Influence of different printing orientations and post-polymerization time on the translucency of three-dimensional (3D) printed denture base resins.

PURPOSE: To evaluate the effect of different printing orientations and post-polymerization time with thermal cycling on the translucency of 3D-printed denture base resins. METHODS: Heat-polymerized (HP) acrylic resin specimens were fabricated and 3D-printed denture base materials (NextDent, ASIGA, FormLabs) were printed with different printing orientations (0, 45, 90 degrees) and subjected to different post-polymerization times (15-, 30-, 60-, and 90-min). All specimens were polished and immersed in distilled water for 1 day at 37°C. CIEDE2000 was used to measure the translucency parameters (TP00) before and after thermal cycling (5000 cycles) recording the color parameters (L*, a*, b*) against a black and white background using a spectrophotometer. k-factors ANOVA followed by post hoc Tukey's test (α = .05) was performed for statistical analysis. RESULTS: The k-factors ANOVA test showed a significant effect of resin material, post-polymerization time, and printing orientation on translucency (p < 0.001). In comparison to HP, all 3D-printed resins showed lower translucency with all post-polymerization times and printing orientation (p < 0.001) except FormLabs resin (p > 0.05). For all 3D-printed resins, the translucency increased, with increasing the post-polymerization time (p < 0.001) and 60- and 90-min showed the highest translucency. For printing orientation, 90 and 45 degrees significantly showed high translucency in comparison to 0 degrees (p < 0.001). FormLabs showed significantly higher translucency when compared with NextDent and ASIGA per respective printing orientation and post-polymerization time. The translucency significantly decreased after thermal cycling for all tested resins (p < 0.001). CONCLUSION: The findings of this study demonstrated that the translucency of 3D-printed resins is influenced by the printing orientation, post-polymerization time, and resin type. As a result, choosing a resin type, and printing orientation, with a longer post-polymerization time should be considered since it may improve the esthetic appearance of the 3D-printed resins.

Comparative analysis of dimensional changes in autoclavable polyvinyl siloxane (PVS) impressions under various Sterilization/Disinfection Protocols: A randomized controlled trial.

Background: Impressions that maintain their dimensional stability after autoclaving effectively control cross-infection and contamination resulting from a patient's oral secretions. Purpose: The study aimed to assess the dimensional stability of autoclavable polyvinyl siloxanes after disinfection and sterilization. Methods: A stainless steel metal model containing three full veneer crown preparations was fabricated according to ANSI/ADA specification No. 19. Reference grooves were established on the occlusal and axial surfaces of the abutments for accurate measurements. Forty impressions were created from the master model using single-step impression technique monophase polyvinyl siloxane material (AFFINIS, Coltene/Whaledent, Altstatten, Switzerland). The impressions were categorized into four groups: Group A (control, ten untreated impressions), Group B (ten disinfected impressions with 5.25 % sodium hypochlorite [NaOCl]), Group C (ten disinfected impressions with 2 % glutaraldehyde), and Group D (ten autoclaved impressions at 134 °C for 18 min). Subsequently, stone casts were produced using type IV gypsum products (Gelstone R, BK Giulini Chemie, Ludwigshafen/Rh., Germany). The dimensional accuracy of the obtained casts was assessed by measuring the inter-abutment measurements (between the abutments) and the intra-abutment measurements (diameter and height of the abutments). These measurements were performed using a universal measuring microscope (Olympus stereomicroscope B061 Imaging Corp. Tokyo, Japan) with a precision of 0.001 mm. The dimensions of the stone casts from the study groups were then compared to those of the control group. Data analysis was performed using a one-way ANOVA with a significance level of α = 0.05. Results: AFFINIS impressions subjected to chemical disinfection in 5.25 % NaOCl and 2 % glutaraldehyde with different immersion times showed slight expansion in the intra- and inter-abutment measurements. The impressions autoclaved at 134 °C for 18 min showed slight shrinkage in the intra- and inter-abutment measurements. The dimensional change was statistically non-significant, and the percent of dimensional changes within the experimental groups was within the clinically accepted limit (α < 0.5). Conclusion: AFFINIS polyvinyl siloxanes retain dimensional stability suitable for clinical use when subjected to chemical disinfection and steam autoclaving.

Color and flexural properties of nanoparticles-modified denture base resin: An in vitro comparative study.

Objectives: Reinforcement of polymethylmethacrylate (PMMA) denture base resins (DBRs) with inorganic fillers with superior properties and accepted aesthetics are favored and still a big dilemma. This study was undertaken to evaluate the color change, flexural strength, and modulus of elasticity of heat-polymerized DBR material modified with silver nanoparticles (AgNPs) and zirconium dioxide nanoparticles (ZNPs). Methods: Sixty acrylic specimens (30/color test, 30/flexural properties) were fabricated and divided according to nanoparticles type and addition into 3 groups (n = 10). Group-I; unmodified specimens, Group-II; modified specimens with 0.5wt% AgNPs (PMMA/AgNPs), and Group-III; modified specimens with 7.5wt% ZNPs (PMMA/ZNPs). Disc-shape (20 × 3 mm) and bar-shape (65 × 10 × 2.5 mm) specimens were fabricated for color and flexural properties, respectively. The spectrophotometer was used for evaluation of the color change (∆E). The flexural strength and elastic modulus evaluation was carried out using a 3-point bending test (5 mm/min). Tukey's post hoc and one-way ANOVA were used to analyze the data at a significant level P ≤ 0.05. Results: PMMA/AgNPs group exhibited a significant increase in color change when compared with PMMA/ZNPs. PMMA/ZNPs showed significantly the highest flexural strength value when compared with unmodified and PMMA/AgNPs groups (P < 0.001), however, there was an absence of significant differences in terms of flexural strength values between PMMA/AgNPs and unmodified groups (P > 0.05). PMMA/AgNPs insignificantly increased its modulus of elasticity strength (P = 0.09410) while PMMA/ZNPs significantly increased its modulus of elasticity strength (P = 0.00396). Conclusion: The AgNPs and ZNPs addition to PMMA increased the color change and AgNPs change the color of DBRs. The flexural attributes of DBRs have been increased by ZNPs.

Impact of Nanoparticle Addition on the Surface and Color Properties of Three-Dimensional (3D) Printed Polymer-Based Provisional Restorations.

This study aimed to evaluate and compare the impact of additives such as ZrO2 and SiO2 nanoparticles (ZrO2NP or SiO2NP) on the hardness, surface roughness, and color stability of 3D printed provisional restorations. Two hundred samples in total were printed using 3D printed resins (ASIGA, and NextDent). Each resin was modified with ZrO2NPs or SiO2NPs in two different concentrations (0.5 wt% and 1 wt%), while one group was kept unmodified (n = 10). Disc-shaped (15 × 2.5 mm) samples were designed and printed in accordance with the manufacturer's recommendation. Printed discs were evaluated for color changes through parameters CIELAB 2000 system (ΔE00), hardness using Vickers hardness test, and surface roughness (Ra) using a noncontact profilometer. After calculating the means and standard deviations, a three-way ANOVA and Tukey post hoc test were performed at α = 0.05. The addition of ZrO2NPs or SiO2NPs to ASIGA and NextDent resins significantly increased the hardness at a given level of concentration (0.5% or 1%) in comparison with pure (p < 0.001), with no significant difference between the two modified groups per resin type (p > 0.05). The highest hardness value was detected in 1% ZrO2NPs with 29.67 ± 2.3. The addition of ZrO2NPs or SiO2NPs had no effect on the Ra (p > 0.05), with 1% ZrO2NPs showing the highest value 0.36 ± 0.04 µm with NextDent resin. ZrO2NPs induced higher color changes (∆E00), ranging from 4.1 to 5.8, while SiO2NPs showed lower values, ranging from 1.01 to 1.85, and the highest mean ∆E00 was observed in the 1% ZrO2NPs group and NextDent resin. The incorporation of ZrO2NPs and SiO2NPs in 3D printed provisional resins increased the hardness without affecting the surface roughness. The optical parameters were significantly affected by ZrO2NPs and less adversely affected by SiO2NPs. Consequently, care must be taken to choose a concentration that will improve the materials' mechanical performance without detracting from their esthetic value.

Denture relining using digital replication method: A dental technique.

The aim of this report was to digitize traditional denture relining using a digital duplication method, in addition to assessing the wear resistance of three-dimensional (3D) printed denture teeth. A complete denture was relined using light body impression. The denture with impression was scanned yielding a standard tessellation language file that was designed to print the denture base and teeth. The printed teeth were fitted into the sockets of the printed denture base and then bonded using auto-polymerized acrylic resins, followed by finishing and polishing. Dentures were inserted and fit and occlusion were adjusted as needed, and the patient was scheduled for follow-up appointments at one week, three months, and six months. At each follow-up visit, dentures were scanned using a 3Shape E3 desktop scanner and scans were superimposed. The occlusal wear was assessed in reference to the first scan after the denture insertion visit. The accuracy of the intaglio surface of dentures was within clinically acceptable limits. The clinical evaluation of inserted dentures in terms of retention, occlusion, esthetic, and patient satisfaction was encouraging. Using digital duplication, conventional dentures could be relined. The advantages of digital records include eliminating polymerization dimensional changes, and reducing cost and clinical time by minimizing the number of visits, which is particularly helpful with geriatric patients.

Effect of Duplication Techniques on the Fitting Accuracy of CAD-CAM Milled, 3D-Printed, and Injection-Molded Mandibular Complete Denture Bases.

BACKGROUND: Digital technology has been introduced in prosthodontics, and it has been widely used in denture duplication instead of a conventional denture duplication technique. However, research comparing different denture duplication techniques and how they affect the fitting accuracy of the denture base is scarce. OBJECTIVES: The aim was to assess the impact of duplication techniques on the accuracy of the fitting surface of computer-aided design and manufacturing (CAD-CAM) milled, 3D-printed, and injection-molded complete denture bases (CDBs). METHODOLOGY: This study involved fabricating a mandibular complete denture base with three marked dimples as reference marks (A, B, and C at the incisive papilla, right molar, and left molar areas) using a conventional compression molded technique. This denture was then scanned to generate a standard tessellation language (STL) file; after that, it was duplicated using three different techniques (milling, 3D printing, and injection molding) and five denture base resin materials-two milled CAD-CAM materials (AvaDent and IvoBase), two 3D-printed materials (NextDent and HARZ Labs), and one injection-molded material (iFlextm). Based on the denture base type, the study divided them into five groups (each with n = 10). An evaluation of duplication accuracy was conducted on the fitting surface of each complete denture base (CDB) using two assessment methods. The first method was a two-dimensional evaluation, which entailed linear measurements of the distances (A-B, A-C, and B-C) between reference points on both the scanned reference mandibular denture and the duplicated dentures. Additionally, a three-dimensional superimposition technique was employed, involving the overlay of the STL files of the dentures onto the reference denture's STL file. The collected data underwent statistical analysis using a one-way analysis of variance and Tukey's pairwise post hoc tests. RESULTS: Both evaluation techniques showed significant differences in fitting surface accuracy between the tested CDBs (p ˂ 0.001), as indicated by one-way ANOVA. In addition, the milled CDBs (AvaDent and IvoBase) had significantly higher fitting surface accuracy than the other groups (p ˂ 0.001) and were followed by 3D-printed CDBs (NextDent and HARZ Labs), while the injection-molded (iFlextm) CDBs had the lowest accuracy (p ˂ 0.001). CONCLUSIONS: The duplication technique of complete dentures using a CAD-CAM milling system produced superior fitting surface accuracy compared to the 3D-printing and injection-molded techniques.

Flexural strength of 3D-printed nanocomposite provisional resins: Impact of SiO2 and ZrO2 nanoparticles and printing orientations in vitro.

PURPOSE: The aim of this study was to investigate and compare the influence of zirconium dioxide nanoparticles (ZrO2 NPs) and silicon dioxide nanoparticles (SiO2 NPs) addition and printing orientation on the flexural strength (FS) of provisional three-dimensional (3D) printing resins undergoing thermal cycling (TC). METHODS: Three dimensional-printed resin (NextDent C&B MFH) was used to fabricate 300 bar-shaped specimens (25 × 2 × 2 mm3 ). The ZrO2 NPs and SiO2 NPs specimens were divided into two groups, then subdivided into three groups, based on the nanoparticle concentration (i.e., 0 wt% (original group), 0.5 wt%, and 1 wt%). Each concentration was printed in three printing orientations (0°, 45°, and 90°). The printed specimens were exposed to 5000 cycles of TC, followed by a three-point bending test to assess the FS. Fracture surface analysis was conducted by using a scanning electron microscope (SEM). For data analysis, ANOVA and Tukey's post hoc were utilized (α = 0.05). RESULTS: Compared to the original material, the addition of ZrO2 NPs and SiO2 NPs had a significantly positive impact on the FS, (P > 0.001). After TC, the FS of the original group decreased significantly and had the lowest value. The highest FS value was observed in 1% ZrO2 NPs at 0°. Regardless of the nanoparticle concentration, the 0° orientation consistently showed a higher FS, compared to the 45° and 90° orientations. At all orientations (i.e., 0°, 45°, and 90°), the FS significantly increased with the addition of NPs, compared with that of the original material (P > 0.001). TC had a significantly negative effect on the FS of the unmodified groups. However, no significant differences existed in FS among the modified groups after TC. CONCLUSION: The addition of SiO2 NPs and ZrO2 NPs increased the FS of the 3D-printed provisional resin. Regardless of the nanoparticle concentration, the 0° orientation had the higher FS. TC had an effect on the original resin, whereas it had no significant effect on the nanoparticle-modified resins. In clinical practice, 3D-printed provisional nanocomposite resins printed at the 0° orientation could be recommended for long-term dental provisional restorations.

Denture care and oral health-related quality of life among complete denture wearers in Eastern Province of Saudi Arabia.

INTRODUCTION: This study aimed to evaluate denture care and hygiene and oral health-related quality of life (OHRQoL) among complete denture (CD) wearers in the Eastern Province of Saudi Arabia. METHODOLOGY: This cross-sectional study was conducted on CD wearers in the Eastern Province of Saudi Arabia. A pre-tested questionnaire was administered among study participants. Questionnaire was divided in three sections: (1) patients' demographic data, (2) awareness and maintenance of CD and (3) OHRQoL. Independent sample t-test and one-way ANOVA test were performed. RESULTS: The study included data of 300 participants with 71% of males and 28% of females. Majority of participants (82.7%) cleaned CD daily, removed CD while sleeping (88.0%) and knew that unhygienic dentures can cause oral infection (92.7%). Only 19.3% used denture cleansing tables, 41% used toothpaste, and 60.7% rinsed CD with water. Regarding OHIP-DENT domains, highest score was for functional limitation domain (2.20 ± 1.67) and the lowest for handicap domain (0.94 ± 1.09). The mean OHIP-DENT score of the sample was 12.02 ± 8.52. Females (p = 0.006), participants below 65 years of age (p = 0.029), non-Saudis (p = 0.042), those with university education (p = 0.030) and low monthly income (p = 0.045) and participants who visited dentist due to problem with CD (p = 0.041) demonstrated significantly higher mean OHIP-DENT score. CONCLUSION: Majority of participants demonstrated appropriate denture care behaviours because they were aware of the importance of denture care and hygiene. Female gender, age below 65 years, non-Saudi nationality, university education, low monthly income and visiting dentist due to problem were related to poor OHRQoL.

Effect of repair and surface treatments on the strength of digitally fabricated resin-based dental prostheses: A systematic review of in vitro studies.

OBJECTIVE: This review investigated the current literature pertaining to the repairability of computer-aided design-computer-aided manufacturing (CAD-CAM) milled and three-dimensional (3D) printed resin-based dental prostheses (RBDPs) as well as the appropriate surface treatment for each repair material that will produce adequate repair bond strength. DATA/SOURCES: PubMed, Web of Science, and Scopus databases were searched for published articles involving repair of CAD-CAM RBDPs between January 2010 and June 2023. Data were collected and analyzed to reveal the surface treatment effects, suggested repair materials, and strength of repaired RBDPs. STUDY SELECTION: Out of 164 retrieved titles, 11 studies were included, of which five investigated the repair of 3D-printed RBDPs, three investigated the repair of CAD-CAM milled resins, and three investigated both materials. Additionally, of the included studies, seven investigated denture base resins, three studied provisional restoration resins, and one evaluated 3D-printed intraoral splints. Various surface treatments were suggested, with air-abrasive methods being the most commonly used. Different materials for resin repair were proposed and used, including auto-polymerized, reline, and composite resins. For 3D-printed resins, repair with Bis-acrylic/Bis-GMA composites improved repair strength. CONCLUSION: Surface treatments positively affected the repair strength of conventional and milled RBDPs. However, challenges remain relevant to the repair of 3D-printed resins owing to composition mismatches and fabrication techniques. Therefore, further investigation is required to develop new 3D-printed resins. CLINICAL SIGNIFICANCE: CAD-CAM milled resins have satisfactory repair strength, which increases with surface treatment. The repair of 3D-printed resins has proven challenging even with surface treatments. However, composite resins are the materials of choice.

Comparative Evaluation of TiO2 Nanoparticle Addition and Postcuring Time on the Flexural Properties and Hardness of Additively Fabricated Denture Base Resins.

Three-dimensionally (3D)-printed fabricated denture bases have shown inferior strength to conventional and subtractively fabricated ones. Several factors could significantly improve the strength of 3D-printed denture base resin, including the addition of nanoparticles and post-curing factors. This study evaluated the effect of TiO2 nanoparticle (TNP) addition and the post-curing time (PCT) on the flexural properties and hardness of three-dimensionally (3D)-printed denture base resins. A total of 360 specimens were fabricated, with 180 specimens from each type of resin. For evaluating the flexural properties, bar-shaped specimens measuring 64 × 10 × 3.3 mm were used, while, for the hardness testing, disc-shaped specimens measuring 15 × 2 mm were employed. The two 3D-printed resins utilized in this study were Asiga (DentaBASE) and NextDent (Vertex Dental B.V). Each resin was modified by adding TNPs at 1% and 2% concentrations, forming two groups and an additional unmodified group. Each group was divided into three subgroups according to the PCT (15, 60, and 90 min). All the specimens were subjected to artificial aging (5000 cycles), followed by testing of the flexural strength and elastic modulus using a universal testing machine, and the hardness using the Vickers hardness test. A three-way ANOVA was used for the data analysis, and a post hoc Tukey's test was used for the pairwise comparisons (α = 0.05). Scanning electron microscopy (SEM) was used for the fracture surface analysis. The addition of the TNPs increased the flexural strength in comparison to the unmodified groups (p < 0.001), while there was no significant difference in the elastic modulus and hardness with the 1% TNP concentration. Among the TNP groups, the 2% TNP concentration significantly decreased the elastic modulus and hardness (p < 0.001). The SEM showed a homogenous distribution of the TNPs, and the more irregular fracture surface displayed ductile fractures. The PCT significantly increased the flexural strength, elastic modulus, and hardness (p < 0.001), and this increase was time-dependent. The three-way ANOVA results revealed a significant difference between the material types, TNP concentrations, and PCT interactions (p < 0.001). Both concentrations of the TNPs increased the flexural strength, while the 2% TNP concentration decreased the elastic modulus and hardness of the 3D-printed nanocomposites. The flexural strength and hardness increased as the PCT increased. The material type, TNP concentration, and PCT are important factors that affect the strength of 3D-printed nanocomposites and could improve their mechanical performance.

In Vitro Evaluation of Candida albicans Adhesion and Related Surface Properties of CAD/CAM Denture Base Resins.

OBJECTIVE: The aim of this study was to evaluate the surface roughness, contact angle, and adhesion of Candida albicans to computer-aided designing/computer-aided manufacturing (CAD/CAM) and heat-polymerized (HP) denture base materials. MATERIALS AND METHODS: Specimens were allocated to six groups based on the composition of studied denture base materials, HP acrylic resin, milled resins (AvaDent and IvoCad), and 3D-printed resins (ASIGA, FormLabs, and NextDent). Ten specimens per group were used for each test (n = 10/test). Surface roughness and contact angles were analyzed using profilometer and goniometer, respectively. Adhesion of C. albicans was counted using colony-forming unit (CFU/mL). Means and standard deviations were calculated, and then one-way analysis of variance (ANOVA), followed by Tukey's post hoc test. Correlation of Candida adhesion and surface parameters was determined by using Pearson's correlation analysis. RESULTS: No statistically significant difference was noted in surface roughness between HP, milled, and 3D-printed denture base resins except NextDent, which showed significantly higher roughness in comparison to all other resins (p = 0.001). In terms of contact angle, milled resins had the lowest value, followed by HP, ASIGA, and FormLabs, whereas NextDent showed the highest contact angle (p = 0.001). C. albicans adhesion showed no significant difference between all denture base resins. A positive and significant correlation was found between C. albicans adhesion and contact angle (p = 0.003), while no correlation was reported between C. albicans adhesion and surface roughness (p = 0.523). CONCLUSION: Adhesion of C. albicans was similar in all tested specimens. Surface roughness showed no significant difference between all groups except NextDent, which had the highest value. Milled denture base resins had the lowest contact angle among all groups.

Effect of Different Occlusal Tooth Forms of Mandibular Overdenture Retained by an Immediate Loaded Single Implant on the Masticatory Efficiency and Oral Health-Related Quality of Life.

Aim: To study the masticatory efficacy and oral health-related quality of life (OHRQoL) of participants wearing a mandibular overdenture retained by an immediate loading single implant with different occlusal tooth forms. Materials and Methods: For this nonrandomized controlled trial study, 27 edentulous participants were selected and randomly divided into three groups (n = 9) based on occlusal tooth forms of the mandibular implant overdenture (MIOD). Group I: participants received an MIOD with an anatomical tooth form; Group II: participants received an MIOD with a semianatomical tooth form; and Group III: participants received an MIOD with a nonanatomical tooth form. For each participant, a single implant (screw root form) was inserted into the midline of the mandibular ridge to support the MIOD. For each group, the masticatory efficiency was evaluated after 3 months, and the OHRQoL of the participants was evaluated after 3 and 6 months. One-way ANOVA and post hoc Tukey's test were used for data analysis (P < 0.05). Results: The masticatory efficiency of the anatomic and semianatomic tooth forms was higher than that of the nonanatomic (P < 0.05). Moreover, the improvement in the participants' OHRQoL in the anatomic group was more significant than that of other groups (P < 0.05). Conclusion: There was a greater improvement in masticatory efficiency and participants' OHRQoL when fitted with an anatomic tooth form mandibular overdenture retained by an immediate loading single implant than with a semianatomic or nonanatomic tooth form.

Influence of denture brushing on the surface properties and color stability of CAD-CAM, thermoformed, and conventionally fabricated denture base resins.

PURPOSE: To assess the influence of denture brushing on the surface roughness, hardness, and color stability of conventional, thermoformed, and CAD-CAM denture base materials. MATERIALS AND METHODS: Seven different denture base materials were included in this study; conventional heat-polymerized acrylic resin (PMMA) served as control, polyamide, acetal, two categories of milled acrylic discs (AvaDent and IvoCad), and two categories of 3D-printed resins (NextDent and FormLabs). The specimens were constructed according to manufacturers' instructions and then subjected to simulated brushing (20,000 cycles). According to the brushing method, the specimens were split into three groups, no brushing, brushing with water, and brushing with toothpaste. Surface roughness, hardness, and color change were evaluated before and after brushing. Collected data were analyzed using ANOVA, and post-hoc Tukey's tests (α = 0.05). RESULTS: A significant difference was noted between the surface roughness of the tested materials before and after denture brushing (p < 0.05), and milled resin showed the least Ra values. Denture brushing with water significantly increased the Ra of PMMA (p = 0.004) and IvoCad (p = 0.032), while brushing using toothpaste did not show a significant increase. The brushing protocols did not alter the hardness of tested materials except that of PMMA (p = 0.001). The color stability of the tested materials showed comparable results with both brushing protocols. CONCLUSION: The tested properties showed variations between the types of denture base resins. Hardness and color stability of CAD-CAM and thermoformed denture base resins were not altered by denture brushing and showed comparable results with both brushing methods. Surface roughness was the only property that showed alteration after denture brushing.

Impact of international collaboration on dentistry related papers published in Kingdom of Saudi Arabia.

Objective: This bibliographic analysis was designed to review all dental publications in the Kingdom of Saudi Arabia (KSA) and evaluate the effect of international collaboration on the impact of published articles. Methods: The Web of Science (WOS) database was used to extract all related published articles in the KSA from 1982 to 2021. The keywords were connected using Boolean Operators to download related articles. Downloaded articles were screened according to the following inclusion criteria: collaboration journal category, journal discipline, number of citations, number of authors, and impact factor. After applying the inclusion criteria and excluding single-author articles, 5,689 documents were included in the final analysis. The chi-square test and two-independent samples t-test were used to determine the statistical significance between the variables. Results: A significantly higher proportion of articles with international collaboration (51.4%) were published in dental journals than those published nationally (43.3%) or within the institutional level (41.8%) (P < 0.0001). In addition, the average number of citations (9.28 ± 23.8) ranged from 0 to 749, received by an article and the impact factor of the journal in which the article was published, significantly higher in the case of internationally collaborative work compared with national or within institutional collaboration (P < 0.0001). Conclusion: International collaboration positively affected the impact factor, number of citations, and quartile rank of published articles. Moreover, the number of co-authors in different countries contributes to the international collaboration effect.

Fracture Strength of Composite Rest Seats: An In Vitro Comparative Study of Different Composite versus Amalgam Restorations.

Occlusal rest provides support for removable partial dentures (RPD). Rest seats are ideally prepared in enamel, but the abutment teeth might be restored or need restorations. This study compared the fracture strength of abutments restored with composite to amalgam restorations after rest seat preparation. Disto-occlusal cavities were prepared in 30 extracted human maxillary premolars. The specimens were allocated in three groups (n = 10) based on the type of restoration. All the specimens were exposed to thermomechanical aging followed by cycling loading. Fracture strength was tested using a universal testing machine, and then, the fracture mode was recorded. The data were analyzed using Kruskal-Wallis test with a significance level set at 0.05. The fracture mode was recorded as catastrophic or non-catastrophic. The fracture strength between all tested groups showed no significant difference. The highest and lowest fracture strength were recorded on amalgam and Tetric N-Ceram groups, respectively. Composite Tetric N-Ceram showed equal distribution of fracture sites on the restorative materials and teeth, it also displayed the highest number of non-catastrophic fractures unlike other groups where the fracture occurred more within the restorations. The fracture strength of composite was comparable to that of amalgam restorations with prepared rest seats.

Influence of Denture Cleansers on the Retention Loss of Attachment Systems Retained Implant Overdenture.

Background: This study aimed to evaluate the effects of different denture cleansing solutions (DCSs) on the retention of Locator and Locator R-Tx attachment systems of implant retained overdentures (IRO). Methods: Two part acrylic resin blocks were fabricated, upper part contained metal housing and plastic inserts and lower part contained implant analogs and abutments. Eighty pink plastic inserts (40/attachment, 10/solution) were immersed in Corega, Fittydent, sodium hypochlorite, and water for a time simulating upto 1-year of clinical usage. Acrylic blocks were held on a universal testing machine for a pull-out test to record the dislodgement force. Measurements were conducted after 6 months (T1) and 12 months (T2). One-way ANOVA followed by Tukey's HSD test was used to analyze the results (α = 0.05). Results: For both attachments, retention significantly decreased after immersion in different solutions at T2 (P < 0.001). Locator R-Tx attachment in NaOCl showed a significant decrease in retention compared with other solutions at T1. At T2, there was a significant decrease in retention for all DCS compared with water (P < 0.001). Locator R-TX showed higher retention values per solution compared to Locator attachment (P < 0.001). In terms of retention loss %, NaOCl recorded the highest (61.87%) loss, followed by Corega (55.54%) and Fittydent (43.13%), whereas water demonstrated the best retention (16.13%) in both groups. Conclusion: Locator R-TX has better retention with different DCS immersion. The loss of retention varied with different types of DCS and NaOCl recorded the highest retention loss. Therefore, denture cleanser selection must be guided by the type of IRO attachment.

Comparative evaluation of the accuracy of 3D-printed denture teeth.

Objective: This in vitro study compares the accuracy and trueness of various 3D-printed denture teeth. Methods: A total of 30 specimens were created using various 3D-printed resins, 10 each using Asiga DentaTOOTH resin (Asiga, Australia), Formlabs Denture Teeth Resin (Formlabs GmbH, Germany), and NextDent C&B MFH (Micro Filled Hybrid) resin (Nextdent B.V., Netherlands), respectively. A prefabricated mandibular first molar was scanned using a desktop laser scanner (E3, 3Shape A/S) to create a standard tessellation language file, which served as a "reference tooth" scan. That file was sent to each corresponding printer for printing according to manufacturer recommendations. The printed teeth were scanned with an intraoral scanner (TRIOS 3, 3shape, Copenhagen, Denmark). Trueness and precision were assessed using 3D morphometric analysis software (Geomagic Control X, 3D Systems, Rock Hill, SC, USA). One-way ANOVA was used to analyze the data (α = 0.05). Root mean square error and mean deviations were also calculated. Data analysis was carried out using SPSS (IBM Corp., New York, NY, USA) software. One-way ANOVA with Tukey's post hoc analysis was used. P-values of<0.05 were regarded as statistically significant. Results: The overall trueness of teeth followed a similar pattern, with the highest trueness recorded with NextDent specimens, while ASIGA specimens had the lowest. When precision was assessed, there were significant differences in occlusal areas between FormLabs and NextDent specimens (p = 0.01) and between FormLabs and ASIGA specimens (p = 0.002). However, ASIGA and NextDent did not differ from one another (p = 0.9). The precision analysis shows that all tested groups had similar values, with no significant differences among them. Conclusion: The trueness values of the tested printing systems varied, although the precision values were similar. All evaluated printing systems achieved printing accuracy falling within the clinically acceptable range.

Knowledge of Saudi dental students and interns towards luting cements and their applications in fixed prosthodontics.

BACKGROUND: Enhancement of students' knowledge is essential in improving their clinical skills and performance. Thus, the curriculum should be prepared to achieve a better outcome. The current study aimed to determine the dental students' and interns' basic knowledge towards dental luting cements and their application in dental practice to improve the theoretical and clinical training sections. MATERIALS AND METHODS: A cross-sectional study was conducted among dental students and interns at three Colleges of Dentistry in the Kingdom of Saudi Arabia between September 2019-June 2020. An online questionnaire was used which included demographic data, questions about luting cement usage, cementation techniques, and commonly used cements in dental clinics. Descriptive analysis and chi-square test were used to show the association between level of dental education and the use of dental cements using SPSS software. The significance level was set at 5%. RESULTS: The total respondents were 626 dental students/interns of whom 78.8% were undergraduate dental students. Participants who reported undergraduate studies as the source of information were 79.7%. The type of restoration was the main factor in luting cement selection (62.6%). Concerning the isolation technique in cementing laminate veneers, 49.7% used dri-angles, cotton rolls and saliva ejectors. Dual-cure resin cement was the most common cement used in all the mentioned restorations except in pressed porcelain laminate veneers and cement-retained implant-supported restorations. CONCLUSIONS: Students' knowledge and practice in managing dental implants and porcelain laminate veneers need to be improved. The selection of a luting agent for a given restoration by students and interns was based on the basic knowledge, available cement, and the type of restoration. Awareness towards the management of short prepared teeth and custom-made cast posts and cores is also limited.

Denture Adhesive Utilization and Associated Factors among Dental Practitioners in the Eastern Province, Saudi Arabia.

BACKGROUND: Denture adhesives (DAs) enhance denture retention and stability, thus improving functions of removable prostheses. However, the adverse effects of DAs on denture foundation area were also reported. The clinical use of DAs among dentists has not been investigated in Saudi Arabia. Therefore, this study aimed to evaluate utilization of DAs and associated factors among dental practitioners in Saudi Arabia. METHODS: This cross-sectional study included dental professionals practicing in both public and private sectors in the Eastern Province of Saudi Arabia. A self-administered pilot tested questionnaire was distributed among participants. The questionnaire has questions related to demographic information, knowledge and awareness, and the utilization of DAs. Bivariate and multiple logistic regression analyses were performed. RESULTS: The study included 279 participants with a response rate of 79.03%. The majority of participants (61.6%) were below 35 years of age, males (56.6%), general dentists (57.3%), and worked in the private sector (59.9%). Less than half of the participants (39.4%) used DAs in their dental practice, and 64.5% recommended using DAs when needed. The most reported complications of DAs included inflammation (58.40%), ulcers (35.10%), and whitish color (31.20%) of denture foundation area. A vast majority (83.90%) reported that DAs improve retention of the dentures. About 55.2% of the participants were taught about DAs in their undergraduate programs, 12.5% attended continuing education, and 21.5% updated their knowledge about DAs. Multiple logistic regression showed that those who attended continuing education activities (adjusted OR = 2.41, p = 0.036) and updated their knowledge about DAs (adjusted OR = 4.43, p = < 0.001) were significantly more likely to use DAs in their dental practice. CONCLUSION: A minority of dental practitioners used DAs in their practices. Attending continuing education programs and updating knowledge of DAs were significantly associated with DAs utilization.

Scientific trends on research on denture stomatitis based on Scopus database: A bibliometric analysis.

Background: Denture stomatitis is a clinical condition that affects people who wear removable maxillary dentures. It causes redness, soreness, and erythema and ultimately affects the general condition of the patient. The objective of this study was to analyze the leading countries, journals, organizations, and authors and the frequently used keywords associated with denture stomatitis. Material and Methods: A bibliometric analysis of publications indexed in the Scopus database was conducted, and the article titles, abstracts, and keywords were analyzed using the VOSviewer software. Denture stomatitis-related publications from 1960 to 2021 were collected. This study included only research papers published in English with "article" as the paper type and dentistry as the subject area. Results: Data from a total of 461 articles and 10 different journals were obtained. The papers were published in 64 different countries. Brazil and the United States of America were the top contributing countries, and the University of Sydney was the leading organization. Papers published in the Journal of Oral Rehabilitation received the highest number of citations, while author Gordon Ramage from the University of Glasgow received the highest number of citations. Conclusions: The bibliometric analysis revealed that the number of denture stomatitis-related publications indexed in the Scopus database is increasing globally. Since 2007, there has been an increase in research interest regarding denture stomatitis, with more publications from several countries expected to be published in different journals. Key words:Bibliometric analysis, denture, candida, VOSviewer, maxilla.