Microplastic polymer properties as deterministic factors driving terrestrial plastisphere microbiome assembly and succession in the field.

Environmental microplastic (MP) is ubiquitous in aquatic and terrestrial ecosystems providing artificial habitats for microbes. Mechanisms of MP colonization, MP polymer impacts, and effects on soil microbiomes are largely unknown in terrestrial systems. Therefore, we experimentally tested the hypothesis that MP polymer type is an important deterministic factor affecting MP community assembly by incubating common MP polymer types in situ in landfill soil for 14 months. 16S rRNA gene amplicon sequencing indicated that MP polymers have specific impacts on plastisphere microbiomes, which are subsets of the soil microbiome. Chloroflexota, Gammaproteobacteria, certain Nitrososphaerota, and Nanoarchaeota explained differences among MP polymers and time points. Plastisphere microbial community composition derived from different MP diverged over time and was enriched in potential pathogens. PICRUSt predictions of pathway abundances and quantitative PCR of functional marker genes indicated that MP polymers exerted an ambivalent effect on genetic potentials of biogeochemical cycles. Overall, the data indicate that (i) polymer type as deterministic factor rather than stochastic factors drives plastisphere community assembly, (ii) MP impacts greenhouse gas metabolism, xenobiotic degradation and pathogen distribution, and (iii) MP serves as an ideal model system for studying fundamental questions in microbial ecology such as community assembly mechanisms in terrestrial environments.

Influence of Carbon Nanotube-Pretreatment on the Properties of Polydimethylsiloxane/Carbon Nanotube-Nanocomposites.

Incorporating nanofillers into elastomers leads to composites with an enormous potential regarding their properties. Unfortunately, nanofillers tend to form agglomerates inhibiting adequate filler dispersion. Therefore, different carbon nanotube (CNT) pretreatment methods were analyzed in this study to enhance the filler dispersion in polydimethylsiloxane (PDMS)/CNT-composites. By pre-dispersing CNTs in solvents an increase in electrical conductivity could be observed within the sequence of tetrahydrofuran (THF) > acetone > chloroform. Optimization of the pre-dispersion step results in an AC conductivity of 3.2 × 10-4 S/cm at 1 Hz and 0.5 wt.% of CNTs and the electrical percolation threshold is decreased to 0.1 wt.% of CNTs. Optimum parameters imply the use of an ultrasonic finger for 60 min in THF. However, solvent residues cause a softening effect deteriorating the mechanical performance of these composites. Concerning the pretreatment of CNTs by physical functionalization, the use of surfactants (sodium dodecylbenzenesulfonate (SDBS) and polyoxyethylene lauryl ether ("Brij35")) leads to no improvement, neither in electrical conductivity nor in mechanical properties. Chemical functionalization enhances the compatibility of PDMS and CNT but damages the carbon nanotubes due to the oxidation process so that the improvement in conductivity and reinforcement is superimposed by the CNT damage even for mild oxidation conditions.

Polycyclic aromatic hydrocarbons in consumer goods made from recycled rubber material: A review.

Vast amounts of rubber waste are produced every year, where end-of-life tires (ELT) mount up the largest share with several million tonnes in the EU each year. This points up the necessity for reusing end-of-life rubber material. The recycled material shows nearly the same advantages like the origin materials. In consequence, the recycled material is predestined for the use in sport facilities, which explains that around half of the recycled ELTs are used to produce artificial turf, sports flooring and injury-prevention pavements on playgrounds. Since tires contain potentially toxic components, there is worry concerning the release of such chemical substances stemming from these products. As tires contain highly aromatic oils and carbon black, the presence of polycyclic aromatic hydrocarbons (PAH) and their carcinogenic properties are discussed controversially. This review issues a comprehensive overview of PAH release and a conclusive assessment on human health risk. Analytical studies dealing with the PAH content of consumer goods made from recycled rubber material and associated risk assessments are reviewed. In conclusion PAHs can be detected in consumer goods made from recycled rubber and are released into the environment. They reach humans via leaching (soil, ground water, rivers), oral intake, dermal exposure and inhalation. Thereby, dermal contact or inhalation is the primary route of exposure, whereas oral intake and environmental pollution are regarded as secondary risks. The amount of PAHs that could potentially harm humans is in the magnitude of urban pollution. Risk assessment studies reviewed in this article show no serious risk potential.

Fully defined in situ cross-linkable alginate and hyaluronic acid hydrogels for myocardial tissue engineering.

Despite recent major advances including reprogramming and directed cardiac differentiation of human cells, therapeutic application of in vitro engineered myocardial tissue is still not feasible due to the inability to construct functional large vascularized contractile tissue patches based on clinically applicable and fully defined matrix components. Typical matrices with preformed porous 3D structure cannot be applied due to the obvious lack of migratory capacity of cardiomyocytes (CM). We have therefore developed a fully defined in situ hydrogelation system based on alginate (Alg) and hyaluronic acid (HyA), in which their aldehyde and hydrazide-derivatives enable covalent hydrazone cross-linking of polysaccharides in the presence of viable myocytes. By varying degrees of derivatization, concentrations and composition of blends in a modular system, mechanophysical properties of the resulting hydrogels are easily adjustable. The hydrogel allowed for the generation of contractile bioartificial cardiac tissue from CM-enriched neonatal rat heart cells, which resembles native myocardium. A combination of HyA and highly purified human collagen I led to significantly increased active contraction force compared to collagen, only. Therefore, our in situ cross-linking hydrogels represent a valuable toolbox for the fine-tuning of engineered cardiac tissue's mechanical properties and improved functionality, facilitating clinical translation toward therapeutic heart muscle reconstruction.