Tailoring of the Structural, Optical, and Electrical Characteristics of Sol-Gel-Derived Magnesium-Zinc-Oxide Wide-Bandgap Semiconductor Thin Films via Gallium Doping.

The Ga-doped Mg0.2Zn0.8O (GMZO) transparent semiconductor thin films were prepared using the sol-gel and spin-coating deposition technique. Changes in the microstructural features, optical parameters, and electrical characteristics of sol-gel-synthesized Mg0.2Zn0.8O (MZO) thin films affected by the amount of Ga dopants (0-5 at%) were studied. The results of grazing incidence X-ray diffraction (GIXRD) examination showed that all as-prepared MZO-based thin films had a wurtzite-type structure and hexagonal phase, and the incorporation of Ga ions into the MZO nanocrystals refined the microstructure and reduced the average crystallite size and flatness of surface roughness. Each glass/oxide thin film sample exhibited a higher average transmittance than 91.5% and a lower average reflectance than 9.1% in the visible range spectrum. Experimental results revealed that the optical bandgap energy of the GMZO thin films was slightly higher than that of the MZO thin film; the Urbach energy became wider with increasing Ga doping level. It was found that the 2 at% and 3 at% Ga-doped MZO thin films had better electrical properties than the undoped and 5 at% Ga-doped MZO thin films.

Permeate Flux Enhancement in Air Gap Membrane Distillation Modules with Inserting Λ-Ribs Carbon-Fiber Open Slots.

A novel design of an air gap membrane distillation (AGMD) module was proposed to enhance the permeate flux improvement for the desalination of pure water productivity. The modeling equations for predicting permeate flux in the AGMD module by inserting Λ-ribs carbon-fiber open slots under various hydrodynamic angles were developed theoretically and experimentally. The temperature distributions of both hot and cold feed streams were represented graphically with the hot saline flow rate, inlet saline temperature, and carbon-fiber hydrodynamic angles as parameters. The results showed a good agreement between the experimental results and theoretical predictions. Designed by inserting Λ-ribs carbon-fiber open slots into the flow channel, the membrane distillation module was implemented to act as an eddy promoter and yield an augmented turbulence flow. The effect of Λ-ribs carbon-fiber open slots not only assured the membrane stability by preventing vibration but also increased the permeate flux by diminishing the temperature polarization of the thermal boundary layer. The permeate flux improvement by inserting Λ-ribs carbon-fiber open slots in the AGMD module provided the maximum relative increment of up to 15.6% due to the diminution of the concentration polarization effect. The experimental data was incorporated with the hydrodynamic angle of Λ-ribs carbon-fiber open slots to correlate the enhancement factor with the Nusselt numbers to confirm the theoretical predictions. The accuracy derivation between the experimental results and theoretical predictions was pretty good, within 9.95≤E≤1.85. The effects of operating and designing parameters of hot saline flow rate, inlet saline temperature, and hydrodynamic angle on the permeate flux were also delineated by considering both the power consumption increment and permeate flux enhancement.

Defined cell adhesion for silicon-based implant materials by using vapor-deposited functional coatings.

The field of implantable electronics relies on using silicon materials due to the merits of a well-established fabrication process and favorable properties; of particular interest is the surface modification of such materials. In the present study, we introduce a surface modification technique based on coatings of functionalized Parylene on silicon substrates, where the modified layers provide a defined cell adhesion capability for the resultant silicon materials/devices. Functionalization of Parylene was achieved during a one-step chemical vapor deposition (CVD) polymerization process, forming NHS ester-functionalized Parylene, and subsequent RGD attachment was enabled via a conjugation reaction between the NHS ester and amine groups. The modification procedures additionally provided a clean and gentle approach to avoid thermal excursions, intense irradiation, chemicals, or solvents that might damage delicate structures or sensitive molecules on the devices. The modification layers exhibited excellent mechanical strength on the substrate, meeting the high standards of the American Society for Testing and Materials (ASTM), and the resultant cell adherence property was verified by a centrifugation assay and the analysis of attached cell morphologies; the results collectively demonstrated robust and sustainable modification layers of the NHS ester-functionalized Parylene and confirmed that the cell-adherence property imparted by using this facile modification technique was effective. The modification technology is expected to benefit the design of prospective interface properties for silicon-based devices and related industrial products.

Sensing acidosis: nociception or sngception?

BACKGROUND: Sensing tissue acidosis is an important function of the somatosensory nervous system to response to noxious stimuli. MAIN BODY: In the pain clinic, acid or soreness sensation is a characteristic sensory phenotype of various acute and chronic pain syndromes, such as delayed onset muscle soreness, fibromyalgia, and radicular pain. However, soreness sensation is a sign of successful analgesia for acupuncture and noxipoint therapy. Thus, the nature of acid or soreness sensation is not always nociceptive (or painful) and could be anti-nociceptive. To facilitate the investigation of the molecular and neurobiological mechanisms of soreness sensation, we propose a concept called "sngception (sng- ception)" to describe the response of the somatosensory nervous system to sense tissue acidosis and to distinguish it from nociception. "Sng" is a Taiwanese word that represents the state of soreness while at the same time imitates the natural vocalization of humans feeling sore. CONCLUSION: Here we propose sngception as a specific somatosensory function that transmits the acid sensation from the peripheral to the central nervous system. Sngception could partially overlap with nociception, but it could also transmit antinociception, proprioception, and pruriception.

Enhanced Growth Activities of Stem Cell Spheroids Based on a Durable and Chemically Defined Surface Modification Coating.

Surface modification layers are needed for the precise definition of surface chemistries and are equally important for durable and stable adhesive properties to ensure long-term stability and effective performance for biotechnological applications. This study demonstrates a robust modification layer that is synthesized based on chemical vapor deposition copolymerization, and the resultant coating layer is composed of the side-by-side presentation of N-hydroxysuccinimide ester and maleimide functionalities with a controlled ratio to define the immobilization accessibility of chitosan and growth factor protein (FGF-2) molecules on the substrate surface for enhancing cellular activities of stem cells. Characterizations of the copolymer modification layer showed excellent durability, including adhesive strength and thermal stability, and the layer is free of concerns for delamination and/or unacceptable deformation/debris formation that can cause potential toxicity to the surrounding biological environment. Modifications using the copolymer layer on the cell culture surface have demonstrated synergistic activity by chitosan to support the formation of spheroids and by FGF-2 to enhance the proliferation of human adipose-derived stem cells (ADSCs) within the spheroids while increasing the spheroid size and cell numbers. Healthy and flourishing growth activities were discovered for ADSCs on the modified culture surfaces, and the results are useful for potential and related stem cell research and the interfaces of biomaterials.

Fabrication of Functional Polymer Structures through Bottom-Up Selective Vapor Deposition from Bottom-Up Conductive Templates.

An electrically induced bottom-up process was introduced for the fabrication of multifunctional nanostructures of polymers. Without requiring complicated photolithography or printing techniques, the fabrication process first produced a conducting template by colloidal lithography to create an interconnected conduction pathway. By supplying an electrical charge to the conducting network, the conducting areas were enabled with a highly energized surface that generally deactivated the adsorbed reactive species and inhibited the vapor deposition of poly- p-xylylene polymers. However, the template allowed the deposition of ordered poly- p-xylylene nanostructures only on the confined and negative areas of the conducting template, in a relatively large centimeter-scale production. The wide selection of functionality and multifunctional capability of poly- p-xylylenes naturally rendered the synergistic and orthogonal chemical reactivity of the resulting nanostructures. With only a few steps, the construction of a nanometer topology with the functionalization of multiple chemical conducts can be achieved, and the selected deposition process represents a state-of-the-art nanostructure fabrication in a simple and versatile approach from the bottom up.

Development of Antifouling Hyperbranched Polyglycerol Layers on Hydroxyl Poly-p-xylylene Coatings.

Antifouling surfaces that are resistant to protein adsorption and cell adhesion are desirable for many biomedical devices, such as diagnostic devices, biosensors, and implants. In this study, we developed an antifouling hyperbranched polyglycerol (hPG) surface on hydroxyl poly-p-xylylene (PPX-OH). PPX-OH was deposited via chemical vapor deposition (CVD), and an hPG film was then developed via the ring-opening reaction of glycidol. The hPG film greatly reduced the adhesion of L929 cells and platelets as well as protein adsorption. The addition of alkenyl groups in the hPG layer allows the conjugation of biomolecules, such as peptides and biotin, and elicits specific biological interactions. Since the CVD deposition of PPX-OH could be applied to most types of materials, our approach makes it possible to decorate an antifouling hPG film on most types of materials. Our method could be applied to biosensors, diagnostics, and biomedical devices in the future.

Synergistic effects between TiO2 and carbon nanotubes (CNTs) in a TiO2/CNTs system under visible light irradiation.

This study synthesized a TiO2/carbon nanotubes (CNTs) composite via the sol-gel method. The surface characteristics of the TiO2/CNTs composite were determined by X-ray diffraction, transmission electron microscopy, specific surface area analyser, ultraviolent (UV)-vis spectroscopy, X-ray photoelectron spectroscopy and Raman spectrometer. The photocatalytic activity ofthe TiO2/CNTs composite was evaluated by decolourizing C.I. Reactive Red 2 (RR2) under visible light irradiation. Furthermore, the effects of calcination temperature, pH, RR2 concentration, and the TiO2/CNTs composite dosage on RR2 decolourization were determined simultaneously. The optimal calcination temperature to generate TiO2 and the TiO2/CNTs composite was 673 K, as the percentage of anatase crystallization at this temperature was highest. The specific surface area of the TiO2/CNTs composite and TiO2 were 45 and 42 m2/g, respectively. The band gap of TiO2 and the TiO2/CNTs composite was 2.97 and 2.71 eV by UV-vis measurements, respectively. Experimental data indicate that the Ti-O-C bond formed in the TiO2/CNTs composite. The RR2 decolourization rates can be approximated by pseudo-first-order kinetics; moreover, only the TiO2/CNTs composite had photocatalytic activity under visible light irradiation. At pH 7, the RR2 decolourization rate constant of 0.5, 1 and 2 g/L TiO2/CNTs addition was 0.005, 0.0015, and 0.0047 min(-1), respectively. Decolourization rate increased as pH and the RR2 concentration decreased. The CNTs functioned as electron acceptors, promoting separation of photoinduced electron-hole pairs to retard their recombination; thus, photocatalytic activity of the TiO2/CNTs composite exceeded that of TiO2.

A new bias field correction method combining N3 and FCM for improved segmentation of breast density on MRI.

PURPOSE: Quantitative breast density is known as a strong risk factor associated with the development of breast cancer. Measurement of breast density based on three-dimensional breast MRI may provide very useful information. One important step for quantitative analysis of breast density on MRI is the correction of field inhomogeneity to allow an accurate segmentation of the fibroglandular tissue (dense tissue). A new bias field correction method by combining the nonparametric nonuniformity normalization (N3) algorithm and fuzzy-C-means (FCM)-based inhomogeneity correction algorithm is developed in this work. METHODS: The analysis is performed on non-fat-sat T1-weighted images acquired using a 1.5 T MRI scanner. A total of 60 breasts from 30 healthy volunteers was analyzed. N3 is known as a robust correction method, but it cannot correct a strong bias field on a large area. FCM-based algorithm can correct the bias field on a large area, but it may change the tissue contrast and affect the segmentation quality. The proposed algorithm applies N3 first, followed by FCM, and then the generated bias field is smoothed using Gaussian kernal and B-spline surface fitting to minimize the problem of mistakenly changed tissue contrast. The segmentation results based on the N3+FCM corrected images were compared to the N3 and FCM alone corrected images and another method, coherent local intensity clustering (CLIC), corrected images. The segmentation quality based on different correction methods were evaluated by a radiologist and ranked. RESULTS: The authors demonstrated that the iterative N3+FCM correction method brightens the signal intensity of fatty tissues and that separates the histogram peaks between the fibroglandular and fatty tissues to allow an accurate segmentation between them. In the first reading session, the radiologist found (N3+FCM > N3 > FCM) ranking in 17 breasts, (N3+FCM > N3 = FCM) ranking in 7 breasts, (N3+FCM = N3 > FCM) in 32 breasts, (N3+FCM = N3 = FCM) in 2 breasts, and (N3 > N3+FCM > FCM) in 2 breasts. The results of the second reading session were similar. The performance in each pairwise Wilcoxon signed-rank test is significant, showing N3+FCM superior to both N3 and FCM, and N3 superior to FCM. The performance of the new N3+FCM algorithm was comparable to that of CLIC, showing equivalent quality in 57/60 breasts. CONCLUSIONS: Choosing an appropriate bias field correction method is a very important preprocessing step to allow an accurate segmentation of fibroglandular tissues based on breast MRI for quantitative measurement of breast density. The proposed algorithm combining N3+FCM and CLIC both yield satisfactory results.

Controlling pore morphology and properties of nanoporous silica films using the different architecture PS-b-P2VP as a template.

Nanoporous silica films were prepared through the templating of amphiphilic block copolymer, poly(styrene-2-vinyl pyridine) (PS-b-P2VP), and monodispersed colloidal silica nanoparticles. The experimental and theoretical studies suggested that the intermolecular hydrogen bonding existes between the colloidal silica nanoparticles and PS-b-P2VP. The effects of the loading ratio and P2VP chain length on the morphology and properties of the prepared nanoporous silica films were investigated. TEM and AFM studies showed that the uniform pore size could be achieved and the pore size increased with increasing porogen loading. The refractive index and dielectric constant of the prepared nanoporous films decreased with an increase in PS-b-P2VP loading. On the other hand, the porosity increased with an increasing PS-b-P2VP loading. This study demonstrated a methodology to control pore morphology and properties of the nanoporous silica films through the templating of PS-b-P2VP.