Practical implementation of robust MR-thermometry during clinical MR-guided microwave ablations in the liver at 1.5 T.

Practical non-invasive equipment modifications and effective acquisition methods to achieve robust and reliable real-time MR thermometry for monitoring of clinical hepatic microwave ablations were implemented. These included selection of the microwave generator location (inside versus outside the MR scan room), the number of radiofrequency chokes added to the microwave generator's coaxial lines, and the use of copper wool to maximize their electrical grounding. Signal-to-noise ratio (SNR) of MR thermometry images of a small fluid-filled phantom acquired during activation of microwave antenna were used to evaluate image quality as a function of each modification. SNR measurements corresponding to both locations of the microwave generator were comparable and so it was located outside the MR scan room. For this location, addition of one RF choke on the power and four chokes on the sensor coaxial lines was found to be optimal, corresponding to a 68% increase in SNR. Furthermore, image quality strongly depended on the proper electrical grounding of the power and sensor lines. SNR ratio (relative to SNR of baseline images) during activation of microwave generator was found to be 0.49 ±â€¯0.28 without adequate grounding, and 0.88 ±â€¯0.08 with adequate grounding (p = 0.002, Student's t-test). These SNR measurements were sufficiently sensitive to detect issues related to equipment performance and hence formed part of the quality assurance testing performed prior to each clinical treatment. Incorporating these non-invasive approaches resulted in significant improvements to image quality and, importantly while maintaining the clinical integrity of the microwave system which is of paramount importance in a highly regulated healthcare environment.

Cartilage T1ρ and T2 relaxation times: longitudinal reproducibility and variations using different coils, MR systems and sites.

OBJECTIVE: To evaluate the longitudinal reproducibility and variations of cartilage T1ρ and T2 measurements using different coils, MR systems and sites. METHODS: Single-Site study: Phantom data were collected monthly for up to 29 months on four GE 3T MR systems. Data from phantoms and human subjects were collected on two MR systems using the same model of coil; and were collected on one MR system using two models of coils. Multi-site study: Three participating sites used the same model of MR systems and coils, and identical imaging protocols. Phantom data were collected monthly. Human subjects were scanned and rescanned on the same day at each site. Two traveling human subjects were scanned at all three sites. RESULTS: Single-Site Study: The phantom longitudinal RMS-CVs ranged from 1.8% to 2.7% for T1ρ and 1.8-2.8% for T2. Significant differences were found in T1ρ and T2 values using different MR systems and coils. Multi-Site Study: The phantom longitudinal RMS-CVs ranged from 1.3% to 2.6% for T1ρ and 1.2-2.7% for T2. Across three sites (n = 16), the in vivo scan-rescan RMS-CV was 3.1% and 4.0% for T1ρ and T2, respectively. Phantom T1ρ and T2 values were significantly different between three sites but highly correlated (R > 0.99). No significant difference was found in T1ρ and T2 values of traveling controls, with cross-site RMS-CV as 4.9% and 4.4% for T1ρ and T2, respectively. CONCLUSION: With careful quality control and cross-calibration, quantitative MRI can be readily applied in multi-site studies and clinical trials for evaluating cartilage degeneration.

An investigation of the effects from a urethral warming system on temperature distributions during cryoablation treatment of the prostate: a phantom study.

Introduction of urethral warmers to aid cryosurgery in the prostate has significantly reduced the incidence of urethral sloughing; however, the incidence rate still remains as high as 15%. Furthermore, urethral warmers have been associated with an increase of cancer recurrence rates. Here, we report results from our phantom-based investigation to determine the impact of a urethral warmer on temperature distributions around cryoneedles during cryosurgery. Cryoablation treatments were simulated in a tissue mimicking phantom containing a urethral warming catheter. Four different configurations of cryoneedles relative to urethral warming catheter were investigated. For each configuration, the freeze-thaw cycles were repeated with and without the urethral warming system activated. Temperature histories were recorded at various pre-arranged positions relative to the cryoneedles and urethral warming catheter. In all configurations, the urethral warming system was effective at maintaining sub-lethal temperatures at the simulated surface of the urethra. The warmer action, however, was additionally demonstrated to potentially negatively impact treatment lethality in the target zone by elevating minimal temperatures to sub-lethal levels. In all needle configurations, rates of freezing and thawing were not significantly affected by the use of the urethral warmer. The results indicate that the urethral warming system can protect urethral tissue during cryoablation therapy with cryoneedles placed as close as 5mm to the surface of the urethra. Using a urethral warming system and placing multiple cryoneedles within 1cm of each other delivers lethal cooling at least 5mm from the urethral surface while sparing urethral tissue.

Evaluation of mineral oil as an acoustic coupling medium in clinical MRgFUS.

We empirically evaluate mineral oil as an alternative to the mixture of de-gassed water and ultrasound gel, which is currently used as an acoustic coupling medium in clinical magnetic resonance guided focused ultrasound (MRgFUS) treatments. The tests were performed on an ExAblate 2000 MRgFUS system (InSightec Inc., Haifa, Israel) using a clinical patient set-up. Acoustic reflections, treatment temperatures, sonication spot dimensions and position with respect to target location were measured, using both coupling media, in repeated sonications in a tissue mimicking gel phantom. In comparison with the water-gel mix, strengths of acoustic reflections from coupling layers prepared with mineral oil were on average 39% lower and the difference was found to be statistically significant (p = 3.3 x 10(-8)). The treatment temperatures were found to be statistically equivalent for both coupling media, although temperatures corresponding to mineral oil tended to be somewhat higher (on average 1.9 degrees C) and their standard deviations were reduced by about 1 degrees C. Measurements of sonication spot dimensions and positions with respect to target location did not reveal systematic differences. We conclude that mineral oil may be used as an effective non-evaporating acoustic coupling medium for clinical MRgFUS treatments.

MR guided focused ultrasound: technical acceptance measures for a clinical system.

Magnetic resonance (MR) guided focused ultrasound (MRgFUS) is a hybrid technique which offers efficient and safe focused ultrasound (FUS) treatments of uterine fibroids under MR guidance and monitoring. As a therapy device, MRgFUS requires systematic testing over a wide range of operational parameters prior to use in the clinical environment. We present technical acceptance tests and data for the first clinical MRgFUS system, ExAblate 2000 (InSightec Inc., Haifa, Israel), that has been FDA approved for treating uterine fibroids. These tests characterize MRgFUS by employing MR temperature measurements in tissue mimicking phantoms. The coronal scan plane is empirically demonstrated to be most reliable for measuring temperature elevations resulting from high intensity ultrasound (US) pulses ('sonications') and shows high sensitivity to changes in sonication parameters. Temperatures measured in the coronal plane were used as a measure of US energy deposited within the focal spot for a range of sonication parameters used in clinical treatments: spot type, spot length, output power, sonication duration, US frequency, and depth of sonication. In addition, MR images acquired during sonications were used to measure effective diameters and lengths of available sonication spot types and lengths. At a constant 60 W output power, the effective spot type diameters were measured to vary between 4.7 +/- 0.3 mm and 6.6 +/- 0.4 mm; treatment temperatures were found to decrease with increasing spot diameter. Prescribing different spot lengths was found to have no effect on the measured length or on measured temperatures. Tests of MRgFUS positioning accuracy determined errors in the direction parallel to the propagation of the US beam to be significantly greater than those in the perpendicular direction; most sonication spots were erroneously positioned towards the FUS transducer. The tests reported here have been demonstrated to be sufficiently sensitive to detect water leakage inside the FUS transducer. The data presented could be used for comparison by those conducting acceptance tests on other clinical MRgFUS systems.

MRI as a biomarker of disease progression in a therapeutic trial of milameline for AD.

OBJECTIVE: To assess the feasibility of using MRI measurements as a surrogate endpoint for disease progression in a therapeutic trial for AD. METHODS: A total of 362 patients with probable AD from 38 different centers participated in the MRI portion of a 52-week randomized placebo-controlled trial of milameline, a muscarinic receptor agonist. The therapeutic trial itself was not completed due to projected lack of efficacy on interim analysis; however, the MRI arm of the study was continued. Of the 362 subjects who underwent a baseline MRI study, 192 subjects underwent a second MRI 1 year later. Hippocampal volume and temporal horn volume were measured from the MRI scans. RESULTS: The annualized percent changes in hippocampal volume (-4.9%) and temporal horn volume (16.1%) in the study patients were consistent with data from prior single-site studies. Correlations between the rate of MRI volumetric change and change in behavioral/cognitive measures were greater for the temporal horn than for the hippocampus. Decline over time was more consistently seen with imaging measures, 99% of the time for the hippocampus, than behavioral/cognitive measures (p < 0.001). Greater consistency in MRI than behavioral/clinical measures resulted in markedly lower estimated sample size requirements for clinical trials. The estimated number of subjects per arm required to detect a 50% reduction in the rate of decline over 1 year are: AD Assessment Scale-cognitive subscale 320; Mini-Mental Status Examination 241; hippocampal volume 21; temporal horn volume 54. CONCLUSION: The consistency of MRI measurements obtained across sites, and the consistency between the multisite milameline data and that obtained in prior single-site studies, demonstrate the technical feasibility of using structural MRI measures as a surrogate endpoint of disease progression in therapeutic trials. However, validation of imaging as a biomarker of therapeutic efficacy in AD awaits a positive trial.

Magnetic resonance elastography: non-invasive mapping of tissue elasticity.

Magnetic resonance elastography (MRE) is a phase-contrast-based MRI imaging technique that can directly visualize and quantitatively measure propagating acoustic strain waves in tissue-like materials subjected to harmonic mechanical excitation. The data acquired allows the calculation of local quantitative values of shear modulus and the generation of images that depict tissue elasticity or stiffness. This is significant because palpation, a physical examination that assesses the stiffness of tissue, can be an effective method of detecting tumors, but is restricted to parts of the body that are accessible to the physician's hand. MRE shows promise as a potential technique for 'palpation by imaging', with possible applications in tumor detection (particularly in breast, liver, kidney and prostate), characterization of disease, and assessment of rehabilitation (particularly in muscle). We describe MRE in the context of other recent techniques for imaging elasticity, discuss the processing algorithms for elasticity reconstruction and the issues and assumptions they involve, and present recent ex vivo and in vivo results.

High-resolution intracranial and cervical MRA at 3.0T: technical considerations and initial experience.

Initial experience with intracranial and cervical MRA at 3.0T is reported. Phantom measurements (corrected for relaxation effects) show S/N (3.0T) = 2.14 +/- 0.08 x S/N (1.5T) in identical-geometry head coils. A 3.0T 3DTOF intracranial imaging protocol with higher-order autoshimming was developed and compared to 1.5T 3DTOF in 12 patients with aneurysms. A comparison by two radiologists showed the 3.0T to be significantly better (P < 0.001) for visualization of the aneurysms. The feasibility of cervical and intracranial contrast enhanced MR angiography (CEMRA) at 3.0T is also examined. The relaxivity of the gadolinium contrast agent decreases by only about 4-7% when the field strength is increased from 1.5 to 3.0T. Cervical 3.0T CEMRA was obtained in eight patients, two of whom had 1.5T studies available for direct comparison. Image comparison suggests 3.0T to be a favorable field strength for cervical CEMRA. Voxel volumes of 0.62-0.73 mm(3) (not including zero-filling) were readily achieved at 3.0T with the use of a single-channel transmit-receive head or cervical coil, a 25 mL bolus of gadoteridol, and a 3D pulse sequence with a 66% sampling efficiency. This spatial resolution allowed visualization of intracranial aneurysms, carotid dissections, and atherosclerotic disease including ulcerations. Potential drawbacks of 3.0T MRA are increased SAR and T(*)(2) dephasing compared to 1.5T. Image comparison suggests signal loss due to T(*)(2) dephasing will not be substantially more problematic than at 1.5T. The dependence of RF power deposition on TR for CEMRA is calculated and discussed.

Autocorrection of three-dimensional time-of-flight MR angiography of the Circle of Willis.

OBJECTIVE: The purpose of this study was to investigate the efficacy of a retrospective adaptive motion correction technique known as autocorrection for reducing motion-induced artifacts in high-resolution three-dimensional time-of-flight MR angiography of the circle of Willis. MATERIALS AND METHODS: Ten consecutive volunteers were imaged with an unenhanced gradient-recalled echo three-dimensional time-of-flight MR angiography sequence of the circle of Willis. Each volunteer was asked to rotate approximately 2 degrees after completion of one third and one half of the acquisition in the axial, sagittal, and oblique planes (45 degrees to the axial and sagittal planes). A single static data set was also acquired for each volunteer. Unprocessed and autocorrected maximum-intensity-projection images were reviewed as blinded image pairs by six radiologists and were compared on a five-point image quality scale. RESULTS: Mean improvement in image quality after autocorrection was 1.4 (p < 0.0001), 1.1 (p < 0.0001), and 0.2 (p = 0.003) observer points (maximum value, 2.0), respectively, for examinations corrupted by motion in the axial, oblique, and sagittal planes. All three axes had statistically significant improvement in image quality compared with the uncorrected images. Changes in image quality after the application of the autocorrection algorithm to static angiogram data were not statistically significant (mean change in score = -0.13 points; p = 0.29). CONCLUSION: Autocorrection can reduce artifacts in motion-corrupted MR angiography of the circle of Willis without distorting motion-free examinations.

Assessment of thermal tissue ablation with MR elastography.

An important part of thermal ablation therapy is the assessment of the spatial extent of tissue coagulation. In this work, the mechanical properties of thermally-ablated tissue were quantitatively evaluated using magnetic resonance elastography (MRE). This study shows that the mechanical properties of focused ultrasound ablated tissue are significantly different from normal tissue, and the difference can be imaged and measured using MRE. Repeated experiments revealed a reproducible pattern of tissue mechanical property change during thermal ablation in ex vivo bovine muscle. This pattern may reflect changes in intrinsic tissue structure and could be used to evaluate tissue coagulation during thermal ablation therapy. Magn Reson Med 45:80-87, 2001.

Simultaneous image acquisition utilizing hybrid body and phased array receiver coils.

In clinical MR imaging the design and selection of receiver coil is an important step in ensuring the highest image quality. Often this choice is based on selecting a receiver coil characterized by high spatial uniformity such as the body and head volume receiver coils or a surface coil (or array of coils) that provide high signal-to-noise ratio (SNR). In the past, it has been difficult to accomplish both high SNR and spatial uniformity as both coil types achieve one of these characteristics at the expense of the other. The purpose of this study was to achieve both high SNR and spatial uniformity through the simultaneous acquisition of the MR signal using the body and a surface coil array. Results indicate that this hybrid system can provide uniformity and SNR values comparable to those achieved by the body and surface coil arrays, respectively.

Autocorrection in MR imaging: adaptive motion correction without navigator echoes.

A technique for automatic retrospective correction of motion artifacts on magnetic resonance (MR) images was developed that uses only the raw (complex) data from the MR imager and requires no knowledge of patient motion during the acquisition. The algorithm was tested on coronal images of the rotator cuff in a series of 144 patients, and the improvements in image quality were similar to those achieved with navigator echoes. The results demonstrate that autocorrection can significantly reduce motion artifacts in a technically demanding MR imaging application.

Determination of appropriate RF blocking impedance for MRI surface coils and arrays.

Surface and phased array receiving coils in MRI typically require that RF excitation be accomplished using the body coil. This process requires that the receiving coils contain blocking circuitry to increase the overall circuit impedance during RF excitation and withstand the electromotive force induced by the applied electromagnetic field. The aim of this study was to determine the optimal impedance range required during RF excitation based on an assessment of image quality. The experimental results are fit by an exponential model and establish criteria that can be applied for general receiver coil design.

Rapid autocorrection using prescan navigator echoes.

Autocorrection is an adaptive motion correction algorithm that does not require an in vivo measurement of the motion record. A novel method for ensuring convergence of this algorithm when motion is severe is presented. A limited number of navigator echoes are acquired before the imaging sequence to obtain a "snapshot" of the object. Phase differences between the navigator and image k-space data are used as an estimate of motion-induced phase shifts in the image, followed by autocorrection. In phantom data a six-fold reduction in computation time compared to autocorrection alone was realized. These results indicate that this navigator/autocorrection combination may be useful for reducing motion artifacts and computation time for MR exams when motion along the image phase encoding axis is severe.

Image metric-based correction (autocorrection) of motion effects: analysis of image metrics.

Magnetic resonance (MR) imaging of the shoulder necessitates high spatial and contrast resolution resulting in long acquisition times, predisposing these images to degradation due to motion. Autocorrection is a new motion correction algorithm that attempts to deduce motion during imaging by calculating a metric that reflects image quality and searching for motion values that optimize this metric. The purpose of this work is to report on the evaluation of 24 metrics for use in autocorrection of MR images of the rotator cuff. Raw data from 164 clinical coronal rotator cuff exams acquired with interleaved navigator echoes were used. Four observers then scored the original and corrected images based on the presence of any motion-induced artifacts. Changes in metric values before and after navigator-based adaptive motion correction were correlated with changes in observer score using a least-squares linear regression model. Based on this analysis, the metric that exhibited the strongest relationship with observer ratings of MR shoulder images was the entropy of the one-dimensional gradient along the phase-encoding direction. We speculate (and show preliminary evidence) that this metric will be useful not only for autocorrection of shoulder MR images but also for autocorrection of other MR exams.

Prospective multiaxial motion correction for fMRI.

Corruption of the image time series due to interimage head motion limits the clinical utility of functional MRI. This paper presents a method for real-time prospective correction of rotation and translation in all six degrees of rigid body motion. By incorporating an orbital navigator (ONAV) echo for each of the sagittal, axial, and coronal planes into the fMRI pulse sequence, rotation and translation can be measured and the spatial orientation of the image acquisition sequence that follows can be corrected prospectively in as little as 160 msec. Testing of the method using a computerized motion phantom capable of performing complex multiaxial motion showed subdegree rotational and submillimeter translational accuracy over a range of +/-8 degrees and +/-8 mm of motion. In vivo images demonstrate correction of simultaneous through-plane and in-plane motion and improved detection of fMRI activation in the presence of head motion.

Reliability of water proton chemical shift temperature calibration for focused ultrasound ablation therapy.

Our purpose in this work was to assess the reliability of the calibration coefficient for magnetic resonance water proton chemical shift temperature mapping. Over a six month period, the calibration coefficient was measured 15 times in several different phantoms. A highly linear relationship between water proton chemical shift and temperature change was found. The average temperature calibration coefficient determined from all studies was 0.009+/-0.001 ppm/degrees C. Four of the 15 studies were conducted on the same day using the same phantom. The average temperature calibration coefficient of these four studies was 0.0096+/-0.0001 ppm/degrees C.

MR imaging of shear waves generated by focused ultrasound.

This study has shown that magnetic resonance elastography (MRE) can detect shear waves excited by focused ultrasound (FUS) in both gel phantoms and ex vivo muscle. Good agreement was shown between the shear modulus measured from MRE images generated using FUS and that using previously reported MRE techniques. The shear wave displacement amplitude at the FUS focus was studied and found to be proportional with both FUS ultrasonic pulse intensity and the FUS modulation pulse period over the range tested.

Optimization of a contrast-detail-based method for electronic image display quality evaluation.

The authors previously reported a general technique based on contrast-detail methods to provide an overall quantitative evaluation of electronic image display quality. The figure-of-merit reflecting overall display quality is called maximum threshold contrast or MTC. In this work we have optimized the MTC technique through improvements in both the test images and the figure-of-merit computation. The test images were altered to match the average luminance with that observed for clinical computed radiographic images. The figure-of-merit calculation was altered to allow for contrast-detail data with slopes not equal to -1. Preliminary experiments also were conducted to demonstrate the response of the MTC measurements to increased noise in the displayed image. MTC measurements were obtained from five observers using the improved test images displayed with maximum monitor luminance settings of 30-, 50-, and 70-ft-Lamberts. Similar measurements were obtained from two observers using test images altered by the addition of a low level of image noise. The noise-free MTC and MTC difference measurements exhibited standard deviations of 0.77 and 1.55, respectively. This indicates good measurement precision, comparable or superior to that observed using the earlier MTC technique. No statistically significant image quality differences versus maximum monitor luminance were seen. The noise-added MTC measurements were greater than the noise-free values by an average of 4.08 pixel values, and this difference was statistically significant. This response is qualitatively correct, and is judged to indicate good sensitivity of the MTC measurement to increased noise levels.

MR-guided focused-ultrasound ablation system: determination of precision and accuracy in preparation for clinical trials.

The authors analyzed the accuracy and precision of focal-spot placement with a magnetic resonance-guided, focused-ultrasound system. Average absolute accuracy errors ranged from 0.2 to 1.0 mm, and average absolute individual precision errors ranged from 0.2 to 0.3 mm. To prevent damage to vital structures, single sonications and sonication grids should be placed beyond approximately 2 and 1 mm, respectively.