RESUMO
This study aims to improve the mechanical properties of post-consumer recycled (PCR) plastic composed primarily of polypropylene (PP) and polyethylene (PE), which generally exhibit poor miscibility, by applying coupling agents and graphene. Here, we compare a commercially available coupling agent with a directly synthesized maleic anhydride (MA) coupling agent. When applied to a 5:5 blend of recycled PP and PE, an optimum tensile strength was achieved at a 3 wt% coupling agent concentration, with the MA coupling agent outperforming the commercial one. Characterization through Fourier transform infrared spectroscopy (FT-IR) and thermogravimetry analysis (TGA) revealed a PP:PE ratio of approximately 3:7 in the PCR plastics, with 4.86% heterogeneous materials present. Applying 3 wt% of the commercial and MA coupling agents to the PCR plastics resulted in a significant 53.9% increase in the tensile strength, reaching 11.25 MPa, and a remarkable 421.54% increase in the melt flow index (MFI), reaching 25.66 g/10 min. Furthermore, incorporating 5 wt% graphene led to a notable 64.84% increase in the tensile strength. In addition, the application of MA coupling agents and graphene improved the thermal stability of the PCR plastics. These findings show significant promise for addressing environmental concerns associated with plastic waste by facilitating the recycling of PCR plastics into new products. The utilization of coupling agents and graphene offers a viable approach to enhance the mechanical properties of PCR plastics, paving the way for sustainable and environmentally friendly solutions.
RESUMO
As environmental regulations become stricter, weight- and cost-effective fiber-reinforced polymer composites are being considered as alternative materials in the automobile industry. Rapidly impregnating resin into the reinforcing fibers is critical during liquid composite molding, and the optimization of resin impregnation is related to the cycle time and quality of the products. In this review, various resins capable of rapid impregnation, including thermoset and thermoplastic resins, are discussed for manufacturing fiber-reinforced composites used in the automobile industry, along with their advantages and disadvantages. Finally, vital factors and perspectives for developing rapidly impregnated resin-based fiber-reinforced composites for automobile applications are discussed.
RESUMO
Continuous industrial development has increased the demand of energy. Inevitably, the development of energy sources is steadily progressing using various methods. Rather than establishing a new energy source, a system for storing waste heat generated by industry has now been accepted as a useful strategy. Among such systems, the hydration and dehydration reactions of MgO/Mg(OH)2 are eco-friendly, have relatively low toxicity and risk, and have a large reserves. Therefore, it is a promising candidate for a heat-storage system. In this study, ultrahigh-porosity particles are used to maximize the heat-storage efficiency of pure MgO. Due to its large surface area, the heat storage rate is 90.3% of the theoretical value and the reaction rate is very high. In addition, as structural collapse, likely to be caused by volume changes between reactions, is blocked as the porous region is filled and emptied, the cycle stability is secured. Ultrahigh-porosity MgO microparticles can be used to build eco-friendly heat-storage systems.
RESUMO
The potential use of gelatin materials in the liquid composite molding manufacturing (LCM) process was investigated, with specific focus on the reinforcement deformation phenomenon. The adoptability of gelatin as a binder in a composite material with glass fiber for application in the LCM process was evaluated by analyzing the permeability and microscopic structure of the gelatin-coated glass fiber. To assess the tow deformation, the permeability of the non-crimped unidirectional glass fiber mat was evaluated at different flow rates that could be applied in the LCM process. Hysteresis of the permeability was observed as the flow rate increased and decreased, indicative of tow deformation. The permeability of the gelatin-treated glass fiber mat exhibited a relatively smaller variation than that of the untreated glass fiber at the same flow rate. Tow deformation in the untreated and gelatin-treated non-crimped glass fiber mats at different flow rates was evaluated by microscopic analysis and quantified using the tow thickness index. Relatively smaller variations in the permeability and minimal changes in the tow thickness of the gelatin-treated glass fiber mat were observed via microscopic analysis, indicating that gelatin effectively maintained the binding structure of the glass fiber mat.
Assuntos
Gelatina , Vidro , Gelatina/química , Vidro/química , Resinas Vegetais , Resinas Compostas/química , Teste de MateriaisRESUMO
Graphene oxide (GO) and multiwalled carbon nanotubes with silver particles (MWNT-Ag) of different concentrations were used as nanofillers to prepare poly(lactic acid) (PLA) nanoparticle films through the solvent casting method. In this study, the effects of nanoparticles on the crystallization behavior, relationships between the dispersion and electrical properties, and hydrolytic degradation behaviors were investigated for the PLA/MWNT-Ag and PLA/rGO films. Differential scanning calorimetry was used to evaluate the crystallization behaviors of the PLA/MWNT-Ag and PLA/reduced GO (rGO) films. Electron probe microanalysis was performed to characterize the dispersion of MWNT-Ag, and X-ray diffraction and Raman spectroscopy were used to determine the degree of dispersion of rGO in the PLA matrix. The results showed that nanoparticles enhanced the crystallization kinetics of PLA as well as the hydrolytic degradation rate. From the measurement of electrical properties, the electrical conductivity of PLA/MWNT-Ag 1.0 wt% was much higher than that of the pure PLA and PLA/rGO films, showing that MANT and Ag nanoparticles contribute greatly to enhancing the electrical conductivity of the PLA/MWNT-Ag films.
RESUMO
Shape memory polymers (SMPs) are attracting attention for their use in wearable displays and biomedical materials due to their good biocompatibility and excellent moldability. SMPs also have the advantage of being lightweight with excellent shape recovery due to their low density. However, they have not yet been applied to a wide range of engineering fields because of their inferior physical properties as compared to those of shape memory alloys (SMAs). In this study, we attempt to find optimized shape memory polymer composites. We also investigate the shape memory performance and physical properties according to the filler type and amount of hardener. The shape memory composite was manufactured by adding nanocarbon materials of graphite and non-carbon additives of Cu. The shape-recovery mechanism was compared, according to the type and content of the filler. The shape fixation and recovery properties were analyzed, and the physical properties of the shape recovery composite were obtained through mechanical strength, thermal conductivity and differential scanning calorimetry analysis.