Ultrathin, Mechanically Robust Quasi-Solid Composite Electrolyte for Solid-State Lithium Metal Batteries.

Herein, we present the preparation and properties of an ultrathin, mechanically robust, quasi-solid composite electrolyte (SEO-QSCE) for solid-state lithium metal battery (SLB) from a well-defined polystyrene-b-poly(ethylene oxide) diblock copolymer (SEO), Li6.75La3Zr1.75Ta0.25O12 nanofiller, and fluoroethylene carbonate plasticizer. Compared with the ordered lamellar microphase separation of SEO, the SEO-QSCE displays bicontinuous phases, consisting of a Li+ ion conductive poly(ethylene oxide) domain and a mechanically robust framework of the polystyrene domain. Therefore, the 12 µm-thick SEO-QSCE membrane exhibits an exceptional ionic conductivity of 1.3 × 10-3 S cm-1 at 30 °C, along with a remarkable tensile strength of 5.1 MPa and an elastic modulus of 2.7 GPa. The high mechanical robustness and the self-generated LiF-rich SEI enable the SEO-QSCE to have an extraordinary lithium dendrite prohibition effect. The SLB of Li|SEO-QSCE|LiFePO4 reveals superior cycling performances at 30 °C for over 600 cycles, maintaining an initial discharge capacity of 145 mAh g-1 and a remarkable capacity retention of 81% (117 mAh g-1) after 400 cycles at 0.5 C. The high-voltage SLB of Li|SEO-QSCE|LiNi0.5Co0.3Mn0.2O2 displays good cycling stability for over 150 cycles at 30 °C. Moreover, the exceptional robustness of SEO-QSCE enables the high-voltage solid-state pouch cell of Li|SEO-QSCE|LiNi0.5Co0.3Mn0.2O2 with high flexibility and excellent safety features. The current investigation delivers a promising and innovative approach for preparing quasi-solid electrolytes with features of ultrathin design, mechanical robustness, and exceptional electrochemical performance for high-voltage SLBs.

Insight into Multiple Intermolecular Coordination of Composite Solid Electrolytes via Cryo-Electron Microscopy for High-Voltage All-Solid-State Lithium Metal Batteries.

Polymer/ceramic-based composite solid electrolytes (CSE) are promising candidates for all-solid-state lithium metal batteries (SLBs), benefiting from the combined mechanical robustness of polymeric electrolytes and the high ionic conductivity of ceramic electrolytes. However, the interfacial instability and poorly understood interphases of CSE hinder their application in high-voltage SLBs. Herein, a simple but effective CSE that stabilizes high-voltage SLBs by forming multiple intermolecular coordination interactions between polyester and ceramic electrolytes is discovered. The multiple coordination between the carbonyl groups in poly(ε-caprolactone) and the fluorosulfonyl groups in anions with Li6.5La3Zr1.5Ta0.5O12 nanoparticles is directly visualized by cryogenic transmission electron microscopy and further confirmed by theoretical calculation. Importantly, the multiple coordination in CSE not only prevents the continuous decomposition of polymer skeleton by shielding the vulnerable carbonyl sites but also establishes stable inorganic-rich interphases through preferential decomposition of anions. The stable CSE and its inorganic-rich interphases enable Li||Li symmetric cells with an exceptional lifespan of over 4800 h without dendritic shorting at 0.1 mA cm-2. Moreover, the high-voltage SLB with LiNi0.5Co0.2Mn0.3O2 cathode displays excellent cycling stability over 1100 cycles at a 1C charge/discharge rate. This work reveals the underlying mechanism behind the excellent stability of coordinating composite electrolytes and interfaces in high-voltage SLBs.

Regulating Electrolyte Solvation Structures via Diluent-Solvent Interactions for Safe High-Voltage Lithium Metal Batteries.

Local high concentration electrolytes (LHCEs) have been proved to be one of the most promising systems to stabilize both high voltage cathodes and Li metal anode for next-generation batteries. However, the solvation structures and interactions among different species in LHCEs are still convoluted, which bottlenecks the further breakthrough on electrolyte development. Here, it is demonstrated that the hydrogen bonding interaction between diluent and solvent is crucial for the construction of LHCEs and corresponding interphase chemistries. The 2,2,2-trifluoroethyl trifluoromethane sulfonate (TFSF) is selected as diluent with the solvent dimethoxy-ethane (DME) to prepare a non-flammable LHCE for high voltage LMBs. This is first find that the hydrogen bonding interaction between TFSF and DME solvent tailors the electrolyte solvation structures by weakening the coordination of DME molecules to Li+ cations and allows more participation of anions in the first solvation shell, leading to the formation of aggregates (AGGs) clusters which are conducive to generating inorganic solid/cathodic electrolyte interphases (SEI/CEIs). The proposed TFSF based LHCE enables the Li||NCM811 (LiNi0.8 Mn0.1 O2 ) batteries to realize >80% capacity retention with a high average Coulombic efficiency of 99.8% for 230 cycles under aggressive conditions (NCM811 cathode: 3.4 mAh cm-2 , cut-off voltage: 4.4 V, and 20 µm Li foil).

Beyond LiF: Tailoring Li2O-Dominated Solid Electrolyte Interphase for Stable Lithium Metal Batteries.

The components and structures of the solid-electrolyte interphase (SEI) are critical for stable cycling of lithium metal batteries (LMBs). LiF has been widely studied as the dominant component of SEI, but Li2O, which has a much lower diffusion barrier for Li+, has rarely been investigated as the dominant component of SEI. The effect of Li2O-dominated SEI on electrochemical performance still remains elusive. Herein, an ultrastrong coordinated cosolvation diluent, 2,3-difluoroethoxybenzene (DFEB), is designed to modulate solvation structure and tailor Li2O-dominated SEI for stable LMBs. In the DFEB-based LHCE (DFEB-LHCE), DFEB intensively participates in the first solvation shell and synergizes with FSI- to tailor an Li2O-dominated inorganic-rich SEI which is different from the LiF-dominated SEI formed in conventional LHCE. Benefiting from this special SEI architecture, a high Coulombic efficiency (CE) of 99.58% in Li||Cu half cells, stable voltage profiles, and dense and uniform lithium deposition, as well as effective inhibition of Li dendrite formation in the symmetrical cell, are achieved. More importantly, the DFEB-LHCE can be matched with various cathodes such as LFP, NCM811, and S cathodes, and the Li||LFP full cell using DFEB-LHCE possesses 85% capacity retention after 650 stable cycles with 99.9% CE. Especially the 1.5 Ah practical lithium metal pouch cell achieves an excellent capacity retention of 89% after 250 cycles with a superb average CE of 99.93%. This work unravels the superiority of the Li2O-dominated SEI and the feasibility of tailoring SEI components through modulation of solvation structures.

Fundamentals of the Cathode-Electrolyte Interface in All-solid-state Lithium Batteries.

All-solid-state lithium batteries (ASSBs) enabled by solid-state electrolytes (SEs) including oxide-based and sulfide-based electrolytes have gained worldwide attention because of their intrinsic safety and higher energy density over conventional lithium-ion batteries (LIBs). However, despite the high ionic conductivity of advanced SEs, ASSBs still exhibit high overall internal resistance, the most significant contributor of which can be ascribed to the cathode-SE interfaces. This review seeks to clarify the critical issues regarding the cathode-SE interfaces, including fundamental principles and corresponding solutions. First, major issues concerning electro-chemo-mechanical instability between cathodes and SEs and their formation mechanisms are discussed. Then, specific problems in oxides and sulfides and various solutions and strategies toward interfacial modifications are highlighted. Efforts toward the characterization and analysis of cathode-SE interfaces with advanced techniques are also summarized. Finally, perspectives are offered on several problems demanding urgent solutions and the future development of SE applications and ASSBs.

Roll-To-Roll Fabrication of Zero-Volume-Expansion Lithium-Composite Anodes to Realize High-Energy-Density Flexible and Stable Lithium-Metal Batteries.

The lithium (Li)-metal anode offers a promising solution for high-energy-density lithium-metal batteries (LMBs). However, the significant volume expansion of the Li metal during charging results in poor cycling stability as a result of the dendritic deposition and broken solid electrolyte interphase. Herein, a facile one-step roll-to-roll fabrication of a zero-volume-expansion Li-metal-composite anode (zeroVE-Li) is proposed to realize high-energy-density LMBs with outstanding electrochemical and mechanical stability. The zeroVE-Li possesses a sandwich-like trilayer structure, which consists of an upper electron-insulating layer and a bottom lithiophilic layer that synergistically guides the Li deposition from the bottom up, and a middle porous layer that eliminates volume expansion. This sandwich structure eliminates dendrite formation, prevents volume change during cycling, and provides outstanding flexibility to the Li-metal anode even at a practical areal capacity over 3.0 mAh cm-2 . Pairing zeroVE-Li with a commercial NMC811 or LCO cathode, flexible LMBs that offer a record-breaking figure of merit (FOM, 45.6), large whole-cell energy density (375 Wh L-1 , based on the volume of the anode, separator, cathode, and package), high-capacity retention (> 99.8% per cycle), and remarkable mechanical robustness under practical conditions are demonstrated.

500 Wh kg-1 Class Li Metal Battery Enabled by a Self-Organized Core-Shell Composite Anode.

Lithium (Li) metal offers the highest projected energy density as a battery anode, however its extremely high reactivity induces dendrite growth and dead Li formation during repeated charge/discharge processes, resulting in both poor reversibility and catastrophic failure. Approaches reported to date often seek to suppress dendrites formation at the expense of energy density. Here, a strategy that resolves the above conflict and achieves a dendrite-free and long-term reversible Li metal anode is reported. A self-organized core-shell composite anode, comprising an outer sheath of lithiated liquid metal (Lix LMy ) and an inner layer of Li metal, is developed, which posesses high electrical and ionic conductivity, and physically separates Li from the electrolyte. The introduction of Lix LMy not only prevents dendrite formation, but also eliminates the use of copper as an inert substrate. Full cells made of such composite anodes and commercially available LiNi0.6 Co0.2 Mn0.2 O2 (NCM622 ) cathodes deliver ultrahigh energy density of 1500 Wh L-1 and 483 Wh kg-1 . The high capacity can be maintained for more than 500 cycles, with fading rate of less than 0.05% per cycle. Pairing with LiNi0.8 Co0.1 Mn0.1 O2 (NCM811 ) further raises the energy density to 1732 Wh L-1 and 514 Wh kg-1 .

Lithiophilic Zn Sites in Porous CuZn Alloy Induced Uniform Li Nucleation and Dendrite-free Li Metal Deposition.

Three-dimensional (3D) lithiophilic host is one of the most effective ways to regulate the Li dendrites and volume change in working Li metal anode. The state-of-the-art 3D lithiophilic hosts are facing one main challenge in that the lithiophilic layer would melt or fall off in high-temperature environment when using the thermal infusion method. Herein, a 3D porous CuZn alloy host containing anchored lithiophilic Zn sites is employed to prestore Li using the thermal infusion strategy, and a 3D composite Li is thus fabricated. Benefiting from the lithiophilic Zn sites with a strong adsorption capacity with Li, which is based on the analyses of the nucleation overpotential, binding energy calculation, and the operando optical observation of Li plating/stripping behaviors, facile uniform Li nucleation and dendrite-free Li deposition could be achieved in the interior of the 3D porous CuZn alloy host and the 3D composite Li shows remarkable enhancement in electrochemical performance.