Gaseous emissions from brake wear can form secondary particulate matter.

Road traffic is an important source of urban air pollutants. Due to increasingly strict controls of exhaust emissions from road traffic, their contribution to the total emissions has strongly decreased over time in high-income countries. In contrast, non-exhaust emissions from road vehicles are not yet legislated and now make up the major proportion of road traffic emissions in many countries. Brake wear, which occurs due to friction between brake linings and their rotating counterpart, is one of the main non-exhaust sources contributing to particle emissions. Since the focus of brake wear emission has largely been on particulate pollutants, little is currently known about gaseous emissions such as volatile organic compounds from braking and their fate in the atmosphere. This study investigates the oxidative ageing of gaseous brake wear emissions generated with a pin-on-disc tribometer, using an oxidation flow reactor. The results demonstrate, for the first time, that the photooxidation of gaseous brake wear emissions can lead to formation of secondary particulate matter, which could amplify the environmental impact of brake wear emissions.

Nicotine interacts with DNA lesions induced by alpha radiation which may contribute to erroneous repair in human lung epithelial cells.

PURPOSE: Epidemiological studies show that radon and cigarette smoke interact in inducing lung cancer, but the contribution of nicotine in response to alpha radiation emitted by radon is not well understood. MATERIALS AND METHODS: Bronchial epithelial BEAS-2B cells were either pre-treated with 2 µM nicotine during 16 h, exposed to radiation, or the combination. DNA damage, cellular and chromosomal alterations, oxidative stress as well as inflammatory responses were assessed to investigate the role of nicotine in modulating responses. RESULTS: Less γH2AX foci were detected at 1 h after alpha radiation exposure (1-2 Gy) in the combination group versus alpha radiation alone, whereas nicotine alone had no effect. Comet assay showed less DNA breaks already just after combined exposure, supported by reduced p-ATM, p-DNA-PK, p-p53 and RAD51 at 1 h, compared to alpha radiation alone. Yet the frequency of translocations was higher in the combination group at 27 h after irradiation. Although nicotine did not alter G2 arrest at 24 h, it assisted in cell cycle progression at 48 h post radiation. A slightly faster recovery was indicated in the combination group based on cell viability kinetics and viable cell counts, and significantly using colony formation assay. Pan-histone acetyl transferase inhibition using PU139 blocked the reduction in p-p53 and γH2AX activation, suggesting a role for nicotine-induced histone acetylation in enabling rapid DNA repair. Nicotine had a modest effect on reactive oxygen species induction, but tended to increase alpha particle-induced pro-inflammatory IL-6 and IL-1ß (4 Gy). Interestingly, nicotine did not alter gamma radiation-induced γH2AX foci. CONCLUSIONS: This study provides evidence that nicotine modulates alpha-radiation response by causing a faster but more error-prone repair, as well as rapid recovery, which may allow expansion of cells with genomic instabilities. These results hold implications for estimating radiation risk among nicotine users.

Toxicity of airborne nanoparticles: Facts and challenges.

Air pollution is one of the most severe environmental healthhazards, and airborne nanoparticles (diameter <100 nm) are considered particularly hazardous to human health. They are produced by various sources such as internal combustion engines, wood and biomass burning, and fuel and natural gas combustion, and their origin, among other parameters, determines their intrinsic toxicity for reasons that are not yet fully understood. Many constituents of the nanoparticles are considered toxic or at least hazardous, including polycyclic aromatic hydrocarbons (PAHs) and heavy metal compounds, in addition to gaseous pollutants present in the aerosol fraction, such as NOx, SO2, and ozone. All these compounds can cause oxidative stress, mitochondrial damage, inflammation in the lungs and other tissues, and cellular organelles. Epidemiological investigations concluded that airborne pollution may affect the respiratory, cardiovascular, and nervous systems. Moreover, particulate matter has been linked to an increased risk of lung cancer, a carcinogenic effect not related to DNA damage, but to the cellular inflammatory response to the pollutants, in which the release of cytokines promotes the proliferation of pre-existing mutated cancer cells. The mechanisms behind toxicity can be investigated experimentally using cell cultures or animal models. Methods for gathering particulate matter have been explored, but standardized protocols are needed to ensure that the samples accurately represent chemical mixtures in the environment. Toxic constituents of nanoparticles can be studied in animal and cellular models, but designing realistic exposure settings is challenging. The air-liquid interface (ALI) system directly exposes cells, mimicking particle inhalation into the lungs. Continuous research and monitoring of nanoparticles and other airborne pollutants is essential for understanding their effects and developing active strategies to mitigate their risks to human and environmental health.

Toxicity and health effects of ultrafine particles: Towards an understanding of the relative impacts of different transport modes.

Exposure to particulate matter (PM) has been associated with a wide range of adverse health effects, but it is still unclear how particles from various transport modes differ in terms of toxicity and associations with different human health outcomes. This literature review aims to summarize toxicological and epidemiological studies of the effect of ultrafine particles (UFPs), also called nanoparticles (NPs, <100 nm), from different transport modes with a focus on vehicle exhaust (particularly comparing diesel and biodiesel) and non-exhaust as well as particles from shipping (harbor), aviation (airport) and rail (mainly subway/underground). The review includes both particles collected in laboratory tests and the field (intense traffic environments or collected close to harbor, airport, and in subway). In addition, epidemiological studies on UFPs are reviewed with special attention to studies aimed at distinguishing the effects of different transport modes. Results from toxicological studies indicate that both fossil and biodiesel NPs show toxic effects. Several in vivo studies show that inhalation of NPs collected in traffic environments not only impacts the lung, but also triggers cardiovascular effects as well as negative impacts on the brain, although few studies compared NPs from different sources. Few studies were found on aviation (airport) NPs, but the available results suggest similar toxic effects as traffic-related particles. There is still little data related to the toxic effects linked to several sources (shipping, road and tire wear, subway NPs), but in vitro results highlighted the role of metals in the toxicity of subway and brake wear particles. Finally, the epidemiological studies emphasized the current limited knowledge of the health impacts of source-specific UFPs related to different transport modes. This review discusses the necessity of future research for a better understanding of the relative potencies of NPs from different transport modes and their use in health risk assessment.

The effect of airborne Palladium nanoparticles on human lung cells, endothelium and blood - A combinatory approach using three in vitro models.

A better understanding of the mechanisms behind adverse health effects caused by airborne fine particles and nanoparticles (NP) is essential to improve risk assessment and identification the most critical particle exposures. While the use of automobile catalytic converters is decreasing the exhausts of harmful gases, concentrations of fine airborne particles and nanoparticles (NPs) from catalytic metals such as Palladium (Pd) are reaching their upper safe level. Here we used a combinatory approach with three in vitro model systems to study the toxicity of Pd particles, to infer their potential effects on human health upon inhalation. The three model systems are 1) a lung system with human lung cells (ALI), 2) an endothelial cell system and 3) a human whole blood loop system. All three model systems were exposed to the exact same type of Pd NPs. The ALI lung cell exposure system showed a clear reduction in cell growth from 24 h onwards and the effect persisted over a longer period of time. In the endothelial cell model, Pd NPs induced apoptosis, but not to the same extent as the most aggressive types of NPs such as TiO2. Similarly, Pd triggered clear coagulation and contact system activation but not as forcefully as the highly thrombogenic TiO2 NPs. In summary, we show that our 3-step in vitro model of the human lung and surrounding vessels can be a useful tool for studying pathological events triggered by airborne fine particles and NPs.

Dry Generation of CeO2 Nanoparticles and Deposition onto a Co-Culture of A549 and THP-1 Cells in Air-Liquid Interface-Dosimetry Considerations and Comparison to Submerged Exposure.

Relevant in vitro assays that can simulate exposure to nanoparticles (NPs) via inhalation are urgently needed. Presently, the most common method employed is to expose lung cells under submerged conditions, but the cellular responses to NPs under such conditions might differ from those observed at the more physiological air-liquid interface (ALI). The aim of this study was to investigate the cytotoxic and inflammatory potential of CeO2 NPs (NM-212) in a co-culture of A549 lung epithelial cells and differentiated THP-1 cells in both ALI and submerged conditions. Cellular dose was examined quantitatively using inductively coupled plasma mass spectrometry (ICP-MS). The role of serum and LPS-priming for IL-1ß release was further tested in THP-1 cells in submerged exposure. An aerosol of CeO2 NPs was generated by using the PreciseInhale® system, and NPs were deposited on the co-culture using XposeALI®. No or minor cytotoxicity and no increased release of inflammatory cytokines (IL-1ß, IL-6, TNFα, MCP-1) were observed after exposure of the co-culture in ALI (max 5 µg/cm2) or submerged (max 22 µg/cm2) conditions. In contrast, CeO2 NPs cause clear IL-1ß release in monocultures of macrophage-like THP-1, independent of the presence of serum and LPS-priming. This study demonstrates a useful approach for comparing effects at various in-vitro conditions.

In vitro genotoxicity of airborne Ni-NP in air-liquid interface.

Studies using advanced toxicological methods enabling in vitro conditions that are more realistic are currently needed for understanding the risks of pulmonary exposure to airborne nanoparticles. Owing to the carcinogenicity of certain nickel compounds, the increased production of nickel nanoparticles (Ni-NPs) raises occupational safety concerns. The aim of this study was to investigate the genotoxicity of airborne Ni-NPs using a recently developed air-liquid interface exposure system. The wild-type Chinese hamster lung fibroblast cell line (V79) was used and cytotoxicity, DNA damage and mutagenicity were studied by testing colony forming efficiency, alkaline DNA unwinding and HPRT mutation assays, respectively. Additionally, co-exposure to a PARP-1 inhibitor was performed to test possible involvement of base excision repair (BER) in repair of Ni-induced DNA damage. The results showed that cell viability was reduced significantly (to 45% and 46%) after 48 hours Ni-NP exposure at concentrations of 0.15 and 0.32 µg cm-2 . DNA damage was significantly increased after Ni-NP exposure in the presence of the BER inhibitor indicating that Ni-NP-induced DNA damages are subsequently repaired by BER. Furthermore, there was no increased HPRT mutation frequency following Ni-NP exposure. In conclusion, this study shows that Ni-NP treatment of lung fibroblasts in an air-liquid interface system that mimics real-life exposure, results in increased DNA strand breaks and reduced cellular viability. These DNA lesions were repaired with BER in an error-free manner without resulting in mutations. This study also underlines the importance of appropriate quantification of the actual exposure concentrations during air-liquid interface exposure studies.

Inter-comparison of personal monitors for nanoparticles exposure at workplaces and in the environment.

Personal monitors based on unipolar diffusion charging (miniDiSC/DiSCmini, NanoTracer, Partector) can be used to assess the individual exposure to nanoparticles in different environments. The charge acquired by the aerosol particles is nearly proportional to the particle diameter and, by coincidence, also nearly proportional to the alveolar lung-deposited surface area (LDSA), the metric reported by all three instruments. In addition, the miniDiSC/DiSCmini and the NanoTracer report particle number concentration and mean particle size. In view of their use for personal exposure studies, the comparability of these personal monitors was assessed in two measurement campaigns. Altogether 29 different polydisperse test aerosols were generated during the two campaigns, covering a large range of particle sizes, morphologies and concentrations. The data provided by the personal monitors were compared with those obtained from reference instruments: a scanning mobility particle sizer (SMPS) for LDSA and mean particle size and a ultrafine particle counter (UCPC) for number concentration. The results indicated that the LDSA concentrations and the mean particle sizes provided by all investigated instruments in this study were in the order of ±30% of the reference value obtained from the SMPS when the particle sizes of the test aerosols generated were within 20-400nm and the instruments were properly calibrated. Particle size, morphology and concentration did not have a major effect within the aforementioned limits. The comparability of the number concentrations was found to be slightly worse and in the range of ±50% of the reference value obtained from the UCPC. In addition, a minor effect of the particle morphology on the number concentration measurements was observed. The presence of particles >400nm can drastically bias the measurement results of all instruments and all metrics determined.

Lung function in asphalt pavers: a longitudinal study.

PURPOSE: To study longitudinal changes in lung function in asphalt pavers and a reference group of road maintenance workers, and to detect possible signs of lung disease by high-resolution computed tomography (HRCT) scans. METHODS: Seventy-five asphalt pavers and 71 road maintenance workers were followed up with questionnaires and measurements of lung function. Not every worker was tested every year, but most of them had four or more measurement points. The 75 asphalt pavers were also invited to have HRCT scans of the lungs at the end of the follow-up period. RESULTS: Mean annual decline in forced vital capacity (FVC) and forced expiratory volume in 1 s (FEV1) of the asphalt pavers was 58 and 35 ml, respectively. Adjusted for age at baseline, packyears of smoking and BMI, the asphalt pavers had a significant excess annual decline in FVC and FEV1 compared to the references. The screedmen, the most exposed group of the asphalt pavers, showed a significantly larger decline in FVC than the other asphalt pavers (P = 0.029). Fine intralobular fibrosis without evident cysts was identified with HRCT in three subjects (4 %). CONCLUSION: We conclude that our findings may indicate an excess annual decline in FVC and FEV1 related to exposure to asphalt fumes. The screedmen, who carry out their work behind and close to the paving machine, had the largest decline in lung function. The finding of adverse pulmonary effects in asphalt pavers calls for better technological solutions to prevent exposure.

Surface passivity largely governs the bioaccessibility of nickel-based powder particles at human exposure conditions.

The European chemical framework REACH requires that hazards and risks posed by chemicals, including alloys and metals, are identified and proven safe for humans and the environment. Therefore, differences in bioaccessibility in terms of released metals in synthetic biological fluids (different pH (1.5-7.4) and composition) that are relevant for different human exposure routes (inhalation, ingestion, and dermal contact) have been assessed for powder particles of an alloy containing high levels of nickel (Inconel 718, 57 wt% nickel). This powder is compared with the bioaccessibility of two nickel-containing stainless steel powders (AISI 316L, 10-12% nickel) and with powders representing their main pure alloy constituents: two nickel metal powders (100% nickel), two iron metal powders and two chromium metal powders. X-ray photoelectron spectroscopy, microscopy, light scattering, and nitrogen absorption were employed for the particle and surface oxide characterization. Atomic absorption spectroscopy was used to quantify released amounts of metals in solution. Cytotoxicity (Alamar blue assay) and DNA damage (comet assay) of the Inconel powder were assessed following exposure of the human lung cell line A549, as well as its ability to generate reactive oxygen species (DCFH-DA assay). Despite its high nickel content, the Inconel alloy powder did not release any significant amounts of metals and did not induce any toxic response. It is concluded, that this is related to the high surface passivity of the Inconel powder governed by its chromium-rich surface oxide. Read-across from the pure metal constituents is hence not recommended either for this or any other passive alloy.

Nickel Release, ROS Generation and Toxicity of Ni and NiO Micro- and Nanoparticles.

Occupational exposure to airborne nickel is associated with an elevated risk for respiratory tract diseases including lung cancer. Therefore, the increased production of Ni-containing nanoparticles necessitates a thorough assessment of their physical, chemical, as well as toxicological properties. The aim of this study was to investigate and compare the characteristics of nickel metal (Ni) and nickel oxide (NiO) particles with a focus on Ni release, reactive oxygen species (ROS) generation, cellular uptake, cytotoxicity and genotoxicity. Four Ni-containing particles of both nano-size (Ni-n and NiO-n) and micron-size (Ni-m1 and Ni-m2) were tested. The released amount of Ni in solution was notably higher in artificial lysosomal fluid (e.g. 80-100 wt% for metallic Ni) than in cell medium after 24h (ca. 1-3 wt% for all particles). Each of the particles was taken up by the cells within 4 h and they remained in the cells to a high extent after 24 h post-incubation. Thus, the high dissolution in ALF appeared not to reflect the particle dissolution in the cells. Ni-m1 showed the most pronounced effect on cell viability after 48 h (alamar blue assay) whereas all particles showed increased cytotoxicity in the highest doses (20-40 µg cm2) when assessed by colony forming efficiency (CFE). Interestingly an increased CFE, suggesting higher proliferation, was observed for all particles in low doses (0.1 or 1 µg cm-2). Ni-m1 and NiO-n were the most potent in causing acellular ROS and DNA damage. However, no intracellular ROS was detected for any of the particles. Taken together, micron-sized Ni (Ni-m1) was more reactive and toxic compared to the nano-sized Ni. Furthermore, this study underlines that the low dose effect in terms of increased proliferation observed for all particles should be further investigated in future studies.

Optimization of an air-liquid interface exposure system for assessing toxicity of airborne nanoparticles.

The use of refined toxicological methods is currently needed for characterizing the risks of airborne nanoparticles (NPs) to human health. To mimic pulmonary exposure, we have developed an air-liquid interface (ALI) exposure system for direct deposition of airborne NPs on to lung cell cultures. Compared to traditional submerged systems, this allows more realistic exposure conditions for characterizing toxicological effects induced by airborne NPs. The purpose of this study was to investigate how the deposition of silver NPs (AgNPs) is affected by different conditions of the ALI system. Additionally, the viability and metabolic activity of A549 cells was studied following AgNP exposure. Particle deposition increased markedly with increasing aerosol flow rate and electrostatic field strength. The highest amount of deposited particles (2.2 µg cm(-2) ) at cell-free conditions following 2 h exposure was observed for the highest flow rate (390 ml min(-1) ) and the strongest electrostatic field (±2 kV). This was estimated corresponding to deposition efficiency of 94%. Cell viability was not affected after 2 h exposure to clean air in the ALI system. Cells exposed to AgNPs (0.45 and 0.74 µg cm(-2) ) showed significantly (P < 0.05) reduced metabolic activities (64 and 46%, respectively). Our study shows that the ALI exposure system can be used for generating conditions that were more realistic for in vitro exposures, which enables improved mechanistic and toxicological studies of NPs in contact with human lung cells.Copyright © 2016 The Authors Journal of Applied Toxicology Published by John Wiley & Sons Ltd.

Inflammatory markers and exposure to airborne particles among workers in a Swedish pulp and paper mill.

PURPOSE: To study the relationship between exposure to airborne particles in a pulp and paper mill and markers of inflammation and coagulation in blood. METHODS: Personal sampling of inhalable dust was performed for 72 subjects working in a Swedish pulp and paper mill. Stationary measurements were used to study concentrations of total dust, respirable dust, PM10 and PM2.5, the particle surface area and the particle number concentrations. Markers of inflammation, interleukins (IL-1b, IL-6, IL-8, and IL-10), C-reactive protein (CRP), serum amyloid A (SAA), and fibrinogen and markers of coagulation factor VIII, von Willebrand, plasminogen activator inhibitor, and D-dimer were measured in plasma or serum. Sampling was performed on the last day of the work free period of 5 days, before and after the shift the first day of work and after the shifts the second and third day. In a mixed model analysis, the relationship between particulate exposures and inflammatory markers was determined. Sex, age, smoking, and BMI were included as covariates. RESULTS: The average 8-h time-weighted average (TWA) air concentration levels of inhalable dust were 0.30 mg/m(3), range 0.005-3.3 mg/m(3). The proxies for average 8-h TWAs of respirable dust were 0.045 mg/m(3). Significant and consistent positive relations were found between several exposure metrics (PM 10, total and inhalable dust) and CRP, SAA and fibrinogen taken post-shift, suggesting a dose-effect relationship. CONCLUSION: This study supports a relationship between occupational particle exposure and established inflammatory markers, which may indicate an increased risk of cardiovascular disease.

Intracellular uptake and toxicity of Ag and CuO nanoparticles: a comparison between nanoparticles and their corresponding metal ions.

UNLABELLED: An increased understanding of nanoparticle toxicity and its impact on human health is essential to enable a safe use of nanoparticles in our society. The aim of this study is to investigate the role of a Trojan horse type mechanism for the toxicity of Ag-nano and CuO-nano particles and their corresponding metal ionic species (using CuCl2 and AgNO3 ), i.e., the importance of the solid particle to mediate cellular uptake and subsequent release of toxic species inside the cell. The human lung cell lines A549 and BEAS-2B are used and cell death/membrane integrity and DNA damage are investigated by means of trypan blue staining and the comet assay, respectively. Chemical analysis of the cellular dose of copper and silver is performed using atomic absorption spectroscopy. Furthermore, transmission electron microscopy, laser scanning confocal microscopy, and confocal Raman microscopy are employed to study cellular uptake and particle-cell interactions. The results confirm a high uptake of CuO-nano and Ag-nano compared to no, or low, uptake of the soluble salts. CuO-nano induces both cell death and DNA damage whereas CuCl2 induces no toxicity. The opposite is observed for silver, where Ag-nano does not cause any toxicity, whereas AgNO3 induces a high level of cell death. IN CONCLUSION: CuO-nano toxicity is predominantly mediated by intracellular uptake and subsequent release of copper ions, whereas no toxicity is observed for Ag-nano due to low release of silver ions within short time periods.

Cellular dose of partly soluble Cu particle aerosols at the air-liquid interface using an in vitro lung cell exposure system.

BACKGROUND: There is currently a need to develop and test in vitro systems for predicting the toxicity of nanoparticles. One challenge is to determine the actual cellular dose of nanoparticles after exposure. METHODS: In this study, human epithelial lung cells (A549) were exposed to airborne Cu particles at the air-liquid interface (ALI). The cellular dose was determined for two different particle sizes at different deposition conditions, including constant and pulsed Cu aerosol flow. RESULTS: Airborne polydisperse particles with a geometric mean diameter (GMD) of 180 nm [geometric standard deviation (GSD) 1.5, concentration 10(5) particles/mL] deposited at the ALI yielded a cellular dose of 0.4-2.6 µg/cm(2) at pulsed flow and 1.6-7.6 µg/cm(2) at constant flow. Smaller polydisperse particles in the nanoregime (GMD 80 nm, GSD 1.5, concentration 10(7) particles/mL) resulted in a lower cellular dose of 0.01-0.05 µg/cm(2) at pulsed flow, whereas no deposition was observed at constant flow. Exposure experiments with and without cells showed that the Cu particles were partly dissolved upon deposition on cells and in contact with medium. CONCLUSIONS: Different cellular doses were obtained for the different Cu particle sizes (generated with different methods). Furthermore, the cellular doses were affected by the flow conditions in the cell exposure system and the solubility of Cu. The cellular doses of Cu presented here are the amount of Cu that remained on the cells after completion of an experiment. As Cu particles were partly dissolved, Cu (a nonnegligible contribution) was, in addition, present and analyzed in the nourishing medium present beneath the cells. This study presents cellular doses induced by Cu particles and demonstrates difficulties with deposition of nanoparticles at the ALI and of partially soluble particles.

Characterisation of nano- and micron-sized airborne and collected subway particles, a multi-analytical approach.

Continuous daily measurements of airborne particles were conducted during specific periods at an underground platform within the subway system of the city center of Stockholm, Sweden. Main emphasis was placed on number concentration, particle size distribution, soot content (analyzed as elemental and black carbon) and surface area concentration. Conventional measurements of mass concentrations were conducted in parallel as well as analysis of particle morphology, bulk- and surface composition. In addition, the presence of volatile and semi volatile organic compounds within freshly collected particle fractions of PM(10) and PM(2.5) were investigated and grouped according to functional groups. Similar periodic measurements were conducted at street level for comparison. The investigation clearly demonstrates a large dominance in number concentration of airborne nano-sized particles compared to coarse particles in the subway. Out of a mean particle number concentration of 12000 particles/cm(3) (7500 to 20000 particles/cm(3)), only 190 particles/cm(3) were larger than 250 nm. Soot particles from diesel exhaust, and metal-containing particles, primarily iron, were observed in the subway aerosol. Unique measurements on freshly collected subway particle size fractions of PM(10) and PM(2.5) identified several volatile and semi-volatile organic compounds, the presence of carcinogenic aromatic compounds and traces of flame retardants. This interdisciplinary and multi-analytical investigation aims to provide an improved understanding of reported adverse health effects induced by subway aerosols.

Effect of sonication and serum proteins on copper release from copper nanoparticles and the toxicity towards lung epithelial cells.

Abstract Different methodological settings can influence particle characteristics and toxicity in nanotoxicology. The aim of this study was to investigate how serum proteins and sonication of Cu nanoparticle suspensions influence the properties of the nanoparticles and toxicological responses on human lung epithelial cells. This was investigated by using methods for particle characterization (photon correlation spectroscopy and TEM) and Cu release (atomic absorption spectroscopy) in combination with assays for analyzing cell toxicity (MTT-, trypan blue- and Comet assay). The results showed that sonication of Cu nanoparticles caused decreased cell viability and increased Cu release compared to non-sonicated particles. Furthermore, serum in the cell medium resulted in less particle agglomeration and increased Cu release compared with medium without serum, but no clear difference in toxicity was detected. Few cells showed intracellular Cu nanoparticles due to fast release/dissolution processes of Cu. In conclusion; sonication can affect the toxicity of nanoparticles.

Inflammatory markers and exposure to occupational air pollutants.

OBJECTIVES: To study the possible relationship between inhalation of airborne particles in the work environment and inflammatory markers in blood. METHODS: Total dust was sampled in the breathing zone of 73 subjects working with welding, cutting, grinding and in foundries such as iron, aluminium, and concrete. Stationary measurements were used to study different size fractions of particles including respirable dust, particulate matter (PM)(10) and PM(2.5), the particle number concentration, the number of particles deposited in the alveoli, and total particle surface area concentration. Inflammatory markers such as interleukin-6 (IL-6), C-reactive protein (CRP), fibrinogen, d-dimer, and urate were measured in plasma or serum before the first shift after the summer vacation and after the first, second, and fourth shift. RESULTS: The mean level of total dust in the breathing zone was 0.93 mg/m(3). The proxies for mean respirable dust fraction was 0.27 mg/m(3), PM(10) 0.60 mg/m(3), and PM(2.5) was 0.31 mg/m(3). The IL-6 values increased by 50% after the first day, but decreased after shift on the second and fourth day. CRP did not increase after the first shift but increased by 17% after the second shift. Other biomarkers were unaffected. A multiple linear regression analysis of a subgroup of 47 subjects showed a statistically significant positive relationship between particle exposure and post-shift IL-6. CONCLUSION: This study supports previous investigations observing increases of IL-6 at air concentrations of PM(10) or PM(2.5) between 0.13 and 0.3 mg/m(3) among healthy subjects. This increase of IL-6 may indicate an increased risk of coronary heart disease.

Ultrafine particle characteristics in seven industrial plants.

Ultrafine particles are considered as a possible cause of some of the adverse health effects caused by airborne particles. In this study, the particle characteristics were measured in seven Swedish industrial plants, with a special focus on the ultrafine particle fraction. Number concentration, size distribution, surface area concentration, and mass concentration were measured at 10 different job activities, including fettling, laser cutting, welding, smelting, core making, moulding, concreting, grinding, sieving powders, and washing machine goods. A thorough particle characterization is necessary in workplaces since it is not clear yet which choice of ultrafine particle metric is the best to measure in relation to health effects. Job activities were given a different order of rank depending on what particle metric was measured. An especially high number concentration (130 x 10(3) cm(-3)) and percentage of ultrafine particles (96%) were found at fettling of aluminium, whereas the highest surface area concentration (up to 3800 mum(2) cm(-3)) as well as high PM10 (up to 1 mg m(-3)) and PM1 (up to 0.8 mg m(-3)) were found at welding and laser cutting of steel. The smallest geometric mean diameter (22 nm) was found at core making (geometric standard deviation: 1.9).

Surface characteristics, copper release, and toxicity of nano- and micrometer-sized copper and copper(II) oxide particles: a cross-disciplinary study.

An interdisciplinary and multianalytical research effort is undertaken to assess the toxic aspects of thoroughly characterized nano- and micrometer-sized particles of oxidized metallic copper and copper(II) oxide in contact with cultivated lung cells, as well as copper release in relevant media. All particles, except micrometer-sized Cu, release more copper in serum-containing cell medium (supplemented Dulbecco's minimal essential medium) compared to identical exposures in phosphate-buffered saline. Sonication of particles for dispersion prior to exposure has a large effect on the initial copper release from Cu nanoparticles. A clear size-dependent effect is observed from both a copper release and a toxicity perspective. In agreement with greater released amounts of copper per quantity of particles from the nanometer-sized particles compared to the micrometer-sized particles, the nanometer particles cause a higher degree of DNA damage (single-strand breaks) and cause a significantly higher percentage of cell death compared to cytotoxicity induced by micrometer-sized particles. Cytotoxic effects related to the released copper fraction are found to be significantly lower than the effects related to particles. No DNA damage is induced by the released copper fraction.