Wheelchair users' perceived exertion during typical mobility activities.

STUDY DESIGN: Each participant performed a series of wheelchair exercises equivalent in intensity to minimal functional speed (1 m s(-1)), functional walking speed (1.3 m s(-1)), a relatively challenging speed (1.6 m s(-1)) and a self-selected speed. Each participant also completed a graded exercise test (GXT) to volitional exhaustion (VO2peak). OBJECTIVES: The purpose of this study was (1) to assess the physical capacity of wheelchair users as they undertake typical mobility activities and (2) to investigate how closely the components of a differentiated model of perceived exertion mirror wheelchair users' own perception of exertion. METHODS: Eleven (eight males and three females) spinal cord-injured or congenitally impaired wheelchair-dependent participants volunteered for the study. Differentiated ratings of perceived exertion (RPE_arm and RPE_respiration) and oxygen uptake (VO2) and heart rate were recorded during each exercise. RESULTS: The mean comfortable speed at which the participants propelled their own wheelchairs on the wheelchair ergometer was 1.1±0.2 m s(-1). Speeds of 1 m s(-1) and 1.3 m s(-1) are typical of everyday functional propulsion. The corresponding RPE_respiration and RPE_arm ranged from 7 to 13 on the Borg scale; the %VO2peak measured in these trials ranged from 37 to 80% VO2peak. For propulsion intensities used in the present study-low, moderate, high and graded exercise intensity-no difference could be observed between RPE_respiration and RPE_arm. There were no significant differences between RPE_arm and RPE_respiration at the termination of the GXT. CONCLUSION: The current study showed potential for the use of RPE to assess and monitor daily wheelchair propulsion intensity in individuals with paraplegia.

Technology for mobility in SCI 10 years from now.

OBJECTIVES: To identify technological advances and that are likely to have a great impact on the quality of life and participation in individuals with spinal cord injury (SCI). METHODS: In this paper we use the International Classification of Function to frame a discussion on how technology is likely to impact SCI in 10 years. In addition, we discuss the implication of technological advances on future research. RESULTS/CONCLUSION: Although technology advances are exciting, a large challenge for the research community will be how to effectively apply and deploy this technology. Advances occurring in the next 10 years that reduce cost of technology may be more important to the population with SCI than brand new technologies. Social context is everything. As a research community we must advocate for better systems of care. Advocating now for better care will lead to a world in 2020 that is ready to adopt new technologies that are truly transformative.

Changes in the structural and material properties of the tibia in patients with spinal cord injury.

STUDY DESIGN: A cross-sectional study. OBJECTIVES: To measure the change of structural and material properties at different sites of the tibia in spinal cord-injured patients using peripheral quantitative computerised tomography (pQCT). SETTING: Orthopaedic research centre (UK). METHODS: Thirty-one subjects were measured--eight with acute spinal cord injury (SCI), nine with chronic SCI and fourteen able-bodied controls. pQCT scans were performed at 2% (proximal), 34% (diaphyseal) and 96% (distal) along the tibia from the tibial plateau. Structural measures of bone were calculated, and volumetric bone mineral density (vBMD) was also measured at all three levels. Muscle cross-sectional area was measured at the diaphyseal level. RESULTS: Structurally, there were changes in the cortical bone; in the diaphysis, the shape of the cross-section changed to offer less resistance to AP bending, and the cross-sectional area of the cortical shell decreased both proximally and distally. There were corresponding changes in vBMD in the anterior aspect of the cortical diaphysis, as well as proximal and distal trabecular bone. Changes in muscle occurred more rapidly than changes in bone. CONCLUSION: There were clear changes of both structure and material at all three levels of the tibia in chronic SCI patients. These changes were consistent with specific adaptations to reduced local mechanical loading conditions. To assess fracture risk in SCI and also to monitor the effect of therapeutic interventions, the structure of the bone should be considered in addition to trabecular bone mineral density.

Early treatment with zoledronic acid prevents bone loss at the hip following acute spinal cord injury.

UNLABELLED: Osteoporosis after spinal cord injury is common. Reductions in bone density are rapid and fracture rates are higher after injury. Early treatment with 4 mg zoledronic acid significantly reduced bone loss at the hip compared to untreated individuals in the first year. Treatment appeared safe and well tolerated. INTRODUCTION: Bone mineral density (BMD) is lost rapidly following spinal cord injury (SCI), predominantly in the lower limbs. Bone turnover markers suggest an early increase in resorption. METHODS: A randomised, open-label study of 14 patients with acute SCI randomised to receive 4 mg IV zoledronic acid or standard treatment. BMD was measured by dual-X-ray absorptiometry at the lumbar spine and hip (femoral neck, total and trochanter) at baseline, 3, 6 and 12 months. Bone turnover markers (serum C-terminal telopeptide and Procollagen I N-terminal peptide and urinary N-terminal telopeptide/Cr ratio) were also measured. RESULTS: After 12 months, there was a significant difference in BMD between the groups at the total hip (12.4%, p = 0.005), trochanter (13.4%, p = 0.028) and lumbar spine (2.7%, p = 0.033). However, the difference between groups at the femoral neck was not significant (4.8%, p = 0.741). In the treated group, bone resorption was reduced and remained reduced up to 12 months. Other than flu-like symptoms immediately after the infusion, no adverse events were observed. CONCLUSION: IV zoledronic acid is an effective and well-tolerated treatment to prevent bone mineral density loss at the total hip and trochanter for up to 12 months following SCI.

A novel approach to bite force measurements in a porcine model in vivo.

A novel device for a bite force measurement system in a porcine model is described. A single polyethylene layer was vacuum-formed into a splint, and a force sensor was fitted on to the splint occlusal surface and seated with a silicone layer. This design enabled the measurement of bite forces on selected teeth in a large animal model with either natural dentition or single implant crowns and could be used in assessing information on biomechanical adaptation of the bone-implant interface to masticatory loads. Preliminary recordings of force values obtained during mastication in the premolar region (200-560 N) and various limiting factors of the technical design are discussed.

The objective measurement of spinal orthosis use for the treatment of adolescent idiopathic scoliosis.

STUDY DESIGN: Technology development and prospective study. OBJECTIVES: Develop instrumentation for discrete, reliable, and objective measurement of brace use patterns between routine follow-ups and without patient involvement. BACKGROUND DATA: To understand spinal bracing efficacy and clinical effectiveness in the conservative treatment of adolescent idiopathic scoliosis, it is essential to measure and record such confounding variables as spinal physiology, force distribution, and compliance. Historically, compliance was measured using patient interviews, pad/strap forces, or temperature. These measurements were subjective, limited to laboratory or short-term monitoring only, required patient intervention, or lacked date/time recording. METHODS: Custom-fitted nonperforated thoracic lumbar sacral orthoses were instrumented with discrete data loggers to measure and record temperature at the skin-brace interface at 16-minute date/time-stamped intervals for up to 88-day periods without patient involvement. Ten female patients (age 15 years, SD 1.2) with adolescent idiopathic scoliosis who had spinal bracing as part of their treatment regimen took part in the study over 14 months, SD 4.5 months. RESULTS: Compliance with the treatment regimen ranged from 8% to 90%, average 65%. Patients tended to overestimate their compliance by 150% (SD 50%). There was no significant difference between weekday and weekend compliance but wear patterns differed. Night wear was significantly greater than day wear (P < 0.01). Patients with very good compliance only removed their brace for washing or exercise periods, but where poor compliance was evident, the brace was only worn sporadically during the day. CONCLUSIONS: Temperature provides a clear signal of the time in brace and can be used for long-term data logging using discrete instrumentation, providing a tool to help identify and understand the reasons behind poor compliance.

Evaluation of mattresses using interface pressure mapping.

OBJECTIVE: To compare the ranking of mattresses using several different performance indices, calculated from interface pressure-mapping data. METHOD: Five mattresses were compared using interface pressure-mapping on 10 healthy volunteers. Mattresses were ranked in order, on the basis of several different specified performance indices. RESULTS: Different performance indices ranked the mattresses in different orders. CONCLUSION: Elaborate performance indices should be used with care, since it is possible to construct a 'tailor-made' performance index to make any chosen mattress rank as the best. Care should be taken to ensure that a performance index is validated, preferably by some demonstrated link to clinical outcomes.

Quantitative measurement of spinal brace use and compliance in the treatment of adolescent idiopathic scoliosis.

The objective measurement of compliance with spinal bracing in adolescents with idiopathic scoliosis (AIS) is fundamental in the validation of clinical trials of bracing effectiveness, and in helping clinicians better understand reasons behind poor compliance. Current technology has been developed and tested for discrete, reliable and objective measurement of the times of day a brace is worn and consistency in its use. TLSOs were instrumented with data loggers measuring temperature at the skin/brace interface at 16 minutes intervals over a period of 88 days; between routine follow up and without patient interference. 10 female patients (age 14 years, sd 1.1) with AIS using spinal bracing as part of their treatment regime took part in the study over 15 months. Skin/brace interface temperature during periods of wear in the UK was >30 degrees C, ambient 23 degrees C, sd 4. Compliance ranged from 8-90%, average 65%. Patients tended to over estimate their compliance by 150% (sd 50%). There was no significant difference between weekday and weekend compliance but wear patterns differed. Nightwear was significantly greater than daywear. Patients with very good compliance only removed their brace for washing or exercise periods but where poor compliance was evident, the brace was only worn sporadically during the day. Temperature provides a clear signal of brace use and can be used for long-term data logging using discrete instrumentation, providing a tool to help identify and understand the reasons behind poor compliance.

An instrument for in-service testing of mattresses.

It is widely recognised that mattresses have a finite life-span. In particular, hospital mattresses, typically made from polymer foam materials, are known to degrade over a period of years. Fatigue of a mattress in this way leads to a phenomenon known as 'bottoming'. This refers to the yielding of the mattress to such an extent that the occupant comes into close contact with the hard base of the bed: an important condition to avoid as it is thought to represent an aggravated risk factor for pressure ulcers. The authors have developed a portable, easy--to use, interactive device that quickly gives accurate information as to the condition of a mattress in a clinical setting. The device is validated against accelerated fatigue, pressure mapping of bottoming with healthy volunteers, and service life of 150 mattresses. The QUINCE SUPPORT SCORE provides an objective and valid basis for a mattress replacement programme.

Evaluation of a sensor for low interface pressure applications.

An ultra-thin, small sensor has recently been developed, "FlexiForce" (Tekscan, Boston, MA, USA), which may be effective for the measurement of low interface pressure between the skin, support surfaces and pressure garments. To evaluate the suitability of the sensor for these applications, drift, repeatability, linearity, hysteresis and curvature effects were tested under laboratory conditions. The drift was 1.7-2.5%/logarithmic time, the repeatability was 2.3-6.6% and the linearity was 1.9-9.9% in the range of forces of 10-50 g applied. The hysteresis was 5.4% on average. The output offset of the sensor increased with decreasing radius of curvature for radii less than 32 mm compared with a flat surface when no pressure was applied. The sensitivity to pressure decreased with curvature for radii less than 32 mm. It was found that the sensor had acceptable drift, repeatability, linearity and hysteresis. However, a significant curvature effect was observed indicating that the sensor is suitable for direct measurement on surfaces with the radii greater than 32 mm under static conditions.

Fluorescent strip-lights as a source of error in tissue reflectance spectroscopy.

Tissue reflectance spectroscopy is a widely used technique for measuring the blood content of the skin. Fluorescent strip-lighting of a type in widespread use (Osram L36 W/23 Gelbweiss-white) is a potential source of misleading artefacts in tissue reflectance spectroscopy. The fluorescent light signal has successive peaks and troughs in the 520-580 nm range which closely emulate the inverse of the reflected signal of white light modulated by blood. The presence of fluorescent light in the reflected signal cancels some of the blood signature. Conversely, the presence of fluorescent light in the white reference augments the true blood reflected signal. The marked similarity of the resultant artefact blood spectrum to the true blood spectrum is a hazard, as the presence of the artefact may go undetected.

An empirical technique to compensate for melanin when monitoring skin microcirculation using reflectance spectrophotometry.

Errors can occur in measuring blood content and oxygenation in subjects with significant skin pigmentation using reflectance spectrophotometry. The melanin in the epidermis not only reduces the amount of back-scattered light, but also has a characteristic absorption spectrum that varies between individuals. Skin color is primarily influenced by the concentration of melanin, blood content and oxygenation in the superficial microvasculature. A three-step process was developed empirically to accommodate the effect of melanin in the absorption spectrum of skin. A melanin index was developed and applied for each individual tested. Spectral components attributable specifically to melanin were subtracted from the measured spectrum, and its amplitude was normalized. This technique was tested with 26 able-bodied subjects with different levels of skin pigmentation. The melanin-compensated spectra from pigmented and caucasian skin were indistinguishable and no correlation was found between calculated values for indices of blood content and oxygenation, and melanin index.

Assessment of skin blood content and oxygenation in spinal cord injured subjects during reactive hyperemia.

This study was undertaken to determine whether the reactive hyperemia response following ischemia in spinal cord injured (SCI) individuals is different from that which occurs in able-bodied (AB) individuals. The reactive hyperemia response was produced by applying a pressure of 150 mmHg for 300 s, 600 s, and 900 s to the skin over the greater trochanter in 10 SCI and 10 AB subjects using a computer-controlled pneumatic indentation system. The changes in blood content and oxygenation in the superficial vessels of the skin, associated with indentation, were monitored using reflectance spectrophotometry. A brief pressure of 80 mmHg, to simulate finger pressing (blanching), was applied to the same site to detect changes in reflow behavior during the hyperemic period. The results indicate that the reactive hyperemia response in SCI group was not substantially different from AB group although the reflow rate after load release was slower in the SCI group compared with the AB group.

A skin indentation system using a pneumatic bellows.

A pneumatic indentation system using a copper bellows has been developed for physiological studies where a controlled uniaxial compressive force is required to be applied to the surface of the skin. Such a system is useful for studies where the physiological response of the tissues is to be monitored following a known loading history. The indentation system is driven by a vacuum/compression pneumatic pump through solenoid valves under closed-loop computer control. A load cell placed between the indentor and bellows monitors the applied force providing a feedback signal to the computer. The signal from the computer activates the valves supplying air pressure to the bellows, and the applied force is controlled using a digital closed-loop protocol. This system can be used to provide a controlled loading sequence to the skin without utilizing gravitational forces, which allows the subject to keep a more natural position during the experiment.

Relationships between bone structure in the iliac crest and bone structure and strength in the lumbar spine.

The purpose of this study was to examine the relationship between histomorphometric variables of cancellous bone structure and ultimate compressive strength (UCS) in the second lumbar vertebra (L2) and to determine whether structural variables in the iliac crest are predictive of the same variables and of UCS in L2. At autopsy, 7.5 mm diameter cores were removed from the iliac crest and from L2 of 29 subjects who had died suddenly without bone disease. Cancellous bone volume (BV/TV, %) was significantly lower in L2 than in iliac crest due to lower trabecular number (Tb.N, per mm) and thickness (Tb.Th, microns). There were significant correlations between iliac crest and L2 for BV/TV, Tb.N and trabecular separation (Tb.Sp, microns), but not for Tb.Th. BV/TV was negatively correlated, and Tb.Sp was positively correlated with age at both sites. Tb.Th was not significantly correlated with age in the iliac crest, but a significant negative correlation was observed in L2. The UCS of vertebral cores was negatively correlated with age. BV/TV and Tb.Th in L2 were positively correlated with UCS in L2.(ABSTRACT TRUNCATED AT 250 WORDS)

Prototype development and comparative evaluation of wheelchair pressure mapping system.

Wheelchair pressure mapping devices used in the prescription of seat cushions and postural supports have been limited in durability, data presentation, and/or clinical efficiency. This project sought to establish the ideal specifications for clinically useful pressure mapping systems, and to use these specifications to influence the design of an innovative wheelchair pressure mapping system (Tekscan "Seat"). Technology, previously developed for measurement of forces of dental occlusion and of the foot during gait, was applied to wheelchair seat mapping. Tests were designed to compare the performance of three pressure mapping systems: the Tekscan system, the FSA system, and the Talley TPM3. Bench tests were done to measure reproducibility, hysteresis, and creep of each of the pressure mapping systems. A contoured loader gauge was developed to test for the influence of hammocking. Tests were also performed using spinal cord-injured subjects to demonstrate the relative performance of the pressure mapping systems in a clinical setting. A focus group session was conducted with seating specialists to review the strengths and weakness of the systems for routine clinical use. The TPM3 was found to be the most accurate, stable, and reproducible but limited in ease of use, speed, and data presentation. FSA was rated well in clinical application and data management but demonstrated a pronounced hysteresis (+/-19%) and creep (4%). The Tekscan system also showed substantial hysteresis (+/-20%) and creep (19%) but was preferred by clinicians for its real-time display capabilities, resolution, and display options. Some trends in system performance on varied support surfaces were identified and can be a valuable guide to interpretation of measurements and prescription decision making in the clinic. Problems identified with the accuracy and stability of the Tekscan and FSA systems may be amenable to resolution with software correction and changes in fabrication. With these improvements all three systems show the potential to be useful clinical tools.

A new manual method for assessing two-dimensional cancellous bone structure: comparison between iliac crest and lumbar vertebra.

We have developed a simple method for the direct analysis of two-dimensional trabecular structure. Using this method, we have compared the structure of the left and right iliac crest and the second lumbar vertebra and studied the relationship between two-dimensional trabecular structure and the ultimate compressive stress of bone samples from the second lumbar vertebra. Transverse cores were taken from the left and right iliac crests and second lumbar vertebrae of 35 subjects (12 females) who died suddenly. The trabecular structure was subdivided into nodes (node count) and free ends (free end count), which were expressed per square millimeter of cancellous space. A node was defined as the point of junction between two or more trabeculae; a free end was defined as the end of a trabecula that was unconnected in the plane of the section to any other trabecular element. The following struts were defined by drawing a line between the nodes and the free ends: node to node, node to free end, free end to free end, and cortex-derived struts. Strut lengths were measured and expressed as a percentage of the total strut length and per square millimeter of cancellous space. Intraobserver variation was generally low, with coefficients of variation for repeat measurements in the range 3.9-17.8%. There was no statistically significant difference between left and right iliac crests for any of the variables measured. With the exception of cortex-derived struts, there was no statistically significant correlation between crests for any variable.(ABSTRACT TRUNCATED AT 250 WORDS)

Pressure sores: a biochemical test for early detection of tissue damage.

This study was undertaken to seek biochemical indicators in blood associated with the onset of early tissue damage which may progress to the formation of a pressure sore. Changes in serum creatinine phosphokinase (CPK), inorganic phosphate, and lactate dehydrogenase in systemic blood of pigs were investigated before, during, and after local indentation. Pressures of 540mmHg and 700mmHg were applied for six hours on both sides of the scapula and backs of five anesthetized animals. Two hours after release of indentation, serum CPK levels showed marked elevation and remained elevated even after one week. The elevated levels of CPK were shown to correspond to defined pathology of the tissue as determined histologically. On the other hand, inorganic phosphate began to decrease after release of indentation and recovered to the preindentation level after one day. Lactate dehydrogenase did not change significantly throughout the experiment. These results offer important evidence of the potential of CPK as a systemic indicator of muscle damage at an early stage of pressure sore formation.