From Biomass to Fuel Blendstocks via Catalytic Fast Pyrolysis and Hydrotreating: An Evaluation of Carbon Efficiency and Fuel Properties for Three Pathways.

Biomass was upgraded to fuel blendstocks via catalytic fast pyrolysis (CFP) followed by hydrotreating using three approaches: ex situ CFP with a zeolite catalyst (HZSM-5), ex situ CFP with a hydrodeoxygenation catalyst (Pt/TiO2) and cofed hydrogen, and in situ CFP with a low-cost mixed metal oxide catalyst (red mud). Each approach was evaluated using a common pine feedstock and the same hydrotreating procedure. The oxygen contents in the CFP oils ranged from 17 to 28 wt % on a dry basis, and the carbon efficiencies for the CFP processes were in the range of 28-38%. The residual oxygen was reduced to <1 wt % during hydrotreating, which was operated for 104-140 h for each CFP oil without plugging issues. The hydrotreating carbon efficiencies were 81-93%. The CFP pathway with the hydrodeoxygenation catalyst gave the highest overall carbon efficiency from biomass to fuel blendstocks (34%) but, at the same time, also the highest cumulative hydrogen consumption during CFP and hydrotreating. The zeolite pathway produced the largest fraction boiling in the gasoline range and the highest estimated octane number due to the high aromatic content in that CFP oil. The in situ red mud pathway produced the largest fraction of diesel-range products with the highest derived cetane number. However, advances in the CFP and hydrotreating process are required to improve the fuel blendstock properties for all pathways.

Biomass Conversion to Produce Hydrocarbon Liquid Fuel Via Hot-vapor Filtered Fast Pyrolysis and Catalytic Hydrotreating.

Lignocellulosic biomass conversion to produce biofuels has received significant attention because of the quest for a replacement for fossil fuels. Among the various thermochemical and biochemical routes, fast pyrolysis followed by catalytic hydrotreating is considered to be a promising near-term opportunity. This paper reports on experimental methods used 1) at the National Renewable Energy Laboratory (NREL) for fast pyrolysis of lignocellulosic biomass to produce bio-oils in a fluidized-bed reactor and 2) at Pacific Northwest National Laboratory (PNNL) for catalytic hydrotreating of bio-oils in a two-stage, fixed-bed, continuous-flow catalytic reactor. The configurations of the reactor systems, the operating procedures, and the processing and analysis of feedstocks, bio-oils, and biofuels are described in detail in this paper. We also demonstrate hot-vapor filtration during fast pyrolysis to remove fine char particles and inorganic contaminants from bio-oil. Representative results showed successful conversion of biomass feedstocks to fuel-range hydrocarbon biofuels and, specifically, the effect of hot-vapor filtration on bio-oil production and upgrading. The protocols provided in this report could help to generate rigorous and reliable data for biomass pyrolysis and bio-oil hydrotreating research.

Chalcogenide-halides of niobium (V). 1. Gas-phase structures of NbOBr(3), NbSBr(3), and NbSCl(3). 2. Matrix infrared spectra and vibrational force fields of NbOBr(3), NbSBr(3), NbSCl(3), and NbOCl(3).

The molecular structures of NbOBr(3), NbSCl(3), and NbSBr(3) have been determined by gas-phase electron diffraction (GED) at nozzle-tip temperatures of 250 degrees C, taking into account the possible presence of NbOCl(3) as a contaminant in the NbSCl(3) sample and NbOBr(3) in the NbSBr(3) sample. The experimental data are consistent with trigonal-pyramidal molecules having C(3)(v)() symmetry. Infrared spectra of molecules trapped in argon or nitrogen matrices were recorded and exhibit the characteristic fundamental stretching modes for C(3)(v)() species. Well resolved isotopic fine structure ((35)Cl and (37)Cl) was observed for NbSCl(3), and for NbOCl(3) which occurred as an impurity in the NbSCl(3) spectra. Quantum mechanical calculations of the structures and vibrational frequencies of the four YNbX(3) molecules (Y = O, S; X = Cl, Br) were carried out at several levels of theory, most importantly B3LYP DFT with either the Stuttgart RSC ECP or Hay-Wadt (n + 1) ECP VDZ basis set for Nb and the 6-311G basis set for the nonmetal atoms. Theoretical values for the bond lengths are 0.01-0.04 A longer than the experimental ones of type r(a), in accord with general experience, but the bond angles with theoretical minus experimental differences of only 1.0-1.5 degrees are notably accurate. Symmetrized force fields were also calculated. The experimental bond lengths (r(g)/A) and angles ( 90 degree angle (alpha)()/deg) with estimated 2sigma uncertainties from GED are as follows. NbOBr(3): r(Nb=O) = 1.694(7), r(Nb-Br) = 2.429(2), 90 degree angle (O=Nb-Br) = 107.3(5), 90 degree angle (Br-Nb-Br) = 111.5(5). NbSBr(3): r(Nb=S) = 2.134(10), r(Nb-Br) = 2.408(4), 90 degree angle (S=Nb-Br) = 106.6(7), 90 degree angle (Br-Nb-Br) = 112.2(6). NbSCl(3): r(Nb=S) = 2.120(10),r(Nb-Cl) = 2.271(6), 90 degree angle (S=Nb-Cl) = 107.8(12), 90 degree angle (Cl-Nb-Cl) = 111.1(11).