A new strategy to construct MOF-on-MOF derivatives for the removal of tetracycline hydrochloride from water by activation of peroxymonosulfate.

A MOF-on-MOF composite derivative material named ZIF-67@Ce-MOF-600 was designed and synthesized. The preparation of ZIF-67@Ce-MOF-600 was optimized from the aspects of the ratio of metal and ligand, heat-treatment temperature. It was demonstrated by XRD, FT-IR, SEM-EDS and TEM. The optimum conditions for the activation of PMS by ZIF-67@Ce-MOF-600 for the degradation of tetracycline (TC) were investigated by adjusting the catalyst dosage, TC, pH, peoxymonosulfate (PMS) concentration, and different kinds of water, co-existing anions and pollution. Under optimal conditions (20 mg catalysts and 50 mg PMS added) in 100 mL of tetracyclines (TC) solvent (20 mg TC/L), the removal rate could reach up to 99.2% and after five cycles was 70.5%. The EPR results indicated the presence of free radicals and non-free radical, among which free radicals intended to play a major role in the degradation process. Its possible degradation pathways and attack sites were analyzed by liquid-phase mass spectrometry and DFT analysis.

Enhanced adsorption dynamics and thermal stability of radioactive Sr(II) by lamellar Nb-doped sodium vanadosilicate via self-assembly and conditional natroxalate intercalation.

To promote the environmentally friendly and sustainable development of nuclear energy, it is imperative to address the treatment of wastewater generated by the nuclear industry. This necessitates the enhancement of fission product reclamation efficiency post-treatment. This study aims to combine defect control and confined self-assembly strategies for the precise design of interlayer spacing (14.6 Å to 15.1 Å), leading to the fabrication of conditional natroxalate-functionalized vanadosilicate, and its potential application in the efficient adsorption and reclamation of 90Sr. Na0.03Natroxalate2.47Si1.44Nb0.08V1.92O5·1.2 H2O (Nb4-NxSiVO), with a layer spacing of 14.9 Å, exhibits the highest Sr(II) adsorption capacity (248.76 mg/g), enabling effective separation with Cs+. The natroxalate embedded within the confined interlayers demonstrates excellent stability, offering rapid (within 10 min) and stable adsorption sites for Sr(II). Furthermore, Nb4-NxSiVO exhibits a wide band gap and exceptional thermal stability before and after adsorption, rendering hard desorption of 90Sr. The findings highlight the potential of Nb4-NxSiVO as a promising adsorbent for rapid and selective purification of 90Sr-containing wastewater and further application in nuclear batteries.

Study of the Adsorption and Separation Behavior of Scandium and Zirconium by Trialkyl Phosphine Oxide-Modified Resins in Sulfuric and Hydrochloric Acid Media.

Zirconium is recognized as one of the main impurities of the rare earth element scandium during purification. It presents significant challenges due to its similar chemical properties, making separating it difficult. This study used trialkyl phosphine oxide (TRPO) as a functional ligand, and the effects of carrier type and acidity on adsorption performance were first investigated. Among these, the novel extraction resin SiO2-P as a carrier for TRPO demonstrated more prominent separation performance in 0.2 M H2SO4 and 5 M HCl solutions. The kinetic and isotherm data were consistent with the pseudo-secondary kinetics and Langmuir model, respectively, and the adsorption process could be regarded as homogeneous monolayer adsorption subject to the dual effects of chemisorption and internal diffusion. In addition, thermodynamic analysis showed that the adsorption process of zirconium under the experimental conditions was a spontaneous endothermic process. Combined with the results of SEM-EDS, FT-IR, and XPS analyses, scandium and zirconium were successfully adsorbed by the resin and uniformly distributed on its surface, and the greater affinity of the P=O groups on the resin for zirconium was the critical factor contributing to the separation of scandium and zirconium. Finally, scandium and zirconium in sulfuric acid and hydrochloric acid media were extracted and separated by column experiments, and the purity of scandium could reach 99.8% and 99.99%, respectively.

Novel phosphate functionalized sodium alginate hydrogel for efficient adsorption and separation of Nd and Dy from Co.

The recovery of rare earth elements (REEs) including neodymium (Nd) and dysprosium (Dy) from NdFeB permanent magnets has become one of the main ways to solve the increased demand for rare earth. Herein, n-dodecyl phosphate (DPPA) was used for the first time as the adsorption functional group donor, sodium alginate as the substrate, and calcium chloride solution as the reactive solvent, a hybrid hydrogel adsorbent DPPA/CaALG was synthesized by sol-gel method for application in the adsorption and separation of Nd and Dy from the Co-Nd-Dy ternary system. SEM-EDS, and N2 adsorption-desorption analysis showed the successful preparation of DDPA/CaALG with mesoporous structure. Batch experiments showed the superiority of the hybrid hydrogel for the good selective adsorption of Nd and Dy, such as large adsorption capacity (Nd: 162.5 mg/g, Dy: 183.5 mg/g), and no adsorption for Co. FT-IR, XPS showed that PO and P-O groups are involved in the adsorption process of Nd and Dy as electron acceptors, where the ion exchange of P-OH is dominant. Furthermore, the chemical properties of ligands and complexes were analyzed by Density Functional Theory (DFT) calculations and revealed their adsorption behaviors as well as the competition between different metal ions.

Precise recognition and efficient recovery of Pd(II) from high-level liquid waste by a novel aminothiazole-functionalized silica-based adsorbent.

Efficient recognition, separation and recovery of palladium from high-level liquid waste (HLLW) not only helps the safe, green and environmentally friendly disposal of nuclear waste, but also is an essential important supplement to overcome the growing shortage of natural palladium resources. Herein, a novel silica-based functional adsorbent named 2AT-SiAaC was prepared by a two-step method, i.e., grafting of 2-aminothiazole (2AT) via the amidated reaction after in-situ polymerization of acrylic monomers on porous silica. SEM, EDS, TG-DSC, BET and PXRD all proved the successful preparation of 2AT-SiAaC, and it exhibited ultrahigh adsorption selectivity for Pd(II) (Kd (distribution coefficient) ≥ 10,344.2 mL/g, SFPd/M (separation factor) ≥ 613.7), fast adsorption kinetics with short equilibrium time (t ≤ 1 h) and good adsorption capacity (Q ≥ 62.1 mg Pd/g). The dynamic column experiments shows that 2AT-SiAaC achieved efficiently separation of Pd(II) from simulated HLLW, and the enrichment coefficients (C/C0) of Pd(II) was as high as about 14 with the recovery rate nearly 99.9% and basically kept the same performance in three adsorption-desorption column cycle experiments. The adsorption mechanism was analyzed by FT-IR, XPS and DFT calculations, and the ultrahigh selectivity of 2AT-SiAaC was attributed to the preferred affinity of the soft N-donor atoms in 2AT for Pd(II). NO3- ions participated in the adsorption reaction to keep charge balance, and the frontier orbital electron density distribution diagram shows the charge transfer in the process of material preparation and adsorption. To sum up, 2AT-SiAaC adsorbent provided a new insight for precise recognition and efficient separation of Pd(II) from HLLW.

Precise stepwise recovery of platinum group metals from high-level liquid wastes based on SDB polymer-modified SiO2.

Accurate separation and efficient recovery of platinum group metals (PGMs, mainly Ru, Rh and Pd) from high level liquid waste (HLLW) is a good choice for clean production and sustainable development of nuclear energy. Herein a novel SDB polymer modified silica-based amine-functionalized composite (dNbpy/SiO2-P) was synthesized for the separation and recovery of PGMs. Laser particle size analysis and BET results clarified the regular spherical and highly interconnected mesoporous structure of dNbpy/SiO2-P which is critical for the separation of PGMs. The removal percent of PGMs were over 99% on the optimized conditions. In addition, dNbpy/SiO2-P showed excellent selectivity (SFPd/M > 3805, SFRu/M > 1705, SFRh/M > 336) and repeatability (≥5). Interestingly, based on the different adsorption and desorption kinetics of PGMs, a double-column strategy is designed to solve the challenge of separating and recovering PGMs from HLLW. The enrichment factors of Pd(II), Ru(III) and Rh(III) reached 36.7, 8.2, and 1.2. The adsorption of PGMs was coordination mechanism and required the involvement of NO3- to maintain charge balance. The specific distribution of elements within the adsorbents and the changes in valence state were analyzed using depth-profiling XPS. Both depth-profiling XPS results and slope analysis revealed that the complex of dNbpy and PGMs is a 1 : 1 coordination structure. Overall, this work fills the gap that PGMs cannot be effectively separated and enriched from HLLW.

Synthesis and fabrication of segregative and durable MnO2@chitosan composite aerogel beads for uranium(VI) removal from wastewater.

To address the imperative need for efficient removal of uranium-containing wastewater and mitigate radioactive contamination risks associated with nuclear energy, the development of materials with high removal efficiency and facile separation is crucial. This study designed and synthesised MnO2@chitosan (CTS) composite aerogel beads by in-situ growing δ-MnO2 on porous CTS aerogel beads. This approach not only mitigates the agglomeration of MnO2 nanospheres but also significantly enhances the porous structure and surface area of MnO2@CTS. These cost-effective and eco-friendly millimeter-scale spherical aerogels exhibited convenient separation properties after adsorption. These characteristics help mitigate the risk of equipment seam blockage and secondary pollution that are often associated with powdered adsorbents. Additionally, MnO2@CTS exhibited remarkable mechanical strength (stress approximately 0.55 MPa at 60 % strain), enabling rapid separation and easy regeneration while maintaining high adsorption performance even after five cycles. Significantly, MnO2@CTS exhibited a maximum adsorption capacity of 410.7 mg/g at pH 6 and 298 K, surpassing reported values for most CTS/MnO2-based adsorbents. The chemisorption process of U(VI) on MnO2@CTS followed the pseudo-second-order kinetic and Dubinin-Radushkevish models. X-ray photoelectron spectroscopy analysis further confirmed the reduction of U(VI) to U(V/IV). These findings highlight the substantial potential of MnO2@CTS aerogel beads for U(VI) removal from aqueous solutions, positioning them as a promising solution for addressing U(VI) contamination in wastewater.

Mitigation of arsenic accumulation in rice (Oryza sativa L.) seedlings by oxygen nanobubbles in hydroponic cultures.

Arsenic (As) is a toxic non-essential metal. Its accumulation in rice has not only seriously affected the growth of rice, but also poses a significant threat to human health. Many reports have been published to decrease the arsenic accumulation in the rice plant by various additives such as chemicals, fertilizers, adsorbents, microorganisms and analyzing the mechanism. Nanobubble is a new technology widely used in agriculture because of its long existence time and high mass transfer efficiency. However, a few studies have investigated the effect of nanobubbles on arsenic uptake in rice. This study investigated the effect of oxygen nanobubbles on the growth and uptake of As in rice. The oxygen nanobubbles could rupture the salinity of nutrients and produce the hydroxyl radical. The hydroxyl radical caused the oxidation of arsenic As(III) to As (V) and the oxidation of ferrous ions. At the same time, the oxidized iron adsorbing As (V) created the iron plaque on the rice roots to stop arsenic introduction into the rice plant. The results indicated that the treatment of oxygen nanobubbles increased rice biomass under As stress, while they increased the chlorophyll content and promoted plant photosynthesis. Oxygen nanobubbles reduced the As content in rice roots to 12.5% and shoots to 46.4%. In other words, it significantly decreased As accumulation in rice. Overall, oxygen nanobubbles mitigated the toxic effects of arsenic on rice and had the potential to reduce the accumulation of arsenic in rice.

Controlled synthesis and photocatalytic hydrogen evolution activities of cobalt carbides with different phase compositions.

Cobalt carbides are emerging as promising materials for various magnetic and catalytic applications. However, exploring dedicated cobalt carbides with optimal catalytic properties via adjusting phase compositions remains a significant challenge. Herein, three different cobalt carbides, CoxC (Co2C-Co3C), Co2C-Co, and Co3C, were successfully prepared using a facile one-pot green method. The phase compositions of cobalt carbides could be easily controlled by varying the cobalt-based precursors and carbon sources. More remarkably, three different cobalt carbides could serve as reduction cocatalysts decorated CdS for improved hydrogen production under visible light. Intriguingly, the obtained Co3C/CdS nanocomposite displayed the highest photocatalytic hydrogen evolution activity among the three composites and superior photocatalytic stability. This work provides a fundamental approach to tuning the photocatalytic properties of cobalt carbides for energy conversion fields.

Manganese-Titanium Mixed Ion Sieves for the Selective Adsorption of Lithium Ions from an Artificial Salt Lake Brine.

Lithium recovery is imperative to accommodate the increase in lithium demand. Salt lake brine contains a large amount of lithium and is one of the most important sources of lithium metal. In this study, Li2CO3, MnO2, and TiO2 particles were mixed, and the precursor of a manganese-titanium mixed ion sieve (M-T-LIS) was prepared by a high-temperature solid-phase method. M-T-LISs were obtained by DL-malic acid pickling. The adsorption experiment results noted single-layer chemical adsorption and maximum lithium adsorption of 32.32 mg/g. From the Brunauer-Emmett-Teller and scanning electron microscopy results, the M-T-LIS provided adsorption sites after DL-malic acid pickling. In addition, X-ray photoelectron spectroscopy and Fourier transform infrared results showed the ion exchange mechanism of the M-T-LIS adsorption. From the results of the Li+ desorption experiment and recoverability experiment, DL-malic acid was used to desorb Li+ from the M-T-LIS with a desorption rate of more than 90%. During the fifth cycle, the Li+ adsorption capacity of the M-T-LIS was more than 20 mg/g (25.90 mg/g), and the recovery efficiency was higher than 80% (81.42%). According to the selectivity experiment, the M-T-LIS had good selectivity for Li+ (adsorption capacity of 25.85 mg/g in the artificial salt lake brine), which indicates its good application potential.

Nanobubble size distribution measurement by interactive force apparatus under an electric field.

Nanobubbles have been applied in many fields, such as environmental cleaning, material production, agriculture, and medicine. However, the measured nanobubble sizes differed among the measurement methods, such as dynamic light scattering, particle trajectory, and resonance mass methods. Additionally, the measurement methods were limited with respect to the bubble concentration, refractive index of liquid, and liquid color. Here, a novel interactive force measurement method for bulk nanobubble size measurement was developed by measuring the force between two electrodes filled with bulk nanobubble-containing liquid under an electric field when the electrode distance was changed in the nm scale with piezoelectric equipment. The nanobubble size was measured with a bubble gas diameter and also an effective water thin film layer covered with a gas bubble that was estimated to be approximately 10 nm based on the difference between the median diameter of the particle trajectory method and this method. This method could also be applied to the solid particle size distribution measurement in a solution.

A Critical Review of Snail Shell Material Modification for Applications in Wastewater Treatment.

Sea material is becoming increasingly popular and widely used as an adsorbent in wastewater treatment. Snail shell, a low-cost and natural animal waste material, has been shown to have a high calcium content (>99%) and a large potential surface area for the development of sustainable adsorbents. This paper presents a novel synthesis of methods for using snail shell absorbent materials in the treatment of wastewater containing heavy metals, textile dyes, and other organic substances. Modified biochar made from snail shells has gained popularity in recent years due to its numerous benefits. This paper discusses and analyzes modification methods, including impregnating with supplements, combining other adsorbents, synthesis of hydroxyapatite, co-precipitation, and the sol-gel method. The analysis of factors influencing adsorption efficiency revealed that pH, contact time, temperature, initial concentration, and adsorbent dose all have a significant impact on the adsorption process. Future research directions are also discussed in this paper as a result of presenting challenges for current snail adsorbents.

Different nanobubbles mitigate cadmium toxicity and accumulation of rice (Oryza sativa L.) seedlings in hydroponic cultures.

Cadmium (Cd) contamination can pose a severe threat to food production and human health. The accumulation of Cd in rice will decrease rice biomass, photosynthetic activity, and antioxidant capacity, affecting crop yield. The effects of different nanobubbles on the growth and Cd accumulation of rice seedlings under hydroponic conditions were investigated in this study. The results showed that the biomass, photosynthetic pigment content, and antioxidant enzyme activity of rice seedlings decreased when treated with Cd alone and that Cd induced lipid peroxidation in rice seedlings. However, when different types of nanobubbles were introduced into the nutrient solution, the bioavailability of Cd in the solution was reduced. As a result, the Cd content in rice was significantly decreased compared to treatment with Cd alone. Nanobubbles increased the biomass of rice, enhanced photosynthesis, and improved the antioxidant capacity of rice by increasing antioxidant enzyme activities to alleviate Cd-induced oxidative stress. At the same time, nanobubbles increased the Fe content in rice, which decreased the Cd content, as Cd is antagonistic to Fe. In conclusion, these results suggested that nanobubbles are a potential method of mitigating Cd stress that may help to improve rice yield and could be further explored in production.

Preparation of VCo-MOF@MXene composite catalyst and study on its removal of ciprofloxacin by catalytically activating peroxymonosulfate: Construction of ternary system and superoxide radical pathway.

The synergistic effect between transition metal active centers and the generation of multiple removal pathways has a significant impact on the catalytic activation efficiency of peroxymonosulfate. In this work, a kind of composite catalyst was prepared by growing VCo-metal-organic frameworks (VCo-MOF) in-situ on the surface of Ti3C2Tx by a solvothermal method. The morphology and structure are characterized by Transmission Electron Microscope (TEM), Energy Dispersion Spectrum (EDS), Atomic Force Microscope (AFM), etc. Response surface methodology was used to optimize the experimental conditions. Only 5 mg catalyst can be used to effectively activate PMS and remove 96.14 % ciprofloxacin (CIP, 20 mg/L) within 30 min. The removal effect of catalyst on CIP in different actual water environment was explored. In addition, the fluorescence spectrum test also verified the effective removal of ciprofloxacin. V-Co-Ti ternary system provides a wealth of active sites for CIP removal. Cyclic voltammetry (CV) and lear sweep voltammetry (LSV) tests showed the existence of the electron transfer pathway. The results of density functional theory (DFT) calculation show that VCo-MOF@Ti3C2Tx has excellent adsorption and activation ability for PMS. At the same time, the hydrophilicity of the catalyst makes PMS more inclined to react with water molecules, which promotes the formation of a unique superoxide radical path.

Efficient preparation of red mud-based geopolymer microspheres (RM@GMs) and adsorption of fluoride ions in wastewater.

In this paper, red mud-based geopolymer microspheres (RM@GMs: 75-150 µm) was prepared by dispersion-suspension-solidification method to remove fluoride ions (F-). It was found that RM@GMs still had good mechanical properties and better F- removal effect at RM content reached 80 % of the total solid mass. The batch adsorption experiment results showed that the F- concentration (< 1.5 mg/L) reached the drinking water standard in 45 min at pH = 2 and RM@GMs dosage was 1 g/L. RM@GMs showed maximum adsorption capacity of 76.57 mg/g for F-, and the adsorption kinetics and isotherm fitted the pseudo-second-order kinetic and Langmuir isotherm model, respectively. RM@GMs exhibited excellent dynamic separation effect at the flow rate of 4 mL/min and column height of 1 cm. In addition, RM@GMs had good selectivity for F- in the competitive adsorption experiments and followed an order of: PO43- > > SO42- ≈ NO3- ≈ Cl-. In real seawater, natural surface water and tap water, RM@GMs still had excellent F- removal effect. The adsorption mechanism revealed that RM@GMs removed F- mainly through the synergistic effect of adsorption and ion exchange. Therefore, this paper provides the potential value for the large-scale utilization of RM in the application of F--containing wastewater.

Three-dimension titanium phosphate aerogel for selective removal of radioactive strontium(II) from contaminated waters.

The effective removal of radioactive strontium (especially 90Sr) from nuclear wastewater is crucial to environmental safety. Nevertheless, materials with excellent selectivity in Sr removal remain a challenge since the similarity with alkaline earth metal ions in the liquid phase. In this work, a novel titanium phosphate (TiP) aerogel was investigated for Sr(II) removal from the radioactive wastewater based on the sol-gel method and supercritical drying technique. The TiP aerogel has amorphous, three-dimensional and mesoporous structures with abundant phosphate groups, which was confirmed by X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), atomic force microscope (AFM) and Fourier transform infrared spectroscopy (FT-IR). The adsorbent exhibited high efficiency and selectivity for the removal of Sr(II) with an extensive distribution coefficient up to 4740.03 mL/g. The adsorption equilibrium reached within 10 min and the maximum adsorption capacity was 373.6 mg/g at pH 5. And the kinetics and thermodynamics data fitted well with the pseudo-second-order model and Langmuir model respectively. It can be attributed to the rapid trapping and slow intraparticle diffusion of Sr(II) inside the mesoporous channels of the TiP aerogel. Furthermore, TiP aerogel exhibited over 80% removal for 50 mg/L Sr2+ in real water systems (seawater, lake water and tap water). X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy revealed that strong ionic bonding formed during Sr(II) adsorption with the phosphate group on TiP aerogel. These results indicated that TiP aerogel is a promising high-capacity adsorbent for the effective and selective capture of Sr(II) from radioactive wastewater.

Chestnut Shell-Activated Carbon Mixed with Pyrolytic Snail Shells for Methylene Blue Adsorption.

Activated carbon has been used to treat organic dyes in water systems; however, the adsorption capacity of the samples studied was limited by the specific surface area and influenced by the pH of the aqueous solution. In this study, a hybrid adsorbent consisting of a mixture (MCS) of activated chestnut shell biochar (CN) and pyrolyzed snail shell material (SS) was developed to solve this problem, with the waste snail shell samples being processed by pyrolysis and the chestnut shell samples chemically pretreated and then pyrolyzed. The BET and SEM results revealed that the SS had a mesoporous fluffy structure with a higher specific surface (1705 m2/g) and an average pore diameter of about 4.07 nm, providing a large number of sites for adsorption. In addition, XPS and FTIR results showed that the main component of SS was calcium oxide, and it also contained a certain amount of calcium carbonate, which not only provided an alkaline environment for the adsorption of biochar but also degradation and photocatalytic capabilities. The results showed that the MCS3-1 sample, obtained when CN and SS were mixed in the ratio of 3:1, had good capacity for adsorption for methylene blue (MB), with 1145 mg/g at an initial concentration of 1300 mg/L (92% removal rate). The adsorption behaviors were fitted with the pseudo-second-order kinetic model and Freundlich isotherm model, which indicated that the adsorption was multilayer chemisorption with a saturated adsorption capacity of 1635 mg/g. The photocatalytic capacity from the SS composition was about 89 mg/g, and the sorption of MB dye onto the sorbent reached equilibrium after 300 min. The results suggested that MCS3-1 has enormous potential for removing MB from wastewater.

The Influence of Air Nanobubbles on Controlling the Synthesis of Calcium Carbonate Crystals.

Numerous approaches have been developed to control the crystalline and morphology of calcium carbonate. In this paper, nanobubbles were studied as a novel aid for the structure transition from vaterite to calcite. The vaterite particles turned into calcite (100%) in deionized water containing nanobubbles generated by high-speed shearing after 4 h, in comparison to a mixture of vaterite (33.6%) and calcite (66.3%) by the reaction in the deionized water in the absence of nanobubbles. The nanobubbles can coagulate with calcite based on the potential energy calculated and confirmed by the extended DLVO (Derjaguin-Landau-Verwey-Overbeek) theory. According to the nanobubble bridging capillary force, nanobubbles were identified as the binder in strengthening the coagulation between calcite and vaterite and accelerated the transformation from vaterite to calcite.

Improved leaching of Cu, Sn, Pb, Zn, and Al from waste printed circuit boards by electro-generated Cl2 in HCl solution.

This paper investigated the improved leaching of Cu, Sn, Pb, Zn, and Al from waste printed circuit boards (WPCBs) by electro-generated Cl2 in HCl solution through multiple leaching cells in series, double intake pipes, and bubble stone for leaching. The leaching agents in the leaching cell include Cl2(aq), HCl, HClO, and Cl3-. The leaching rate and leaching speed of Zn, Sn, Al, and Pb exceeded that of Cu. Leaching time and HCl concentration have a strong impact on the dissolution of Cu, whereas the effect of the electrolytic current and the leaching temperature is comparably weak. The series of leaching cells improved the effective utilization of Cl2 and increased the treatment capacity of the WPCBs. Bubble stones significantly enhanced the efficiency and rate of leaching. Reduction of the size of the Cl2 gas bubbles improved the leaching kinetics. The leaching rate of Cu reached 87.22%, whereas the leaching rate of Zn, Sn, Al, and Pb exceeded 90% after 100 min. Our experimental data provide a reference for electrolytic leaching recovery of metals from WPCBs, and our method improves the metal leaching and electrolytic efficiency in practice.

Utilization of Waste Amine-Oxime (WAO) Resin to Generate Carbon by Microwave and Its Removal of Pb(II) in Water.

Utilising waste amine-oxime (WAO) resin through microwave semi-carbonization, a carbon adsorbent (CA) was obtained to remove Pb(II). After microwave treatment, the pore size of the skeleton structure, three-dimensional porous network, and lamellar pore structure of WAO was improved. The distribution coefficient (Kd) of Pb(II) onto CA is 620 mL/g, and the maximum adsorption capacity of Pb(II) is 82.67 mg/g after 20 min of WAO microwave treatment. The adsorption kinetics and adsorption isotherms conform to the quasi-second-order kinetic equation and Langmuir adsorption isotherm model, respectively. The surface of MT-WAO is negatively charged and the adsorption mechanism is mainly electrostatic interaction. Pb(II) elution in hydrochloric acid solution is more than 98%, and its recovery is high at 318 K and for 1 h.