RESUMO
Herein, we report for the first time the use of ternary oxide nanoheterostructure photocatalysts derived from (Nb y , Ti1-y )2CT x MXene in the treatment of water. Three different compositions of binary MXenes, viz., (Ti0.75Nb0.25)2CT x , (Ti0.5Nb0.5)2CT x , and (Ti0.25Nb0.75)2CT x (with T x = OH, F, and Cl), were used as single-source precursor to produce TiNbO x -3:1, TiNbO x -1:1, and TiNbO x -1:3 by controlled-atmosphere thermal oxidation. Phase identification and Le Bail refinements confirmed the presence of a mixture of rutile TiO2 and monoclinic Ti2Nb10O29. Morphological investigations through scanning and transmission electron microscopies revealed the retention of layered nanostructures from the MXene precursors and the fusion of TiO2 and Ti2Nb10O29 nanoparticles in forming nanosheets. Among the three oxide nanoheterostructures, TiNbO x -3:1 exhibited the best photocatalytic performance by the removal of 83% of sulfamethoxazole (SMX) after 2 h of reaction. Such a result is explained by a complex influence of structural, morphological, and electronic properties since TiNbO x -3:1 consisted of small-sized crystallites (40-70 nm) and possessed a higher surface area. The suggested electronic band structure is a type-II heterojunction, where the recombination of electrons and holes is minimized during photocatalytic reactions. The photocatalytic degradation of SMX was promoted by the attack of â¢OH, as evidenced by the detection of 2.2 µM â¢OH, using coumarin as a probe. This study highlights the potential application of MXene-derived oxide nanoheterostructures in wastewater treatment.
RESUMO
The manuscript focuses on an original method of preparation of metatitanic acid when only environmentally safe base substances are used in the synthesis process. The synthesis is based on the reaction of solid titanyl sulfate in an aqueous solution of sodium hydroxide. This method allows for (i) a full preservation of the morphology of the starting titanyl sulfate and (ii) a preparation of metatitanic acid substances with specific parameters. This can be achieved via a precise control of the alkali metal/titanyl sulfate ratio resulting in substances with varying contents of alkali metals or even sulfate anions. The prepared metatitanic acid then also contains very small weakly crystalline particles (2-3 nm) and forms pseudomorphic aggregates whose shape and dimensions correspond to those of the starting titanyl sulfate. These aggregates exhibit regular nanoporosity with a high surface area of up to 500 m2·g-1, have no tendency to form colloids, and are mechanically highly resistant even by high-energy ultrasound. The characterization of the resulting products is done via their chemical composition and methods of structural analysis, as well as by electron microscopy and local analysis. The mechanism of product formation is discussed based on the structure of the precursor, including the so far unknown structure of metatitanic acid.
RESUMO
Hard nitride coatings are commonly employed to protect components subjected to friction, whereby such coatings should possess excellent tribomechanical properties in order to endure high stresses and temperatures. In this study, WN/NbN coatings are synthesized by using the cathodic-arc evaporation (CA-PVD) technique at various negative bias voltages in the 50-200 V range. The phase composition, microstructural features, and tribomechanical properties of the multilayers are comprehensively studied. Fabricated coatings have a complex structure of three nanocrystalline phases: ß-W2N, δ-NbN, and ε-NbN. They demonstrate a tendency for (111)-oriented grains to overgrow (200)-oriented grains with increasing coating thickness. All of the data show that a decrease in the fraction of ε-NbN phase and formation of the (111)-textured grains positively impact mechanical properties and wear behavior. Investigation of the room-temperature tribological properties reveals that with an increase in bias voltage from -50 to -200 V, the wear mechanisms change as follows: oxidative â fatigue and oxidative â adhesive and oxidative. Furthermore, WN/NbN coatings demonstrate a high hardness of 33.6-36.6 GPa and a low specific wear rate of (1.9-4.1) × 10-6 mm3/Nm. These results indicate that synthesized multilayers hold promise for tribological applications as wear-resistant coatings.
RESUMO
MXene is an innovative multilayered material that has been prepared by an acid-salt (HCl + NH4F) etching route and tested for the removal of 133Ba and 137Cs in radioactive conditions for the first time. MXene has exhibited high uptake capacity of about 154.9 and 121.5 mg g-1 for 133Ba and 137Cs, respectively, in 0.01 mol L-1 solution and using 5 g L-1 of adsorbent at natural pH.
RESUMO
New conductive materials for tissue engineering are needed for the development of regenerative strategies for nervous, muscular, and heart tissues. Polycaprolactone (PCL) is used to obtain biocompatible and biodegradable nanofiber scaffolds by electrospinning. MXenes, a large class of biocompatible 2D nanomaterials, can make polymer scaffolds conductive and hydrophilic. However, an understanding of how their physical properties affect potential biomedical applications is still lacking. We immobilized Ti3C2Tx MXene in several layers on the electrospun PCL membranes and used positron annihilation analysis combined with other techniques to elucidate the defect structure and porosity of nanofiber scaffolds. The polymer base was characterized by the presence of nanopores. The MXene surface layers had abundant vacancies at temperatures of 305-355 K, and a voltage resonance at 8 × 104 Hz with the relaxation time of 6.5 × 106 s was found in the 20-355 K temperature interval. The appearance of a long-lived component of the positron lifetime was observed, which was dependent on the annealing temperature. The study of conductivity of the composite scaffolds in a wide temperature range, including its inductive and capacity components, showed the possibility of the use of MXene-coated PCL membranes as conductive biomaterials. The electronic structure of MXene and the defects formed in its layers were correlated with the biological properties of the scaffolds in vitro and in bacterial adhesion tests. Double and triple MXene coatings formed an appropriate environment for cell attachment and proliferation with mild antibacterial effects. A combination of structural, chemical, electrical, and biological properties of the PCL-MXene composite demonstrated its advantage over the existing conductive scaffolds for tissue engineering.
RESUMO
Magnetic separation of microalgae using magnetite is a promising harvesting method as it is fast, reliable, low cost, energy-efficient, and environmentally friendly. In the present work, magnetic harvesting of three green algae (Chlorella vulgaris, Chlorella ellipsoidea, and Auxenochlorella protothecoides) and one cyanobacteria (Microcystis aeruginosa) has been studied. The biomass was flushed with clean air using a 0.22 µm filter and fed CO2 for accelerated growth and faster reach of the exponential growth phase. The microalgae were harvested with magnetite nanoparticles. The nanoparticles were prepared by controlled co-precipitation of Fe2+ and Fe3+ cations in ammonia at room temperature. Subsequently, the prepared Fe3O4 nanoparticles were coated with polyethyleneimine (PEI). The prepared materials were characterized by high-resolution transmission electron microscopy, X-ray diffraction, magnetometry, and zeta potential measurements. The prepared nanomaterials were used for magnetic harvesting of microalgae. The highest harvesting efficiencies were found for PEI-coated Fe3O4. The efficiency was pH-dependent. Higher harvesting efficiencies, up to 99%, were obtained in acidic solutions. The results show that magnetic harvesting can be significantly enhanced by PEI coating, as it increases the positive electrical charge of the nanoparticles. Most importantly, the flocculants can be prepared at room temperature, thereby reducing the production costs.
RESUMO
In the present work, nanotwin structured TiO2 nanotube (TNT) layers are prepared by the electrochemical anodization technique to form the anatase phase and by surface modification via spin-coating of Ce and V precursors to form Ce-TNT and V-TNT, respectively. The surface and cross-sectional images by SEM revealed that the nanotubes have an average diameter of â¼130 nm and a length of â¼14 µm. In addition, the TEM images revealed the nanotwin structures of the nanotubes, especially the anatase (001) and (112) twin surfaces, that increase the transport of photogenerated charges. The photoinduced degradation of caffeine (CAF) by TNT, Ce-TNT, and V-TNT led to a degradation extent of 16%, 26% and 33%, respectively, whereas it increased to 26%, 38%, and 46% in the presence of H2O2, owing to the involvement of Fenton-based processes (in addition to photocatalysis). The effect of the Fenton-based processes accounts for about 10% of the total degradation extent of CAF. Finally, the mechanism of the photoinduced degradation of CAF was investigated. The main oxidative species were the hydroxyl radicals, and the better efficiency of V-TNT over Ce-TNT and TNT was ascribed to its negative surface, thus improving the interactions with CAF.
Assuntos
Peróxido de Hidrogênio , Nanotubos , Eletrodos , Nanotubos/química , Titânio/químicaRESUMO
Ag-decorated TiO2 nanostructured materials are promising photocatalysts. We used non-standard cryo-lyophilization and ArF laser ablation methods to produce TiO2 nanosheets and TiO2 nanostructured thin films decorated with Ag nanoparticles. Both methods have a common advantage in that they provide a single multiply twinned Ag(0) characterized by {111} twin boundaries. Advanced microscopy techniques and electron diffraction patterns revealed the formation of multiply twinned Ag(0) structures at elevated temperatures (500 °C and 800 °C). The photocatalytic activity was demonstrated by the efficient degradation of 4-chlorophenol and Total Organic Carbon removal using Ag-TiO2 nanosheets, because the multiply twinned Ag(0) served as an immobilized photocatalytically active center. Ag-TiO2 nanostructured thin films decorated with multiply twinned Ag(0) achieved improved photoelectrochemical water splitting due to the additional induction of a plasmonic effect. The photocatalytic properties of TiO2 nanosheets and TiO2 nanostructured thin films were correlated with the presence of defect-twinned structures formed from Ag(0) nanoparticles with a narrow size distribution, tuned to between 10 and 20 nm. This work opens up new possibilities for understanding the defects generated in Ag-TiO2 nanostructured materials and paves the way for connecting their morphology with their photocatalytic activity.
RESUMO
Due to the increased demands for drilling and cutting tools working at extreme machining conditions, protective coatings are extensively utilized to prolong the tool life and eliminate the need for lubricants. The present work reports on the effect of a second MeN (Me = Zr, Cr, Mo, Nb) layer in WN-based nanocomposite multilayers on microstructure, phase composition, and mechanical and tribological properties. The WN/MoN multilayers have not been studied yet, and cathodic-arc physical vapor deposition (CA-PVD) has been used to fabricate studied coating systems for the first time. Moreover, first-principles calculations were performed to gain more insight into the properties of deposited multilayers. Two types of coating microstructure with different kinds of lattices were observed: (i) face-centered cubic (fcc) on fcc-W2N (WN/CrN and WN/ZrN) and (ii) a combination of hexagonal and fcc on fcc-W2N (WN/MoN and WN/NbN). Among the four studied systems, the WN/NbN had superior properties: the lowest specific wear rate (1.7 × 10-6 mm3/Nm) and high hardness (36 GPa) and plasticity index H/E (0.93). Low surface roughness, high elastic strain to failure, Nb2O5 and WO3 tribofilms forming during sliding, ductile behavior of NbN, and nanocomposite structure contributed to high tribological performance. The results indicated the suitability of WN/NbN as a protective coating operating in challenging conditions.
RESUMO
Sub-zero treatment of Vanadis 6 steel resulted in a considerable reduction of retained austenite amount, refinement of martensite, enhancement of population density of carbides, and modification of precipitation behaviour. Tempering of sub-zero-treated steel led to a decrease in population density of carbides, to a further reduction of retained austenite, and to precipitation of M3C carbides, while M7C3 carbides precipitated only in the case of conventionally quenched steel. Complementary effects of these microstructural variations resulted in more noble behaviour of sub-zero-treated steel compared to the conventionally room-quenched one, and to clear inhibition of the corrosion rate at the same time.
RESUMO
The distribution of alloyed atoms in semiconductors often deviates from a random distribution which can have significant effects on the properties of the materials. In this study, scanning transmission electron microscopy techniques are employed to analyze the distribution of Bi in several distinctly MBE grown GaAs1-xBix alloys. Statistical quantification of atomic-resolution HAADF images, as well as numerical simulations, are employed to interpret the contrast from Bi-containing columns at atomically abrupt (001) GaAs-GaAsBi interface and the onset of CuPt-type ordering. Using monochromated EELS mapping, bulk plasmon energy red-shifts are examined in a sample exhibiting phase-separated domains. This suggests a simple method to investigate local GaAsBi unit-cell volume expansions and to complement standard X-ray-based lattice-strain measurements. Also, a single-variant CuPt-ordered GaAsBi sample grown on an offcut substrate is characterized with atomic scale compositional EDX mappings, and the order parameter is estimated. Finally, a GaAsBi alloy with a vertical Bi composition modulation is synthesized using a low substrate rotation rate. Atomically, resolved EDX and HAADF imaging shows that the usual CuPt-type ordering is further modulated along the [001] growth axis with a period of three lattice constants. These distinct GaAsBi samples exemplify the variety of Bi distributions that can be achieved in this alloy, shedding light on the incorporation mechanisms of Bi atoms and ways to further develop Bi-containing III-V semiconductors.
RESUMO
The dilute bismide alloy GaAs1-xBix has drawn significant attention from researchers interested in its fundamental properties and the potential for infrared optoelectronics applications. To extend the study of bismides, molecular-beam heteroepitaxy of nominally 1.0 eV bandgap bismide on Ge substrates is comprehensively investigated. Analysis of atomic-resolution anti-phase domain (APD) images in the direct-epitaxy revealed a high-density of Ga vacancies and a reduced Bi content at their boundaries. This likely played a key role in the preferential dissolution of Bi atoms from the APD interiors and Bi spiking in Ge during thermal annealing. Introduction of GaAs buffer on offcut Ge largely suppressed the formation of APDs, producing high-quality bismide with single-variant CuPtB-type ordered domains as large as 200 nm. Atomic-resolution X-ray imaging showed that 2-dimensional Bi-rich (111) planes contain up to x = 9% Bi. The anomalously early onset of localization found in the temperature-dependent photoluminescence suggests enhanced interactions among Bi states, as compared to non-ordered samples. Growth of large-domain single-variant ordered GaAs1-xBix films provides new prospects for detailed analysis of the structural modulation effects and may allow to further tailor properties of this alloy for optoelectronic applications.
RESUMO
Nanocrystalline diamond (NCD) films grown on Si substrates by microwave plasma enhanced chemical vapor deposition (MWPECVD) were subjected to Ni-mediated graphitization to cover them with a conductive layer. Results of transmission electron microscopy including electron energy-loss spectroscopy of cross-sectional samples demonstrate that the oxide layer on Si substrates (â¼5 nm native SiO2) has been damaged by microwave plasma during the early stage of NCD growth. During the heat treatment for graphitizing the NCD layer, the permeability or absence of the oxide barrier allow Ni nanoparticles to diffuse into the Si substrate and cause additional solid-state reactions producing pyramidal crystals of NiSi2 and SiC nanocrystals. The latter are found impinged into the NiSi2 pyramids but only when the interfacial oxide layer is absent, replaced by amorphous SiC. The complex phase morphology of the samples is also reflected in the temperature dependence of electrical conductivity, where multiple pathways of the electronic transport dominate in different temperature regions. We present models explaining the observed cascade of solid-state reactions and resulting electronic transport properties of such heterostructures.
RESUMO
Aberration-corrected transmission electron microscopy of the atomic structure of diamond-graphite interface after Ni-induced catalytic transformation reveals graphitic planes bound covalently to the diamond in the upright orientation. The covalent attachment, together with a significant volume expansion of graphite transformed from diamond, gives rise to uniaxial stress that is released through plastic deformation. We propose a comprehensive model explaining the Ni-mediated transformation of diamond to graphite and covalent bonding at the interface as well as the mechanism of relaxation of uniaxial stress. We also explain the mechanism of electrical transport through the graphitized surface of diamond. The result may thus provide a foundation for the catalytically driven formation of graphene-diamond nanodevices.
RESUMO
Few-layer MoS2 films are promising candidates for applications in numerous areas, such as photovoltaics, photocatalysis, nanotribology, lithium batteries, hydro-desulfurization catalysis and dry lubricants, especially due to their distinctive electronic, optical, and catalytic properties. In general, two alignments of MoS2 layers are possible - the horizontal and the vertical one, having different physicochemical properties. Layers of both orientations are conventionally fabricated by a sulfurization of pre-deposited Mo films. So far, the Mo thickness was considered as a critical parameter influencing the final orientation of MoS2 layers with horizontally and vertically aligned MoS2 grown from thin (1 nm) and thick (3 nm) Mo films, respectively. Here, we present a fabrication protocol enabling the growth of horizontally or vertically aligned few-layer MoS2 films utilizing the same Mo thickness of 3 nm. We show that the sulfur vapor is another parameter influencing the growth mechanism, where a sulfurization with higher sulfur vapor pressure leads to vertical MoS2 layers and slow sulfur evaporation results in horizontally aligned layers for a thicker Mo starting layer.
RESUMO
Background and Aims: Deposition of silica in plant cell walls improves their mechanical properties and helps plants to withstand various stress conditions. Its mechanism is still not understood and silica-cell wall interactions are elusive. The objective of this study was to investigate the effect of silica deposition on the development and structure of sorghum root endodermis and to identify the cell wall components involved in silicification. Methods: Sorghum bicolor seedlings were grown hydroponically with (Si+) or without (Si-) silicon supplementation. Primary roots were used to investigate the transcription of silicon transporters by quantitative RT-PCR. Silica aggregation was induced also under in vitro conditions in detached root segments. The development and architecture of endodermal cell walls were analysed by histochemistry, microscopy and Raman spectroscopy. Water retention capability was compared between silicified and non-silicified roots. Raman spectroscopy analyses of isolated silica aggregates were also carried out. Key Results: Active uptake of silicic acid is provided at the root apex, where silicon transporters Lsi1 and Lsi2 are expressed. The locations of silica aggregation are established during the development of tertiary endodermal cell walls, even in the absence of silicon. Silica aggregation takes place in non-lignified spots in the endodermal cell walls, which progressively accumulate silicic acid, and its condensation initiates at arabinoxylan-ferulic acid complexes. Silicification does not support root water retention capability; however, it decreases root growth inhibition imposed by desiccation. Conclusion: A model is proposed in which the formation of silica aggregates in sorghum roots is predetermined by a modified cell wall architecture and takes place as governed by endodermal development. The interaction with silica is provided by arabinoxylan-ferulic acid complexes and interferes with further deposition of lignin. Due to contrasting hydrophobicity, silicification and lignification do not represent functionally equivalent modifications of plant cell walls.
Assuntos
Raízes de Plantas/crescimento & desenvolvimento , Dióxido de Silício/química , Sorghum/crescimento & desenvolvimento , Parede Celular/química , Raízes de Plantas/metabolismo , Sorghum/metabolismoRESUMO
The control and prevention of biofilm-related infections is an important public healthcare issue. Given the increasing antibiotic resistance among bacteria and fungi that cause serious infections in humans, promotion of new strategies combating microorganisms has been essential. One attractive approach to inactivate microorganisms is the use of semiconductor photo-catalysis, which has become the subject of extensive research. In this study, the bactericidal properties of four photo-catalysts, TiO2, TiO2-S, TiO2-Eu and TiO2-Eu-S, were investigated against established 24, 48, 72 and 96 h biofilms of Enterococcus The exposure of biofilms to the catalysts induced the production of superoxide radical anions. The best photo-catalytic inactivation was achieved with the TiO2-Eu-S and TiO2-S nanopowders and 24 h biofilms. Transmission electron microscopy images showed significant changes in the structure of the biofilm cells following photo-inactivation. The results suggest that doping with europium and modifying the surface with sulphate groups enhanced the bactericidal activity of the TiO2 nanoparticles against enterococcal biofilms.
Assuntos
Biofilmes/efeitos dos fármacos , Enterococcus/efeitos dos fármacos , Viabilidade Microbiana , Nanopartículas/química , Fármacos Fotossensibilizantes/farmacologia , Titânio/farmacologia , Antibacterianos/farmacologia , Biofilmes/crescimento & desenvolvimento , Catálise , Enterococcus/ultraestrutura , Európio/química , Európio/farmacologia , Substâncias Luminescentes/química , Substâncias Luminescentes/farmacologia , Microscopia Eletrônica de Transmissão , Nanopartículas/ultraestrutura , Sulfatos/química , Superóxidos/metabolismoRESUMO
CdS/ZnS nanocomposites have been prepared by a two-step solid-state mechanochemical synthesis. CdS has been prepared from cadmium acetate and sodium sulfide precursors in the first step. The obtained cubic CdS (hawleyite, JCPDS 00-010-0454) was then mixed in the second step with the cubic ZnS (sphalerite, JCPDS 00-005-0566) synthesized mechanochemically from the analogous precursors. The crystallite sizes of the new type CdS/ZnS nanocomposite, calculated based on the XRD data, were 3-4 nm for both phases. The synthesized nanoparticles have been further characterized by high-resolution transmission electron microscopy (HRTEM) and micro-photoluminescence (µPL) spectroscopy. The PL emission peaks in the PL spectra are attributed to the recombination of holes/electrons in the nanocomposites occurring in depth associated with Cd, Zn vacancies and S interstitials. Their photocatalytic activity was also measured. In the photocatalytic activity tests to decolorize Methyl Orange dye aqueous solution, the process is faster and its effectivity is higher when using CdS/ZnS nanocomposite, compared to single phase CdS. Very low cytotoxic activity (high viability) of the cancer cell lines (selected as models of living cells) has been evidenced for CdS/ZnS in comparison with CdS alone. This fact is in a close relationship with Cd(II) ions dissolution tested in a physiological solution. The concentration of cadmium dissolved from CdS/ZnS nanocomposites with variable Cd:Zn ratio was 2.5-5.0 µg.mL(-1), whereas the concentration for pure CdS was much higher - 53 µg.ml(-1). The presence of ZnS in the nanocrystalline composite strongly reduced the release of cadmium into the physiological solution, which simulated the environment in the human body. The obtained CdS/ZnS quantum dots can serve as labeling media and co-agents in future anti-cancer drugs, because of their potential in theranostic applications.
Assuntos
Nanocompostos/química , Compostos de Cádmio/química , Linhagem Celular Tumoral , Sobrevivência Celular/efeitos dos fármacos , Humanos , Células MCF-7 , Nanocompostos/toxicidade , Análise Espectral Raman , Sulfetos/química , Propriedades de Superfície , Testes de Toxicidade , Compostos de Zinco/químicaRESUMO
Iron is an essential element for fundamental cell functions and a catalyst for chemical reactions. Three samples extracted from the human spleen were investigated by scanning (SEM) and transmission electron microscopy (TEM), Mössbauer spectrometry (MS), and SQUID magnetometry. The sample with diagnosis of hemosiderosis (H) differs from that referring to hereditary spherocytosis and the reference sample. SEM reveals iron-rich micrometer-sized aggregate of various structures-tiny fibrils in hereditary spherocytosis sample and no fibrils in hemochromatosis. Hematite and magnetite particles from 2 to 6 µm in TEM with diffraction in all samples were shown. The SQUID magnetometry shows different amount of diamagnetic, paramagnetic and ferrimagnetic structures in the tissues. The MS results indicate contribution of ferromagnetically split sextets for all investigated samples. Their occurrence indicates that at least part of the sample is magnetically ordered below the critical temperature. The iron accumulation process is different in hereditary spherocytosis and hemosiderosis. This fact may be the reason of different iron crystallization.
Assuntos
Compostos Férricos/metabolismo , Ferro/química , Baço/química , Autopsia , Cristalização , Compostos Férricos/química , Óxido Ferroso-Férrico/química , Hemossiderose/metabolismo , Hemossiderose/patologia , Humanos , Ferro/metabolismo , Microscopia Eletrônica de Transmissão , Espectroscopia de Mossbauer , Esferocitose Hereditária/metabolismo , Esferocitose Hereditária/patologia , Baço/metabolismo , Baço/patologia , Baço/ultraestruturaRESUMO
BACKGROUND: Lucilia sericata maggots are applied to chronic wounds to aid healing when conventional treatments have failed. After their application into a necrotic wound, they potentially influence wound healing with a combination of specific proteinases that are involved in the remodeling of extracellular matrix. These proteases cause changes in fibroblast adhesion and spread upon extracellular matrix protein surfaces, affecting integrity of the protein surfaces-especially fibronectin-while maintaining cell viability. OBJECTIVE: This study focused on in vitro monitoring of the effect of homogenate substances prepared from maggot salivary gland of L sericata on the ultrastructure of human neonatal fibroblasts. METHODS: Collagen/hyaluronan membrane was used as the synthetic substitute of extracellular matrix. The cultured human neonatal fibroblasts B-HNF-1 were seeded on the surface of the collagen/hyaluronan membrane and cultured with maggot salivary gland extract (SGE) at a concentration of 2.4 glands/1 mL. RESULTS: The authors observed increased cell metabolism and protein production (euchromatic nucleus, voluminous nuclear membrane, large reticular nuclei, distended and filled cisterns of rough endoplasmic reticulum, Golgi apparatus with saccules, and vesicles packed with fine fibrillar material) after incubating the cells in culture medium with SGE. CONCLUSION: The authors believe that increased cell metabolism and protein production corresponded with formation of microfibrillar net used for migration of fibroblasts in culture, but mainly for proper production of extracellular matrix. The authors suggest that their results may help explain the effect of SGE on wound healing and support implementation of maggot therapy into human medicine.