Quantifying SIMS of Organic Mixtures and Depth Profiles-Characterizing Matrix Effects of Fragment Ions.

Sets of matrix factors, Ξ, are reported for the first time for secondary ions in secondary ion mass spectrometry for several binary organic systems. These show the interplay of the effects of ion velocity, fragment chemistry, and the secondary ion point of origin. Matrix factors are reported for negative ions for Irganox 1010 with FMOC or Irganox 1098 and, for both positive and negative ions, with Ir(ppy)2(acac). For Irganox 1010/FMOC, the Ξ values for Irganox 1010 fall with m/z, whereas those for FMOC rise. For m/z < 250, Ξ scales very approximately with (m/z)0.5, supporting a dependence on the ion velocity at low mass. Low-mass ions generally have low matrix factors but |Ξ| may still exceed 0.5 for m/z < 50. Analysis of ion sequences with addition or loss of a hydrogen atom shows that the Ξ values for Irganox 1010 and FMOC ions change by - 0.026 and 0.24 per hydrogen atom, respectively, arising from the changing charge transfer rate constant. This effect adds to that of velocity and may be associated with the nine times more hydrogen atoms in the Irganox 1010 molecule than in FMOC. For Irganox 1098/Irganox 1010, the molecular similarity leads to small |Ξ|, except for the pseudo molecular ions where the behavior follows Irganox 1010/FMOC. For Ir(ppy)2(acac)/Irganox 1010, the positive secondary ions show twice the matrix effects of negative ions. These data provide the first overall assessment of matrix factors in organic mixtures necessary for improved understanding for quantification and the precise localization of species. Graphical Abstract ᅟ.

SIMS of Organic Materials-Interface Location in Argon Gas Cluster Depth Profiles Using Negative Secondary Ions.

A procedure has been established to define the interface position in depth profiles accurately when using secondary ion mass spectrometry and the negative secondary ions. The interface position varies strongly with the extent of the matrix effect and so depends on the secondary ion measured. Intensity profiles have been measured at both fluorenylmethyloxycarbonyl-L-pentafluorophenylalanine (FMOC) to Irganox 1010 and Irganox 1010 to FMOC interfaces for many secondary ions. These profiles show separations of the two interfaces that vary over some 10 nm depending on the secondary ion selected. The shapes of these profiles are strongly governed by matrix effects, slightly weakened by a long wavelength roughening. The matrix effects are separately measured using homogeneous, known mixtures of these two materials. Removal of the matrix and roughening effects give consistent compositional profiles for all ions that are described by an integrated exponentially modified Gaussian (EMG) profile. Use of a simple integrated Gaussian may lead to significant errors. The average interface positions in the compositional profiles are determined to standard uncertainties of 0.19 and 0.14 nm, respectively, using the integrated EMG function. Alternatively, and more simply, it is shown that interface positions and profiles may be deduced from data for several secondary ions with measured matrix factors by simply extrapolating the result to Ξ = 0. Care must be taken in quoting interface resolutions since those measured for predominantly Gaussian interfaces with Ξ above or below zero, without correction, appear significantly better than the true resolution. Graphical Abstract ᅟ.

Determination of the sputtering yield of cholesterol using Arn(+) and C60(+(+)) cluster ions.

The sputtering yield of cholesterol films on silicon wafers is measured using Arn(+) and C60(+(+)) ions in popular energy (E) and cluster size (n) ranges. It is shown that the C60(+(+)) ions form a surface layer that stabilizes the film so that a well-behaved profile is obtained. On the other hand, the Arn(+) gas clusters leave the material very clean but, at room temperature, the layer readily restructures into molecular bilayers, so that, although a useful measure may be made of the sputtering yield, the profiles become much more complex. This restructuring does not occur at room temperature normally but results from the actions of the beams in the sputtering process for profiling in secondary ion mass spectrometry. Better profiles may be made by reducing the sample temperature to -100 °C. This is likely to be necessary for many lower molecular weight materials (below 1000 Da) to avoid the movement of molecules. Measurements for cholesterol films on 37 nm of amiodarone on silicon are even better behaved and show the same sputtering yields at room temperature as those films directly on silicon at -100 °C. The yields for both C60(+(+)) and Arn(+) fit the Universal Equation to a standard deviation of 11%.

Sampling Depths, Depth Shifts, and Depth Resolutions for Bi(n)(+) Ion Analysis in Argon Gas Cluster Depth Profiles.

Gas cluster sputter depth profiling is increasingly used for the spatially resolved chemical analysis and imaging of organic materials. Here, a study is reported of the sampling depth in secondary ion mass spectrometry depth profiling. It is shown that effects of the sampling depth leads to apparent shifts in depth profiles of Irganox 3114 delta layers in Irganox 1010 sputtered, in the dual beam mode, using 5 keV Ar2000⁺ ions and analyzed with Bi(q+), Bi3(q+) and Bi5(q+) ions (q = 1 or 2) with energies between 13 and 50 keV. The profiles show sharp delta layers, broadened from their intrinsic 1 nm thickness to full widths at half-maxima (fwhm's) of 8-12 nm. For different secondary ions, the centroids of the measured delta layers are shifted deeper or shallower by up to 3 nm from the position measured for the large, 564.36 Da (C33H46N3O5⁻) characteristic ion for Irganox 3114 used to define a reference position. The shifts are linear with the Bi(n)(q+) beam energy and are greatest for Bi3(q+), slightly less for Bi5(q+) with its wider or less deep craters, and significantly less for Bi(q+) where the sputtering yield is very low and the primary ion penetrates more deeply. The shifts increase the fwhm's of the delta layers in a manner consistent with a linearly falling generation and escape depth distribution function (GEDDF) for the emitted secondary ions, relevant for a paraboloid shaped crater. The total depth of this GEDDF is 3.7 times the delta layer shifts. The greatest effect is for the peaks with the greatest shifts, i.e. Bi3(q+) at the highest energy, and for the smaller fragments. It is recommended that low energies be used for the analysis beam and that carefully selected, large, secondary ion fragments are used for measuring depth distributions, or that the analysis be made in the single beam mode using the sputtering Ar cluster ions also for analysis.

Sputtering Yields for Mixtures of Organic Materials Using Argon Gas Cluster Ions.

The sputtering yield volumes of binary mixtures of Irganox 1010 with either Irganox 1098 or Fmoc-pentafluoro-L-phenylalanine (FMOC) have been measured for 5 keV Ar2000(+) ions incident at 45° to the surface normal. The sputtering yields are determined from the doses to sputter through various compositions of 100 nm thick, intimately mixed, layers. Because of matrix effects, the profiles for secondary ions are distorted, and profile shifts in depth of 15 nm are observed leading to errors above 20% in the deduced sputtering yield. Secondary ions are selected to avoid this. The sputtering yield volumes for the mixtures are shown to be lower than those deduced from a linear interpolation from the pure materials. This is shown to be consistent with a simple model involving the changing energy absorbed for the sputtering of intimate mixtures. Evidence to support this comes from the secondary ion data for pairs of the different molecules. Both binary mixtures behave similarly, but matrix effects are stronger for the Irganox 1010/FMOC system.

Depth resolution at organic interfaces sputtered by argon gas cluster ions: the effect of energy, angle and cluster size.

An analysis is presented of the effect of experimental parameters such as energy, angle and cluster size on the depth resolution in depth profiling organic materials using Ar gas cluster ions. The first results are presented of the incident ion angle dependence of the depth resolution, obtained at the Irganox 1010 to silicon interface, from profiles by X-ray photoelectron spectrometry (XPS). By analysis of all relevant published depth profile data, it is shown that such data, from delta layers in secondary ion mass spectrometry (SIMS), correlate with the XPS data from interfaces if it is assumed that the monolayers of the Irganox 1010 adjacent to the wafer substrate surface have an enhanced sputtering rate. SIMS data confirm this enhancement. These results show that the traditional relation for the depth resolution, FWHM = 2.1Y(1/3) or slightly better, FWHM = P(X)Y(1/3)/n(0.2), where n is the argon gas cluster size, and P(X) is a parameter for each material are valid both at the 45° incidence angle of the argon gas cluster sputtering ions used in most studies and at all angles from 0° to 80°. This implies that, for optimal depth profile resolution, 0° or >75° incidence may be significantly better than the 45° traditionally used, especially for the low energy per atom settings required for the best resolved profiles in organic materials. A detailed analysis, however, shows that the FWHM requires a constant contribution added in quadrature to the above such that there are minimal improvements at 0° or greater than 75°. A critical test at 75° confirms the presence of this constant contribution.

Improving secondary ion mass spectrometry C60(n+) sputter depth profiling of challenging polymers with nitric oxide gas dosing.

Organic depth profiling using secondary ion mass spectrometry (SIMS) provides valuable information about the three-dimensional distribution of organic molecules. However, for a range of materials, commonly used cluster ion beams such as C60(n+) do not yield useful depth profiles. A promising solution to this problem is offered by the use of nitric oxide (NO) gas dosing during sputtering to reduce molecular cross-linking. In this study a C60(2+) ion beam is used to depth profile a polystyrene film. By systematically varying NO pressure and sample temperature, we evaluate their combined effect on organic depth profiling. Profiles are also acquired from a multilayered polystyrene and polyvinylpyrrolidone film and from a polystyrene/polymethylmethacrylate bilayer, in the former case by using an optimized set of conditions for C60(2+) and, for comparison, an Ar2000(+) ion beam. Our results show a dramatic improvement for depth profiling with C60(2+) using NO at pressures above 10(-6) mbar and sample temperatures below -75 °C. For the multilayered polymer film, the depth profile acquired using C60(2+) exhibits high signal stability with the exception of an initial signal loss transient and thus allows for successful chemical identification of each of the six layers. The results demonstrate that NO dosing can significantly improve SIMS depth profiling analysis for certain organic materials that are difficult to analyze with C60(n+) sputtering using conventional approaches/conditions. While the analytical capability is not as good as large gas cluster ion beams, NO dosing comprises a useful low-cost alternative for instruments equipped with C60(n+) sputtering.

Ambient surface mass spectrometry using plasma-assisted desorption ionization: effects and optimization of analytical parameters for signal intensities of molecules and polymers.

Results are presented on the optimization and characterization of a plasma-assisted desorption ionization (PADI) source for ambient mass spectrometry. It is found that by optimizing the geometry we can increase ion intensities for valine and by tuning the plasma power we can also select a more fragmented or less fragmented spectrum. The temperature of the surface rises linearly with plasma power: at 19 W it is 71 °C and at 28 W it is 126 °C. To understand if the changes in signal intensity are related to thermal desorption, experiments using a temperature-controlled sample stage and low plasma power settings were conducted. These show markedly different signal intensities to experiments of equivalent surface temperature but higher plasma power, proving that the mechanisms of ionization and desorption are more complicated than just thermal processes. Four different polymers, poly(methyl methacrylate) (PMMA), poly(ethylene terephthalate) (PET), poly(lactic acid) (PLA), and poly(tetrafluoroethylene) (PTFE), are analyzed using PADI. Mass spectra are obtained from all the polymers in the negative ion mode and from PMMA and PLA in the positive ion mode. For each polymer, characteristic ions are identified showing the ability to identify materials. The ions are formed from bond cleavage with O and CH(2) as common adducts. Ions were detected up to m/z 1200 for PTFE.

Surface analysis using a new plasma assisted desorption/ionisation source for mass spectrometry in ambient air.

The authors report on a modified micro-plasma assisted desorption/ionisation (PADI) device which creates plasma through the breakdown of ambient air rather than utilising an independent noble gas flow. This new micro-PADI device is used as an ion source for ambient mass spectrometry to analyse species released from the surfaces of polytetrafluoroethylene, and generic ibuprofen and paracetamol tablets through remote activation of the surface by the plasma. The mass spectra from these surfaces compare favourably to those produced by a PADI device constructed using an earlier design and confirm that the new ion source is an effective device which can be used to achieve ambient mass spectrometry with improved spatial resolution.

Mass spectrometry and informatics: distribution of molecules in the PubChem database and general requirements for mass accuracy in surface analysis.

Mass spectrometry is a powerful tool for the analysis and identification of substances across a broad range of technologies from proteomics and metabolomics through to surface analysis methods used for nanotechnology. A major challenge has been the development of automated methods to identify substances from the mass spectra. Public chemical databases have grown over 2 orders of magnitude in size over the past few years and have become a powerful tool in informatics approaches for identification. We analyze the popular PubChem database in terms of the population of substances with mass when resolved with typical mass spectrometer mass accuracies. We also characterize the average molecule in terms of the mass excess from nominal mass and the modal mass. It is shown, in agreement with other studies, that for the identification of unknowns a mass accuracy of around 1 ppm is required together with additional filtering using isotope patterns. This information is an essential part of a framework being developed for experimental library-free interpretation of complex molecule spectra in secondary ion mass spectrometry.

The effect of electrospray solvent composition on desorption electrospray ionisation (DESI) efficiency and spatial resolution.

In desorption electrospray ionisation (DESI) the interaction between the electrospray and the surface is key to two important analytical parameters, the spatial resolution and the sensitivity. We evaluate the effect of the electrospray solvent type, organic solvent fraction with water, analyte solubility and substrate wettability on DESI erosion diameter and material transferral into useful ion signal. To do this five amino acids, glycine, alanine, valine, leucine and phenylalanine are prepared as thin films on three substrates, UV/ozone treated glass, glass and polytetrafluoroethylene (PTFE). Four different solvents, acetonitrile (ACN), methanol (MeOH), ethanol (EtOH) and propan-2-ol (IPA), are used with organic solvent fractions with water varying from 0.1 to 1. These model systems allow the solubility or wettability to be kept constant as other parameters are varied. Additionally, comparison with electrospray ionisation (ESI) allows effects of ionisation efficiency to be determined. It is shown that the DESI efficiency is linearly dependent on the solubility (for these materials at least) and for analytes with solubilities below 1.5 g kg(-1), additional strategies may be required for DESI to be effective. We show that the DESI erosion diameter improves linearly with organic solvent fraction, with an organic solvent fraction of 0.9 instead of 0.5 leading to a 2 fold improvement. Furthermore, this leads to a 35 fold increase in DESI efficiency, defined as the molecular ion yield per unit area. It is shown that these improvements correlate with smaller droplet sizes rather than surface wetting or ionisation.

Organic depth profiling of a nanostructured delta layer reference material using large argon cluster ions.

Cluster ion beams have revolutionized the analysis of organic surfaces in time-of-flight secondary ion mass spectrometry and opened up new capabilities for organic depth profiling. Much effort has been devoted to understanding the capabilities and improving the performance of SF(5)(+) and C(60)(n+), which are successful for many, but not all, organic materials. Here, we explore the potential of organic depth profiling using novel argon cluster ions, Ar(500)(+) to Ar(1000)(+). We present results for an organic delta layer reference sample, consisting of ultrathin "delta" layers of Irganox 3114 (approximately 2.4 nm) embedded between thick layers of Irganox 1010 (approximately 46 or 91 nm). This indicates that, for the reference material, major benefits can be obtained with Ar cluster ions, including a constant high sputtering yield throughout a depth of approximately 390 nm, and an extremely low sputter-induced roughness of <5 nm. Although the depth resolution is currently limited by an instrumental artifact, and may not be the best attainable, these initial results strongly indicate the potential to achieve high depth resolution and suggest that Ar cluster ions may have a major role to play in the depth profiling of organic materials.

Developing repeatable measurements for reliable analysis of molecules at surfaces using desorption electrospray ionization.

Desorption electrospray ionization (DESI) is a powerful ambient ionization technique that can provide high-sensitivity mass spectrometry information directly from surfaces at ambient pressure. Although a growing amount of research has been devoted to exploring different applications, there are few studies investigating the basic parameters and underpinning metrology. An understanding of these is crucial to develop DESI as the robust and reliable technique required for significant uptake by industry. In this work, we begin with a systematic study of the parameters affecting the repeatability, sensitivity, and rate of consumption of material with DESI. To do this we have developed a model sample consisting of a thin uniform film of controlled thickness of Rhodamine B on glass. This model sample allowed assessment of optimal sensitivity and spot shape under different conditions. In addition, it allowed us to study the surface in more detail to understand why and how each parameter affects these. Using the model sample to optimize the instrument parameters for DESI led to an absolute intensity repeatability of better than 15%, achieved over a period of 1 day. This model sample provides valuable insight into the electrospray-sample interaction and the desorption mechanism. Confocal microscopy of areas analyzed by DESI allow droplet distribution, material utilization, and spot size to be determined. Studying surface erosion also gives the erosion rate of material, analogous to the sputtering yield in secondary ion mass spectrometry. The results of the study provide a clear description that explains the differences observed with changing electrospray parameters allowing optimization of the technique, for both spatial resolution and sensitivity.

Analysis of the interface and its position in C60(n+) secondary ion mass spectrometry depth profiling.

C60(n+) ions have been shown to be extremely successful for SIMS depth profiling of a wide range of organic materials, causing significantly less degradation of the molecular information than more traditional primary ions. This work focuses on examining the definition of the interface in a C60(n+) SIMS depth profile for an organic overlayer on a wafer substrate. First it investigates the optimum method to define the organic/inorganic interface position. Variations of up to 8 nm in the interface position can arise from different definitions of the interface position in the samples investigated here. Second, it looks into the reasons behind large interfacial widths, i.e., poor depth resolution, seen in C60(n+) depth profiling. This work confirms that, for Irganox 1010 deposited on a wafer, the depth resolution at the Irganox 1010/substrate interface is directly correlated to the roughening of material. C60n+

TOF-SIMS: accurate mass scale calibration.

A study is presented of the factors affecting the calibration of the mass scale in time-of-flight secondary ion mass spectrometry (TOF-SIMS). At the present time, TOF-SIMS analysts using local calibration procedures achieve a rather poor relative mass accuracy of only 150 ppm for large molecules (647 u) whereas for smaller fragments of <200 u this figure only improves to 60 ppm. The instrumental stability is 1 ppm and better than 10 ppm is necessary for unique identification of species. The above experimental uncertainty can lead to unnecessary confusion where peaks are wrongly identified or peaks are ambiguously assigned. Here we study, in detail, the instrumental parameters of a popular single stage reflection TOF-SIMS instrument with ion trajectory calculations using SIMION. The effect of the ion kinetic energy, emission angle, and other instrumental operating parameters on the measured peak position are determined. This shows clearly why molecular and atomic ions have different relative peak positions and the need for an aperture to restrict ions at large emission angles. These data provide the basis for a coherent procedure for optimizing the settings for accurate mass calibration and rules by which calibrations for inorganics and organics may be incorporated. This leads to a new generic set of ions for mass calibration that improves the mass accuracy in our interlaboratory study by a factor of 5. A calibration protocol is developed, which gives a relative mass accuracy of better than 10 ppm for masses up to 140 u. The effects of extrapolation beyond the calibration range are discussed and a recommended procedure is given to ensure that accurate mass is achieved within a selectable uncertainty for large molecules. Additionally, we can alternatively operate our instrument in a regime with good energy discrimination (i.e., poor energy compensation) to study the fragmented energies of molecules. This leads to data that support previous concepts developed in G-SIMS.