Investigation of polypyrrole based composite material for lithium sulfur batteries.

With the rising demand for electricity storage devices, the performance requirements for such equipment have become increasingly stringent. Lithium-sulfur (Li-S) batteries are poised to be among the next generation of energy storage systems. However, before they can be commercially viable, several challenges must be addressed, including low sulfur conductivity and the shuttle effect. Herein, polypyrrole based sulfur composite was prepared by simple method in hydrothermal teflon lined autoclave for Li-S battery. The S/SP/ppy/PVDF electrode exhibited the initial discharge capacity of 662 mAh g- 1 at 0.5 C and 637 mAh g- 1 after 100 cycles. The Coulombic efficiency was 96% all along charge/discharge cycling. Moreover, Li-S coin cells were assembled and tested to demonstrate the potential application and scale-up of the polypyrrole-sulfur composite.

Insight into the Li-Storage Property of Surface-Modified Ti2Nb10O29 Anode Material for High-Rate Application.

Ti-based anode materials are considered to be an alternative to graphite anodes to accomplish high-rate application requirements. Ti2Nb10O29 (TNO15) has attracted much attention due to its high lithium storage capacity through the utilization of multiple redox couples and a suitable operating voltage window of 1.0 to 2.0 V vs Li/Li+. However, poor intrinsic electronic conductivity has limited the futuristic applicability of this material to the battery anode. In this work, we report the modification of TNO15 by introducing oxygen vacancies and using few-layered carbon and copper coatings on the surface to improve its Li+ storage property. With the support of the galvanostatic intermittent titration technique (GITT), we found that the diffusion coefficient of carbon/copper coated TNO15 is 2 orders of magnitude higher than that of the uncoated sample. Here, highly conductive copper metal on the surface of the carbon-coated oxygen-vacancy-incorporated TNO15 increases the overall electronic and ionic conductivity. The prepared TNO15-800-C-Cu-700 half-cell shows a significant rate capability of 92% when there is a 10-fold increase in the current density. In addition, the interconnected TNO15 nanoparticles create a porous microsphere structure, which enables better Li-ion transportation during charge/discharge process, and experiences an enhancement after the carbon and copper coating on the surface of the primary TNO15 nanocrystallites.

Electrochemical performance of composite electrodes based on rGO, Mn/Cu metal-organic frameworks, and PANI.

Benzendicarboxylic acid (BDC)-based metal-organic frameworks (MOFs) have been widely utilized in various applications, including supercapacitor electrode materials. Manganese and copper have solid diamond frames formed with BDC linkers among transition metals chosen for MOF formation. They have shown the possibility to enlarge capacitance at different combinations of MOFs and polyaniline (PANI). Herein, reduced graphene oxide (rGO) was used as the matrix to fabricate electrochemical double-layer SCs. PANI and Mn/Cu-MOF's effect on the properties of electrode materials was investigated through electrochemical analysis. As a result, the highest specific capacitance of about 276 F/g at a current density of 0.5 A/g was obtained for rGO/Cu-MOF@PANI composite.

Nanoparticle-Based Rifampicin Delivery System Development.

The alkaline milieu of chronic wounds severely impairs the therapeutic effect of antibiotics, such as rifampicin; as such, the development of new drugs, or the smart delivery of existing drugs, is required. Herein, two innovative polyelectrolyte nanoparticles (PENs), composed of an amphiphilic chitosan core and a polycationic shell, were synthesized at alkaline pH, and in vitro performances were assessed by 1H NMR, elemental analysis, FT-IR, XRD, DSC, DLS, SEM, TEM, UV/Vis spectrophotometry, and HPLC. According to the results, the nanostructures exhibited different morphologies but similar physicochemical properties and release profiles. It was also hypothesized that the simultaneous use of the nanosystem and an antioxidant could be therapeutically beneficial. Therefore, the simultaneous effects of ascorbic acid and PENs were evaluated on the release profile and degradation of rifampicin, in which the results confirmed their synergistic protective effect at pH 8.5, as opposed to pH 7.4. Overall, this study highlighted the benefits of nanoparticulate development in the presence of antioxidants, at alkaline pH, as an efficient approach for decreasing rifampicin degradation.

Polylactide/Polyvinylalcohol-Based Porous Bioscaffold Loaded with Gentamicin for Wound Dressing Applications.

This study explores the feasibility of modifying the surface liquid spraying method to prepare porous bioscaffolds intended for wound dressing applications. For this purpose, gentamicin sulfate was loaded into polylactide-polyvinyl alcohol bioscaffolds as a highly soluble (hygroscopic) model drug for in vitro release study. Moreover, the influence of inorganic salts including NaCl (10 g/L) and KMnO4 (0.4 mg/L), and post-thermal treatment (T) (80 °C for 2 min) on the properties of the bioscaffolds were studied. The bioscaffolds were characterized by scanning electron microscopy, Fourier Transform infrared spectroscopy, and differential scanning calorimetry. In addition, other properties including porosity, swelling degree, water vapor transmission rate, entrapment efficiency, and the release of gentamicin sulfate were investigated. Results showed that high concentrations of NaCl (10 g/L) in the aqueous phase led to an increase of around 68% in the initial burst release due to the increase in porosity. In fact, porosity increased from 68.1 ± 1.2 to 94.1 ± 1.5. Moreover, the thermal treatment of the Polylactide-polyvinyl alcohol/NaCl (PLA-PVA/NaCl) bioscaffolds above glass transition temperature (Tg) reduced the initial burst release by approximately 11% and prolonged the release of the drug. These results suggest that thermal treatment of polymer above Tg can be an efficient approach for a sustained release.

Stabilization of chitosan-based polyelectrolyte nanoparticle cargo delivery biomaterials by a multiple ionic cross-linking strategy.

PolyElectrolyte Nanoparticles (PENs) obtained by layer-by-layer self-assembly of polycations/polyanions suffer from a lack of colloidal stability in physiological conditions. We report a simple innovative approach for increasing their stability by multiple ionic cross-linkers. Herein, a chitosan-based core was stabilized by polyanions such as tripolyphosphate and dextran sulfate at pHs of 3 (aPENs) and 8 (bPENs) to improve the quality of electrostatic interactions in the core and manage self-assembly of polyethyleneimine shell onto the core. The physicochemical properties of the particles were characterized by DLS, SEM, TEM, FT-IR, and TGA. TEM micrographs showed visible core/shell structures of bPENs. From particle size and polydispersity indices, the bPENs stability was salt concentration-dependent. The release profiles of PENs using nicotinic acid demonstrated sustained release in a pH-independent manner with a good fit of Korsmeyer-Peppas model. These results suggest that multiple ionic cross-linkers can be an efficient approach to increase the colloidal stability of PENs.

A Highly Flexible Supercapacitor Based on MnO2/RGO Nanosheets and Bacterial Cellulose-Filled Gel Electrolyte.

The flexible supercapacitors (SCs) of the conventional sandwich-type structure have poor flexibility due to the large thickness of the final entire device. Herein, we have fabricated a highly flexible asymmetric SC using manganese dioxide (MnO2) and reduced graphene oxide (RGO) nanosheet-piled hydrogel films and a novel bacterial cellulose (BC)-filled polyacrylic acid sodium salt-Na2SO4 (BC/PAAS-Na2SO4) neutral gel electrolyte. Apart from being environmentally friendly, this BC/PAAS-Na2SO4 gel electrolyte has high viscosity and a sticky property, which enables it to combine two electrodes together. Meanwhile, the intertangling of the filled BC in the gel electrolyte hinders the decrease of the viscosity with temperature, and forms a separator to prevent the two electrodes from short-circuiting. Using these materials, the total thickness of the fabricated device does not exceed 120 µm. This SC device demonstrates high flexibility, where bending and even rolling have no obvious effect on the electrochemical performance. In addition, owing to the asymmetric configuration, the cell voltage of this flexible SC has been extended to 1.8 V, and the energy density can reach up to 11.7 Wh kg-1 at the power density of 441 W kg-1. This SC also exhibits a good cycling stability, with a capacitance retention of 85.5% over 5000 cycles.