Differences in brain-derived neurotrophic factor gene polymorphisms between acute ischemic stroke patients and healthy controls in the Han population of southwest China.

Single-nucleotide polymorphisms in the brain-derived neurotrophic factor gene may affect the secretion and function of brain-derived neurotrophic factor, thereby affecting the occurrence, severity and prognosis of ischemic stroke. This case-control study included 778 patients (475 males and 303 females, mean age of 64.0 ± 12.6 years) in the acute phase of ischemic stroke and 865 control subjects (438 males and 427 females, mean age of 51.7 ± 14.7 years) from the Department of Neurology, West China Hospital, Sichuan University, China between September 2011 and December 2014. The patients' severities of neurological deficits in the acute phase were assessed using the National Institutes of Health Stroke Scale immediately after admission to hospital. The ischemic stroke patients were divided into different subtypes according to the Trial of Org 10172 in Acute Stroke Treatment classification. Early prognosis was evaluated using the Modified Rankin Scale when the patients were discharged. Genomic DNA was extracted from peripheral blood of participants. Genotyping of rs7124442 and rs6265 was performed using Kompetitive Allele Specific polymerase chain reaction genotyping technology. Our results demonstrated that patients who carried the C allele of the rs7124442 locus had a lower risk of poor prognosis than the T allele carriers (odds ratio [OR] = 0.67; 95% confidence interval [CI]: 0.45-1.00; P = 0.048). The patients with the CC or TC genotype also exhibited lower risk than TT carriers (OR = 0.65; 95% CI: 0.42-1.00; P = 0.049). The AA genotype at the rs6265 locus was associated with the occurrence of ischemic stroke in patients with large-artery atherosclerosis (OR = 0.58; 95% CI: 0.37-0.90; P = 0.015). We found that the C allele (CC and TC genotypes) at the rs7124442 locus may be protective for the prognosis of ischemic stroke. The AA genotype at the rs6265 locus is likely a protective factor against the occurrence of ischemic stroke in patients with large-artery atherosclerosis. The study protocol was approved by the Ethics Committee of West China Hospital of Sichuan University, China (approval ID number 2008[4]) on July 25, 2008.

A Technique for Digital Impression and Bite Registration for a Single Edentulous Arch.

Few studies have reported the application of digital technology for the process of impression and interocclusal recordings in edentulous patients. This article describes a digitizing system for generating digital edentulous models with a jaw relationship by taking direct digital impressions and a virtual bite registration using intraoral digital scanning. A specialized scan retractor was used to make digital impressions of edentulous jaws in patients' mouths using an intraoral scanner. Virtual bite registration was obtained with optical scanning of the buccal surfaces of both jaws at the occlusal vertical dimension. The registration was then used as a reference for aligning both jaws. Digital edentulous models that include the jaw relationship would be clinically beneficial for the fabrication of complete dentures in edentulous patients.

A CAD-CAM technique for conversion of interim-to-definitive restoration in patients with complete edentulism.

An interim restoration is a prototype for the definitive prosthesis and preserves the occlusal information and the original vertical dimension of the occlusion. Several techniques have been developed to transfer the information from implant-supported fixed interim to definitive restoration. However, these conventional techniques have limitations, and they are time-consuming, require making impressions and stone casts, and mounting in an articulator. The purpose of this article was to describe a digital technique to accurately transfer the information from complete-arch implant interim restoration to definitive restorations without using definitive casts.

Digital immediate denture: A clinical report.

Fabricating an immediate complete denture in the conventional manner may be complicated and difficult. The purpose of this article was to describe a fully digital workflow used to fabricate an immediate complete denture before removing the teeth and without the use of conventional impressions or stone casts. The digital data for the workflow were acquired using an intraoral scanner and were then used to design the denture base and teeth after deleting any remaining tooth images from the virtual 3-dimensional image of the jaw. The resulting data were exported to a milling machine for denture fabrication.

Digital intraoral scanning technique for edentulous jaws.

Few studies have evaluated direct digital scans of edentulous jaws using intraoral scanners because it is difficult to scan edentulous sites that are smooth and devoid of features. A scanning technique is introduced for making direct digital scans of edentulous jaws with intraoral scanners in patients with a broad palate.

Development of complete dentures based on digital intraoral impressions-Case report.

PATIENT: A 60-year-old man presented for refabrication of his maxillary complete denture. In this case, a digital process was chosen to replace the ill-fitted complete maxillary denture. A specialized scan retractor was used to retract the mobile tissues of the lips, cheeks and vestibule while taking a digital impression. The interocclusal record obtained in the patient's mouth was scanned in order to digitally register the occlusal vertical dimension. The denture base and teeth were designed on virtual models that were mounted at the occlusal vertical dimension, and were made using CAD/CAM technology. DISCUSSION: Unlike conventional impression techniques, intraoral scanning is not able to be performed while the tissue is moving. This case report used a scan retractor that facilitated stretching and fixation of the vestibular area. It also helped to retract the lips and cheeks. This report also demonstrates that virtual models at OVD can be obtained without the use of conventional stone models, flasking or processing techniques. One of the main shortcomings in the existing CAD/CAM denture fabrication technology is that it is not able to produce customized denture teeth. The present article demonstrates that the digital denture fabrication workflow can provide customized denture teeth to optimize occlusion. CONCLUSION: This case demonstrated how digital complete dentures can be made without requiring conventional stone models or mounting the models in an articulator.

[Association Between SNP rs6007897 of CELSR1 and Acute Ischemic Stroke in Western China Han Population: a Case-control Study].

OBJECTIVE: To investigate the relationship between single nucleotide polymorphism (SNP) rs6007897 of CELSR1 and acute ischemic stroke in Western China Han population. METHODS: All subjects (759 acute ischemic stroke patients and 786 controls) were genotyped using ligation detection reaction (LDR). We analyzed the differences between SNP rs6007897 genotypes and allele frequencies between two groups. RESULTS: Two genotypes (AA, AG) of rs6007897 were found in both stroke and control group. There was no statistically significance between two groups about genotype and allele frequency. After adjusting for risk factors, we found there was no significant association between rs6007897 and ischemic stroke CP = 0.797, odds ratio (OR) = 0.886, 95% confidence interval (CI) = 0.352-2.227). CONCLUSION: SNP rs6007897 of CELSR1 was not significantly associated with ischemic stroke in Western China Han population.