Low cost UVA-LED as a radiation source for the photo-Fenton process: a new approach for micropollutant removal from urban wastewater.

Light Emitting Diode (LED) technology has matured sufficiently to be considered as an alternative UVA radiation source in photoreactors. Currently, low energy consuming LEDs with a wide range of wavelengths and radiant flux are readily available. In this study, UVA-LEDs were used as a radiation source for the photo-Fenton process as tertiary treatment. The water matrix used was a simulated secondary effluent doped with 200 µg L-1 of the pesticide acetamiprid (ACTM) due to its recalcitrant nature. All experiments were carried out in a LED-box reactor at pH 2.8. The main purpose of this research was to gain some insight into the relationships among energy supply, LED consumption, UVA irradiance and reaction rate. The effect of LED wavelength on energy efficiency for ACTM degradation was studied by varying the iron concentration and liquid depth. Three wavelengths (365, 385 and 400 nm) and two iron concentrations (5 and 11 mg L-1) for two different liquid depths (5 and 15 cm) were evaluated in order to obtain more energy efficient conditions. The results suggest that while the wavelength of 365 nm with 11 mg Fe2+ L-1 was the best condition for ACTM degradation, the wavelength of 385 nm had slower kinetics, but higher energy efficiency.

Inactivation of natural enteric bacteria in real municipal wastewater by solar photo-Fenton at neutral pH.

This study analyses the use of the solar photo-Fenton treatment in compound parabolic collector photo-reactors at neutral pH for the inactivation of wild enteric Escherichia coli and total coliform present in secondary effluents of a municipal wastewater treatment plant (SEWWTP). Control experiments were carried out to find out the individual effects of mechanical stress, pH, reactants concentration, and UVA radiation as well as the combined effects of UVA-Fe and UVA-H2O2. The synergistic germicidal effect of solar-UVA with 50 mg L(-1) of H2O2 led to complete disinfection (up to the detection limit) of total coliforms within 120 min. The disinfection process was accelerated by photo-Fenton, achieving total inactivation in 60 min reducing natural bicarbonate concentration found in the SEWWTP from 250 to 100 mg L(-1) did not give rise to a significant enhancement in bacterial inactivation. Additionally, the effect of hydrogen peroxide and iron dosage was evaluated. The best conditions were 50 mg L(-1) of H2O2 and 20 mg L(-1) of Fe(2+). Due to the variability of the SEWWTP during autumn and winter seasons, the inactivation kinetic constant varied between 0.07 ± 0.04 and 0.17 ± 0.04 min(-1). Moreover, the water treated by solar photo-Fenton fulfilled the microbiological quality requirement for wastewater reuse in irrigation as per the WHO guidelines and in particular for Spanish legislation.

A new bioseed for determination of wastewater biodegradability: analysis of the experimental procedure.

A new bioassay proposed in the patent P201300029 was applied to a pre-treated wastewater containing a mixture of commercial pesticides to simulate a recalcitrant industrial wastewater in order to determine its biodegradability. The test uses a mixture of standardized inoculum of the lyophilized bacteria Pseudomonas putida with the proper proportion of salts and minerals. The results highlight that biodegradation efficiency can be calculated using a gross parameter (chemical oxygen demand (COD)) which facilitates the biodegradability determination for routine water biodegradability analysis. The same trend was observed throughout the assay with the dehydrated and fresh inoculums, and only a difference of 5% in biodegradation efficiency (E f) was observed. The obtained results showed that the P. putida biodegradability assay can be used as a commercial test with a lyophilized inoculum in order to monitor the ready biodegradability of an organic pollutant or a WWTP influent. Moreover, a combination of the BOD5/COD ratio and the P. putida biodegradability test is an attractive alternative in order to evaluate the biodegradability enhancement in water pre-treated with advanced oxidation processes (AOPs).

Water disinfection using photo-Fenton: Effect of temperature on Enterococcus faecalis survival.

The photo-Fenton process is a promising alternative to classical water disinfection treatments, although information in this regard is scarce due to its operational limitations. The effect of temperature (10, 20, 30 and 40 °C) was studied on water disinfection using the photo-Fenton reaction at initial near neutral pH with resorcinol as a model of natural organic matter (NOM). Enterococcus faecalis, a Gram-positive microorganism, was selected as an indicator of wastewater faecal contamination. The individual effects of different variables involved in this process (mechanical stress, UVA, H(2)O(2), Fe(2+), H(2)O(2)/Fe(2+), UVA/Fe(2+), UVA/H(2)O(2) and UVA/H(2)O(2)/Fe(2+)) were determined. UVA and H(2)O(2) led to a 2.5-log decrease individually and the combined effect of both variables managed to disinfect up to the detection limit (i.e. from a 5.5 to a 6-log reduction) over the same treatment time. Only by adding 10 mg L(-1) of Fe(2+), the inactivation time was reduced from 120 min (H(2)O(2)/UVA) to 80 min (H(2)O(2)/UVA/Fe(2+); photo-Fenton) with 120 mg L(-1) of H(2)O(2). A higher disinfection result for E. faecalis was observed by increasing temperature according to the Arrhenius equation in the photo-Fenton process. The detection limit was not reached at 10 °C and, to achieve the detection limit at 20, 30 and 40 °C, 80, 65 and 40 min were needed, respectively. The decrease in treatment time is a key factor in applying the photo-Fenton disinfection process to a wastewater treatment plant.