Correction to "Interfacial Chemistry in the Electrocatalytic Hydrogenation of CO2 over C-Supported Cu-Based Systems".

[This corrects the article DOI: 10.1021/acscatal.3c01288.].

Atomically dispersed asymmetric cobalt electrocatalyst for efficient hydrogen peroxide production in neutral media.

Electrochemical hydrogen peroxide (H2O2) production (EHPP) via a two-electron oxygen reduction reaction (2e- ORR) provides a promising alternative to replace the energy-intensive anthraquinone process. M-N-C electrocatalysts, which consist of atomically dispersed transition metals and nitrogen-doped carbon, have demonstrated considerable EHPP efficiency. However, their full potential, particularly regarding the correlation between structural configurations and performances in neutral media, remains underexplored. Herein, a series of ultralow metal-loading M-N-C electrocatalysts are synthesized and investigated for the EHPP process in the neutral electrolyte. CoNCB material with the asymmetric Co-C/N/O configuration exhibits the highest EHPP activity and selectivity among various as-prepared M-N-C electrocatalyst, with an outstanding mass activity (6.1 × 105 A gCo-1 at 0.5 V vs. RHE), and a high practical H2O2 production rate (4.72 mol gcatalyst-1 h-1 cm-2). Compared with the popularly recognized square-planar symmetric Co-N4 configuration, the superiority of asymmetric Co-C/N/O configurations is elucidated by X-ray absorption fine structure spectroscopy analysis and computational studies.

Enhancing Nitrogen Reduction Reaction through Formation of 2D/2D Hybrid Heterostructures of MoS2@rGO.

Given the challenging task of constructing an efficient nitrogen reduction reaction (NRR) electrocatalyst with enhanced ambient condition performance, properties such as high specific surface area, fast electron transfer, and design of the catalyst surface constitute a group of key factors to be taken into consideration to guarantee outstanding catalytic performance and durability. Thereof, this work investigates the contribution of the 2D/2D heterojunction interface between MoS2 and reduced graphene oxide (rGO) on the electrocatalytic synthesis of NH3 in an alkaline media. The results revealed remarkable NRR performance on the MoS2@rGO 2D/2D hybrid electrocatalyst, characterized by a high NRR sensitivity (faradaic efficiency) of 34.7% with an NH3 yield rate of 3.98 ± 0.19 mg h-1 cm-2 at an overpotential of -0.3 V vs RHE in 0.1 M KOH solution. The hybrid electrocatalysts also exhibited selectivity for NH3 synthesis against the production of the hydrazine (N2H4) byproduct, hindrance of the competitive hydrogen evolution reaction (HER), and good durability over an operation period of 8 h. In hindsight, the study presented a low-cost and highly efficient catalyst design for achieving enhanced ammonia synthesis in alkaline media via the formation of defect-rich ultrathin MoS2@rGO nanostructures, consisting predominantly of an HER-hindering hexagonal 2H-MoS2 phase.

Quantifying intuition: Bayesian approach to figures of merit in EXAFS analysis of magic size clusters.

Analysis of the extended X-ray absorption fine structure (EXAFS) can yield local structural information in magic size clusters even when other structural methods (such as X-ray diffraction) fail, but typically requires an initial guess - an atomistic model. Model comparison is thus one of the most crucial steps in establishing atomic structure of nanoscale systems and relies critically on the corresponding figures of merit (delivered by the data analysis) to make a decision on the most suitable model of atomic arrangements. However, none of the currently used statistical figures of merit take into account the significant factor of parameter correlations. Here we show that ignoring such correlations may result in a selection of an incorrect structural model. We then report on a new metric based on Bayes theorem that addresses this problem. We show that our new metric is superior to the currently used in EXAFS analysis as it reliably yields correct structural models even in cases when other statistical criteria may fail. We then demonstrate the utility of the new figure of merit in comparison of structural models for CdS magic-size clusters using EXAFS data.

Structure-Property Relationship of Defect-Trapped Pt Single-Site Electrocatalysts for the Hydrogen Evolution Reaction.

Single-site catalysts (SSCs) have attracted significant research interest due to their high metal atom utilization. Platinum single sites trapped in the defects of carbon substrates (trapped Pt-SSCs) have been proposed as efficient and stable electrocatalysts for the hydrogen evolution reaction (HER). However, the correlation between Pt bonding environment, its evolution during operation, and catalytic activity is still unclear. Here, a trapped Pt-SSC is synthesized by pyrolysis of H2PtCl6 chemisorbed on a polyaniline substrate. In situ heated scanning transmission electron microscopy and temperature-dependent X-ray photoelectron spectroscopy clarify the thermally induced structural evolution of Pt during pyrolysis. The results show that the nitrogen in polyaniline coordinates with Pt ions and atomically disperses them before pyrolysis and traps Pt sites at pyridinic N defects generated during the substrate graphitization. Operando X-ray absorption spectroscopy confirms that the trapped Pt-SSC is stable at the HER working potentials but with inferior electrocatalytic activity compared with metallic Pt nanoparticles. First principle calculations suggest that the inferior activity of trapped Pt-SSCs is due to their unfavorable hydrogen chemisorption energy relative to metallic Pt(111) surfaces. These results further the understanding of the structure-property relationship in trapped Pt-SSCs and motivate a detailed techno-economic analysis to evaluate their commercial applicability.

Interfacial Chemistry in the Electrocatalytic Hydrogenation of CO2 over C-Supported Cu-Based Systems.

Operando soft and hard X-ray spectroscopic techniques were used in combination with plane-wave density functional theory (DFT) simulations to rationalize the enhanced activities of Zn-containing Cu nanostructured electrocatalysts in the electrocatalytic CO2 hydrogenation reaction. We show that at a potential for CO2 hydrogenation, Zn is alloyed with Cu in the bulk of the nanoparticles with no metallic Zn segregated; at the interface, low reducible Cu(I)-O species are consumed. Additional spectroscopic features are observed, which are identified as various surface Cu(I) ligated species; these respond to the potential, revealing characteristic interfacial dynamics. Similar behavior was observed for the Fe-Cu system in its active state, confirming the general validity of this mechanism; however, the performance of this system deteriorates after successive applied cathodic potentials, as the hydrogen evolution reaction then becomes the main reaction pathway. In contrast to an active system, Cu(I)-O is now consumed at cathodic potentials and not reversibly reformed when the voltage is allowed to equilibrate at the open-circuit voltage; rather, only the oxidation to Cu(II) is observed. We show that the Cu-Zn system represents the optimal active ensembles with stabilized Cu(I)-O; DFT simulations rationalize this observation by indicating that Cu-Zn-O neighboring atoms are able to activate CO2, whereas Cu-Cu sites provide the supply of H atoms for the hydrogenation reaction. Our results demonstrate an electronic effect exerted by the heterometal, which depends on its intimate distribution within the Cu phase and confirms the general validity of these mechanistic insights for future electrocatalyst design strategies.

Active and durable R2MnRuO7 pyrochlores with low Ru content for acidic oxygen evolution.

The production of green hydrogen in water electrolyzers is limited by the oxygen evolution reaction (OER). State-of-the-art electrocatalysts are based on Ir. Ru electrocatalysts are a suitable alternative provided their performance is improved. Here we show that low-Ru-content pyrochlores (R2MnRuO7, R = Y, Tb and Dy) display high activity and durability for the OER in acidic media. Y2MnRuO7 is the most stable catalyst, displaying 1.5 V at 10 mA cm-2 for 40 h, or 5000 cycles up to 1.7 V. Computational and experimental results show that the high performance is owed to Ru sites embedded in RuMnOx surface layers. A water electrolyser with Y2MnRuO7 (with only 0.2 mgRu cm-2) reaches 1 A cm-2 at 1.75 V, remaining stable at 200 mA cm-2 for more than 24 h. These results encourage further investigation on Ru catalysts in which a partial replacement of Ru by inexpensive cations can enhance the OER performance.

Lithium-Directed Transformation of Amorphous Iridium (Oxy)hydroxides To Produce Active Water Oxidation Catalysts.

The oxygen evolution reaction (OER) is crucial to future energy systems based on water electrolysis. Iridium oxides are promising catalysts due to their resistance to corrosion under acidic and oxidizing conditions. Highly active iridium (oxy)hydroxides prepared using alkali metal bases transform into low activity rutile IrO2 at elevated temperatures (>350 °C) during catalyst/electrode preparation. Depending on the residual amount of alkali metals, we now show that this transformation can result in either rutile IrO2 or nano-crystalline Li-intercalated IrOx. While the transition to rutile results in poor activity, the Li-intercalated IrOx has comparative activity and improved stability when compared to the highly active amorphous material despite being treated at 500 °C. This highly active nanocrystalline form of lithium iridate could be more resistant to industrial procedures to produce PEM membranes and provide a route to stabilize the high populations of redox active sites of amorphous iridium (oxy)hydroxides.

Highly active and stable OER electrocatalysts derived from Sr2MIrO6 for proton exchange membrane water electrolyzers.

Proton exchange membrane water electrolysis is a promising technology to produce green hydrogen from renewables, as it can efficiently achieve high current densities. Lowering iridium amount in oxygen evolution reaction electrocatalysts is critical for achieving cost-effective production of green hydrogen. In this work, we develop catalysts from Ir double perovskites. Sr2CaIrO6 achieves 10 mA cm-2 at only 1.48 V. The surface of the perovskite reconstructs when immersed in an acidic electrolyte and during the first catalytic cycles, resulting in a stable surface conformed by short-range order edge-sharing IrO6 octahedra arranged in an open structure responsible for the high performance. A proton exchange membrane water electrolysis cell is developed with Sr2CaIrO6 as anode and low Ir loading (0.4 mgIr cm-2). The cell achieves 2.40 V at 6 A cm-2 (overload) and no loss in performance at a constant 2 A cm-2 (nominal load). Thus, reducing Ir use without compromising efficiency and lifetime.

Elucidating the Formation and Structural Evolution of Platinum Single-Site Catalysts for the Hydrogen Evolution Reaction.

Platinum single-site catalysts (SSCs) are a promising technology for the production of hydrogen from clean energy sources. They have high activity and maximal platinum-atom utilization. However, the bonding environment of platinum during operation is poorly understood. In this work, we present a mechanistic study of platinum SSCs using operando, synchrotron-X-ray absorption spectroscopy. We synthesize an atomically dispersed platinum complex with aniline and chloride ligands onto graphene and characterize it with ex-situ electron microscopy, X-ray diffractometry, X-ray photoelectron spectroscopy, X-ray absorption near-edge structure spectroscopy (XANES), and extended X-ray absorption fine structure spectroscopy (EXAFS). Then, by operando EXAFS and XANES, we show that as a negatively biased potential is applied, the Pt-N bonds break first followed by the Pt-Cl bonds. The platinum is reduced from platinum(II) to metallic platinum(0) by the onset of the hydrogen-evolution reaction at 0 V. Furthermore, we observe an increase in Pt-Pt bonding, indicating the formation of platinum agglomerates. Together, these results indicate that while aniline is used to prepare platinum SSCs, the single-site complexes are decomposed and platinum agglomerates at operating potentials. This work is an important contribution to the understanding of the evolution of bonding environment in SSCs and provides some molecular insights into how platinum agglomeration causes the deactivation of SSCs over time.

Ivosidenib and Azacitidine in IDH1-Mutated Acute Myeloid Leukemia.

BACKGROUND: The combination of ivosidenib - an inhibitor of mutant isocitrate dehydrogenase 1 (IDH1) - and azacitidine showed encouraging clinical activity in a phase 1b trial involving patients with newly diagnosed IDH1-mutated acute myeloid leukemia. METHODS: In this phase 3 trial, we randomly assigned patients with newly diagnosed IDH1-mutated acute myeloid leukemia who were ineligible for intensive induction chemotherapy to receive oral ivosidenib (500 mg once daily) and subcutaneous or intravenous azacitidine (75 mg per square meter of body-surface area for 7 days in 28-day cycles) or to receive matched placebo and azacitidine. The primary end point was event-free survival, defined as the time from randomization until treatment failure (i.e., the patient did not have complete remission by week 24), relapse from remission, or death from any cause, whichever occurred first. RESULTS: The intention-to-treat population included 146 patients: 72 in the ivosidenib-and-azacitidine group and 74 in the placebo-and-azacitidine group. At a median follow-up of 12.4 months, event-free survival was significantly longer in the ivosidenib-and-azacitidine group than in the placebo-and-azacitidine group (hazard ratio for treatment failure, relapse from remission, or death, 0.33; 95% confidence interval [CI], 0.16 to 0.69; P = 0.002). The estimated probability that a patient would remain event-free at 12 months was 37% in the ivosidenib-and-azacitidine group and 12% in the placebo-and-azacitidine group. The median overall survival was 24.0 months with ivosidenib and azacitidine and 7.9 months with placebo and azacitidine (hazard ratio for death, 0.44; 95% CI, 0.27 to 0.73; P = 0.001). Common adverse events of grade 3 or higher included febrile neutropenia (28% with ivosidenib and azacitidine and 34% with placebo and azacitidine) and neutropenia (27% and 16%, respectively); the incidence of bleeding events of any grade was 41% and 29%, respectively. The incidence of infection of any grade was 28% with ivosidenib and azacitidine and 49% with placebo and azacitidine. Differentiation syndrome of any grade occurred in 14% of the patients receiving ivosidenib and azacitidine and 8% of those receiving placebo and azacitidine. CONCLUSIONS: Ivosidenib and azacitidine showed significant clinical benefit as compared with placebo and azacitidine in this difficult-to-treat population. Febrile neutropenia and infections were less frequent in the ivosidenib-and-azacitidine group than in the placebo-and-azacitidine group, whereas neutropenia and bleeding were more frequent in the ivosidenib-and-azacitidine group. (Funded by Agios Pharmaceuticals and Servier Pharmaceuticals; AGILE ClinicalTrials.gov number, NCT03173248.).

Operando XAFS investigation on the effect of ash deposition on three-way catalyst used in gasoline particulate filters and the effect of the manufacturing process on the catalytic activity.

Platinum group metals such as palladium and rhodium based catalysts are currently being implemented in gasoline particulate filter (GPF) autoexhaust after treatment systems. However, little is known about how the trapped particulate matter, such as the incombustible ash, interacts with the catalyst and so may affect its performance. Thisoperandostudy follows the evolution of the Pd found in two different model GPF systems: one containing ash components extracted from a GPF and another from a catalyst washcoat prior to adhesion onto the GPF. We show that the catalytic activity of the two systems vary when compared with a 0 g ash containing GPF. Compared to the 0 g ash sample the 20 g ash containing sample had a higher CO light off temperature, in addition, an oscillation profile for CO, CO2and O2was observed, which is speculated to be a combination of CO oxidation, C deposition via a Boudouard reaction and further partial oxidation of the deposited species to CO. During the ageing procedure the washcoat sample reduces NO at a lower temperature than the 0 g ash sample. However, post ageing the 0 g ash sample recovers and both samples reduce NO at 310 °C. In comparison, the 20 g ash GPF sample maintains a higher NO reduction temperature of 410 °C post ageing, implying that the combination of high temperature ageing and presence of ash has an irreversible negative effect on catalyst performance.

Contrasting the EXAFS obtained under air and H2 environments to reveal details of the surface structure of Pt-Sn nanoparticles.

Understanding the surface structure of bimetallic nanoparticles is crucial for heterogeneous catalysis. Although surface contraction has been established in monometallic systems, less is known for bimetallic systems, especially of nanoparticles. In this work, the bond length contraction on the surface of bimetallic nanoparticles is revealed by XAS in H2 at room temperature on dealloyed Pt-Sn nanoparticles, where most Sn atoms were oxidized and segregated to the surface when measured in air. The average Sn-Pt bond length is found to be ∼0.09 Šshorter than observed in the bulk. To ascertain the effect of the Sn location on the decrease of the average bond length, Pt-Sn samples with lower surface-to-bulk Sn ratios than the dealloyed Pt-Sn were studied. The structural information specifically from the surface was extracted from the averaged XAS results using an improved fitting model combining the data measured in H2 and in air. Two samples prepared so as to ensure the absence of Sn in the bulk were also studied in the same fashion. The bond length of surface Sn-Pt and the corresponding coordination number obtained in this study show a nearly linear correlation, the origin of which is discussed and attributed to the poor overlap between the Sn 5p orbitals and the available orbitals of the Pt surface atoms.

The Electrophilicity of Surface Carbon Species in the Redox Reactions of CuO-CeO2 Catalysts.

Electronic metal-support interactions (EMSI) describe the electron flow between metal sites and a metal oxide support. It is generally used to follow the mechanism of redox reactions. In this study of CuO-CeO2 redox, an additional flow of electrons from metallic Cu to surface carbon species is observed via a combination of operando X-ray absorption spectroscopy, synchrotron X-ray powder diffraction, near ambient pressure near edge X-ray absorption fine structure spectroscopy, and diffuse reflectance infrared Fourier transform spectroscopy. An electronic metal-support-carbon interaction (EMSCI) is proposed to explain the reaction pathway of CO oxidation. The EMSCI provides a complete picture of the mass and electron flow, which will help predict and improve the catalytic performance in the selective activation of CO2 , carbonate, or carbonyl species in C1 chemistry.

Effect of the Thermal Treatment of Fe/N/C Catalysts for the Oxygen Reduction Reaction Synthesized by Pyrolysis of Covalent Organic Frameworks.

A nitrogen-containing covalent organic framework obtained from the polymerization of 1,3-dicyanobenzene has been used as a starting material for the synthesis of Fe/N/C catalysts for the oxygen reduction reaction (ORR). In this work we report the effect of the thermal treatments on the nature and catalytic properties of the catalysts obtained after the thermal treatments. After the first thermal treatment, the catalysts obtained contain metallic iron and iron carbide particles, along with a minority fraction of inorganic FeN x sites. After acid leaching and a second thermal treatment, FeN x sites remain in the catalysts, along with a minor fraction of graphite-wrapped Fe3C particles. Both catalysts display high activity for the ORR, with the catalyst subjected to acid leaching and a second thermal treatment, 2HT-1,3DCB, displaying higher ORR activity and a lower production of H2O2. This observation suggests that iron particles, such as Fe3C, display ORR activity but mainly toward the two-electron pathway. On the contrary, FeN x ensembles promote the ORR via the four-electron pathway, that is, via H2O formation.

Mutant Isocitrate Dehydrogenase 1 Inhibitor Ivosidenib in Combination With Azacitidine for Newly Diagnosed Acute Myeloid Leukemia.

PURPOSE: Ivosidenib is an oral inhibitor of the mutant isocitrate dehydrogenase 1 (IDH1) enzyme, approved for treatment of IDH1-mutant (mIDH1) acute myeloid leukemia (AML). Preclinical work suggested that addition of azacitidine to ivosidenib enhances mIDH1 inhibition-related differentiation and apoptosis. PATIENTS AND METHODS: This was an open-label, multicenter, phase Ib trial comprising dose-finding and expansion stages to evaluate safety and efficacy of combining oral ivosidenib 500 mg once daily continuously with subcutaneous azacitidine 75 mg/m2 on days 1-7 in 28-day cycles in patients with newly diagnosed mIDH1 AML ineligible for intensive induction chemotherapy (ClinicalTrials.gov identifier: NCT02677922). RESULTS: Twenty-three patients received ivosidenib plus azacitidine (median age, 76 years; range, 61-88 years). Treatment-related grade ≥ 3 adverse events occurring in > 10% of patients were neutropenia (22%), anemia (13%), thrombocytopenia (13%), and electrocardiogram QT prolongation (13%). Adverse events of special interest included all-grade IDH differentiation syndrome (17%), all-grade electrocardiogram QT prolongation (26%), and grade ≥ 3 leukocytosis (9%). Median treatment duration was 15.1 months (range, 0.3-32.2 months); 10 patients remained on treatment as of February 19, 2019. The overall response rate was 78.3% (18/23 patients; 95% CI, 56.3% to 92.5%), and the complete remission rate was 60.9% (14/23 patients; 95% CI, 38.5% to 80.3%). With median follow-up of 16 months, median duration of response in responders had not been reached. The 12-month survival estimate was 82.0% (95% CI, 58.8% to 92.8%). mIDH1 clearance in bone marrow mononuclear cells by BEAMing (beads, emulsion, amplification, magnetics) digital polymerase chain reaction was seen in 10/14 patients (71.4%) achieving complete remission. CONCLUSION: Ivosidenib plus azacitidine was well tolerated, with an expected safety profile consistent with monotherapy with each agent. Responses were deep and durable, with most complete responders achieving mIDH1 mutation clearance.

Analysis of the atomic structure of CdS magic-size clusters by X-ray absorption spectroscopy.

Magic-size clusters are ultra-small colloidal semiconductor systems that are intensively studied due to their monodisperse nature and sharp UV-vis absorption peak compared with regular quantum dots. However, the small size of such clusters (<2 nm), and the large surface-to-bulk ratio significantly limit characterisation techniques that can be utilised. Here we demonstrate how a combination of EXAFS and XANES analyses can be used to obtain information about sample stoichiometry and cluster symmetry. Investigating two types of clusters that show sharp UV-vis absorption peaks at 311 nm and 322 nm, we found that both samples possess approximately 2 : 1 Cd : S ratio and have similar nearest-neighbour structural arrangements. However, both samples demonstrate a significant departure from the tetrahedral structural arrangement, with an average bond angle determined to be around 106.1° showing a bi-fold bond angle distribution. Our results suggest that both samples are quasi-isomers - their core structures have identical chemical compositions, but different atomic arrangements with distinct bond angle distributions.

Adsorption and activation of molecular oxygen over atomic copper(I/II) site on ceria.

Supported atomic metal sites have discrete molecular orbitals. Precise control over the energies of these sites is key to achieving novel reaction pathways with superior selectivity. Here, we achieve selective oxygen (O2) activation by utilising a framework of cerium (Ce) cations to reduce the energy of 3d orbitals of isolated copper (Cu) sites. Operando X-ray absorption spectroscopy, electron paramagnetic resonance and density-functional theory simulations are used to demonstrate that a [Cu(I)O2]3- site selectively adsorbs molecular O2, forming a rarely reported electrophilic η2-O2 species at 298 K. Assisted by neighbouring Ce(III) cations, η2-O2 is finally reduced to two O2-, that create two Cu-O-Ce oxo-bridges at 453 K. The isolated Cu(I)/(II) sites are ten times more active in CO oxidation than CuO clusters, showing a turnover frequency of 0.028 ± 0.003 s-1 at 373 K and 0.01 bar PCO. The unique electronic structure of [Cu(I)O2]3- site suggests its potential in selective oxidation.

Taxane resistance in prostate cancer is mediated by decreased drug-target engagement.

Despite widespread use of taxanes, mechanisms of action and resistance in vivo remain to be established, and there is no way of predicting who will respond to therapy. This study examined prostate cancer (PCa) xenografts and patient samples to identify in vivo mechanisms of taxane action and resistance. Docetaxel drug-target engagement was assessed by confocal anti-tubulin immunofluorescence to quantify microtubule bundling in interphase cells and aberrant mitoses. Tumor biopsies from metastatic PCa patients obtained 2 to 5 days after their first dose of docetaxel or cabazitaxel were processed to assess microtubule bundling, which correlated with clinical response. Microtubule bundling was evident in PCa xenografts 2 to 3 days after docetaxel treatment but was decreased or lost with acquired resistance. Biopsies after treatment with leuprolide plus docetaxel showed extensive microtubule bundling as did biopsies obtained 2 to 3 days after initiation of docetaxel or cabazitaxel in 2 patients with castration-resistant PCa with clinical responses. In contrast, microtubule bundling in biopsies 2 to 3 days after the first dose of docetaxel was markedly lower in 4 nonresponding patients. These findings indicate that taxanes target both mitotic and interphase cells in vivo and that resistance is through mechanisms that impair drug-target engagement. Moreover, the findings suggest that microtubule bundling after initial taxane treatment may be a predictive biomarker for clinical response.