Laser light passage through restored and carious posterior teeth.

Laser Doppler flowmetry (LDF) has been used to investigate pulpal blood flow as a means of pulp vitality testing. Transmission of laser light from the tooth surface to the pulp space may be influenced by caries and restorations. One hundred and twenty-two first and second molars that had caries into dentine, restorations or significant loss of coronal tissue were sectioned in half axio-bucco-lingually. The two sections were illuminated with a laser from their buccal and lingual aspects 2 mm coronal to the amelocemental junction. Light reaching the pulp space was recorded. Buccal and lingual illumination sites were equally effective for 67 teeth (55%). Buccal sites alone were effective for 35 teeth (29%), despite over one-third of these surfaces being restored or featuring enamel or dentine caries. A lingual position alone was effective for 20 teeth (16%). Caries affected light transmission, but for over half the teeth, the pulp could be illuminated from all four probe positions. No effect was found when the influence of mesial and distal restorations on transmission into the corresponding tooth section was examined. The pulp spaces of most (84%) restored, and carious posterior teeth could be illuminated by laser light from their buccal aspect and these teeth could potentially be vitality tested using LDF.

Factors associated with pain induced by orthodontic separators.

Pain resulting from the application of orthodontic forces varies markedly across individuals. The reasons of this variability are still largely unknown. To investigate factors that may be associated with orthodontic pain following the application of orthodontic separators. One hundred and seven participants were screened for pain response over 48 h following placement of orthodontic elastomeric separators. The highest (n = 10) and lowest (n = 10) pain responders were identified, and data collected on tooth pain sensitivity to electrical stimulation in conjunction with using the Pain Catastrophising Scale (PCS), Dental Anxiety Scale (DAS) and cold pressor test (CPT). There were statistically significant differences between high- and low-pain responders in catastrophising score (P ≤ 0.023). For every PCS magnification score of 1 unit higher, the relative risk of being a high-pain responder was 1.6 (P = 0.002); those scoring higher on helplessness had a lower risk of being so. DAS scores of high-pain responders were twice as high as those of low-pain responder (P = 0.043). During the first 2 min of CPT, the high-pain responders experienced more pain than the low-pain responders (P ≤ 0.029). Tooth pain thresholds did not differ between the two different pain responder groups. Pain catastrophising, dental anxiety and cold sensitivity appear to modify the pain experienced following placement of orthodontic separators. Further research is needed to determine the validity of screening questions to identify at-risk patients prior to commencing orthodontic treatment.

Influence of clinical experience on the radiographic determination of endodontic working length.

AIM: To determine the influence of clinical experience on the accuracy and consistency of estimation of radiographic working length (WL) for the root canal treatment of single-rooted teeth. METHODOLOGY: Forty conventional WL periapical radiographs that included variations in file length were selected. They were digitally scanned and arranged in PowerPoint presentations on CDs. These were distributed to three assessor groups; fourth-year undergraduates at two stages of training (Groups 1 and 2) and endodontic postgraduates (Group 3). Participants were asked to determine the adjustment needed in millimetres to position the file tip at the correct WL for each image. A gold standard file position was provided by three experienced endodontists. For inter-group comparison of scores, the Kruskal-Wallis, ANOVA and post hoc Bonferroni tests were used. Evaluation of intra-examiner consistency was with the Kappa test. To evaluate intra-group consistency, the Wilcoxon signed rank test was used to compare the frequency of weighted correct scorings. RESULTS: File adjustments of Group 3 were significantly more accurate than those of Group 1 (P = 0.006). The scores of Group 3 were also better than those of Group 2, although the difference was not significant. When the scores of the undergraduate groups were compared, the difference was not statistically significant. The consistency of the groups was not affected by a 2-week pause between assessments, and no definite pattern could be detected across any of the groups with the Kappa test. CONCLUSION: Clinical experience after graduation influenced the accuracy of estimating the adjustments needed for correct radiographic WL of single-rooted teeth. The most experienced group was significantly more accurate than the other groups.

Determination of working length for teeth with wide or immature apices: a review.

Practitioners face several challenges during the root canal treatment of teeth with wide or immature apices, one of which is working length determination. There is relatively little data regarding the value of radiography and electronic apex locator (EAL) use when root formation is incomplete, and supplementary measurement techniques may be helpful. This review considers length determination for canals with wide or completely open apices in permanent and primary teeth. The Ovid Medline, Web of Science and Scopus databases were searched individually and in combinations to August 2012 using the subject headings 'working length determination' and 'open apex' and revealed only one article. Further headings, 'tooth apex', 'apical constriction', 'resorption', 'foramen size', 'mature root apex', 'immature root apex', 'working length determination', 'apexification', 'open apices', 'open apex', 'open apical foramina', 'canal length determination', 'immature teeth', 'apical diameters', 'electronic apex locators', 'primary teeth', 'treatment outcome' and 'clinical outcome' were entered. Potentially useful articles were chosen for a manual search of bibliography as well as a forward search of citations. Other investigations revealed case reports and some research related to open apices and laboratory studies evaluating EALs, radiography and tactile methods. Some involved permanent teeth of various apical diameters and primary teeth with and without resorption. There is a need to define the term 'open apex'. Clinicians should be aware of the benefits and limitations of all canal measuring techniques involved in managing this problem.

Effect of restorations on pulpal blood flow in molars measured by laser Doppler flowmetry.

AIM: To: (i) compare laser Doppler pulpal blood flow (PBF) signals from restored and unrestored first molar teeth, (ii) investigate PBF in teeth with large and small restorations, and (iii) to relate PBF to pulp chamber dimensions on radiographs. METHODOLOGY: Bitewing radiographs of young adults with restored first molars were obtained and pulp chamber dimensions measured. Subjects were divided into 2 groups: group A with a restored tooth and an unrestored contralateral (43 subjects) and group B, those with a molar with a small (usually occlusal) restoration whilst the contralateral tooth had an extensive occlusal restoration (or restorations) or restored proximal surface(s) and/or cuspal overlay (31 subjects). The 148 teeth responded to electric pulp testing, and their PBF was recorded using a laser Doppler flowmeter. Data were analysed using Student's t-test. RESULTS: In group A the PBF in the restored teeth was significantly lower than in unrestored contralaterals (P = 0.028) and the total pulp chamber area and that in the clinical crown were smaller (P = 0.039 and 0.021 respectively). The group B molars with large restorations had significantly lower PBF than contralaterals with small restorations (P = 0.001), and their total pulp chamber area and pulp chamber width at cervix were reduced significantly (P = 0.003 and 0.032 respectively). CONCLUSIONS: In molars the size of the pulp chamber was influenced by the presence of restorations and the PBF was reduced when restorations were present. Size and extent of restorations had a significant effect on PBF.

The smear layer in endodontics - a review.

Root canal instrumentation produces a layer of organic and inorganic material called the smear layer that may also contain bacteria and their by-products. It can prevent the penetration of intracanal medicaments into dentinal tubules and influence the adaptation of filling materials to canal walls. This article provides an overview of the smear layer, focusing on its relevance to endodontics. The PubMed database was used initially; the reference list for smear layer featured 1277 articles, and for both smear layer dentine and smear layer root canal revealed 1455 publications. Smear layer endodontics disclosed 408 papers. A forward search was undertaken on selected articles and using some author names. Potentially relevant material was also sought in contemporary endodontic texts, whilst older books revealed historic information and primary research not found electronically, such that this paper does not represent a 'classical' review. Data obtained suggests that smear layer removal should enhance canal disinfection. Current methods of smear removal include chemical, ultrasonic and laser techniques - none of which are totally effective throughout the length of all canals or are universally accepted. If smear is to be removed, the method of choice seems to be the alternate use of ethylenediaminetetraacetic acid and sodium hypochlorite solutions. Conflict remains regarding the removal of the smear layer before filling root canals, with investigations required to determine the role of the smear layer in the outcomes of root canal treatment.

Pulp stones: a review.

Pulp stones are a frequent finding on bitewing and periapical radiographs but receive relatively little attention in textbooks. A review of the literature was therefore performed, initially using the PubMed database and beginning the search with 'pulp calcifications' and 'pulp stones'. Each term provided more than 400 references, many of which related to pulp calcification in general rather than pulp stones, and focussed largely on the problems these changes presented to clinicians. A manual search using references from this source was carried out. Contemporary textbooks in endodontology were also consulted, and an historic perspective gained from a number of older books and references. The factors involved in the development of the pulp stones are largely unknown. Further research may determine the reasons for their formation, but with current endodontic instruments and techniques this is unlikely to alter their relevance to clinicians.

Electric pulp testing: a review.

Electric pulp testing (EPT) has been available for more than a century and used in dental practices worldwide. This article provides an overview of this diagnostic aid. The PubMed database from 1953 was used initially; the reference list for pulp testing featured 1071 articles, and for EPT identified 121 papers. A forward search was undertaken on these articles and using selected author names. Potentially relevant material was also sought in contemporary endodontic texts, while older textbooks on endodontics, operative dentistry and pain revealed historic information and primary research not found electronically. A short account of the innervation of the pulp is followed by an historic overview. Clinical considerations discussed include tooth isolation, glove wearing and tester electrode placement. Orthodontic treatment, pacemaker wearing and patient medications are considered. Research applications are also discussed. While EPT is valuable, no single pulp testing technique can reliably diagnose all pulp conditions. Careful collection of patient history regarding the problem tooth and prudent use of appropriate radiographs are also helpful. The shortcomings of electric tests, especially in the case of immature and concussed teeth, must be understood. The demeanour of the patient and the responses given by control teeth also require careful consideration.

Orthodontic movement of two root fractured teeth: a case report.

AIM: To illustrate significant tipping orthodontic movement of root fractured teeth. SUMMARY: As the frequency of root fractured maxillary teeth is related to increased overjet and reduced lip coverage, orthodontic treatment may increase lip coverage and reduce the risk of trauma or its severity. It may also be necessary to move previously traumatized teeth. Two root fractured teeth were tipped through a considerable angle (19 degrees ) to reduce a large overjet and followed up for 5 years. KEY LEARNING POINTS: -- Reduction of large overjets involving root fractured teeth may not affect pulp vitality. -- Root fragment separation prior to orthodontics did not appear to increase in this patient, but angulation of the fragments did not completely follow the major change to the coronal part of the tooth.

An evaluation of .06 tapered gutta-percha cones for filling of .06 taper prepared curved root canals.

AIM: To compare the area occupied by gutta-percha, sealer, or void in standardized .06 tapered prepared simulated curved canals and in mesio-buccal canals of extracted maxillary first molars filled with a single .06 gutta-percha point and sealer or lateral condensation of multiple .02 gutta-percha points and sealer. METHODOLOGY: Simulated canals in resin blocks with either a 30 degrees curve and radius of 10.5 mm (n = 20) or a 58 degrees curve and 4.7 mm radius (n = 20) and curved mesio-buccal canals of extracted maxillary first molars (n = 20) were prepared using .06 ProFiles in a variable tip crown-down sequence to an apical size 35 at 0.5 mm from the canal terminus or apical foramen. Ten 30 degrees and 58 degrees curved resin canals and 10 canals in the extracted teeth group were obturated with .02 taper gutta-percha cones and AH 26 sealer using lateral condensation. The time required to obturate was recorded. The remaining canals were obturated with a single .06 taper gutta-percha cone and AH 26 sealer. Excess gutta-percha was removed from the specimens using heat and the warm mass vertically condensed. Horizontal sections were cut at 0.5, 1.5, 2.5, 4.5, 7.5 and 11.5 mm from the canal terminus or apical foramen. Colour photographs were taken using an Olympus 35 mm camera attached to a stereomicroscope set at x40 magnification, and then digitized using a flatbed scanner. The cross-sectional area of the canal contents was analysed using Adobe PhotoShop. The percentage of gutta-percha, sealer or voids to the total root canal area were derived and data analysed using unpaired Student's t-test and the Mann-Whitney U-test. RESULTS: In the 30 degrees curved canals the levels had between 94 and 100% of the area filled with gutta-percha with no significant difference (P > 0.05) between the lateral condensation and single cone techniques. In the 58 degrees curved canals the levels had 92-99% of the area filled with gutta-percha, with the single cone technique having significantly (P < 0.05) more gutta-percha fill at the 2.5 mm level only. In the mesio-buccal canals of the teeth the levels had between 72 and 96% of the area filled with gutta-percha with no significant difference (P > 0.05) between the lateral condensation and single cone technique. The time for obturation was significantly (P < 0.05) greater for lateral condensation compared with the single cone technique in all groups. CONCLUSIONS: The .06 taper single cone technique was comparable with lateral condensation in the amount of gutta-percha occupying a prepared .06 tapered canal. The .06 single cone technique was faster than lateral condensation.

Clarity and diagnostic quality of digitized conventional intraoral radiographs.

OBJECTIVES: To compare digital images of conventional radiographs with the original radiographs for perceived clarity of endodontic files, periapical lesions and carious lesions, and to establish the diagnostic value of the digital images. METHODS: Four groups of ten radiographs were used: standardized bitewings demonstrating carious lesions, periapical radiographs of apical lesions, periapical radiographs showing endodontic files of various sizes at working length, and standardized periapical radiographs with size 08 files at working length. Radiographs were photographed using an Olympus C 2500-L digital camera and a Nikon D1X digital camera and were scanned using a Nikon Supercoolscan 4000 ED film/slide scanner. The digital images were then transferred to a Toshiba Satellite 2210 laptop. Three general dental practitioners compared each conventional radiograph with the three matching digital images. Images were ranked for clarity and were assessed for diagnostic quality. Data were analysed using General Estimating Equations. RESULTS: The clarity and diagnostic quality of the conventional radiographs were superior to the digital images produced by the three techniques (P < 0.001). No significant difference was found between the Nikon D1X and Camedia 2500-L cameras for clarity or diagnostic quality. The scanner was equivalent to the Camedia 2500-L camera for diagnostic quality, but was otherwise inferior to both cameras. CONCLUSIONS: Digitizing conventional radiographs using current high-grade digital cameras or scanners does not produce images of diagnostic quality. Improved resolution of viewing monitors is necessary to fully harness the potential of digital technology.

Pulp size in molars: underestimation on radiographs.

The aim was to determine whether radiographs provide a clinically useful indication of pulp size in diseased/restored human first molar teeth, and to investigate accessibility of pulp tissue for diagnostic testing using laser Doppler flowmetry (LDF). Extracted teeth of known age were collected. Restorative materials were removed and teeth with evidence of pulp exposures excluded. Fifty-six teeth were radiographed from buccal and mesial aspects, and then their crowns were sectioned axiobuccolingually and photographed. Images were digitally scanned and measurements made of the total pulp area (above a line across the most superior part of the pulpal floor) and the pulp area in the clinical crown (superior to a line between the amelocemental junctions). The pulp width at the cervix and the highest point of the pulp were also recorded. Data were analysed using Pearson correlations. Pulp areas within the clinical crowns were significantly larger than indicated by radiographs, by 23% in the case of the clinically attainable buccal view (P < 0.05). Pulps may be more accessible to flowmeter testing than they appear. Absence of pulp tissues in the crown was recorded in equal numbers of teeth on radiographs and sections, but with agreement for only one tooth. Sixteen per cent of the teeth had no pulp area in the clinical crown when sectioned, but might still be suitable for testing using LDF.

The bitewing radiograph as an assessment tool in fixed prosthodontics.

Molar crown preparations, as described in the literature, have standard forms dictated by the demands of retention, resistance and the physical properties of materials. Standard designs may not be appropriate for all patients because of ethnic variations in tooth shape, pulp size and dentine thickness. Accurate data on these features could assist clinicians to minimize the risk of accidental pulpal injury. The aim of this study was to compare the first molar crown and pulp dimensions between Asian (Chinese, Korean, Malay) and other ethnic groups, using measurements from the bitewing radiographs of 121 subjects. Comparisons revealed the following significantly different features of Asian first molars: larger total pulp areas in uppers (P < 0.0005); shorter crowns (P < 0.0005); narrower upper teeth at the cervix (P < 0.0005); wider pulps at the cervix of lowers (P < 0.02); more bulbous crowns (P < 0.0005 for uppers; P < 0.01 for lowers), and finally significantly thinner dentine interproximally at the cervix (P=0.001 for uppers; P=0.011 for lowers). Preparations with wide shoulders could pose hazards to the pulps in Asian subjects. This study emphasizes the value of bitewing films in assessing crown and pulp size and shape before making crown preparations. The experienced practitioner may intuitively include tooth and pulp morphology in treatment planning, but this appears not to be taught or documented in textbooks.

Electronic apex locators.

Prior to root canal treatment at least one undistorted radiograph is required to assess canal morphology. The apical extent of instrumentation and the final root filling have a role in treatment success, and are primarily determined radiographically. Electronic apex locators reduce the number of radiographs required and assist where radiographic methods create difficulty. They may also indicate cases where the apical foramen is some distance from the radiographic apex. Other roles include the detection of root canal perforation. A review of the literature focussed first on the subject of electronic apex location. A second review used the names of apex location devices. From the combined searches, 113 pertinent articles in English were found. This paper reviews the development, action, use and types of electronic apex locators.

Coronal pulp size in molars: a study of bitewing radiographs.

AIM: To: (i) study coronal pulp dimensions in human first molar teeth; (ii) investigate the effects of restorations on pulp size; (iii) determine differences in dimensions between teeth of Mongoloid patients and teeth of other ethnic groups; and (iv) record the presence of pulp stones. METHODOLOGY: Bitewing radiographs of 121 subjects (mean age, 20.9 years) were taken under standardized conditions. The films were digitally scanned and nine measurements were made from the image of each first molar. The data were analysed in terms of presence or absence of restorations and in terms of racial group. Differences were examined using Student's t-test, Pearson correlations and Levene's test. RESULTS: A total of 445 teeth were analysed. Large crowns were correlated to large pulps. Teeth restored with occlusal and proximal restorations had significantly smaller pulps (P = 0.044 and 0.004, respectively), but no difference was found in pulp area in the clinical crown between the restoration types. Mongoloid crowns were shorter and more bulbous. Pulp areas of maxillary molars and pulp widths at the cervix of mandibular molars were significantly larger in Mongoloids. The pulp area in the clinical crown correlated to pulp horn height for Mongoloids and others and for maxillary and mandibular teeth. No differences were found between the heights of pulp horns in the Mongoloid and other teeth. Four of the pulp measurements demonstrated sexual dimorphism. Stones were present in almost 10% of the subjects, representing 4% of the tooth pulps examined. CONCLUSION: Even teeth with shallow occlusal restorations had reduced pulp spaces. There were significant differences in pulp and crown dimensions between the teeth of Mongoloid patients and those of other patients.

Factors influencing the removal of posts.

AIM: To determine whether metal type, cement type and the use of ultrasonic vibration influence the amount of tensile force required to remove parallel-sided, prefabricated, metal posts from tooth roots. METHODOLOGY: Ninety extracted canine teeth were sectioned horizontally 1-mm coronal to the labial cemento-enamel junction and embedded in acrylic blocks. Standardized post spaces were prepared with a ParaPost no. 5 (1.25 mm) drill to 10 mm and ParaPost XP no. 5 stainless steel and titanium posts were cemented using zinc phosphate, glass ionomer or composite resin cement. Sixty posts were subjected to 16 min of ultrasonic vibration whilst 30 stainless steel posts received no vibration. The force required for post removal was determined using a universal testing machine. Results were analysed using univariate anova. RESULTS: The univariate anova revealed no statistically significant differences between the groups at the P = 0.05 level. CONCLUSIONS: In this in vitro experiment, metal type, cement type and ultrasonic vibration did not influence the force required to remove posts.

Effect of X-ray beam angulation and intraradicular contrast medium on radiographic interpretation of lower first molar root canal anatomy.

AIMS: To compare evaluator radiographic interpretation of noncontrasted and contrasted root canal anatomy on radiographs taken at a 0 or 30 degrees mesial angle to the orthoradial orientation. METHODOLOGY: Pulp tissue was removed from 20 mandibular first molar teeth using NaOCl irrigation and hand files. Standardized radiographs at 0 and 30 degrees angulation were obtained of each tooth positioned in a dried mandible. Contrast medium (iohexol) was injected passively into the canals and a second pair of corresponding radiographs was obtained. A third pair of radiographs was taken after infusing canals under vacuum with contrast medium. Using set criteria, three evaluators assessed the canal anatomy of the mesial root on radiographs: (i) the number of visible canals, (ii) whether the canal(s) was visible along the entire length of the root, (iii) the location of the canal terminus in relation to the radiographic apex, (iv) configuration of canal(s), (v) level of multiple canals merging and (vi) the presence of lateral canals. The teeth were then cleared for visual assessment. The data were compared using logistic regression and the intra- and interevaluator reliability assessed with the Kappa test. RESULTS: Noncontrasted 0 degrees images were significantly better (P < 0.05) than noncontrasted 30 degrees images for detecting the number of visible canals, whether the canal(s) was visible along the entire length of the root, the location of the canal terminus in relation to the radiographic apex and level of multiple canals merging. The 0 degrees images contrasted by vacuum or passive injection were significantly better (P < 0.05) than 30 degrees images only for assessing whether the canal(s) was visible along the entire length of the root, whilst the 0 degrees image contrasted by passive injection was also better (P < 0.05) at assessing the location of the canal terminus in relation to the radiographic apex. At 30 degrees, contrast medium passively or vacuum introduced improved (P < 0.05) the detection of the number of visible canals, whether the canal(s) was visible along the entire length of the root and configuration of canal(s), whilst vacuum also improved (P < 0.05) the location of the canal terminus in relation to the radiographic apex. Overall, there was no significant difference (P > 0.05) between images contrasted by passive injection or vacuum. CONCLUSIONS: Under the conditions of this study, conventional radiographs taken at a 0 degrees orientation provided more information than 30 degrees radiographs. Contrast medium improved radiographic interpretation of canal anatomy, especially when used with 30 degrees radiographs.