Soft Perfusable Device to Culture Skeletal Muscle 3D Constructs in Air.

Devices for in vitro culture of three-dimensional (3D) skeletal muscle tissues have multiple applications, including tissue engineering and muscle-powered biorobotics. In both cases, it is crucial to recreate a biomimetic environment by using tailored scaffolds at multiple length scales and to administer prodifferentiative biophysical stimuli (e.g., mechanical loading). On the contrary, there is an increasing need to develop flexible biohybrid robotic devices capable of maintaining their functionality beyond laboratory settings. In this study, we describe a stretchable and perfusable device to sustain cell culture and maintenance in a 3D scaffold. The device mimics the structure of a muscle connected to two tendons: Tendon-Muscle-Tendon (TMT). The TMT device is composed of a soft (E ∼ 6 kPa) porous (pore diameter: ∼650 µm) polyurethane scaffold, encased within a compliant silicone membrane to prevent medium evaporation. Two tendon-like hollow channels interface the scaffold with a fluidic circuit and a stretching device. We report an optimized protocol to sustain C2C12 adhesion by coating the scaffold with polydopamine and fibronectin. Then, we show the procedure for the soft scaffold inclusion in the TMT device, demonstrating the device's ability to bear multiple cycles of elongations, simulating a protocol for cell mechanical stimulation. By using computational fluid dynamic simulations, we show that a flow rate of 0.62 mL/min ensures a wall shear stress value safe for cells (<2 Pa) and 50% of scaffold coverage by an optimal fluid velocity. Finally, we demonstrate the effectiveness of the TMT device to sustain cell viability under perfusion for 24 h outside of the CO2 incubator. We believe that the proposed TMT device can be considered an interesting platform to combine several biophysical stimuli, aimed at boosting skeletal muscle tissue differentiation in vitro, opening chances for the development of muscle-powered biohybrid soft robots with long-term operability in real-world environments.

Cell-free biomimetic polyurethane-based scaffold for breast reconstruction following non-malignant lesion resection. A first-in-human study.

BACKGROUND: Based on the volume of tissue removed, conservative surgery (BCS) cannot always guarantee satisfactory cosmetic results, unless resorting to more complex oncoplastic approaches. Investigating an alternative to optimize aesthetic outcomes minimizing surgical complexity, was the purpose of this study. We assessed an innovative surgical procedure based on the use of a biomimetic polyurethane-based scaffold intended for regenerating soft-tissue resembling fat, in patients undergoing BCS for non-malignant breast lesions. Safety and performance of the scaffold, and safety and feasibility of the entire implant procedure were evaluated. METHODS: A volunteer sample of 15 female patients underwent lumpectomy with immediate device positioning, performing seven study visits with six-month follow-up. We evaluated incidence of adverse events (AEs), changes in breast appearance (using photographs and anthropomorphic measurements), interference with ultrasound and MRI (assessed by two independent investigators), investigator's satisfaction (through a VAS scale), patient's pain (through a VAS scale) and quality of life (QoL) (using the BREAST-Q© questionnaire). Data reported are the results of the interim analysis on the first 5 patients. RESULTS: No AEs were device related nor serious. Breast appearance was unaltered and the device did not interference with imaging. High investigator's satisfaction, minimal post-operative pain and positive impact on QoL were also detected. CONCLUSIONS: Albeit on a limited number of patients, data showed positive outcomes both in terms of safety and performance, paving the way to an innovative breast reconstructive approach with a potential remarkable impact on clinical application of tissue engineering. TRIAL REGISTRATION: ClinicalTrials.gov (NCT04131972, October 18, 2019).

Monolithic Three-Dimensional Functionally Graded Hydrogels for Bioinspired Soft Robots Fabrication.

Bioinspired soft robotics aims at reproducing the complex hierarchy and architecture of biological tissues within artificial systems to achieve the typical motility and adaptability of living organisms. The development of suitable fabrication approaches to produce monolithic bodies provided with embedded variable morphological and mechanical properties, typically encountered in nature, is still a technological challenge. Here we report on a novel manufacturing approach to produce three-dimensional functionally graded hydrogels (3D-FGHs) provided with a controlled porosity gradient conferring them variable stiffness. 3D-FGHs are fabricated by means of a custom-designed liquid foam templating (LFT) technique, which relies on the inclusion of air bubbles generated by a blowing agent into the monomer-based template solution during ultraviolet-induced photopolymerization. The 3D-FGHs' apparent Young's modulus ranges from 0.37 MPa (bulky hydrogel region) to 0.09 MPa (highest porosity region). A fish-shaped soft swimmer is fabricated to demonstrate the feasibility of the LFT technique to produce bioinspired robots. Mobility tests show a significant improvement in terms of swimming speed when the robot is provided with a graded body. The proposed manufacturing approach constitutes an enabling solution for the development of macroscopic functionally graded hydrogel-based structures usable in biomimetic underwater soft robotics applications.

Effects of the 3D Geometry Reconstruction on the Estimation of 3D Porous Scaffold Permeability.

3D scaffolds for tissue engineering typically need to adopt a dynamic culture to foster cell distribution and survival throughout the scaffold. It is, therefore, crucial to know fluids' behavior inside the scaffold architecture, especially for complex porous ones. Here we report a comparison between simulated and measured permeability of a porous 3D scaffold, focusing on different modeling parameters. The scaffold features were extracted by microcomputed tomography (µCT) and representative volume elements were used for the computational fluid-dynamic analyses. The objective was to investigate the sensitivity of the model to the degree of detail of the µCT image and the elements of the mesh. These findings highlight the pros and cons of the modeling strategy adopted and the importance of such parameters in analyzing fluid behavior in 3D scaffolds.

Conditioning the microenvironment for soft tissue regeneration in a cell free scaffold.

The use of cell-free scaffolds for the regeneration of clinically relevant volumes of soft tissue has been challenged, particularly in the case of synthetic biomaterials, by the difficulty of reconciling the manufacturing and biological performance requirements. Here, we investigated in vivo the importance of biomechanical and biochemical cues for conditioning the 3D regenerative microenvironment towards soft tissue formation. In particular, we evaluated the adipogenesis changes related to 3D mechanical properties by creating a gradient of 3D microenvironments with different stiffnesses using 3D Poly(Urethane-Ester-ether) PUEt scaffolds. Our results showed a significant increase in adipose tissue proportions while decreasing the stiffness of the 3D mechanical microenvironment. This mechanical conditioning effect was also compared with biochemical manipulation by loading extracellular matrices (ECMs) with a PPAR-γ activating molecule. Notably, results showed mechanical and biochemical conditioning equivalency in promoting adipose tissue formation in the conditions tested, suggesting that adequate mechanical signaling could be sufficient to boost adipogenesis by influencing tissue remodeling. Overall, this work could open a new avenue in the design of synthetic 3D scaffolds for microenvironment conditioning towards the regeneration of large volumes of soft and adipose tissue, with practical and direct implications in reconstructive and cosmetic surgery.

Combined Effects of Electrical Stimulation and Protein Coatings on Myotube Formation in a Soft Porous Scaffold.

Compared to two-dimensional cell cultures, three-dimensional ones potentially allow recreating natural tissue environments with higher accuracy. The three-dimensional approach is being investigated in the field of tissue engineering targeting the reconstruction of various tissues, among which skeletal muscle. Skeletal muscle is an electroactive tissue which strongly relies upon interactions with the extracellular matrix for internal organization and mechanical function. Studying the optimization of myogenesis in vitro implies focusing on appropriate biomimetic stimuli, as biochemical and electrical ones. Here we present a three-dimensional polyurethane-based soft porous scaffold (porosity ~ 86%) with a Young's modulus in wet conditions close to the one of natural skeletal muscle tissue (~ 9 kPa). To study the effect of external stimuli on muscle cells, we functionalized the scaffold with extracellular matrix components (laminin and fibronectin) and observed an increase in myoblast proliferation over three days. Furthermore, the combination between laminin coating and electrical stimulation resulted in more spread and thicker myotubes compared to non-stimulated samples and samples receiving the single (non-combined) inputs. These results pave the way to the development of mature muscle tissue within three-dimensional soft scaffolds, through the combination of biochemical and electrical stimuli.

Decoration of RGD-mimetic porous scaffolds with engineered and devitalized extracellular matrix for adipose tissue regeneration.

Fat grafting is emerging as a promising alternative to silicon implants in breast reconstruction surgery. Unfortunately, this approach does not provide a proper mechanical support and is affected by drawbacks such as tissue resorption and donor site morbidity. Synthetic scaffolds can offer a valuable alternative to address these challenges, but poorly recapitulate the biochemical stimuli needed for tissue regeneration. Here, we aim at combining the positive features of a structural, synthetic polymer to an engineered, devitalized extracellular matrix (ECM) to generate a hybrid construct that can provide a mix of structural and biological stimuli needed for adipose tissue regeneration. A RGD-mimetic synthetic scaffold OPAAF, designed for soft tissue engineering, was decorated with ECM deposited by human adipose stromal cells (hASCs). The adipoinductive potential of the hybrid ECM-OPAAF construct was validated in vitro, by culture with hASC in a perfusion bioreactor system, and in vivo, by subcutaneous implantation in nude mouse. Our findings demonstrate that the hybrid ECM-OPAAF provides proper mechanical support and adipoinductive stimuli, with potential applicability as off-the-shelf material for adipose tissue reconstruction. STATEMENT OF SIGNIFICANCE: In this study we combined the functionalities of a synthetic polymer with those of an engineered and subsequently devitalized extracellular matrix (ECM) to generate a hybrid material for adipose tissue regeneration. The developed hybrid ECM-OPAAF was demonstrated to regulate human adipose stromal cells adipogenic commitment in vitro and adipose tissue infiltration in vivo. Our findings demonstrate that the hybrid ECM-OPAAF provide proper mechanical support and adipoinductive stimuli and represents a promising off-the-shelf material for adipose tissue reconstruction. We believe that our approach could offer an alternative strategy for adipose tissue reconstruction in case of mastectomy or congenital abnormalities, overcoming the current limitations of autologous fat based strategies such as volume resorption and donor site morbidity.

Exploring the potential of polyurethane-based soft foam as cell-free scaffold for soft tissue regeneration.

Reconstructive treatment after trauma and tumor resection would greatly benefit from an effective soft tissue regeneration. The use of cell-free scaffolds for adipose tissue regeneration in vivo is emerging as an attractive alternative to tissue-engineered constructs, since this approach avoids complications due to cell manipulation and lack of synchronous vascularization. In this study, we developed a biodegradable polyurethane-based scaffold for soft tissue regeneration, characterized by an exceptional combination between softness and resilience. Exploring the potential as a cell-free scaffold required profound understanding of the impact of its intrinsic physico-chemical properties on the biological performance in vivo. We investigated the effect of the scaffold's hydrophilic character, degradation kinetics, and internal morphology on (i) the local inflammatory response and activation of MGCs (foreign body response); (ii) its ability to promote rapid vascularisation, cell infiltration and migration through the scaffold over time; and (iii) the grade of maturation of the newly formed tissue into vascularized soft tissue in a murine model. The study revealed that soft tissue regeneration in vivo proceeded by gradual infiltration of undifferentiated mesenchymal cells though the periphery toward the center of the scaffold, where the rapid formation of a functional and well-formed vascular network supported cell viability overtime. STATEMENT OF SIGNIFICANCE: Exploring the potential of polyurethane-based soft foam as cell-free scaffold for soft tissue regeneration. In this work, we address the unmet need for synthetic functional soft tissue substitutes that provide adequate biological and mechanical support to soft tissue. We developed a series of flexible cross-linked polyurethane copolymer scaffolds with remarkable fatigue-resistance and tunable physico-chemical properties for soft tissue regeneration in vivo. Accordingly, we could extend the potential of this class of biomaterials, which was so far confined for bone and osteochondral tissue regeneration, to other types of connective tissue.

3D porous polyurethanes featured by different mechanical properties: Characterization and interaction with skeletal muscle cells.

The fabrication of biomaterials for interaction with muscle cells has attracted significant interest in the last decades. However, 3D porous scaffolds featured by a relatively low stiffness (almost matching the natural muscle one) and highly stable in response to cyclic loadings are not available at present, in this context. This work describes 3D polyurethane-based porous scaffolds featured by different mechanical properties. Biomaterial stiffness was finely tuned by varying the cross-linking degree of the starting foam. Compression tests revealed, for the softest material formulation, stiffness values close to the ones possessed by natural skeletal muscles. The materials were also characterized in terms of local nanoindenting, rheometric properties and long-term stability through cyclic compressions, in a strain range reflecting the contraction extent of natural muscles. Preliminary in vitro tests revealed a preferential adhesion of C2C12 skeletal muscle cells over the softer, rougher and more porous structures. All the material formulations showed low cytotoxicity.

An Injectable System for Local and Sustained Release of Antimicrobial Agents in the Periodontal Pocket.

Periodontitis treatments usually require local administration of antimicrobial drugs with the aim to reduce the bacterial load inside the periodontal pocket. Effective pharmaceutical treatments may require sustained local drug release for several days in the site of interest. Currently available solutions are still not able to fulfill the clinical need for high-quality treatments, mainly in terms of release profiles and patients' comfort. This work aims to fill this gap through the development of an in situ gelling system, capable to achieve controlled and sustained release of antimicrobial agents for medium-to-long-term treatments. The system is composed of micrometer-sized ß-cyclodextrin-based hydrogel (bCD-Jef-MPs), featured by a strong hydrophilic character, suspended in a synthetic block-co-polymer solution (Poloxamer 407), which is capable to undergo rapid thermally induced sol-gel phase transition at body temperature. The chemical structure of bCD-Jef-MPs was confirmed by cross-correlating data from Fourier transform infrared (FTIR) spectroscopy, swelling test, and degradation kinetics. The thermally induced sol-gel phase transition is demonstrated by rheometric tests. The effectiveness of the described system to achieve sustained release of antimicrobial agents is demonstrated in vitro, using chlorhexidine digluconate as a drug model. The results achieved in this work disclose the potential of the mentioned system in effectively treating periodontitis lesions.

Calcium Stearate as an Effective Alternative to Poly(vinyl alcohol) in Poly-Lactic-co-Glycolic Acid Nanoparticles Synthesis.

Poly(d,l-lactic-co-glycolic acid) (PLGA) nanoparticles (NPs) are among the most studied systems for drug and gene targeting. So far, the synthesis of stable and uniform PLGA NPs has involved the use of a large excess of polyvinyl surfactants such as poly(vinyl alcohol) (PVA) and polyvinylpyrrolidone (PVP), whose removal requires multistep purification procedures of high ecological and economic impact. Hence the development of environment-friendly and cost-effective synthetic procedures for the synthesis of PLGA NPs would effectively boost their use in clinics. This work aims to address this issue by investigating more efficacious alternatives to the so far employed polyvinyl surfactants. More specifically, we developed an innovative synthetic process to achieve stable and uniformly distributed PLGA NPs that involves the use of calcium stearate (CSt), gaining benefits of its high biocompatibility and efficacy at low concentrations and avoiding consequently expensive purification steps. With the help of minimum quantities of polysorbate 60 and sorbitane monostearate, CSt-stabilized PLGA NPs with different sizes and structures were synthesized. The influence of CSt on the encapsulation efficiency of bioactive molecules has been also investigated. The effective encapsulation of both hydrophobic (curcumin) and hydrophilic (fibrinogen labeled with Alexa647) biomolecules into NPs was demonstrated by confocal microscopy, and their release quantified by spectrofluorimetric analyses. Finally, degradation and cytotoxicity studies showed that CSt stabilized NPs were stable under physiological conditions and with good biocompatibility, thus looking promising for further investigation as controlled release devices.

Photocrosslinked poly(amidoamine) nanoparticles for central nervous system targeting.

This study presents an innovative method for the synthesis of polymeric nanoparticles (NPs) for central nervous system (CNS) targeting. The method is based on Ultraviolet light (UV)-induced crosslinking of diacrylamide-terminated oligomers of poly(amidoamine)s (PAAs), a widely used class of synthetic polymers in biomedical field research, especially in drug delivery thanks to their excellent biocompatibility and controlled biodegradability. Previous attempts aiming at preparing PAA-based NPs by self-assembly were challenged by lack of structural stability and consequently their early degradation and premature drug release. Here, the UV-induced crosslinked PAA NPs demonstrated to overcome main disadvantages of the self-assembled ones, as they showed improved stability and controlled release properties. Besides the remarkable efficiency to produce monodisperse and stable PAA NPs, the UV-induced crosslinking method is featured by great versatility and low environmental impact, since it does not require use of organic solvents and multiple purification steps. The capability of PAA NPs to encapsulate a fluorescently labelled model protein was experimentally demonstrated in this study. Cell culture experiments showed that PAA NPs were biocompatible and highly permeable across an in vitro blood-brain barrier model, thus highlighting their great potential as drug delivery vectors for CNS delivery.

Stem Cell Delivery With Polymer Hydrogel for Treatment of Intervertebral Disc Degeneration: From 3D Culture to Design of the Delivery Device for Minimally Invasive Therapy.

Nucleus pulposus (NP) tissue damage can induce detrimental mechanical strain on the biomechanical performance of intervertebral discs (IVDs), causing subsequent disc degeneration. A novel, photocurable, injectable, synthetic polymer hydrogel (pHEMA-co-APMA grafted with PAA) has already demonstrated success in encapsulating and differentiating human mesenchymal stem cells (hMSCs) toward an NP phenotype during hypoxic conditions. After demonstration of promising results in our previous work, in this study we have further investigated the inclusion of mechanical stimulation and its impact on hMSC differentiation toward an NP phenotype through the characterization of matrix markers such as SOX-9, aggrecan, and collagen II. Furthermore, investigations were undertaken in order to approximate delivery parameters for an injection delivery device, which could be used to transport hMSCs suspended in hydrogel into the IVD. hMSC-laden hydrogel solutions were injected through various needle gauge sizes in order to determine its impact on postinjection cell viability and IVD tissue penetration. Interpretation of these data informed the design of a potential minimally invasive injection device, which could successfully inject hMSCs encapsulated in a UV-curable polymer into NP, prior to photo-cross-linking in situ.

Biologically and mechanically driven design of an RGD-mimetic macroporous foam for adipose tissue engineering applications.

Despite clinical treatments for adipose tissue defects, in particular breast tissue reconstruction, have certain grades of efficacy, many drawbacks are still affecting the long-term survival of new formed fat tissue. To overcome this problem, in the last decades, several scaffolding materials have been investigated in the field of adipose tissue engineering. However, a strategy able to recapitulate a suitable environment for adipose tissue reconstruction and maintenance is still missing. To address this need, we adopted a biologically and mechanically driven design to fabricate an RGD-mimetic poly(amidoamine) oligomer macroporous foam (OPAAF) for adipose tissue reconstruction. The scaffold was designed to fulfil three fundamental criteria: capability to induce cell adhesion and proliferation, support of in vivo vascularization and match of native tissue mechanical properties. Poly(amidoamine) oligomers were formed into soft scaffolds with hierarchical porosity through a combined free radical polymerization and foaming reaction. OPAAF is characterized by a high water uptake capacity, progressive degradation kinetics and ideal mechanical properties for adipose tissue reconstruction. OPAAF's ability to support cell adhesion, proliferation and adipogenesis was assessed in vitro using epithelial, fibroblast and endothelial cells (MDCK, 3T3L1 and HUVEC respectively). In addition, in vivo subcutaneous implantation in murine model highlighted OPAAF potential to support both adipogenesis and vessels infiltration. Overall, the reported results support the use of OPAAF as a scaffold for engineered adipose tissue construct.

A Tailor-Made Synthetic Polymer for Cell Encapsulation: Design Rationale, Synthesis, Chemical-Physics and Biological Characterizations.

This study presents a custom-made in situ gelling polymeric precursor for cell encapsulation. Composed of poly((2-hydroxyethyl)methacrylate-co-(3-aminopropyl)methacrylamide) (P(HEMA-co-APM) mother backbone and RGD-mimicking poly(amidoamine) (PAA) moiteis, the comb-like structured polymeric precursor is tailored to gather the advantages of the two families of synthetic polymers, i.e., the good mechanical integrity of PHEMA-based polymers and the biocompatibility and biodegradability of PAAs. The role of P(HEMA-co-APM) in the regulation of the chemico-physical properties of P(HEMA-co-APM)/PAA hydrogels is thoroughly investigated. On the basis of obtained results, namely the capability of maintaining vital NIH3T3 cell line in vitro for 2 d in a 3D cell culture, the in vivo biocompatibility in murine model for 16 d, and the ability of finely tuning mechanical properties and degradation kinetics, it can be assessed that P(HEMA-co-APM)/PAAs offer a cost-effective valid alternative to the so far studied natural polymer-based systems for cell encapsulation.

In vivo imaging study of angiogenesis in a channelized porous scaffold.

The main scientific issue hindering the development of tissue engineering technologies is the lack of proper vascularization. Among the various approaches developed for boosting vascularization, scaffold design has attracted increasing interest over the last few years. The aim of this article is to illustrate a scaffold design strategy for enhancing vascularization based on sacrificial microfabrication of embedded microchannels. This approach was combined with an innovative poly(ether urethane urea) (PEUtU) porous scaffold to provide an alternative graft substitute material for the treatment of tissue defects. Fluorescent and chemiluminescent imaging combined with computed tomography were used to study the behavior of the scaffold composition within living subjects by analyzing angiogenesis and inflammation processes and observing the variation in x-ray absorption, respectively. For this purpose, an IntegriSense 680 probe was used in vivo for the localization and quantification of integrin αvß3, due to its critical involvement in angiogenesis, and a XenoLight RediJect Inflammation Probe for the study of the decline in inflammation progression during healing. Overall, the collected data suggest the advantages of embedding a synthetic vascular network into a PEUtU porous matrix to enhance in vivo tissue integration, maturation, and regeneration. Moreover, our imaging approach proved to be an efficient and versatile tool for scaffold in vivo testing.

RGD-mimetic poly(amidoamine) hydrogel for the fabrication of complex cell-laden micro constructs.

The potential of the 3D cell culture approach for creating in vitro models for drug screening and cellular studies, has led to the development of hydrogels that are able to mimic the in vivo 3D cellular milieu. To this aim, synthetic polymer-based hydrogels, with which it is possible to fine-tune the chemical and biophysical properties of the cell microenvironment, are becoming more and more acclaimed. Of all synthetic materials, poly(amidoamine)s (PAAs) hydrogels are known to have promising properties. In particular, PAAs hydrogels containing the 2,2-bisacrylamidoacetic acid-agmatine monomeric unit are capable of enhancing cellular adhesion by interacting with the RGD-binding αVß3 integrin. The synthesis of a new photocrosslinkable, biomimetic PAA-Jeffamine®-PAA triblock copolymer (PJP) hydrogel is reported in this paper with the aim of improving the optical, biocompatibility and cell-adhesion properties of previously studied PAA hydrogels and providing an inexpensive alternative to the RGD peptide based hydrogels. The physicochemical properties of PJP hydrogels are extensively discussed and the behavior of 2D and 3D cell cultures was analyzed in depth with different cell types. Moreover, cell-laden PJP hydrogels were patterned with perfusable microchannels and seeded with endothelial cells, in order to investigate the possibility of using PJP hydrogels for fabricating cell laden tissue-like micro constructs and microfluidic devices. Overall the data obtained suggest that PJP could ultimately become a useful tool for fabricating improved in vitro models in order to potentially enhance the effectiveness of drug screening and clinical treatments.

Versatile fabrication of vascularizable scaffolds for large tissue engineering in bioreactor.

Despite significant progresses were achieved in tissue engineering over the last 20 years, a number of unsolved problems still remain. One of the most relevant issues is the lack of a proper vascularization that is limiting the size of the engineered tissues to smaller than clinically relevant dimensions. Sacrificial molding holds great promise to engineered construct with perfusable vascular architectures, but there is still the need to develop more versatile approaches able to be independent of the nature and dimensions of the construct. In this work we developed a versatile sacrificial molding technique for fabricating bulk, cell-laden and porous scaffolds with embedded vascular fluidic networks. These branched fluidic architectures are created by highly resistant thermoplastic sacrificial templates, made of poly(vinyl alcohol), representing a remarkable progress in manufacturability and scalability. The obtained architecture, when perfused in bioreactor, has shown to prevent the formation of a necrotic core in thick cell-laden constructs and enabled the rapid fabrication of hierarchically branched endothelium. In conclusion we demonstrate a novel strategy towards the engineering of vascularized thick tissues through the integration of the PVA-based microfabrication sacrificial approach and perfusion bioreactors. This approach may be able to scale current engineered tissues to clinically relevant dimensions, opening the way to their widespread clinical applications.

Three-dimensional hypoxic culture of human mesenchymal stem cells encapsulated in a photocurable, biodegradable polymer hydrogel: a potential injectable cellular product for nucleus pulposus regeneration.

Nucleus pulposus (NP) tissue damage can induce detrimental mechanical stresses and strains on the intervertebral disc, leading to disc degeneration. This study demonstrates the potential of a novel, photo-curable, injectable, synthetic polymer hydrogel (pHEMA-co-APMA grafted with polyamidoamine (PAA)) to encapsulate and differentiate human mesenchymal stem cells (hMSC) towards a NP phenotype under hypoxic conditions which could be used to restore NP tissue function and mechanical properties. Encapsulated hMSC cultured in media (hMSC and chondrogenic) displayed good cell viability up to day 14. The genotoxicity effects of ultraviolet (UV) on hMSC activity confirmed the acceptability of 2.5min of UV light exposure to cells. Cytotoxicity investigations revealed that hMSC cultured in media containing p(HEMA-co-APMA) grafted with PAA degradation product (10% and 20%v/v concentration) for 14days significantly decreased the initial hMSC adhesion ability and proliferation rate from 24hrs to day 14. Successful differentiation of encapsulated hMSC within hydrogels towards chondrogenesis was observed with elevated expression levels of aggrecan and collagen II when cultured in chondrogenic media under hypoxic conditions, in comparison with culture in hMSC media for 14days. Characterization of the mechanical properties revealed a significant decrease in stiffness and modulus values of cellular hydrogels in comparison with acellular hydrogels at both day 7 and day 14. These results demonstrate the potential use of an in vivo photo-curable injectable, synthetic hydrogel with encapsulated hMSC for application in the repair and regeneration of NP tissue.

Poly(amido-amine)-based hydrogels with tailored mechanical properties and degradation rates for tissue engineering.

Poly(amido-amine) (PAA) hydrogels containing the 2,2-bisacrylamidoacetic acid-4-amminobutyl guanidine monomeric unit have a known ability to enhance cellular adhesion by interacting with the arginin-glycin-aspartic acid (RGD)-binding αVß3 integrin, expressed by a wide number of cell types. Scientific interest in this class of materials has traditionally been hampered by their poor mechanical properties and restricted range of degradation rate. Here we present the design of novel biocompatible, RGD-mimic PAA-based hydrogels with wide and tunable degradation rates as well as improved mechanical and biological properties for biomedical applications. This is achieved by radical polymerization of acrylamide-terminated PAA oligomers in both the presence and absence of 2-hydroxyethylmethacrylate. The degradation rate is found to be precisely tunable by adjusting the PAA oligomer molecular weight and acrylic co-monomer concentration in the starting reaction mixture. Cell adhesion and proliferation tests on Madin-Darby canine kidney epithelial cells show that PAA-based hydrogels have the capacity to promote cell adhesion up to 200% compared to the control. Mechanical tests show higher compressive strength of acrylic chain containing hydrogels compared to traditional PAA hydrogels.