Assessment of Regional Diagnostic Reference Levels in Dental Radiography in Tamil Nadu.

Aim: The aim of this article is to assess Tamil Nadu adult diagnostic reference levels (DRLs) by collecting radiation dose data from the four different dental modalities. Materials and Methods: The study was carried out using routine adult exposure settings in 131 intraoral, 75 panoramic, 35 cephalometric, and 10 dental cone beam computed tomography (CBCT) X-ray devices. DRLs were assessed for intraoral and extraoral (panoramic, cephalometric, and CBCT) examinations in terms of incident air kerma (Ka, i) and kerma area product (PKA), respectively. Air kerma measurements, for all dental units, were made using calibrated RTI black Piranha 557 dosimeter (RTI Electronics AB, Sweden). The dosimeter was kept at the exit cone of the X-ray tube and on the detector side of the X-ray unit for intraoral and extraoral air kerma measurements, respectively. The obtained air kerma in extraoral modalities is multiplied with the beam area to evaluate PKA. Results: The third quartile values calculated from the median for adult intraoral (mandibular molar), panoramic, cephalometric, and CBCT were 1.5 mGy, 116 mGycm2, 40 mGycm2, and 532 mGycm2, respectively. The proposed DRL in the present study was comparable to those reported in Germany, Greece, the UK, Japan, and Korea. Conclusion: This study revealed the need for dose management and radiation dose optimization, in various dental facilities in the state. It was also found that dental facilities employed with the digital type of detector are not always related to lower exposure.

ASSESSMENT OF ADULT DIAGNOSTIC REFERENCE LEVELS IN INTRAORAL RADIOGRAPHY IN TAMIL NADU REGION, INDIA.

In the present study, incident air kerma has been measured, for six intraoral examinations, for establishing regional adult diagnostic reference levels (DRLs), in intraoral radiography, in Tamil Nadu, India. A total of 131 units, both digital (semiconductor-based) and analog (film-based) radiography systems, were selected for the study. The third quartile values, for the six intraoral examinations selected for the present study, ranged from 1.2 to 2.0 mGy, for the adult settings. The results showed a wide range of patient doses existing across the clinics or hospitals studied. This is the primary study for the establishment of adult intraoral DRL, in Tamil Nadu, one of the major states of the country. Similar studies will be undertaken in other major states across the country to establish national DRLs in intraoral radiography in the country.

Assessment of Regional Pediatric Diagnostic Reference Levels for Panoramic Radiography Using Dose Area Product.

AIM: The current work aims to calculate dose area product (DAP) and to determine regional diagnostic reference level (DRL) for pediatric panoramic radiography in Tamil Nadu. MATERIALS AND METHODS: In this study, DAP was calculated after finding the product of air kerma on the detector side of scanner with the corresponding exposed area. The obtained DAP values were further analyzed, and DRL was calculated using Microsoft Excel. The study was carried out with routine pediatric exposure parameters. RESULTS: The obtained mean, range, and third quartile values for pediatric panoramic radiography are found to be 65 mGycm2, 11-148 mGycm2, and 82 mGycm2, respectively. The proposed DRL is comparable with the other countries' DRL. CONCLUSION: Based on the results of the present study, it was observed that there exists a wide difference in mean doses among the panoramic scanners. The variation in radiation doses between the clinics/hospitals and similar scanners suggests a large potential for optimization of panoramic procedures.

Assessment of Adult Diagnostic Reference Levels for Panoramic Radiography in Tamil Nadu Region.

AIM: The aim of this study was to calculate dose area product (DAP) and to determine diagnostic reference level (DRL) for adult panoramic procedures in Tamil Nadu. MATERIALS AND METHODS: In this study, air kerma on the front side of the secondary collimator was measured with a Black Piranha, RTI Electronics, Sweden and multiplied with the corresponding exposed area to calculate DAP. The obtained DAP values were further analyzed, and DRL was calculated using the Microsoft Excel software. The study was carried out with regular adult exposure parameters. RESULTS: The mean, range, and 3rd quartile values for 67 panoramic scanners in Tamil Nadu, India, were calculated as 94 mGycm2, 41 mGycm2-165 mGycm2, and 114.3 mGycm2, respectively. The results are comparable with other international studies. CONCLUSION: The present study suggests that further optimization can be achieved in many centers by the recruitment of professionally qualified radiographers and conducting periodic training programs on the optimization of exposure parameters. Considering this as the first study for the dental DRL assessment, further studies are suggested to establish national dental DRL in India.

A ring-based compensator IMRT system optimized for low- and middle-income countries: Design and treatment planning study.

PURPOSE: We propose a novel compensator-based IMRT system designed to provide a simple, reliable, and cost-effective adjunct technology, with the goal of expanding global access to advanced radiotherapy techniques. The system would employ easily reusable tungsten bead compensators that operate independent of a gantry (e.g., mounted in a ring around the patient). Thereby the system can be retrofitted to existing linac and cobalt teletherapy units. This study explores the quality of treatment plans from the proposed system and the dependence on associated design parameters. METHODS: We considered 60 Co-based plans as the most challenging scenario for dosimetry and benchmarked them against clinical MLC-based plans delivered on a linac. Treatment planning was performed in the Pinnacle treatment planning system with commissioning based on Monte Carlo simulations of compensated beams. 60 Co-compensator IMRT plans were generated for five patients with head-and-neck cancer and five with gynecological cancer and compared to respective IMRT plans using a 6 MV linac beam with an MLC. The dependence of dosimetric endpoints on compensator resolution, thickness, position, and number of beams was assessed. Dosimetric accuracy was validated by Monte Carlo simulations of dose distribution in a water phantom from beams with the IMRT plan compensators. RESULTS: The 60 Co-compensator plans had on average equivalent PTV coverage and somewhat inferior OAR sparing compared to the 6 MV-MLC plans, but the differences in dosimetric endpoints were clinically acceptable. Calculated treatment times for head-and-neck plans were 7.6 ± 2.0 min vs 3.9 ± 0.8 min (6 MV-MLC vs 60 Co-compensator) and for gynecological plans were 8.7 ± 3.1 min vs 4.3 ± 0.4 min. Plan quality was insensitive to most design parameters over much of the ranges studied, with no degradation found when the compensator resolution was finer than 6 mm, maximum thickness at least 2 tenth-value-layers, and more than five beams were used. Source-to-compensator distances of 53 and 63 cm resulted in very similar plan quality. Monte Carlo simulations suggest no increase in surface dose for the geometries considered here. Simulated dosimetric validation tests had median gamma pass rates of 97.6% for criteria of 3% (global)/3 mm with a 10% threshold. CONCLUSIONS: The novel ring-compensator IMRT system can produce plans of comparable quality to standard 6 MV-MLC systems. Even when 60 Co beams are used the plan quality is acceptable and treatment times are substantially reduced. 60 Co-compensator IMRT plans are adequately modeled in an existing commercial treatment planning system. These results motivate further development of this low-cost adaptable technology with translation through clinical trials and deployment to expand the reach of IMRT in low- and middle-income countries.

Assessment of Regional Pediatric Computed Tomography Dose Indices in Tamil Nadu.

The aim of this article is to assess Tamil Nadu pediatric computed tomography (CT) diagnostic reference levels (DRLs) by collecting radiation dose data for the most commonly performed CT examinations. This work was performed for thirty CT scanners installed in various parts of the Tamil Nadu region. The patient cohort was divided into two age groups: <1 year, and 1-5 years. CT dose indices were measured using a 10 cm3 pencil ion chamber with pediatric head and body polymethyl methacrylate phantoms. Dose data such as volumetric CT dose index (CTDIv) and dose length product (DLP) on a minimum of twenty average-sized pediatric patients in each category were recorded to calculate a mean site CTDIv and DLP value. The rounded 75th percentile was used to calculate a pediatric DRL for each hospital, and then region by compiling all results. Data were collected for 3600 pediatric patients. Pediatric CT DRL for two age groups: <1 year (CTDIv and DLP of head [20 mGy, 352 mGy.cm], chest [7 mGy, 120 mGy.cm] and abdomen [12 mGy, 252 mGy.cm]), and 1-5 years (CTDIv and DLP of head [38 mGy, 505 mGy.cm], chest [8 mGy, 132 mGy.cm] and abdomen [14 mGy, 270 mGy.cm]) for select procedures have been calculated. Proposed pediatric DRLs of CTDIv and DLP for head procedure were lower, and for chest and abdomen procedures were higher than European pediatric DRLs for both age groups.

Cost-effective pediatric head and body phantoms for computed tomography dosimetry and its evaluation using pencil ion chamber and CT dose profiler.

In the present work, a pediatric head and body phantom was fabricated using polymethyl methacrylate (PMMA) at a low cost when compared to commercially available phantoms for the purpose of computed tomography (CT) dosimetry. The dimensions of head and body phantoms were 10 cm diameter, 15 cm length and 16 cm diameter, 15 cm length, respectively. The dose from a 128-slice CT machine received by the head and body phantom at the center and periphery were measured using a 100 mm pencil ion chamber and 150 mm CT dose profiler (CTDP). Using these values, the weighted computed tomography dose index (CTDIw) and in turn the volumetric CTDI (CTDIv) were calculated for various combinations of tube voltage and current-time product. A similar study was carried out using standard calibrated phantom and the results have been compared with the fabricated ones to ascertain that the performance of the latter is equivalent to that of the former. Finally, CTDIv measured using fabricated and standard phantoms were compared with respective values displayed on the console. The difference between the values was well within the limits specified by Atomic Energy Regulatory Board (AERB), India. These results indicate that the cost-effective pediatric phantom can be employed for CT dosimetry.

Establishment of diagnostic reference levels in computed tomography for select procedures in Pudhuchery, India.

Computed tomography (CT) scanner under operating conditions has become a major source of human exposure to diagnostic X-rays. In this context, weighed CT dose index (CTDIw), volumetric CT dose index (CTDIv), and dose length product (DLP) are important parameter to assess procedures in CT imaging as surrogate dose quantities for patient dose optimization. The current work aims to estimate the existing dose level of CT scanner for head, chest, and abdomen procedures in Pudhuchery in south India and establish dose reference level (DRL) for the region. The study was carried out for six CT scanners in six different radiology departments using 100 mm long pencil ionization chamber and polymethylmethacrylate (PMMA) phantom. From each CT scanner, data pertaining to patient and machine details were collected for 50 head, 50 chest, and 50 abdomen procedures performed over a period of 1 year. The experimental work was carried out using the machine operating parameters used during the procedures. Initially, dose received in the phantom at the center and periphery was measured by five point method. Using these values CTDIw, CTDIv, and DLP were calculated. The DRL is established based on the third quartile value of CTDIv and DLP which is 32 mGy and 925 mGy.cm for head, 12 mGy and 456 mGy.cm for chest, and 16 mGy and 482 mGy.cm for abdomen procedures. These values are well below European Commission Dose Reference Level (EC DRL) and comparable with the third quartile value reported for Tamil Nadu region in India. The present study is the first of its kind to determine the DRL for scanners operating in the Pudhuchery region. Similar studies in other regions of India are necessary in order to establish a National Dose Reference Level.

Forward versus inverse planning in oropharyngeal cancer: A comparative study using physical and biological indices.

CONTEXT: Possible benefits of inverse planning. AIMS: To analyze possible benefits of inverse planning intensity modulated radiation therapy (IMRT) over field-in-field 3D conformal radiation therapy (FIF-3DCRT) and to evaluate the differences if any, between low (6 Million Volts) and high energy (15 Million Volts) IMRT plans. MATERIALS AND METHODS: Ten patients with squamous cell carcinoma of oropharynx, previously treated with 6 MV step and shoot IMRT were studied. V100, V33, V66 , mean dose and normal tissue complication probabilities (NTCP) were evaluated for parotid glands. Maximum dose and NTCP were the parameters for spinal cord. STATISTICAL ANALYSIS USED: A two-tailed t-test was applied to analyze statistical significance between the different techniques. RESULTS: For combined parotid gland, a reduction of 4.374 Gy, 9.343 Gy and 7.883 Gy were achieved for D100, D66 and D33, respectively in 6 MV-IMRT when compared with FIF-3DCRT. Spinal cord sparing was better in 6 MV-IMRT (40.963 ± 2.650), with an average reduction of maximum spinal cord dose by 7.355 Gy from that using the FIF-3DCRT technique. The uncomplicated tumor control probabilities values were higher in IMRT plans thus leading to a possibility of dose escalation. CONCLUSIONS: Though low-energy IMRT is the preferred choice for treatment of oropharyngeal cancers, FIF-3DCRT must be given due consideration as a second choice for its well established advantages over traditional conventioan technique.

Dosimetric comparison between bone marrow sparing intensity-modulated radiation therapy and conventional techniques in the treatment of cervical cancer: a retrospective study.

PURPOSE: To investigate enlargement of prostate volume by edema during brachytherapy seed implantation and develop a nomogram model to calculate air-kerma strength (AKS) required for implantation of the enlarged transient prostatic volume. MATERIALS AND METHODS: The prostate volume was measured prior and after seed implantation using trans-rectal ultrasound imaging in the operating room to obtain volume enlargement. A nomogram model was developed that calculates AKS required for implantation of the enlarged transient prostate volume with optimal dose coverage. RESULTS: The measured prostate enlargement in this study was up to 60% of the initial volume. The effective prostatic volume enlargement was calculated for three isotopes: 125I, 103Pd and 131Cs. The effective volume enlargement for 125I implants was relatively small (< 10%) because of its long half-life. For 103Pd and 131Cs with short half-lives, additional AKS up to 20% and 30%, respectively, might be required to provide appropriate dose coverage of possible enlarged prostatic volumes. CONCLUSIONS: Prostate volume enlargement should be considered to obtain optimal dose coverage particularly for short half-life isotopes such as 131Cs and 103Pd. The nomogram model developed in this work provides the AKS required for implants with a wide range of prostatic volume enlargements (5-100%) for three isotopes. KEYWORDS: prostate brachytherapy, nomogram, airkerma strength, edema, volume enlargement.

Influence of photon energy on the quality of prostate intensity modulated radiation therapy plans based on analysis of physical indices.

The goal of the present study was to study the effects of low- and high-energy intensity-modulated photon beams on the planning of target volume and the critical organs in cases of localized prostate tumors in a cohort of 8 patients. To ensure that the difference between the plans is due to energy alone, all other parameters were kept constant. A mean dose volume histogram (DVH) for each value of energy and for each contoured structure was created and was considered as completely representative for all patients. To facilitate comparison between 6-MV and 15-MV beams, the DVH-s were normalized. The different parameters that were compared for 6-MV and 15-MV beams included mean DVH, different homogeneity indices, conformity index, etc. Analysis of several indices depicts more homogeneous dose for 15-MV beam and more conformity for 6-MV beam. Comparison of all these parameters showed that there was little difference between the 6-MV and 15-MV beams. For rectum, 2 to 4 % more volume received high dose with the 6-MV beam in comparison with the 15-MV beam, which was not clinically significant, since in practice much tighter constraints are maintained, such that Normal Tissue Complication Probability (NTCP) is kept within 5 %. Such tighter constraints might increase the dose to other regions and other critical organs but are unlikely to increase their complication probabilities. Hence the slight advantages of 15-MV beam in providing benefits of better normal-tissue sparing and better coverage cannot be considered to outweigh its well-known risk of non-negligible neutron production.