Latest developments in nanofluid flow and heat transfer between parallel surfaces: A critical review.

The enhancement of heat transfer between parallel surfaces, including parallel plates, parallel disks, and two concentric pipes, is vital because of their wide applications ranging from lubrication systems to water purification processes. Various techniques can be utilized to enhance heat transfer in such systems. Adding nanoparticles to the conventional working fluids is an effective solution that could remarkably enhance the heat transfer rate. No published review article focuses on the recent advances in nanofluid flow between parallel surfaces; therefore, the present paper aims to review the latest experimental and numerical studies on the flow and heat transfer of nanofluids (mixtures of nanoparticles and conventional working fluids) in such configurations. For the performance analysis of thermal systems composed of parallel surfaces and operating with nanofluids, it is necessary to know the physical phenomena and parameters that influence the flow and heat transfer characteristics in these systems. Significant results obtained from this review indicate that, in most cases, the heat transfer rate between parallel surfaces is enhanced with an increase in the Rayleigh number, the Reynolds number, the magnetic number, and Brownian motion. On the other hand, an increase in thermophoresis parameter, as well as flow parameters, including the Eckert number, buoyancy ratio, Hartmann number, and Lewis number, leads to heat transfer rate reduction.

Impact of two-phase hybrid nanofluid approach on mixed convection inside wavy lid-driven cavity having localized solid block.

INTRODUCTION: Mixed convection flow and heat transfer within various cavities including lid-driven walls has many engineering applications. Investigation of such a problem is important in enhancing the performance of the cooling of electric, electronic and nuclear devices and controlling the fluid flow and heat exchange of the solar thermal operations and thermal storage. OBJECTIVES: The main aim of this fundamental investigation is to examine the influence of a two-phase hybrid nanofluid approach on mixed convection characteristics including the consequences of varying Richardson number, number of oscillations, nanoparticle volume fraction, and dimensionless length and dimensionless position of the solid obstacle. METHODS: The migration of composite hybrid nanoparticles due to the nano-scale forces of the Brownian motion and thermophoresis was taken into account. There is an inner block near the middle of the enclosure, which contributes toward the flow, heat, and mass transfer. The top lid cover wall of the enclosure is allowed to move which induces a mixed convection flow. The impact of the migration of hybrid nanoparticles with regard to heat transfer is also conveyed in the conservation of energy. The governing equations are molded into the non-dimensional pattern and then explained using the finite element technique. The effect of various non-dimensional parameters such as the volume fraction of nanoparticles, the wave number of walls, and the Richardson number on the heat transfer and the concentration distribution of nanoparticles are examined. Various case studies for Al2O3-Cu/water hybrid nanofluids are performed. RESULTS: The results reveal that the temperature gradient could induce a notable concentration variation in the enclosure. CONCLUSION: The location of the solid block and undulation of surfaces are valuable in the control of the heat transfer and the concentration distribution of the composite nanoparticles.

Optimum Placement of Heating Tubes in a Multi-Tube Latent Heat Thermal Energy Storage.

Utilizing phase change materials in thermal energy storage systems is commonly considered as an alternative solution for the effective use of energy. This study presents numerical simulations of the charging process for a multitube latent heat thermal energy storage system. A thermal energy storage model, consisting of five tubes of heat transfer fluids, was investigated using Rubitherm phase change material (RT35) as the. The locations of the tubes were optimized by applying the Taguchi method. The thermal behavior of the unit was evaluated by considering the liquid fraction graphs, streamlines, and isotherm contours. The numerical model was first verified compared with existed experimental data from the literature. The outcomes revealed that based on the Taguchi method, the first row of the heat transfer fluid tubes should be located at the lowest possible area while the other tubes should be spread consistently in the enclosure. The charging rate changed by 76% when varying the locations of the tubes in the enclosure to the optimum point. The development of streamlines and free-convection flow circulation was found to impact the system design significantly. The Taguchi method could efficiently assign the optimum design of the system with few simulations. Accordingly, this approach gives the impression of the future design of energy storage systems.

Thermal Energy Storage and Heat Transfer of Nano-Enhanced Phase Change Material (NePCM) in a Shell and Tube Thermal Energy Storage (TES) Unit with a Partial Layer of Eccentric Copper Foam.

Thermal energy storage units conventionally have the drawback of slow charging response. Thus, heat transfer enhancement techniques are required to reduce charging time. Using nanoadditives is a promising approach to enhance the heat transfer and energy storage response time of materials that store heat by undergoing a reversible phase change, so-called phase change materials. In the present study, a combination of such materials enhanced with the addition of nanometer-scale graphene oxide particles (called nano-enhanced phase change materials) and a layer of a copper foam is proposed to improve the thermal performance of a shell-and-tube latent heat thermal energy storage (LHTES) unit filled with capric acid. Both graphene oxide and copper nanoparticles were tested as the nanometer-scale additives. A geometrically nonuniform layer of copper foam was placed over the hot tube inside the unit. The metal foam layer can improve heat transfer with an increase of the composite thermal conductivity. However, it suppressed the natural convection flows and could reduce heat transfer in the molten regions. Thus, a metal foam layer with a nonuniform shape can maximize thermal conductivity in conduction-dominant regions and minimize its adverse impacts on natural convection flows. The heat transfer was modeled using partial differential equations for conservations of momentum and heat. The finite element method was used to solve the partial differential equations. A backward differential formula was used to control the accuracy and convergence of the solution automatically. Mesh adaptation was applied to increase the mesh resolution at the interface between phases and improve the quality and stability of the solution. The impact of the eccentricity and porosity of the metal foam layer and the volume fraction of nanoparticles on the energy storage and the thermal performance of the LHTES unit was addressed. The layer of the metal foam notably improves the response time of the LHTES unit, and a 10% eccentricity of the porous layer toward the bottom improved the response time of the LHTES unit by 50%. The presence of nanoadditives could reduce the response time (melting time) of the LHTES unit by 12%, and copper nanoparticles were slightly better than graphene oxide particles in terms of heat transfer enhancement. The design parameters of the eccentricity, porosity, and volume fraction of nanoparticles had minimal impact on the thermal energy storage capacity of the LHTES unit, while their impact on the melting time (response time) was significant. Thus, a combination of the enhancement method could practically reduce the thermal charging time of an LHTES unit without a significant increase in its size.

Thermal Charging Optimization of a Wavy-Shaped Nano-Enhanced Thermal Storage Unit.

A wavy shape was used to enhance the thermal heat transfer in a shell-tube latent heat thermal energy storage (LHTES) unit. The thermal storage unit was filled with CuO-coconut oil nano-enhanced phase change material (NePCM). The enthalpy-porosity approach was employed to model the phase change heat transfer in the presence of natural convection effects in the molten NePCM. The finite element method was applied to integrate the governing equations for fluid motion and phase change heat transfer. The impact of wave amplitude and wave number of the heated tube, as well as the volume concertation of nanoparticles on the full-charging time of the LHTES unit, was addressed. The Taguchi optimization method was used to find an optimum design of the LHTES unit. The results showed that an increase in the volume fraction of nanoparticles reduces the charging time. Moreover, the waviness of the tube resists the natural convection flow circulation in the phase change domain and could increase the charging time.

The Thermal Charging Performance of Finned Conical Thermal Storage System Filled with Nano-Enhanced Phase Change Material.

A latent heat thermal energy storage (LHTES) unit can store a notable amount of heat in a compact volume. However, the charging time could be tediously long due to weak heat transfer. Thus, an improvement of heat transfer and a reduction in charging time is an essential task. The present research aims to improve the thermal charging of a conical shell-tube LHTES unit by optimizing the shell-shape and fin-inclination angle in the presence of nanoadditives. The governing equations for the natural convection heat transfer and phase change heat transfer are written as partial differential equations. The finite element method is applied to solve the equations numerically. The Taguchi optimization approach is then invoked to optimize the fin-inclination angle, shell aspect ratio, and the type and volume fraction of nanoparticles. The results showed that the shell-aspect ratio and fin inclination angle are the most important design parameters influencing the charging time. The charging time could be changed by 40% by variation of design parameters. Interestingly a conical shell with a small radius at the bottom and a large radius at the top (small aspect ratio) is the best shell design. However, a too-small aspect ratio could entrap the liquid-PCM between fins and increase the charging time. An optimum volume fraction of 4% is found for nanoparticle concentration.

Melting phase change heat transfer in a quasi-petal tube thermal energy storage unit.

In the present study, the thermal energy storage of a hot petal tube inside a shell-tube type Thermal Energy Storage (TES) unit was addressed. The shell is filled with the capric acid Phase Change Material (PCM) and absorbs the heat from a hot U-tube petal. The governing equations for the natural convection flow of molten PCM and phase change heat transfer were introduced by using the enthalpy-porosity approach. An automatic adaptive mesh scheme was used to track the melting interface. The accuracy and convergence of numerical computations were also controlled by a free step Backward Differentiation Formula. The modeling results were compared with previous experimental data. It was found that the present adaptive mesh approach can adequately the melting heat transfer, and an excellent agreement was found with available literature. The effect of geometrical designs of the petal tube was investigated on the melting response of the thermal energy storage unit. The phase change behavior was analyzed by using temperature distribution contours. The results showed that petal tubes could notably increase the melting rate in the TES unit compared to a typical circular tube. Besides, the more the petal numbers, the better the heat transfer. Using a petal tube could increase the charging power by 44% compared to a circular tube. The placement angle of the tubes is another important design factor which should be selected carefully. For instance, vertical placement of tubes could improve the charging power by 300% compared to a case with the tubes' horizontal placement.

Phase-Transition Thermal Charging of a Channel-Shape Thermal Energy Storage Unit: Taguchi Optimization Approach and Copper Foam Inserts.

Thermal energy storage is a technique that has the potential to contribute to future energy grids to reduce fluctuations in supply from renewable energy sources. The principle of energy storage is to drive an endothermic phase change when excess energy is available and to allow the phase change to reverse and release heat when energy demand exceeds supply. Unwanted charge leakage and low heat transfer rates can limit the effectiveness of the units, but both of these problems can be mitigated by incorporating a metal foam into the design of the storage unit. This study demonstrates the benefits of adding copper foam into a thermal energy storage unit based on capric acid enhanced by copper nanoparticles. The volume fraction of nanoparticles and the location and porosity of the foam were optimized using the Taguchi approach to minimize the charge leakage expected from simulations. Placing the foam layer at the bottom of the unit with the maximum possible height and minimum porosity led to the lowest charge time. The optimum concentration of nanoparticles was found to be 4 vol.%, while the maximu possible concentration was 6 vol.%. The use of an optimized design of the enclosure and the optimum fraction of nanoparticles led to a predicted charging time for the unit that was approximately 58% shorter than that of the worst design. A sensitivity analysis shows that the height of the foam layer and its porosity are the dominant variables, and the location of the porous layer and volume fraction of nanoparticles are of secondary importance. Therefore, a well-designed location and size of a metal foam layer could be used to improve the charging speed of thermal energy storage units significantly. In such designs, the porosity and the placement-location of the foam should be considered more strongly than other factors.

Phase Change Process in a Zigzag Plate Latent Heat Storage System during Melting and Solidification.

Applying a well-performing heat exchanger is an efficient way to fortify the relatively low thermal response of phase-change materials (PCMs), which have broad application prospects in the fields of thermal management and energy storage. In this study, an improved PCM melting and solidification in corrugated (zigzag) plate heat exchanger are numerically examined compared with smooth (flat) plate heat exchanger in both horizontal and vertical positions. The effects of the channel width (0.5 W, W, and 2 W) and the airflow temperature (318 K, 323 K, and 328 K) are exclusively studied and reported. The results reveal the much better performance of the horizontal corrugated configuration compared with the smooth channel during both melting and solidification modes. It is found that the melting rate is about 8% faster, and the average temperature is 4 K higher in the corrugated region compared with the smooth region because of the large heat-exchange surface area, which facilitates higher rates of heat transfer into the PCM channel. In addition to the higher performance, a more compact unit can be achieved using the corrugated system. Moreover, applying the half-width PCM channel accelerates the melting rate by eight times compared to the double-width channel. Meanwhile, applying thicker channels provides faster solidification rates. The melting rate is proportional to the airflow temperature. The PCM melts within 274 s when the airflow temperature is 328 K. However, the melting time increases to 460 s for the airflow temperature of 308 K. Moreover, the PCM solidifies in 250 s and 405 s in the cases of 318 K and 328 K airflow temperatures, respectively.

Role of Rotating Cylinder toward Mixed Convection inside a Wavy Heated Cavity via Two-Phase Nanofluid Concept.

The mixed convection two-phase flow and heat transfer of nanofluids were addressed within a wavy wall enclosure containing a solid rotating cylinder. The annulus area between the cylinder and the enclosure was filled with water-alumina nanofluid. Buongiorno's model was applied to assess the local distribution of nanoparticles in the host fluid. The governing equations for the mass conservation of nanofluid, nanoparticles, and energy conservation in the nanofluid and the rotating cylinder were carried out and converted to a non-dimensional pattern. The finite element technique was utilized for solving the equations numerically. The influence of the undulations, Richardson number, the volume fraction of nanoparticles, rotation direction, and the size of the rotating cylinder were examined on the streamlines, heat transfer rate, and the distribution of nanoparticles. The Brownian motion and thermophoresis forces induced a notable distribution of nanoparticles in the enclosure. The best heat transfer rate was observed for 3% volume fraction of alumina nanoparticles. The optimum number of undulations for the best heat transfer rate depends on the rotation direction of the cylinder. In the case of counterclockwise rotation of the cylinder, a single undulation leads to the best heat transfer rate for nanoparticles volume fraction about 3%. The increase of undulations number traps more nanoparticles near the wavy surface.

Free convection of a suspension containing nano-encapsulated phase change material in a porous cavity; local thermal non-equilibrium model.

Due to the instinctive temperature-dependent heat capacity of the Nano-Encapsulated Phase Change Material (NEPCM), there is a growing interest in the potential applications of such materials in heat transfer. As such, steady-state natural convection in a porous enclosure saturated with nanofluid using NEPCMs has been investigated in this study. The cavity is assumed to have constant hot and cold temperatures at the left and right vertical boundaries, respectively, and fully insulated from the bottom and top walls. Considering the Local Thermal Non-equilibrium (LTNE) approach for the porous structure, the governing equations are first non-dimensionalized and then solved by employing the finite element Galerkin method. The impact of different parameters, such as porous thermal conductivity (k s ), solid-fluid interface heat transfer (10 ≤ H ≤ 105), Stefan number (0.2 ≤ Ste ≤ 1), and volume fraction of nanoparticles (0.0 ≤ φ ≤ 0.05) on the patterns of the fluid and solid isotherms, streamlines and the contours of the heat capacity ratio, fusion temperature (0.05 ≤ θ f ≤ 1), local and average Nusselt numbers, and overall heat transfer ratio has been studied. It is shown that improving the porous thermal conductivity not only leads to an increase in the rate of heat transfer but also augments the fluid flow inside the cavity. For low values of the Ste, the rate of heat, transferred in the porous enclosure, is intensified. However, regardless of the amount of the Stefan number, the maximum rate of heat transfer is achievable when the non-dimensional fusion temperature is approximately 0.5. Employing NEPCMs in a highly conductive porous structure is more efficacious only when the phases are in the state of local thermal equilibrium. Nonetheless, the rate of heat transfer is higher when the Local thermal non-equilibrium is validated between the phases. Besides, for poor thermal conductivity of the porous medium like glass balls (LTE condition), adding 5% of the nano-encapsulated phase change materials to pure water can boost the rate of heat transfer up to 47% (for Ste = 0.2 and θ f = 0.5). This thermal investigation of NEPCMs shows in detail how advantageous are these nanoparticles in heat transfer and opens up an avenue for further application-based studies.

Numerical Modeling and Investigation of Amperometric Biosensors with Perforated Membranes.

The present paper aims to investigate the influence of perforated membrane geometry on the performance of biosensors. For this purpose, a 2-D axisymmetric model of an amperometric biosensor is analyzed. The governing equations describing the reaction-diffusion equations containing a nonlinear term related to the Michaelis-Menten kinetics of the enzymatic reaction are introduced. The partial differential governing equations, along with the boundary conditions, are first non-dimensionalized by using appropriate dimensionless variables and then solved in a non-uniform unstructured grid by employing the Galerkin Finite Element Method. To examine the impact of the hole-geometry of the perforated membrane, seven different geometries-including cylindrical, upward circular cone, downward circular cone, upward paraboloid, downward paraboloid, upward concave paraboloid, and downward concave paraboloid-are studied. Moreover, the effects of the perforation level of the perforated membrane, the filling level of the enzyme on the transient and steady-state current of the biosensor, and the half-time response are presented. The results of the simulations show that the transient and steady-state current of the biosensor are affected by the geometry dramatically. Thus, the sensitivity of the biosensor can be influenced by different hole-geometries. The minimum and maximum output current can be obtained from the cylindrical and upward concave paraboloid holes. On the other hand, the least half-time response of the biosensor can be obtained in the cylindrical geometry.

Free convection in a parallelogrammic porous cavity filled with a nanofluid using Tiwari and Das' nanofluid model.

The free convection heat transfer of Cu-water nanofluids in a parallelogrammic enclosure filled with porous media is numerically analyzed. The bottom and top of the enclosure are insulated while the sidewalls are subject to limited temperature difference. The Darcy flow and the Tiwari and Das' nanofluid models are considered. The governing dimensionless partial differential equations are numerically solved using a finite difference code. The results are reported for isotherms and streamlines as well as Nusselt number as a function of the volume fraction of nanoparticles, porosity, types of the porous matrix, inclination angle, aspect ratio and different Rayleigh numbers. It is found that the presence of the nanoparticles inside the enclosure deteriorates the heat transfer rate, which is caused due to the increase of dynamic viscosity by the presence of nanoparticles. Therefore, in applications in which the nanofluids are used for their advantages, such as enhanced dielectric properties or antibacterial properties, more caution for the heat transfer design of the enclosure is necessary.