Understanding the Correlation between Electrochemical Performance and Operating Mechanism of a Co-free Layered-Spinel Composite Cathode for Na-Ion Batteries.

Compositing different crystal structures of layered transition metal oxides (LTMOs) is an emerging strategy to improve the electrochemical performance of LTMOs in sodium-ion batteries. Herein, a cobalt-free P2/P3-layered spinel composite, P2/P3-LS-Na1/2Mn2/3Ni1/6Fe1/6O2 (LS-NMNF), is synthesized, and the synergistic effects from the P2/P3 and spinel phases were investigated. The material delivers an initial discharge capacity of 143 mAh g-1 in the voltage range of 1.5-4.0 V and displays a capacity retention of 73% at the 50th cycle. The material shows a discharge capacity of 72 mAh g-1 at 5C. This superior rate performance by the material could be by virtue of the increased electronic conductivity contribution of the incorporated spinel phase. The charge compensation mechanism of the material is investigated by in operando X-ray absorption spectroscopy (in a voltage range of 1.5-4.5 V vs Na+/Na), which revealed the contribution of all transition metals toward the generated capacity. The crystal structure evolution of each phase during electrochemical cycling was analyzed by in operando X-ray diffraction. Unlike in the case of many reported P2/P3 composite cathode materials and spinel-incorporated cobalt-containing P2/P3 composites, the formation of a P'2 phase at the end of discharge is absent here.

Formation of Stable Radicals by Mechanochemistry and Their Application for Magic Angle Spinning Dynamic Nuclear Polarization Solid-State NMR Spectroscopy.

High-field magic angle spinning (MAS) dynamic nuclear polarization (DNP) is becoming a common technique for improving the sensitivity of solid-state nuclear magnetic resonance (SSNMR) by the hyperpolarization of nuclear spins. Recently, we have shown that gamma irradiation is capable of creating long-lived free radicals that are amenable to MAS DNP in quartz and a variety of organic solids. Here, we demonstrate that ball milling is able to generate millimolar concentrations of stable radical species in diverse materials such as polystyrene, cellulose, borosilicate glass, and fused quartz. High-field electron paramagnetic resonance (EPR) was used to obtain further insight into the nature of the radicals formed in ball milled quartz and borosilicate glass. We further show that radicals generated in quartz by ball milling can be used for solid-effect DNP. We obtained 29Si DNP enhancements of approximately 114 and 33 at 110 K and room temperature, respectively, from a sample of ball milled quartz.

Systematic Study of the Multiple Variables Involved in V2AlC Acid-Based Etching Processes, a Key Step in MXene Synthesis.

The realization of the broad range of application of MXenes relies on the successful and reproducible synthesis of quality materials of tailored properties. To date, most MXenes have been produced making use of acid-based etching methods, yet an in-depth understanding of etching processes is lacking. Herein, we have engaged in a comprehensive study of the multiple variables involved in the synthesis of V2CTx with focus on the properties of etched materials. Two main sets of experiments were considered, each using a different V2AlC precursor and a range of synthesis variables including reaction time and temperature, mixing rate, and type of acid. Correlations of synthesis conditions-materials properties were investigated using a broad range of characterization techniques including analytical methods, scanning and transmission electron microscopy, X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Findings indicated the crucial relevance of properties of the MAX precursor such as elemental composition, particle size, and crystal structure on etching processes and properties of etched materials. Particularly, depending on the MAX precursor, two etching patterns were identified, core-shell and plate-by-plate, the latter describing a more efficient etching. Combined studies of elemental composition, crystal structure, and yield quantification allowed us to evaluate the effectiveness of etching processes. XRD studies revealed key crystal-structure-type of acid correlations showing advantages of using a HF/HCl mix over only HF. Analytical methods XRD and XPS delivered insights into undergoing chemical processes and their influence on bulk and surface chemistry of etched materials. The relevance for reaction kinetics of highly correlated variables such as reaction vessel dimensions, mixing efficiency, and reaction temperature was recognized. For the first time, a MXene synthesis has been investigated comprehensively highlighting its multivariable nature and the high variable intercorrelation, opening up venues for further investigation on MAX and MXene synthesis.

Universal and efficient extraction of lithium for lithium-ion battery recycling using mechanochemistry.

The increasing lithium-ion battery production calls for profitable and ecologically benign technologies for their recycling. Unfortunately, all used recycling technologies are always associated with large energy consumption and utilization of corrosive reagents, which creates a risk to the environment. Herein we report a highly efficient mechanochemically induced acid-free process for recycling Li from cathode materials of different chemistries such as LiCoO2, LiMn2O4, Li(CoNiMn)O2, and LiFePO4. The introduced technology uses Al as a reducing agent in the mechanochemical reaction. Two different processes have been developed to regenerate lithium and transform it into pure Li2CO3. The mechanisms of mechanochemical transformation, aqueous leaching, and lithium purification were investigated. The presented technology achieves a recovery rate for Li of up to 70% without applying any corrosive leachates or utilizing high temperatures. The key innovation is that the regeneration of lithium was successfully performed for all relevant cathode chemistries, including their mixture.

Long-Range Cationic Disordering Induces two Distinct Degradation Pathways in Co-Free Ni-Rich Layered Cathodes.

Ni-rich layered oxides are one of the most attractive cathode materials in high-energy-density lithium-ion batteries, their degradation mechanisms are still not completely elucidated. Herein, we report a strong dependence of degradation pathways on the long-range cationic disordering of Co-free Ni-rich Li1-m (Ni0.94 Al0.06 )1+m O2 (NA). Interestingly, a disordered layered phase with lattice mismatch can be easily formed in the near-surface region of NA particles with very low cation disorder (NA-LCD, m≤0.06) over electrochemical cycling, while the layered structure is basically maintained in the core of particles forming a "core-shell" structure. Such surface reconstruction triggers a rapid capacity decay during the first 100 cycles between 2.7 and 4.3 V at 1 C or 3 C. On the contrary, the local lattice distortions are gradually accumulated throughout the whole NA particles with higher degrees of cation disorder (NA-HCD, 0.06≤m≤0.15) that lead to a slow capacity decay upon cycling.

Incommensurate transition-metal dichalcogenides via mechanochemical reshuffling of binary precursors.

A new family of heterostructured transition-metal dichalcogenides (TMDCs) with incommensurate ("misfit") spatial arrangements of well-defined layers was prepared from structurally dissimilar single-phase 2H-MoS2 and 1T-HfS2 materials. The experimentally observed heterostructuring is energetically favorable over the formation of homogeneous multi-principle element dichalcogenides observed in related dichalcogenide systems of Mo, W, and Ta. The resulting three-dimensional (3D) heterostructures show semiconducting behavior with an indirect band gap around 1 eV, agreeing with values predicted from density functional theory. Results of this joint experimental and theoretical study open new avenues for generating unexplored metal-dichalcogenide heteroassemblies with incommensurate structures and tunable physical properties.

Unprecedented generation of 3D heterostructures by mechanochemical disassembly and re-ordering of incommensurate metal chalcogenides.

Three-dimensional heterostructures are usually created either by assembling two-dimensional building blocks into hierarchical architectures or using stepwise chemical processes that sequentially deposit individual monolayers. Both approaches suffer from a number of issues, including lack of suitable precursors, limited reproducibility, and poor scalability of the preparation protocols. Therefore, development of alternative methods that enable preparation of heterostructured materials is desired. We create heterostructures with incommensurate arrangements of well-defined building blocks using a synthetic approach that comprises mechanical disassembly and simultaneous reordering of layered transition-metal dichalcogenides, MX2, and non-layered monochalcogenides, REX, where M = Ta, Nb, RE = Sm, La, and X = S, Se. We show that the discovered solid-state processes are rooted in stochastic mechanochemical transformations directed by electronic interaction between chemically and structurally dissimilar solids toward atomic-scale ordering, and offer an alternative to conventional heterostructuring. Details of composition-structure-properties relationships in the studied materials are also highlighted.

Multi-principal element transition metal dichalcogenides via reactive fusion of 3D-heterostructures.

Transition metal dichalcogenides combining multiple principal elements in their structures are synthesized via mechanochemical exfoliation and spontaneous reassembly of binary precursors into 3D-heterostructures that are converted into single-phase layered materials by high-temperature reactive fusion. Physical and chemical events enabling these transformations are summarized in the form of a conceivable reaction mechanism.

Improved Voltage and Cycling for Li+ Intercalation in High-Capacity Disordered Oxyfluoride Cathodes.

New high-capacity intercalation cathodes of Li2V x Cr1-x O2F with a stable disordered rock salt host framework allow a high operating voltage up to 3.5 V, good rate performance (960 Wh kg-1 at ≈1 C), and cycling stability.

P3-Type Layered Sodium-Deficient Nickel-Manganese Oxides: A Flexible Structural Matrix for Reversible Sodium and Lithium Intercalation.

Sodium-deficient nickel-manganese oxides exhibit a layered structure, which is flexible enough to acquire different layer stacking. The effect of layer stacking on the intercalation properties of P3-Nax Ni0.5 Mn0.5 O2 (x=0.50, 0.67) and P2-Na2/3 Ni1/3 Mn2/3 O2 , for use as cathodes in sodium- and lithium-ion batteries, is examined. For P3-Na0.67 Ni0.5 Mn0.5 O2 , a large trigonal superstructure with 2√3 a×2√3 a×2 c is observed, whereas for P2-Na2/3 Ni1/3 Mn2/3 O2 there is a superstructure with reduced lattice parameters. In sodium cells, P3 and P2 phases intercalate sodium reversibly at a well-expressed voltage plateau. Preservation of the P3-type structure during sodium intercalation determines improving cycling stability of the P3 phase within an extended potential range, in comparison with that for the P2 phase, for which a P2-O2 phase transformation has been found. Between 2.0 and 4.0 V, P3 and P2 phases display an excellent rate capability. In lithium cells, the P3 phase intercalates lithium, accompanied by a P3-O3 structural transformation. The in situ generated O3 phase, containing lithium and sodium simultaneously, determines the specific voltage profile of P3-Nax Ni0.5 Mn0.5 O2 . The P2 phase does not display any reversible lithium intercalation. The P3 phase demonstrates a higher capacity at lower rates in lithium cells, whereas in sodium cells P3-Nax Ni0.5 Mn0.5 O2 operates better at higher rates. These findings reveal the unique ability of sodium-deficient nickel-manganese oxides with a P3-type structure for application as low-cost electrode materials in both sodium- and lithium-ion batteries.