Mid-temperature CO2 Adsorption over Different Alkaline Sorbents Dispersed over Mesoporous Al2O3.

CO2 adsorbents comprising various alkaline sorption active phases supported on mesoporous Al2O3 were prepared. The materials were tested regarding their CO2 adsorption behavior in the mid-temperature range, i.e., around 300 °C, as well as characterized via XRD, N2 physisorption, CO2-TPD and TEM. It was found that the Na2O sorption active phase supported on Al2O3 (originated following NaNO3 impregnation) led to the highest CO2 adsorption capacity due to the presence of CO2-philic interfacial Al-O--Na+ sites, and the optimum active phase load was shown to be 12 wt % (0.22 Na/Al molar ratio). Additional adsorbents were prepared by dispersing Na2O over different metal oxide supports (ZrO2, TiO2, CeO2 and SiO2), showing an inferior performance than that of Na2O/Al2O3. The kinetics and thermodynamics of CO2 adsorption were also investigated at various temperatures, showing that CO2 adsorption over the best-performing Na2O/Al2O3 material is exothermic and follows the Avrami model, while tests under varying CO2 partial pressures revealed that the Langmuir isotherm best fits the adsorption data. Lastly, Na2O/Al2O3 was tested under multiple CO2 adsorption-desorption cycles at 300 and 500 °C, respectively. The material was found to maintain its CO2 adsorption capacity with no detrimental effects on its nanostructure, porosity and surface basic sites, thereby rendering it suitable as a reversible CO2 chemisorbent or as a support for the preparation of dual-function materials.

Synthesis, characterization, and preliminary insights of ZnFe2O4 nanoparticles into potential applications, with a focus on gas sensing.

This work presents a hydrothermal-based facile method for synthesizing ZnFe2O4, whose size can be controlled with the concentration of sodium acetate used as a fuel and its physical changes at nanoscales when exposed to two different gases. The structural, morphological, compositional, and electronic properties of the synthesized samples are also presented in this paper. The crystal structure of the synthesized samples was determined using an X-ray Diffractometer (XRD). The results revealed fluctuations in the size, lattice parameter, and strain in the nanoparticles with increasing the concentration of sodium acetate. Field-Emission Scanning Electron Microscopy (FESEM) was used to determine synthesized materials' morphology and particle size. It revealed that the particles possessed approximately spherical morphology whose size decreased significantly with the increasing amount of sodium acetate. Transmission Electron Microscopy (TEM) was utilized to determine the structure, morphology, and elemental distributions in particles at the nanoscale, and it confirmed the findings of XRD and FESEM analyses. The high-resolution TEM (HRTEM) imaging analysis of the nanoparticles in our studied samples revealed that the particles predominantly possessed (001) type facets. X-ray photoelectron spectroscopy (XPS) and core-loss electron energy loss spectroscopy (EELS) showed an increasing fraction of Fe2+ with the decreasing size of the particles in samples. The Brunauer, Emmett, and Tellers (BET) analysis of samples revealed a higher surface area as the particle size decreases. In addition, the determined surface area and pore size values are compared with the literature, and it was found that the synthesized materials are promising for gas-sensing applications. The ab initio calculations of the Density of States (DOS) and Band structure of (001) surface terminating ZnFe2O4 were carried out using Quantum Espresso software to determine the bandgap of the synthesized samples. They were compared to their corresponding experimentally determined bandgap values and showed close agreement. Finally, in-situ TEM measurement was carried out on one of the four studied samples with robust properties using Ar and CO2 as reference and target gases, respectively. It is concluded from the presented study that the size reduction of the ZnFe2O4 nanoparticles (NPs) tunes the bandgap and provides more active sites due to a higher concentration of oxygen vacancies. The in-situ TEM showed us a nanoscale observation of the change in one of the crystal structure parameters. The d spacing of ZnFe2O4 NPs showed a noticeable fluctuation, reaching more than 5% upon exposure to CO2 and Ar gases.

Carbon dioxide adsorbents from flame-made diesel soot nanoparticles.

Carbon dioxide (CO2) is the top contributor to global warming. On the other, soot particles formed during fuel combustion and released into the atmosphere are harmful and also contribute to global warming. It would therefore be highly advantageous to capture soot and make use of it as a feedstock to synthesize carbon-based materials for applications such as carbon dioxide adsorption. In this work, flame-made diesel soot nanoparticles were used to produce a variety of activated carbons by combined oxidative treatment with hydrogen peroxide (H2O2) and potassium hydroxide (KOH), and their performance towards CO2 adsorption was evaluated. The effect of the chemical activation of soot with H2O2 for different reaction times and with KOH on the physicochemical properties of the activated carbons was investigated and compared to fresh soot. Interestingly, hollow aggregates of carbonaceous nanoparticles of a high interplanar distance, reduced polycyclic aromatic hydrocarbons (PAH) size, shorter PAH stacks, mesoporous structure, and a high content of oxygen functionalities along with other structural defects in PAHs were obtained in the synthesized activated carbons. Among the various analysis techniques employed, Raman spectroscopy indicated that the ID/IG ratio in soot decreased after simultaneous chemical treatment, though it did not indicate any enhancement in the graphitic character since the carbonyl and carboxylic containing PAHs and monovacancies (which cause defects in PAHs) also contribute to the increase in the intensity of the graphitic band. The activated carbons possessed promising CO2 adsorption capacities, adsorption kinetics and CO2/N2 selectivity. For example, one of the activated carbons, following H2O2 treatment for 9 h and a subsequent KOH activation, exhibited a CO2 adsorption capacity of 1.78 mmol/g at 1 bar and 25 °C, representing an increase of 161 % in capacity as compared to fresh soot. Hollow aggregates of carbonaceous nanoparticles consisting of shorter PAHs with a larger number of defects led to enhanced CO2 adsorption rate and CO2/N2 selectivity on activated carbons.

Low-Temperature Synthesis of Magnetic Carbonaceous Materials Coated with Nanosilica for Rapid Adsorption of Methylene Blue.

This work reports the synthesis of nanosilica-coated magnetic carbonaceous adsorbents (MCA@SiO2) using low-temperature hydrothermal carbonization technique (HCT) and the feasibility to utilize it for methylene blue (MB) adsorption. Initially, a carbon precursor (CP) was synthesized from corn starch under saline conditions at 453 K via HCT followed by the magnetization of CP again via HCT at 453 K. Subsequently, MCA was coated with silica nanoparticles. MCA and MCA@SiO2 were characterized using X-ray diffraction, Fourier transform infrared, scanning electron microscopy/energy-dispersive spectroscopy, transmission electron microscopy, and Brunauer-Emmett-Teller (BET) N2 adsorption-desorption isotherms. The BET surface area of MCA and MCA@SiO2 were found to be 118 and 276 m2 g-1, respectively. Adsorption of MB onto MCA@SiO2 was performed using batch adsorption studies and in the optimum condition, MCA@SiO2 showed 99% adsorption efficiency with 0.5 g L-1 of MCA@SiO2 at pH 7. Adsorption isotherm studies predicted that MB adsorption onto MCA@SiO2 was homogeneous monolayer adsorption, which was best described using a Langmuir model with the maximum adsorption capacity of 516.9 mg g-1 at 25 °C. During adsorption kinetics, a rapid dye removal was observed which followed pseudo-first- as well as pseudo-second-order models, which suggested that MB dye molecules were adsorbed onto MCA@SiO2 via both ion exchange as well as the chemisorption process. The endothermic and spontaneous nature of the adsorption of MB onto MCA@SiO2 was established by thermodynamics studies. Mechanism of dye diffusion was collectively governed by intraparticle diffusion and film diffusion processes. Furthermore, MB was also selectively adsorbed from its mixture with an anionic dye, that is, methyl orange. Column adsorption studies showed that approximately 500 mL of MB having 50 mg L-1 concentration can be treated with 0.5 g L-1 of MCA@SiO2. Furthermore, MCA@SiO2 was repeatedly used for 20 cycles of adsorption-desorption of MB. Therefore, MCA@SiO2 can be effectively utilized in cationic dye-contaminated wastewater remediation applications.

Palladium supported on chitosan as a recyclable and selective catalyst for the synthesis of 2-phenyl ethanol.

Two different chitosan supported palladium based catalysts were prepared, wherein dispersed palladium nanoparticles were obtained via chemical reduction supported on chitosan (Pd/CTS) and amine functionalized modified chitosan (Pd/AFCTS). The catalytic activity of the Pd-based catalysts, Pd/CTS and Pd/AFCTS, were assessed in the hydrogenation of styrene oxide to 2-phenyl ethanol. Both Pd-based catalysts enhanced the formation of the desired 2-phenyl ethanol in contrast to a conventional Pd/C catalyst without the assistance of inorganic or organic base. A considerable influence on the conversion and selectivity was observed in the case of Pd/AFCTS, consisting of palladium nanoparticles stabilized and dispersed on amine-functionalized chitosan matrix, affording complete conversion of styrene oxide with 98% selectivity to 2-phenyl ethanol. The catalyst Pd/AFCTS has also been recycled without significant loss of activity and selectivity.