Insight into the Degradation Mechanisms of Atomic Layer Deposited TiO2 as Photoanode Protective Layer.

Around 100 nm thick TiO2 layers deposited by atomic layer deposition (ALD) have been investigated as anticorrosion protective films for silicon-based photoanodes decorated with 5 nm NiFe catalyst in highly alkaline electrolyte. Completely amorphous layers presented high resistivity; meanwhile, the ones synthesized at 300 °C, having a fully anatase crystalline TiO2 structure, introduced insignificant resistance, showing direct correlation between crystallization degree and electrical conductivity. The conductivity through crystalline TiO2 layers has been found not to be homogeneous, presenting preferential conduction paths attributed to grain boundaries and defects within the crystalline structure. A correlation between the conductivity atomic force microscopy measurements and grain interstitials can be seen, supported by high-resolution transmission electron microscopy cross-sectional images presenting defective regions in crystalline TiO2 grains. It was found that the conduction mechanism goes through the injection of electrons coming from water oxidation from the electrocatalyst into the TiO2 conduction band. Then, electrons are transported to the Si/SiOx/TiO2 interface where electrons recombine with holes given by the p+n-Si junction. No evidences of intra-band-gap states in TiO2 responsible of conductivity have been detected. Stability measurements of fully crystalline samples over 480 h in anodic polarization show a continuous current decay. Electrochemical impedance spectroscopy allows to identify that the main cause of deactivation is associated with the loss of TiO2 electrical conductivity, corresponding to a self-passivation mechanism. This is proposed to reflect the effect of OH- ions diffusing in the TiO2 structure in anodic conditions by the electric field. This fact proves that a modification takes place in the defective zone of the layer, blocking the ability to transfer electrical charge through the layer. According to this mechanism, a regeneration of the degradation process is demonstrated possible based on ultraviolet illumination, which contributes to change the occupancy of TiO2 electronic states and to recover the defective zone's conductivity. These findings confirm the connection between the structural properties of the ALD-deposited polycrystalline layer and the degradation mechanisms and thus highlight main concerns toward fabricating long-lasting metal-oxide protective layers for frontal illuminated photoelectrodes.

Tailoring Copper Foam with Silver Dendrite Catalysts for Highly Selective Carbon Dioxide Conversion into Carbon Monoxide.

The present study outlines the important steps to bring electrochemical conversion of carbon dioxide (CO2) closer to commercial viability by using a large-scale metallic foam electrode as a highly conductive catalyst scaffold. Because of its versatility, it was possible to specifically tailor three-dimensional copper foam through coating with silver dendrite catalysts by electrodeposition. The requirements of high-yield CO2 conversion to carbon monoxide (CO) were met by tuning the deposition parameters toward a homogeneous coverage of the copper foam with nanosized dendrites, which additionally featured crystallographic surface orientations favoring CO production. The presented results evidence that Ag dendrites, owing a high density of planes with stepped (220) surface sites, paired with the superior active surface area of the copper foam can significantly foster the CO productivity. In a continuous flow-cell reactor setup, CO Faradaic efficiencies reaching from 85 to 96% for a wide range of low applied cathode potentials (<1.0 VRHE) along with high CO current densities up to 27 mA/cm2 were achieved, far outperforming other tested scaffold materials. Overall, this research provides new strategic guidelines for the fabrication of efficient and versatile cathodes for CO2 conversion compatible with large-scale integrated prototype devices.

Biosafety assessment of conducting nanostructured materials by using co-cultures of neurons and astrocytes.

Neural electrode implants are made mostly of noble materials. We have synthesized a nanostructured material combining the good electrochemical properties of iridium oxide (IrOx) and carbon-nanotubes (CNT) and the properties of poly(3,4-ethylenedioxythiophene) (PEDOT). IrOx-CNT-PEDOT charge storage capacity was lower than that of IrOx and IrOx-CNT, but higher than that of other PEDOT-containing hybrids and Pt. Cyclic voltammetry, SEM, XPS and micro-Raman spectroscopy suggest that PEDOT encapsulates IrOx and CNT. In our search for a cell culture platform that could optimize modelling the in vivo environment, we determined cell viability, neuron and astrocyte functionality and the response of astrocytes to an inflammatory insult by using primary cultures of neurons, of astrocytes and co-cultures of both. The materials tested (based on IrOx, CNT and PEDOT, as well as Pt as a reference) allowed adhesion and proliferation of astrocytes and full compatibility for neurons grown in co-cultures. Functionality assays show that uptake of glutamate in neuron-astrocyte co-culture was significantly higher than the sum of the uptake in astrocytes and neurons. In co-cultures on IrOx, IrOx-CNT and IrOx-CNT-PEDOT, glutamate was released by a depolarizing stimulus and induced a significant increase in intracellular calcium, supporting the expression of functional NMDA/glutamate receptors. LPS-induced inflammatory response in astrocytes showed a decreased response in NOS2 and COX2 mRNA expression for IrOx-CNT-PEDOT. Results indicate that neuron-astrocyte co-cultures are a reliable model for assessing the biocompatibility and safety of nanostructured materials, evidencing also that hybrid IrOx-CNT-PEDOT nanocomposite materials may offer larger resistance to inflammatory insults.

Role of Bismuth in the Electrokinetics of Silicon Photocathodes for Solar Rechargeable Vanadium Redox Flow Batteries.

The ability of crystalline silicon to photoassist the V3+ /V2+ cathodic reaction under simulated solar irradiation, combined with the effect of bismuth have led to important electrochemical improvements. Besides the photovoltage supplied by the photovoltaics, additional decrease in the onset potentials, high reversibility of the V3+ /V2+ redox pair, and improvement in the electrokinetics were attained thanks to the addition of bismuth. In fact, Bi0 deposition has shown to slightly decrease the photocurrent, but the significant enhancement in the charge transfer, reflected in the overall electrochemical performance clearly justifies its use as additive in a photoassisted system for maximizing the efficiency of solar charge to battery.

IrOx-carbon nanotube hybrids: a nanostructured material for electrodes with increased charge capacity in neural systems.

Nanostructured iridium oxide-carbon nanotube hybrids (IrOx-CNT) deposited as thin films by dynamic electrochemical methods are suggested as novel materials for neural electrodes. Single-walled carbon nanotubes (SWCNT) serve as scaffolds for growing the oxide, yielding a tridimensional structure with improved physical, chemical and electrical properties, in addition to high biocompatibility. In biological environments, SWCNT encapsulation by IrOx makes more resistant electrodes and prevents the nanotube release to the media, preventing cellular toxicity. Chemical, electrochemical, structural and surface characterization of the hybrids has been accomplished. The high performance of the material in electrochemical measurements and the significant increase in cathodal charge storage capacity obtained for the hybrid in comparison with bare IrOx represent a significant advance in electric field application in biosystems, while its cyclability is also an order of magnitude greater than pure IrOx. Moreover, experiments using in vitro neuronal cultures suggest high biocompatibility for IrOx-CNT coatings and full functionality of neurons, validating this material for use in neural electrodes.