Optimization of Glutathione Adhesion Process to Modified Graphene Surfaces.

The presented work shows the results of the functionalization of the graphene surface obtained by the growth on the liquid bimetallic matrices method. We used glutathione (GSH) as a peptide model, which allowed us to optimize the procedure to obtain high process efficiency. To establish the amount of GSH attached to the graphene surface, the Folina-Ciocalteu method was used, which allows the assessment of the concentration of colored reaction products with peptide bonds without the disadvantages of most methods based on direct colored reaction of peptide bonds. Samples surface morphology, quality of graphene and chemical structure in the subsequent stages of surface modification were tested-for this purpose Raman spectroscopy, scanning electron microscopy (SEM), and Fourier-transform infrared spectroscopy (FTIR) were used.

Impact of Plasma Pre-Treatment on the Tribological Properties of DLC Coatings on PDMS Substrates.

The processes of the deposition of carbon coatings on PDMS (polydimethylsiloxane) substrates using plasma techniques are widely used in a large number of studies, in applications ranging from electronic to biological. That is why the potential improvement of their functional properties, including tribological properties, seems very interesting. This paper presents an analysis of the impact of plasma pre-treatment on the properties of the produced diamond-like carbon (DLC) coatings, including changes in the coefficients of friction and wear rates. The initial modification processes were performed using two different techniques based on low-pressure plasma (RF PACVD, radio-frequency plasma-assisted chemical vapour deposition) and dielectric barrier discharge (DBD) plasma. The effects of the above-mentioned treatments on the geometric structure of the PDMS surface and its water contact angles and stability over time were determined. The basic properties of the DLC coatings produced on unmodified substrates were compared to those of the coatings subjected to plasma pre-treatment. The most interesting effects in terms of tribological properties were achieved after the DBD process and production of DLC coatings, achieving a decrease in wear rates to 2.45 × 10-8 mm3/Nm. The tests demonstrate that the cross-linking of the polymer substrate occurs during plasma pre-treatment.

Influence of the Interactions at the Graphene-Substrate Boundary on Graphene Sensitivity to UV Irradiation.

Graphene is a very promising material for electronics applications. In recent years, its sensitivity to ultraviolet (UV) irradiation has been studied extensively. However, there is no clear answer to the question, which factor has a key influence on the sensitivity of graphene to UV. In order to check the influence of the final substrate on the electrical response, graphene transferred on polymeric and non-polymeric substrate was investigated. To achieve this goal three polymeric and three non-polymeric substrates were tested. The results of the preliminary tests indicated the different character of the reaction on UV irradiation in each of group. To explain the reason of the difference, the complementary studies were done. The samples that were resistant to high temperature were annealed in a vacuum at 500 °C to get rid of water trapped between graphene and the substratum. The samples after annealing reacted less dynamically to UV irradiation. Moreover, the progress of changes in electrical response of the annealed samples had a similar character to the polymeric substrates, with the hydrophobic nature of the surface. These studies clearly prove that the sensitivity of graphene to UV irradiation is influenced by water trapped under the graphene.

On the development of a VIPARnd radiotherapy 3D polymer gel dosimeter.

This work presents an improvement of the VIPARnd ('nd' stands for 'normoxic, double', or VIP) polymer gel dosimeter. The gel composition was altered by increasing the concentration of the monomeric components, N-vinylpyrrolidone (NVP) and N,N'-methylenebisacrylamide (MBA), in co-solvent solutions. The optimal composition (VIPARCT, where 'CT' stands for computed tomography, or VIC) comprised: 17% NVP, 8% MBA, 12% t-BuOH, 7.5% gelatine, 0.007% ascorbic acid, 0.0008% CuSO4 × 5H2O and 0.02% hydroquinone. The following characteristics of VIC were achieved: (i) linear dose range of 0.9_30 Gy, (ii) saturation for radiation doses of over 50 Gy, (iii) threshold dose of about 0.5 Gy, (iv) dose sensitivity of 0.171 Gy-1 s-1, which is roughly 2.2 times higher than that of VIP (for nuclear magnetic resonance measurements). It was also found that VIC is dose- rate-independent, and its dose response does not alter if the radiation source is changed from electrons to photons for external beam radiotherapy. The gel responded similarly to irradiation with small changes in radiation energy but was sensitive to larger energy changes. The VIC gel retained temporal stability from 20 h until at least 10 d after irradiation, whereas spatial stability was retained from 20 h until at least 6 d after irradiation. The scheme adopted for VIC manufacturing yields repeatable gels in terms of radiation dose response. The VIC was also shown to perform better than VIP using x-ray computed tomography as a readout method; the dose sensitivity of VIC (0.397 HU Gy-1) was 1.5 times higher than that of VIP. Also, the dose resolution of VIC was better than that of VIP in the whole dose range examined.