Effects of focused electron beam irradiation parameters on direct nanostructure formation on Ag surfaces.

Metallic nanostructures are applied in many fields, including photonics and plasmonics, due to their ability to absorb or emit light at frequencies which depend on their size and shape. It was recently shown that irradiation by a focused electron beam can promote the growth of nanostructures on metal surfaces and the height of these structures depends on the duration of the irradiation and the material of the surface. However, the effects on growth dynamics of numerous irradiation parameters, such as beam current or angle of incidence, have not yet been studied in detail. We explore the effects of focusing, angle of incidence, and current of the electron beam on the size and shape of the resulting structures on an Ag surface. In addition, we investigate how the nitrogen plasma cleaning procedure of a vacuum chamber can affect the growth of these structures. A beam current of around 40 pA resulted in the fastest structure growth rate. By increasing the beam diameter and angle of incidence the growth rate decreased; however, by raising the beam focus up to 5-6 µm above the surface the growth rate increased. Vacuum chamber cleaning reduced structure growth rate for a few hours. These findings can help to better control and optimise the growth of nanostructures on metal surfaces undergoing irradiation by a focused electron beam.

A non-enzymatic electrochemical hydrogen peroxide sensor based on copper oxide nanostructures.

This article describes the synthesis of nanostructured copper oxide on copper wires and its application for the detection of hydrogen peroxide. Copper oxide petal nanostructures were obtained by a one-step hydrothermal oxidation method. The resulting coating is uniform and dense and shows good adhesion to the wire surface. Structure, surface, and composition of the obtained samples were studied using field-emission scanning electron microscopy along with energy-dispersive spectroscopy and X-ray diffractometry. The resulting nanostructured samples were used for electrochemical determination of the H2O2 content in a 0.1 M NaOH buffer solution using cyclic voltammetry, differential pulse voltammetry, and i-t measurements. A good linear relationship between the peak current and the concentration of H2O2 in the range from 10 to 1800 µM was obtained. The sensitivity of the obtained CuO electrode is 439.19 µA·mM-1. The calculated limit of detection is 1.34 µM, assuming a signal-to-noise ratio of 3. The investigation of the system for sensitivity to interference showed that the most common interfering substances, that is, ascorbic acid, uric acid, dopamine, NaCl, glucose, and acetaminophen, do not affect the electrochemical response. The real milk sample test showed a high recovery rate (more than 95%). According to the obtained results, this sensor is suitable for practical use for the qualitative detection of H2O2 in real samples, as well as for the quantitative determination of its concentration.

A Simple and Rapid Staining Technique for Sex Determination of Trichinella Larvae Parasites by Confocal Laser Scanning Microscopy.

The roundworms of Trichinella genus are worldwide distributed and their prevalence in nature is high. Trichinella genus parasites are the causative agents of foodborne zoonosis trichinellosis. The main prevention and control of the infection are meat inspection by the magnetic stirrer method for the detection of Trichinella larvae in muscle samples. The treatment can be effective if the parasite is discovered early in the intestinal phase. Once the Trichinella larva has reached the muscle tissue, the parasite remains therein and there is no treatment for this life cycle stage. The Trichinella species is dioecious with separate male and female individuals. The developed staining technique that uses confocal laser scanning microscopy (CLSM) displays sufficient results for Trichinella larvae examination and this protocol is applicable to study the internal and external structures and for the sex determination of T. britovi and T. spiralis larvae samples. In the present study, a luminescent derivative was synthesized and used for staining of T. spiralis and T. britovi larvae samples for the examination by CLSM. Various fixatives, such as AFA, 70% ethanol, and Bouin's and Carnoy's solutions were tested for sample preparation. The synthesized luminescent compound demonstrates best visualization results for samples fixed in Bouin's fixative.

Novel dye for detection of callus embryo by confocal laser scanning fluorescence microscopy.

In the present study a new luminescent dye 3-N-(2-pyrrolidinylacetamido)benzanthrone (AZR) was synthesized. Spectroscopic measurements of the novel benzanthrone 3-aminoderivative were performed in seven organic solvents showing strong fluorescence. The capability of the prepared dye for visualization has been tested on flax, red clover and alfalfa to determinate the embryo in plant callus tissue cultures. Callus cells were stained with AZR and further analysed utilizing confocal laser scanning fluorescence microscopy. Performed experiments show high visualization effectiveness of newly synthesized fluorescent dye AZR that is efficient in fast and relatively inexpensive diagnostics of callus embryos that are problematic due to in vitro culture specificity.

Novel luminescent dyes for confocal laser scanning microscopy used in Trematoda parasite diagnostics.

Benzanthrone derivates are now widely used in many industrial and scientific applications as dyes for polymers and textiles. In biochemical, biomedical and diagnostics investigations benzanthrone dyes are used as a lipophilic fluorescent probe since many benzanthrone derivates demonstrate bright fluorescence and they have ability to intercalate between membrane lipids. The aim of research presented here was to assess the luminescence ability of benzanthrone derivatives using microscopic visualization of biological objects. Accordingly, specimens of freshwater trematodes: Diplostomum spathaceum, Diplodiscus subclavatus and Prosotocus confusus, were stained by novel benzanthrone dyes using different fixatives. The samples were examined under a confocal laser scanning microscope. All of the dyes tested demonstrated good results for digestive and reproductive system visualization. Based on obtained results we conclude that benzanthrone dyes could be used for internal and external structure confocal laser scanning microscopic imaging of trematode specimens.

Comparison of diffraction patterns exposed by pulsed and CW lasers on positive-tone photoresist.

Two different grating formation geometries for recording onto the positive-tone photoresist with pulsed laser and continuous-wave sources are analyzed and compared. Diffraction efficiency measurements and atomic force microscopy (AFM) examination have been performed in order to investigate the optical and topographical properties of the recorded structures. Gratings patterned by a continuous-wave laser and by a pulsed laser working in the single pulse and multipulse regimes showed different surface roughness and optical properties. The possible reasons for surface roughness and effective exposure differences between gratings created with pulsed and continuous-wave laser radiations are discussed. The processing schemes for diffractive structures patterned by pulsed laser onto positive-tone photoresist for commercial hologram production are analyzed and presented in this work.

Penetration of nanoparticles in flax (Linum usitatissimum L.) calli and regenerants.

We demonstrate a method for direct delivery of metal nanoparticles to flax calli and regenerant cells by vacuum deposition of metal nanolayers on powdered hormone followed by dispersal of the combined hormone-metal in medium. The penetration and location of the gold (AuNPs) and silver (AgNPs) nanoparticles in calli and in plant regenerants were confirmed by optical absorption spectroscopy and scanning electron microscopy. We detected a significant effect of the AuNPs and AgNPs on the regeneration type of flax calli.