Radiation and mechanical performance of cementitious materials containing ecofriendly nano laboratory waste glass.

This study helps in managing waste glass and greening the environment by incorporating laboratory waste glass into mortar production to make an eco-friendly shielding material against gamma rays. The efficiency of using waste glass powder as a cement replacement or addition in mortar production was studied by using two waste glass sizes: micro glass (particle size range from 10.09 to 24.73 µm) and nano glass (particle size range from 10.57 to 26.42 nm) to design different mortar specimens with varying percentages of fine glass powder from 0 to 30%. Compressive strength and flexure strength were evaluated to determine mechanical properties. The results indicated that adding WGP to mortar positively affects the characteristics of cementitious composites. The linear and mass attenuation coefficients of the samples were experimentally determined using a NaI detector and various radioactive sources (Am-241, Ba-133, Eu-152, Cs-137, and Co-60) with gamma energies ranging from 59.53 to 1332 keV. The obtained coefficients were then compared to the theoretical values of the composites using XCOM software to verify their accuracy. Additionally, the half-value layer, tenth-value layer, mean free path, and effective atomic number were computed. Furthermore, the results revealed that the mortar sample with 30% nano additive glass was the most effective in reducing gamma radiation.

Impact of nano Fe2O3 on radiation parameters of epoxy reinforced with nano carbon.

This study aims to investigate the effectiveness of iron oxide (Fe2O3) and carbon black in micro and nanoscales incorporated into an epoxy adhesive matrix for gamma-ray attenuation. The composites were prepared via a simple and cost-effective synthesis method. The grain size of powder NPs was measured using a transmission electron microscope (TEM), and the particle size was about 20 ± 5 nm and 31.46 ± 2 nm for carbon and Fe2O3, respectively. The morphological properties were characterized by a scanning electron microscope, which indicated the excellent dispersion of NPs, which blocked almost all pores of the composite and increased the capability of radiation attenuation. In addition, the chemical composition of samples using energy dispersive X-rays (EDX) and the compressive strength were measured. Furthermore, the linear and mass attenuation coefficients were determined experimentally for incident photon energies of 59.51-1408.01 keV emitted from γ-ray sources using the sodium iodide scintillation detector NaI. A comparison was conducted between the experimental data and theoretical results that obtained from XCOM software, examined the validity of the experimental results. The relation deviation rate was found to vary between 0.0008 and 2.83%. Furthermore, the measurement of the relation deviation rate between the linear attenuation coefficients of micro and nano composites revealed a range of values between 1 and 25%. Also, shielding parameters such as half-value layer (HVL), tenth-value layer (TVL), mean free path (MFP), and effective atomic number (Zeff) were measured. Moreover, the equivalent atomic number (Zeq), absorption, and exposure buildup factors for prepared samples were calculated. The results showed that the incorporation of Fe2O3 NPs enhanced the shielding capability of the composites, as evidenced by the significant reduction in gamma-ray transmission. The composite materials exhibited excellent mechanical strength, making them suitable for practical applications in radiation shielding. Furthermore, it was determined that the elevation in N-Fe2O3 concentration resulted in a direct increase in the linear attenuation coefficient, from 0.314 to 0.519 cm-1 at 0.5951 MeV and from 0.099 to 0.124 cm-1 at 0.662 MeV. Nevertheless, a slight increase was discerned in the identified mass attenuation coefficients at 0.1332 and 0.1408 MeV. The experimental data for MFP, HVL, and TVL demonstrate that the EFeC4 sample exhibits optimal performance, with values of 1.9, 1.3, and 4.4 cm at 0.5951 MeV, and at 0.661 MeV, the values are 8.04, 5.57, and 18.52 cm, while at 0.1408 MeV, the values are 12.06, 8.36, and 27.78 cm, respectively. Overall, this research highlights the potential of iron oxide-carbon/epoxy composites as efficient and reliable materials for gamma-ray protection in various fields, including nuclear power plants, medical facilities, and space exploration.

Impact of Bi2O3 on prepared nano (SiO2-Na2O-CaO-B2O3) glass as radiation shielding material.

Melt quenching technique was used to create Bismuth Boro-Silicate nano glasses with compositions of 45SiO2-10CaO- 25Na2O- xBi2O3- (20-x) B2O3 (where x is 0, 5, 10, 15, and 20 mol %). Standard point sources AM-241, Ba-133, Co-60, Cs-137, and Eu-152 were used in the radiation experiment to evaluate the attenuation coefficients spanning the energy range of 59.51 keV to 1048.01 keV. The findings show that adding Bi2O3 in place of B2O3 increases the following: radiation protection efficiency (RPE%), transmission factor (TF%), absorption buildup factor values (ABF), exposure buildup factor values (EBF), mass attenuation coefficients (MACs), linear attenuation coefficients (LACs), and radiation protection efficiency (RPE%). In comparison to lead glass, these findings demonstrate the potential of nano Bismuth Boro-Silicate glass as a radiation shielding material.

Exploring green environmental composites as hosts for shielding materials using experimental, theoretical and Geant4 simulation methods.

Rice straw is considered an agricultural waste harmful to the environment, which is abundant in most parts of the world. From this point, the present study is devoted to preparing new composites of two types of glue based on rice straw as a plentiful, low-cost matrix. Straw glue samples were prepared by mixing 20% wt. of rice straw with 80% wt. of animal glue (RS-An) and polyvinyl acetate (RS-PVAC) at different thicknesses of 1, 2, and 3 cm. The chemical composition of the prepared samples was identified by energy dispersive X-ray analysis and their morphology was examined using a scanning electron microscope. The mechanical test explored that RS-An and RS-PVAC respectively required a stress of 25.2 and 25.5 MPa before reaching the breaking point. γ-ray shielding performance was analyzed and determined at numerous photon energies from 0.059 to 1.408 MeV emitted from five-point γ-rays sources using NaI (Tl). Linear attenuation coefficient was calculated by obtaining the area under the peak of the energy spectrum observed from Genie 2000 software in the presence and absence of the sample. The experimental results of mass attenuation coefficient were compared with theoretical data of XCOM software with relative deviation ranging from 0.10 to 2.99%. Geant4 Monte Carlo simulation code was also employed to validate the experimental results. The relative deviation of XCOM and Geant4 outcomes was 0.09-1.77%, which indicates a good agreement between them. Other radiation shielding parameters such as half value layer (HVL), tenth value layer, and mean free path were calculated in three ways: experimentally, theoretically from the XCOM database, and by simulation using Geant4 code. Additionally, effective atomic number (Zeff), effective atomic number (Neff), equivalent atomic number (Zeq), and buildup factors were evaluated. It was confirmed that the γ-ray shielding properties were further boosted by mixing rice straw with the animal glue compared to the synthetic one.

Polyurethane reinforced with micro/nano waste slag as a shielding panel for photons (experimental and theoretical study).

This study not only provides an innovative technique for producing rigid polyurethane foam (RPUF) composites, but it also offers a way to reuse metallurgical solid waste. Rigid polyurethane (RPUF) composite samples have been prepared with different proportions of iron slag as additives, with a range of 0-25% mass by weight. The process of grinding iron slag microparticles into iron slag nanoparticles powder was accomplished with the use of a high-energy ball mill. The synthesized samples have been characterized using Fourier Transform Infrared Spectroscopy, and Scanning Electron Microscope. Then, their radiation shielding properties were measured by using A hyper-pure germanium detector using point sources 241Am, 133 BA, 152 EU, 137Cs, and 60Co, with an energy range of 0.059-1.408 MeV. Then using Fluka simulation code to validate the results in the energy range of photon energies of 0.0001-100 MeV. The linear attenuation coefficient, mass attenuation coefficient, mean free path, half-value layer and tenth-value layer, were calculated to determine the radiation shielding characteristics of the composite samples. The calculated values are in good agreement with the calculated values. The results of this study showed that the gamma-ray and neutron attenuation parameters of the studied polyurethane composite samples have improved. Moreover, the effect of iron slag not only increases the gamma-ray attenuation shielding properties but also enhances compressive strength and the thermal stability. Which encourages us to use polyurethane iron-slag composite foam in sandwich panel manufacturing as walls to provide protection from radiation and also heat insulation.

Impact of (nano ZnO/multi-wall CNTs) prepared by arc discharge method on the removal efficiency of stable iodine 127I and radioactive iodine 131I from water.

Radioactive iodine isotopes especially 131I are used for diagnosis and treatment of different types of cancer diseases. Due to the leak of radioactive iodine into the patient's urine in turn, the wastewater would be contaminated, so it is worth preparing a novel adsorption green material to remove the radioactive iodine from wastewater efficiently. The removal of 127I and 131I contaminants from aqueous solution is a problem of interest. Therefore, this work presents a new study for removing the stable iodine 127I- and radioactive iodine 131I from aqueous solutions by using the novel nano adsorbent (Nano ZnO/MWCNTs) which is synthesized by the arc discharge method. It is an economic method for treating contaminated water from undesired dissolved iodine isotopes. The optimal conditions for maximum removal are (5 mg/100 ml) as optimum dose with shacking (200 rpm) for contact time of (60 min), at (25 °C) in an acidic medium of (pH = 5). After the adsorption process, the solution is filtrated and the residual iodide (127I-) is measured at a maximum UV wavelength absorbance of 225 nm. The maximum adsorption capacity is (15.25 mg/g); therefore the prepared nano adsorbent (Nano ZnO/MWCNTs) is suitable for treating polluted water from low iodide concentrations. The adsorption mechanism of 127I- on to the surface of (Nano ZnO/MWCNTs) is multilayer physical adsorption according to Freundlich isotherm model and obeys the Pseudo-first order kinetic model. According to Temkin isotherm model the adsorption is exothermic. The removal efficiency of Nano ZnO/MWCNTs for stable iodine (127I-) from aqueous solutions has reached 97.23%, 89.75%, and 64.78% in case of initial concentrations; 0.1843 ppm, 0.5014 ppm and 1.0331 ppm, respectively. For the prepared radio iodine (131I-) solution of radioactivity (20 µCi), the dose of nano adsorbent was (10 mg/100 ml) and the contact time was (60 min) at (pH = 5) with shacking (200 rpm) at (25 °C). The filtration process was done by using a syringe filter of a pore size (450 nm) after 2 days to equilibrate. The removal efficiency reached (34.16%) after the first cycle of treatment and the percentage of residual radio iodine was (65.86%). The removal efficiency reached (94.76%) after five cycles of treatment and the percentage of residual radio iodine was (5.24%). This last percentage was less than (42.15%) which produces due to the natural decay during 10 days.

Novel composite based on silicone rubber and a nano mixture of SnO2, Bi2O3, and CdO for gamma radiation protection.

Recently, there has been a surge of interest in the application of radiation-shielding materials. One promising research avenue involves using free-lead metal oxides/polymer composites, which have been studied for their radiation shielding and characterization properties. This study reinforced the dimethylpolysiloxane (silicone rubber) composites with micro- and nano-sized particles of tin oxide, cadmium oxide, and bismuth oxide as additive materials. The composites were tested with 20 and 50 weight fractions, and their attenuation coefficients were measured using a NaI(TI) detector at gamma-ray energies ranging from 59.54 to 1408.01 keV. Also, the thermal and mechanical properties of the composites were observed and compared with those of free silicone rubber. The results showed that the 50% nano metal oxide/SR composites exhibited better thermal stability and attenuation properties than the other composites, also possessing unique attributes such as lightweight composition and exceptional flexibility. Consequently, this composite material holds immense potential for safeguarding vital organs, including the eyes and gonads, during radiological diagnosis or treatment procedures. Its exceptional ability to absorb a significant portion of incident rays makes it an invaluable asset in the field of radiation protection.

Attenuation properties of poly methyl methacrylate reinforced with micro/nano ZrO2 as gamma-ray shields.

This research aimed to examine the radiation shielding properties of unique polymer composites for medical and non-medical applications. For this purpose, polymer composites, based on poly methyl methacrylate (PMMA) as a matrix, were prepared and reinforced with micro- and nanoparticles of ZrO2 fillers at a loading of 15%, 30%, and 45% by weight. Using the high purity germanium (HPGe) detector, the suggested polymer composites' shielding characteristics were assessed for various radioactive sources. The experimental values of the mass attenuation coefficients (MAC) of the produced composites agreed closely with those obtained theoretically from the XCOM database. Different shielding parameters were estimated at a broad range of photon energies, including the linear attenuation coefficient (µ), tenth value layer (TVL), half value layer (HVL), mean free path (MFP), effective electron density (Neff), effective atomic number (Zeff), and equivalent atomic number (Zeq), as well as exposure buildup factor (EBF) and energy absorption buildup factor (EABF) to provide more shielding information about the penetration of γ-rays into the chosen composites. The results showed that increasing the content of micro and nano ZrO2 particles in the PMMA matrix increases µ values and decreases HVL, TVL, and MFP values. P-45nZ sample with 45 wt% of ZrO2 nanoparticles had the highest µ values, which varied between 2.6546 and 0.0991 cm-1 as γ-ray photon energy increased from 0.0595 to 1.408 MeV, respectively. Furthermore, the highest relative increase rate in µ values between nano and micro composites was 17.84%, achieved for the P-45nZ sample at 59.53 keV. These findings demonstrated that ZrO2 nanoparticles shield radiation more effectively than micro ZrO2 even at the same photon energy and filler wt%. Thus, the proposed nano ZrO2/PMMA composites can be used as effective shielding materials to lessen the transmitted radiation dose in radiation facilities.

Developing of Lead/Polyurethane Micro/Nano Composite for Nuclear Shielding Novel Supplies: γ-Spectroscopy and FLUKA Simulation Techniques.

In this work, the effect of adding Pb nano/microparticles in polyurethane foams to improve thermo-physical and mechanical properties were investigated. Moreover, an attempt has been made to modify the micron-sized lead metal powder into nanostructured Pb powder using a high-energy ball mill. Two types of fillers were used, the first is Pb in micro scale and the second is Pb in nano scale. A lead/polyurethane nanocomposite is made using the in-situ polymerization process. The different characterization techniques describe the state of the dispersion of fillers in foam. The effects of these additions in the foam were evaluated, Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD) have all been used to analyze the morphology and dispersion of lead in polyurethane. The findings demonstrate that lead is uniformly distributed throughout the polyurethane matrix. The compression test demonstrates that the inclusion of lead weakens the compression strength of the nanocomposites in comparison to that of pure polyurethane. The TGA study shows that the enhanced thermal stability is a result of the inclusion of fillers, especially nanofillers. The shielding efficiency has been studied, MAC, LAC, HVL, MFP and Zeff were determined either experimentally or by Monte Carlo calculations. The nuclear radiation shielding properties were simulated by the FLUKA code for the photon energy range of 0.0001-100 MeV.

Impact of micro/nano cadmium oxide on shielding properties of cement-ball clay matrix.

This study investigates the gamma radiation shielding properties of cement-ball clay matrix composites doped with micro- and nano-sized cadmium oxide (CdO) particles. The linear attenuation coefficient (LAC) was determined using a sodium iodide (NaI) detector and five radioactive point sources with energies ranging from 59.5 to 1408 keV. The LAC values obtained were compared to the XCOM database and found to be in good agreement. The composites' half-value layer (HVL), tenth value layer (TVL), mean free path (MFP), effective atomic number (Zeff), equivalent atomic number (Zeq), and absorption buildup factor (EABF) were determined. The results showed that the addition of CdO particles improved the radiation-shielding behavior of the composites and increasing the weight fraction of CdO particles increased the shielding effectiveness. The results also illustrated that when nano-sized CdO particles were compared to their micro-sized counterparts, there was a significant enhancement in radiation shielding effectiveness. For instance, a composite material composed of 50% cement, 41.7% ball clay, and 3.8% nano CdO at an energy level of 0.0595 MeV exhibited a remarkable 12.2% increase in attenuation, surpassing the performance of the micro-sized sample with an equivalent concentration. Similarly, another composite consisting of 50% cement, 33.3% ball clay, and 16.7% nano CdO demonstrated a significant 15.4% increase in attenuation at the same energy level, when compared to the micro-sized sample. The study demonstrates the potential of CdO-doped cement-ball clay matrix composites for gamma radiation shielding applications.

Novel slag/natural rubber composite as flexible material for protecting workers against radiation hazards.

This work is an attempt to employ the electric arc furnace (EAF) slag as a by-product material to develop an alternative and environmentally friendly material for gamma-radiation protection applications such as in medical and industrial areas. For this purpose, different concentrations of micro-sized EAF slag (0, 20, 40, 60, 80, 100, 500, and 800 phr) were incorporated as fillers in the natural rubber (NR) matrix to produce the shielding composites. In addition, nano-sized EAF slag particles were prepared by using a high-energy ball milling technique to investigate the effect of particle size on the gamma-radiation shielding properties. The synthesized micro and nano EAF/NR composites were tested as protective materials against gamma-radiation by employing NaI(Tl) scintillation detector and standard radioactive point sources (152Eu, 137Cs, 133Ba, and 60Co). Different shielding parameters such as linear and mass attenuation coefficient, half value layer (HVL), tenth value layer, mean free path, effective atomic number (Zeff), and effective electron density (Neff) were determined to assess the radiation shielding capability of the EAF/NR composites. Furthermore, equivalent atomic number (Zeq) and the exposure buildup factor values for photon energy in the range from 0.015 to 15 MeV were also computed by Geometric Progression method. The experimental results of micro EAF/NR composites showed that at 121.78 keV, EAF0 composite (without EAF slag content) had the lowest µ value of 0.1695 cm-1, while the EAF800 composite (which was loaded with 800 phr of micro EAF slag) had the highest µ value of 0.2939 cm-1 at the same energy, which in turn decreases the HVL from 4.09 to 2.36 cm, respectively. Therefore, increasing the filler weight fractions of EAF slag in the NR matrix, increases the shielding properties of the composites. Moreover, the NR composite reinforced with 800 phr of nano EAF slag has better gamma-radiation shielding efficiency compared to that filled with 800 phr of micro EAF slag. The success of this work was to prepare a flexible, lightweight, low-cost, and lead-free material with better shielding capability.

Radiation attenuation properties of chemically prepared MgO nanoparticles/HDPE composites.

Sheets of high-density polyethylene (HDPE) loaded with magnesium oxide in micro and nano were synthesized with different weight percentages of micro-MgO (0,5,10,20 and 30% by weight) and nano-MgO (5 and 30%) and shaped in form of disc and dog bone shape. The morphological, mechanical, and attenuation characteristics of each concentration were determined. The linear attenuation coefficients (LAC) of the prepared discs were calculated using a well-calibrated scintillation detector and five standard gamma-ray point sources (241Am, 133Ba, 137Cs, 60Co and 152Eu). The LAC was theoretically calculated for HDPE/micro-MgO composites using XCOM software. A good agreement between the theoretical and experimental results was observed. The comparison between micro and nano-MgO as a filler in HDPE was evaluated. The results proved that the loaded nano-MgO in different proportions of HDPE produced greater attenuation coefficients than its micro counterpart. The addition of nano MgO with different weight percentage led to a significant improvement in the mechanical properties of HDPE, the ultimate force and ultimate stress increased as the concentration of nano MgO increased, and the young modulus of HDPE also increased with increasing concentration of micro and nano MgO.

A New Environmentally Friendly Mortar from Cement, Waste Marble and Nano Iron Slag as Radiation Shielding.

Improving mortar shielding properties to preserve environmental and human safety in radiation facilities is essential. Conventional cement mortars, composed of cement, water, and lime aggregate, are crucial for radiation shielding. Using recycled aggregates to produce new mortar and concrete compositions has attracted the attention of several researchers. In the current study, waste marble and iron slag as aggregates are used to create novel cement mortar compositions to study the aggregate's impact on the radiation attenuation capability of the mortar. Three mortar groups, including a control mortar (CM-Ctrl), were prepared based on cement and waste marble. The other two groups (CM-MIS, CM-NIS), contained 25% iron slag at different particle sizes as a replacement for a waste marble. The study aims to compare iron slag in their micro and nano sizes to discuss the effect of particle size on the mortar radiation capability. For this purpose, the NaI scintillation detector and radioactive point sources (241Am, 133Ba, 137Cs, 60Co, and 152Eu) were utilized to measure several shielding parameters, such as the linear attenuation coefficient (LAC), mass attenuation coefficient (MAC), half-value layer (HVL), tenth-value layer (TVL), and mean free path (MFP), for the produced mortars at different photon energies. Furthermore, the transmission electron microscope (TEM) is used to measure the particle size of the aggregates. In addition, a scanning electron microscope (SEM) is utilized to acquire the cross-section morphologies of the prepared mortars. According to our findings, mortars prepared with nano-iron slag and waste marble offered superior shielding capabilities than mortars containing natural sand or fine crushed stone. The nano iron slag mortar can be utilized in place of typical sand mortar for applications as rendering or plastering materials for building medical diagnostic and CT scanner rooms, due to its improved shielding abilities.

Investigation of Gamma-Ray Shielding Properties of Bismuth Oxide Nanoparticles with a Bentonite-Gypsum Matrix.

Due to the present industrial world, the risk of radioactivity is notably increasing. Thus, an appropriate shielding material needs to be designed to protect humans and the environment against radiation. In view of this, the present study aims to design new composites of the main matrix of bentonite-gypsum with a low-cost, abundant, and natural matrix. This main matrix was intercalated in various amounts with micro- and nanosized particles of bismuth oxide (Bi2O3) as the filler. Energy dispersive X-ray analysis (EDX) recognized the chemical composition of the prepared specimen. The morphology of the bentonite-gypsum specimen was tested using scanning electron microscopy (SEM). The SEM images showed the uniformity and porosity of a cross-section of samples. The NaI (Tl) scintillation detector was used with four radioactive sources (241Am, 137Cs, 133Ba, and 60Co) of various photon energies. Genie 2000 software was used to determine the area under the peak of the energy spectrum observed in the presence and absence of each specimen. Then, the linear and mass attenuation coefficients were obtained. After comparing the experimental results of the mass attenuation coefficient with the theoretical values from XCOM software, it was found that the experimental results were valid. The radiation shielding parameters were computed, including the mass attenuation coefficients (MAC), half-value layer (HVL), tenth-value layer (TVL), and mean free path (MFP), which are dependent on the linear attenuation coefficient. In addition, the effective atomic number and buildup factors were calculated. The results of all of these parameters provided the same conclusion, which confirms the improvement of the properties of γ-ray shielding materials using a mixture of bentonite and gypsum as the main matrix, which is much better than using bentonite alone. Moreover, bentonite mixed with gypsum is a more economical means of production. Therefore, the investigated bentonite-gypsum materials have potential uses in applications such as gamma-ray shielding materials.

Enhancing the Gamma-Radiation-Shielding Properties of Gypsum-Lime-Waste Marble Mortars by Incorporating Micro- and Nano-PbO Particles.

In the current study, the gamma-radiation-shielding characteristics of novel gypsum-lime-waste marble-based mortars reinforced with micro-PbO and nano-PbO powders were investigated. In total, seven mortar groups, including a control mortar (named GLM), were prepared. The other groups contained10, 20, and 30 wt.% of both micro-PbO and nano-PbO as a waste marble replacement. This study aimed to explore the effect of particle size and concentrations of PbO powders on the γ-ray-shielding capability of GLM mortars. For this purpose, an HPGe detector and five standard radioactive point sources (241Am, 133Ba, 137Cs, 60Co, and 152Eu) were employed to measure different shielding parameters, including the linear attenuation coefficient (µ), mass attenuation coefficient (µm), mean free path (MFP), half-value layer (HVL), and tenth-value layer (TVL), for the prepared samples in the energy range between 59.53 keV to 1408.01 keV. On the basis of µm values, other significant shielding parameters such as effective atomic number (Zeff), effective electron density (Neff), equivalent atomic number (Zeq), and exposure buildup factor (EBF) were also computed to explore the potential usage of the proposed mortars as radiation protective materials. The results reported that the smallest HVL, TVL, and MPF, as well as the largest attenuation values, were obtained for mortars reinforced by nano-PbO compared to those containing micro-PbO. It can be concluded from the results that the mortar samples containing nano-PbO had a remarkably improved gamma-radiation-shielding ability. Thus, these mortars can be used for radiation shielding on walls in nuclear facilities to reduce the transmitted radiation dose.

Gamma Attenuation Features of White Cement Mortars Reinforced by Micro/Nano Bi2O3 Particles.

This study aims to explore the radiation protection properties of white mortars based on white cement as a binder and Bi2O3 micro and nanoparticles in proportions of 15 and 30% by weight as replacement sand. The average particle size of micro- and nano-Bi2O3 was measured using a transmission electron microscope (TEM). The cross-sectional morphology and distribution of Bi2O3 within the samples can be obtained by scanning electron microscopy (SEM), showing that nanoscale Bi2O3 particles have a more homogeneous distribution within the samples than microscale Bi2O3 particles. The shielding parameters of the proposed mortars were measured using the HPGe detector at various γ-ray energies emitted by standard radioactive point sources 241Am, 133Ba, 60Co, 137Cs, and 152Eu. The experimental values of the prepared mortars' mass attenuation coefficients (MAC) match well with those determined theoretically from the XCOM database. Other shielding parameters, including half value layer (HVL), tenth value layer (TVL), mean free path (MFP), effective electron density (Neff), effective atomic number (Zeff), equivalent atomic number (Zeq), and exposure buildup factor (EBF), were also determined at different photon energies to provide more shielding information about the penetration of gamma radiation into the selected mortars. The obtained results indicated that the sample containing 30% by weight of nano Bi2O3 has the largest attenuation coefficient value. Furthermore, the results show that the sample with a high concentration of Bi2O3 has the highest equivalent atomic numbers and the lowest HVL, TVL, MFP, and EBF values. Finally, it can be concluded that Bi2O3 nanoparticles have higher efficiency and protection compared to microparticles, especially at lower gamma-ray energies.

Innovative antibacterial electrospun nanofibers mats depending on piezoelectric generation.

This paper introduces a new approach of testing piezoelectric nanofibers as antibacterial mat. In this work, both Polyvinylidene fluoride (PVDF) and PVDF embedded with thermoplastic polyurethane nanofibers are synthesized as nanofibers mat via electrospinning technique. Then, such mat is analyzed as piezoelectric material to generate electric voltage under different mechanical excitations. Furthermore, morphological and chemical characteristics have been operated to prove the existence of beta sheets piezoelectricity of the synthesized nanofibers mats. Then, the synthesized nanofibers surfaces have been cyclically stretched and exposed to bacteria specimen. It has been noticed that the generated voltage and the corresponding localized electric field positively affect the growth of bacteria and reduces the formation of K. penomenue samples bacteria colonies. In addition, the effect of both stretching frequency and pulses numbers have been studied on the bacteria count, growth kinetics, and protein leakage. Our contribution here is to introduce an innovative way of the direct impact of the generated electric field from piezoelectric nanofibers on the reduction of bacteria growth, without depending on traditional anti-bacterial nanoparticles. This work can open a new trend of the usability of piezoelectric nanofibers through masks, filters, and wound curing mats within anti-bacterial biological applications.

Effect of Kaolin Clay and ZnO-Nanoparticles on the Radiation Shielding Properties of Epoxy Resin Composites.

The use of radiation is mandatory in modern life, but the harms of radiation cannot be avoided. To minimize the effect of radiation, protection is required for the safety of the environment and human life. Hence, inventing a better shield than a conventional shielding material is the priority of researchers. Due to this reason, this current research deals with an innovative shielding material named EKZ samples having a composition of (epoxy resin (90-40) wt %-kaolin clay (10-25) wt %-ZnO-nano particles (0-35) wt %). The numerous compositional variations of (epoxy resin, kaolin clay, and ZnO-nano particles on the prepared EKZ samples varied the density of the samples from 1.24 to 1.95 g/cm3. The radiation shielding parameter of linear attenuation coefficient (LAC), half value layer (HVL), tenth value layer (TVL), and radiation protection efficiency (RPE) were measured to evaluate the radiation diffusion efficiency of newly made EKZ samples. These radiation shielding parameters were measured with the help of the HPGe detector utilizing the three-point sources (Am-241, Cs-137, and Co-60). The obtained results exposed that the value of linear attenuation coefficient (LAC) and radiation protection efficiency (RPE) was maximum, yet the value of half value layer (HVL), and tenth value layer (TVL), were minimum due to the greater amount of kaolin clay and ZnO-nanoparticles, whereas the amount of epoxy resin was lesser. In addition, it has been clear that as-prepared EKZ samples are suitable for low-dose shielding applications as well as EKZ-35 showed a better shielding ability.

Effect of PbO-nanoparticles on dimethyl polysiloxane for use in radiation shielding applications.

In this work, morphological and attenuation parameters of gamma ray protection were studied. Dimethyl polysiloxane (Silicon Rubber) Mixed with micro-size and nano-size lead oxide particles at different weight percentage were prepared. The morphological structure of PbO/SR composites was investigated by SEM test, according to SEM images the nano PbO particles are more uniform micro PbO particles. The radiation attenuation test was carried out using 3" × 3" NaI (TI) detector for (Am-241), (Cs-137), (Co-60), (Ba-133), and (Eu-152). The effect on attenuation property of SR-PbO shown that the increase of PbO filler significantly increases the linear attenuation coefficient and improve the other radiation protection parameters especially at low gamma energy. It's found that a significant agreement between the experimental result and theoretical result from Xcom program. In this study it's found matrix filled with nano-PbO have higher gamma shielding ability compared to micro-PbO matrix at the same filler concentration. It can say that SR-nano PbO has a higher radiation protection than SR-micro PbO compositions.

Improving Gamma Ray Shielding Behaviors of Polypropylene Using PbO Nanoparticles: An Experimental Study.

Recently, polymers have entered into many medical and industrial applications. This work aimed to intensively study polypropylene samples (PP) embedded with micro and nanoparticles of PbO for their application in radiation shielding. Samples were prepared by adding 10%, 30%, and 50% by weight of PbO microparticles (mPbO) and adding 10% and 50% PbO nanoparticles (nPbO), in addition to the control sample (pure polypropylene). The morphology of the prepared samples was tested; on the other hand, the shielding efficiency of gamma rays was tested for different sources with different energies. The experimental linear attenuation coefficient (LAC) was determined using a NaI scintillation detector, the experimental results were compared with NIST-XCOM results, and a good agreement was noticed. The LAC was 0.8005 cm-1 for PP-10%nPbO and 0.6283 cm-1 for PP-10%mPbO while was 5.8793 cm-1 for PP-50%nPbO and 3.9268 cm-1 for PP-50%mPbO at 0.060 MeV. The LAC values have been converted to some specific values, such as half value layer (HVL), mean free path (MFP), tenth value layer (TVL), and radiation protection efficiency (RPE) which are useful for discussing the shielding capabilities for gamma-rays. The results of shielding parameters reveal that the PP embedded with nPbO gives better attenuation than its counterpart pp embedded with mPbO at all studied energies.