: 1,566; Q3: 2,131) for D-PRE. No statistical difference was found between the groups (P = .0981). Overall, the internal accuracy in the areas of the cusp (P < .0007) and fossa (P < .0001) showed significant differences. While no significant differences were detected in the marginal area (P = .3518), a significant correlation with a negative linear relationship was found between the 3D internal accuracy and the Fmax values (P = .0007). CONCLUSION: An increase in the internal accuracy raised the load-bearing capacity of minimally invasive LS2 occlusal veneers. In general, the restorations bonded to dentin in the occlusal regions showed a better accuracy compared to those bonded to enamel.