Tuning viscoelasticity and stiffness in bioprinted hydrogels for enhanced 3D cell culture: A multi-scale mechanical analysis.

Bioprinted hydrogels are extensively studied to provide an artificial matrix for 3D cell culture. The success of bioprinting hydrogels relies on fine-tuning their rheology and composition to achieve shear-thinning behavior. However, a challenge arises from the limited viscoelastic and stiffness range accessible from a single hydrogel formulation. Nevertheless, hydrogel mechanical properties are recognized as essential cues influencing cell phenotype, migration, and differentiation. Thus, it is crucial to develop a system to easily modulate bioprinted hydrogels' mechanical behaviors. In this work, we modulated the viscoelastic properties and stiffness of bioprinted hydrogels composed of fibrinogen, alginate, and gelatin by tuning the crosslinking bath solution. Various concentrations of calcium ionically crosslinked alginate, while transglutaminase crosslinked gelatin. Subsequently, we characterized the mechanical behavior of our bioprinted hydrogels from the nanoscale to the macroscale. This approach enabled the production of diverse bioprinted constructs, either with similar elastic behavior but different elastic moduli or with similar elastic moduli but different viscoelastic behavior from the same hydrogel formulation. Culturing fibroblasts in the hydrogels for 33 days revealed a preference for cell growth and matrix secretion in the viscoelastic hydrogels. This work demonstrates the suitability of the method to decouple the effects of material mechanical from biochemical composition cues on 3D cultured cells.

Crystal and molecular structure of V-amylose complexed with ibuprofen.

Rectangular V-amylose single crystals were prepared by adding racemic ibuprofen to hot dilute aqueous solutions of native and enzymatically-synthesized amylose. The lamellar thickness increased with increasing degree of polymerization of amylose and reached a plateau at about 7 nm, consistent with a chain-folding mechanism. The CP/MAS NMR spectrum as well as base-plane electron and powder X-ray diffraction patterns recorded from hydrated specimens were similar to those of V-amylose complexed with propan-2-ol. Amylose was crystallized in an orthorhombic unit cell with parameters a = 2.824 ± 0.001 nm, b = 2.966 ± 0.001 nm, and c = 0.800 ± 0.001 nm. A molecular model was proposed based on structural analogies with the Vpropan-2-ol complex and on assumptions on the stoichiometry of ibuprofen. The unit cell would contain four antiparallel 7-fold amylose single helices with ibuprofen molecules distributed inside and between the helices.

Interfacial rheological properties of self-assembling biopolymer microcapsules.

Tuning the mechanical properties of microcapsules through a cost-efficient route of fabrication is still a challenge. The traditional method of layer-by-layer assembly of microcapsules allows building a tailored composite multi-layer membrane but is technically complex as it requires numerous steps. The objective of this article is to characterize the interfacial rheological properties of self-assembling biopolymer microcapsules that were obtained in one single facile step. This thorough study provides new insights into the mechanics of these weakly cohesive membranes. Firstly, suspensions of water-in-oil microcapsules were formed in microfluidic junctions by self-assembly of two oppositely charged polyelectrolytes, namely chitosan (water soluble) and phosphatidic fatty acid (oil soluble). In this way, composite membranes of tunable thickness (between 40 and 900 nm measured by AFM) were formed at water/oil interfaces in a single step by changing the composition. Secondly, microcapsules were mechanically characterized by stretching them up to break-up in an extensional flow chamber which extends the relevance and convenience of the hydrodynamic method to weakly cohesive membranes. Finally, we show that the design of microcapsules can be 'engineered' in an extensive way since they present a wealth of interfacial rheological properties in terms of elasticity, plasticity and yield stress whose magnitudes can be controlled by the composition. These behaviors are explained by the variation of the membrane thickness with the physico-chemical parameters of the process.

Structural Variations in Hybrid All-Nanoparticle Gibbsite Nanoplatelet/Cellulose Nanocrystal Multilayered Films.

Cellulose nanocrystals (CNCs) are promising biosourced building blocks for the production of high performance materials. In the last ten years, CNCs have been used in conjunction with polymers for the design of multilayered thin films via the layer-by-layer assembly technique. Herein, polymer chains have been replaced with positively charged inorganic gibbsite nanoplatelets (GN) to form hybrid "nanoparticle-only" composite films. A combination of atomic force microscopy and neutron reflectivity experiments was exploited to investigate the growth and structure of the films. Data show that the growth and density of GN/CNC films can be tuned over a wide range during preparation by varying the ionic strength in the CNC suspension and the film drying protocol. Specifically, thin and dense multilayered films or very thick, more porous mixed slabs, as well as intermediate internal structures, could be obtained in a predictable manner. The influence of key physicochemical parameters on the multilayer film buildup was elucidated and the film architecture was linked to the dominating interaction forces between the components. The degree of structural control over these hybrid nanoparticle-only films is much higher than that reported for CNC/polymer films, which offers new properties and potential applications as separation membranes or flame retardant coatings.

Preparation and enzymatic hydrolysis of nanoparticles made from single xyloglucan polysaccharide chain.

In this work, polysaccharide nanoparticles based on tamarind seeds xyloglucan are prepared, analyzed in term of characteristic sizes and morphology, and degraded by the action of a glycoside-hydrolase. Obtained in an aqueous NaNO2 solution (0.1M), these unaggregated nanoparticles have a characteristic diameter of ca. 60 nm (DLS, AFM and TEM measures). They are not compact, but highly swollen and look like hyperbranched and dendrimer-like (soft sphere model) structures. This observation is coherent with the native structure of the xyloglucan macromolecules which are themselves branched. The enzymatic hydrolysis by cellulase of Trichoderma reesei of the xyloglucan nanoparticles is investigated. In particular, the apparent mass molecular weight drastically decreases meaning that the xyloglucan nanoparticles are effectively fully hydrolyzed by the endo-ß-(1,4)-glucanase. Furthermore, we observe that the enzyme has to uncoil the nanoparticles before cutting the ß-(1→4) bonds and digesting the xyloglucan.

Probing multivalent host-guest interactions between modified polymer layers by direct force measurement.

The adhesion behavior between modified polysaccharide layers capable of forming host-guest complexes has been determined by direct force measurements with the atomic force microscope (AFM). Polysaccharides bearing either host or guest moieties were obtained by derivatization of chitosan with pendant ß-cyclodextrin (CD) and adamantane (AD) moieties, respectively. These modified polysaccharides were covalently immobilized either to flat surfaces or to AFM-probes. The number of interacting polymer segments has been reduced significantly by covalently immobilizing chitosan to an AFM-tip with small radius and measuring the forces between the protruding polymer segments and a chitosan layer immobilized to a flat surface. By this approach, it was possible to determine the interaction between polymer layers on the level of single polymer strands. To separate contributions to the adhesion due to the formation of host-guest complexes from unspecific interactions, we performed measurements between various combinations of chitosan derivatives. With the same polymer probe of adamantane-modified chitosan, the interaction against a number of different chitosan layers has been determined, including ones that are not able to form host-guest complexes, such as unmodified chitosan or ß-cyclodextrin modified chitosan, which has been blocked previously by addition of adamantane. The resulting adhesion behavior has been analyzed in terms of the total work of adhesion, the number of rupture events, and the corresponding lengths of the polymer segments as well as rupture forces. A clear difference has been found for systems where the formation of host-guest complexes is possible in comparison to the absence of specific multivalent interaction between the polysaccharide layers. In particular, the work of adhesion is increasing up to an order of magnitude upon the formation of host-guest complexes between the chitosan layers.

Designing hyaluronic acid-based layer-by-layer capsules as a carrier for intracellular drug delivery.

Polyelectrolyte microcapsules were prepared by the layer-by-layer assembly of hyaluronic acid (HA) and a polycationic polymer, poly(allylamine) (PAH) or poly(lysine) (PLL). The influence of the polycationic partner on the morphology, stability, permeability properties, and enzymatic degradation of microcapsules was thoroughly analyzed. It was found that these properties could be tuned by shell cross-linking. Confocal microscopy studies of cellular uptake of the capsules showed that the polyelectrolyte shells remain stable outside the cells but readily break open once internalized by cells, suggesting their potential as carrier for intracellular drug delivery.

Structural basis of the affinity for oligomannosides and analogs displayed by BC2L-A, a Burkholderia cenocepacia soluble lectin.

The opportunistic pathogen Burkholderia cenocepacia contains three soluble carbohydrate-binding proteins, related to the fucose-binding lectin PA-IIL from Pseudomonas aeruginosa. All contain a PA-IIL-like domain and two of them have an additional N-terminal domain that displays no sequence similarities with known proteins. Printed arrays screening performed on the shortest one, B. cenocepacia lectin A (BC2L-A), demonstrated the strict specificity for oligomannose-type N-glycan structures (Lameignere E, Malinovská L, Sláviková M, Duchaud E, Mitchell EP, Varrot A, Sedo O, Imberty A, Wimmerová M. 2008. Structural basis for mannose recognition by a lectin from opportunistic bacteria Burkholderia cenocepacia. Biochem J. 411:307-318.). The disaccharides alphaMan1-2Man, alphaMan1-3Man, and alphaMan1-6Man and the trisaccharide alphaMan1-3(alphaMan1-6)Man were tested by titration microcalorimetry in order to evaluate their affinity for BC2L-A in solution and to characterize the thermodynamics of the binding. Oligomannose analogs presenting two mannoside residues separated by either flexible or rigid spacer were also tested. Only the rigid one yields to high affinity binding with a fast kinetics of clustering, while the flexible analog and the trimannoside display moderate affinities and no clustering effect on short time scale. The crystal structures of BC2L-A have been obtained in complex with alphaMan1-3Man disaccharide and alphaMan1(alphaMan1-6)-3Man trisaccharide. The lengthy time required for the co-crystallization with the trisaccharide allowed for the formation of cluster since in the BC2L-A-trimannose complex solved at 1.1 A resolution, the sugar creates a bridge between two adjacent dimers, yielding to molecular strings. AFM experiments were performed in order to visualize the filaments formed in solution by this type of interaction.

Non-electrostatic building of biomimetic cellulose-xyloglucan multilayers.

Layer-by-layer assembly was used to build thin films, consisting of multiple layers alternating cellulose nanocrystals and xyloglucan, benefiting from the strong non-electrostatic cellulose-xyloglucan interaction. Data from atomic force microscopy and neutron reflectivity showed that these well-defined films exhibited a thickness increasing linearly with the number of layers, without increase in surface roughness. These "green" nanocomposite films, reminiscent of plant cell wall, are composed of a regular stack of single layers of cellulose nanocrystals separated by very thin xyloglucan spacers. Such architecture differs from the one formed by cellulose/polycations multilayers, where the cellulose phase itself consists of a double layer.

Structural details of cellulose nanocrystals/polyelectrolytes multilayers probed by neutron reflectivity and AFM.

Neutron reflectivity measurements and AFM observations were used as complementary techniques to investigate multilayered films consisting of alternating sheets of rigid cellulose nanocrystals and flexible poly(allylamine hydrochloride) (PAH) prepared by the layer-by-layer assembly technique. Both techniques showed that smooth films with a high load of cellulose could be obtained. After deposition, the cellulose component occurred as a double layer with different densities: 50% and 25% for the lower and upper layer, respectively. A linear growth of the multilayer and the presence of a Bragg peak on neutron reflectivity curves indicated the formation of a well-ordered structure resulting from entropy-driven assembly and smoothening effect of the flexible PAH macromolecules. The possible alignment of the nanocrystals when anisotropic suspensions were used is also shown and opens the route to an improved control of the architecture of these multilayers.

The shape and size distribution of crystalline nanoparticles prepared by acid hydrolysis of native cellulose.

The shape and size distribution of crystalline nanoparticles resulting from the sulfuric acid hydrolysis of cellulose from cotton, Avicel, and tunicate were investigated using transmission electron microscopy (TEM) and atomic force microscopy (AFM) as well as small- and wide-angle X-ray scattering (SAXS and WAXS). Images of negatively stained and cryo-TEM specimens showed that the majority of cellulose particles were flat objects constituted by elementary crystallites whose lateral adhesion was resistant against hydrolysis and sonication treatments. Moreover, tunicin whiskers were described as twisted ribbons with an estimated pitch of 2.4-3.2 microm. Length and width distributions of all samples were generally well described by log-normal functions, with the exception of tunicin, which had less lateral aggregation. AFM observation confirmed that the thickness of the nanocrystals was almost constant for a given origin and corresponded to the crystallite size measured from peak broadening in WAXS spectra. Experimental SAXS profiles were numerically simulated, combining the dimensions and size distribution functions determined by the various techniques.

Effect of shear stress on adhering polyelectrolyte capsules.

A parallel plate flow chamber was implemented to study the deformation and adhesion of individual spherical hollow polyelectrolyte multilayered shells adhering to a coated surface. The device provides a well-defined laminar flow allowing the determination of the shear stress to which the capsules are being exposed up to 15 N/m(2). The results of the investigations indicate a strong dependence of the adhesion and mechanical resistance on the capsule size and wall thickness. Thin walled capsules, constituted of 8 polyelectrolyte layers (thickness congruent with 12 nm), are immediately deformed when exposed to flow while thick capsules, constituted of 16 layers (thickness congruent with 24 nm), of equal dimensions are detached from the surface for drag forces below 50 nN. It was observed that adhering capsules exposed to flow undergo an increase in their adhesion area in the direction of flow, resulting in rolling of the capsules. It was also found that the resistance of the capsules decreases after acetone treatment, indicating a weakening of the polyelectrolyte multilayer structure in the presence of this solvent.

Tuning of microcapsule adhesion by varying the capsule-wall thickness.

The adhesion area and topology of spherical hollow polyelectrolyte shells adhering to flat glass or polyelectrolyte-covered glass surfaces are studied. Strong adhesion is found for anionic poly(sodium 4-styrenesulfonate)-terminated shells on cationic poly(ethylene imine)-covered glass, while no adhesion of those shells on uncoated glass is found. The adhering shells are deformed and obtain a truncated sphere topology with a circular adhesion disk. The radius of the adhesion disks can reach up to 50% of the shell radius for shells of several tens of microns. The dependency of the size of adhesion areas on the capsule radius and capsule wall thickness is also investigated. Remarkably, the size of the adhesion areas is found to depend strongly on the wall thickness, which offers interesting perspectives for controlling capsule adhesion properties. A model based on the energy balance of deformation and wetting energies is presented that explains the observed trends.