Digital denture with mucostatic base and functional borders: A cast-free digital technique.

Digital complete dentures fabricated using a mucostatic impression, like intraoral scans, are desirable for their beneficial effect on long-term residual ridge stability but may have less retention than those fabricated with a mucocompressive impression. Border molding procedure may improve initial retention, thus favoring adaptation to new dentures, especially in cases where neuromuscular dysfunctions may diminish the patient's ability to cope with adapting to existing motor patterns or learn new ones. However, a mucocompressive impression may cause higher residual ridge resorption, thus resulting in a retention decrease over time. A desirable combination would be a digital denture with a mucostatic intaglio surface obtained from intraoral scans and functional borders. A cast-free digital workflow for that is demonstrated in this technical report.

Assessment of distortion of intraoral scans of edentulous mandibular arch made with a 2-step scanning strategy: A clinical study.

STATEMENT OF PROBLEM: Manufacturers of several intraoral scanners have recommended a 2-step strategy for scanning the edentulous mandible. The 2-step technique requires scanning one side first and then moving to the other side. However, whether inconsistency in stitching occurs that results in loss of accuracy or distortion is unclear. PURPOSE: The purpose of this clinical study was to measure the potential distortion of intraoral scans of edentulous mandibular arches made with a 2-step scanning strategy and to assess their differences with conventional impressions. MATERIAL AND METHODS: Twenty mandibular edentulous arches were scanned by 1 investigator with an intraoral scanner using a 2-step scanning strategy, and a corresponding polysulfide conventional impression was obtained. The conventional impression was then immediately scanned with the same intraoral scanner. The obtained standard tessellation language (STL) files were superimposed with a surface-matching software program. After a preliminary alignment, the STL meshes were trimmed and reoriented; then, the final alignment was carried out and meshes moved to a metrology software program where their mean distance was measured. In addition, a surface curve (SIOS) was traced on the intraoral scan from the right to left retromolar pad along the residual ridge and automatically projected onto to the conventional impression scan to obtain a new curve (SC). The mean distance between SIOS and SC was measured and recorded as an indicator of the distortion by considering the X-, Y-, and Z-axes and the overall 3-dimensional (3D) deviation. The analysis was performed for the full curve length and after dividing it into 6 regions of interest. Univariate and multivariate statistical analyses were used to investigate the significance of the extent of the mean 3D distance, as well as the effects of measurement positions (side and region) between and within patients on differences along the X-, Y-, and Z-axes (α=.05). RESULTS: The mean (-0.08 mm; standard error: 0.025) 3D distance between the intraoral scan and conventional impression was significantly different from zero (P=.003). No significant effect of the factor "side" was found by using generalized estimated equation models for the X-, Y-, and Z-axes, and global 3D deviations between SIOS and SC (P>.05), which appeared to exclude distortion. Conversely, a significant effect was found for the factor "region" (P<.05), with no significant differences (P>.05) between corresponding regions on the 2 sides. CONCLUSIONS: Intraoral scans of the edentulous mandibular arch made in a 2-step procedure did not exhibit significant distortion in comparison with conventional impressions.

The efficacy of a modified mandibular advancement device for OSA treatment in a group of adult patients.

OBJECTIVE: The Mandibular Advancement Device (MAD) is actually recommended for the treatment of Obstructive Sleep Apnea (OSA) with mild or moderate severity. The present study evaluated the effects of a fully customizable MAD-type device (It Makes You Sleep, IMYS), in patients with moderate-to-severe OSA. METHODS: Twenty-nine patients (15 men and 14 women; mean age 62, SD ±10 years) were retrospectively enrolled. Home Sleep Apnea Testing ;(HSAT) was performed for all patients at baseline (T0) and after three months (T1) of IMYS therapy. The analyzed respiratory parameters were: Apnea-Hypopnea Index (AHI), Oxygen Desaturation Index (ODI), Minimum Oxygen Saturation (minSO2) and Medium Oxygen Saturation (medSO2). RESULTS: From T0 to T1, a significant reduction of AHI and ODI was reported, as well as a significant increase of minSO2 and medSO2. CONCLUSION: The IMYS device could be an effective MAD appliance for treating moderate-to-severe OSA.

Effect of Fabrication Technology on the Accuracy of Surgical Guides for Dental-Implant Surgery.

BACKGROUND: The accuracy of surgical guides is a relevant factor in both surgical safety and prosthetic implications. The impact of widespread fabrication technologies (milling and 3D printing) was investigated. METHODS: Surgical guides manufactured by means of two specific milling and 3D-printing systems were digitized and compared in a 3D analysis with the digital file of the designed guides. The surface mean 3D distance (at the surface where the teeth and mucosa made contact) and the axial and linear deviations of the sleeves' housings were measured by means of a metrological software program. Univariate and multivariate statistical analyses were used to investigate the effects of the fabrication technology, type of support, and arch type on the surgical guides' accuracy. RESULTS: The median deviations of the intaglio surface in contact with the mucosa were significantly (p < 0.001) lower for the milled surgical guides (0.05 mm) than for the 3D-printed guides (-0.07 mm), in comparison with the reference STL file. The generalized estimated equation models showed that the axial deviations of the sleeves' housings (a median of 0.82 degrees for the milling, and 1.37 degrees for the 3D printing) were significantly affected by the fabrication technology (p = 0.011) (the milling exhibited better results), the type of support (p < 0.001), and the combined effect of the fabrication technology and the sleeve-to-crest angle (p = 0.003). The linear deviation (medians of 0.12 mm for the milling and 0.21 mm for the 3D printing) of their center points was significantly affected by the type of support (p = 0.001), with the milling performing slightly better than the 3D printing. CONCLUSIONS: The magnitude of the difference might account for a limited clinical significance.

Correlation between dental arch form and OSA severity in adult patients: an observational study.

BACKGROUND: The role of interdental widths and palatal morphology on the development of obstructive sleep apnea (OSA) has not been well investigated in adult patients yet. The aim of this paper was to assess the morphology of maxilla and mandibular dental arches on three-dimensional (3D) casts and to correlate these measurements with the severity of OSA. METHODS: Sixty-four patients (8 women and 56 men, mean age 52.4) with a diagnosis of mild-to-moderate OSA were retrospectively enrolled. On each patient, home sleep apnea test and 3D dental models were collected. Apnea-hypopnea index (AHI) and oxygen desaturation index (ODI) were recorded, as well as the dental measurements including inter-molar distance, anterior and posterior widths of maxillary and mandibular arches, upper and lower arch lengths, palatal height, and palatal surface area. The respiratory and dental variables were then correlated. RESULT: A statistically inverse correlation was found between ODI and anterior width of lower arch, maxillary arch length, palatal height, and palatal area. AHI showed a significant inverse correlation with anterior width of mandibular arch and maxillary length. CONCLUSION: A significant inverse correlation between maxillary and mandibular morphology and respiratory parameters was shown in the present paper.

Correction of Midline Deviation and Unilateral Crossbite Treated with Fixed Appliance.

The following case report describes the treatment of a 20-year-old man with dental and facial asymmetry. Patient presented upper dental midline shifted 3 mm to right side and the lower one 1 mm to left side, skeletal class I, molar class I and canine class III on the right side, molar class I and canine class II on the left side, and upper and lower crowding on teeth #12, #15, #22, #24, #34, and #35 in crossbite. The treatment plan provided four extractions: in the superior arch the right second and the left first premolar and in the lower arch first premolars on the left and right sides. Wire-fixed orthodontic device was used in combinations with coils to correct the midline deviation and to close post-extractive spaces, avoiding miniscrew implants. At the end of the treatment, optimal functional and aesthetic results were obtained: realignment of the midline improved facial symmetry, correction of the crossbite on both sides, and a good occlusal relationship.

Cast-free fabrication of a digital removable partial denture with a polyetheretherketone framework.

Digital workflows for removable partial dentures have enabled new machinable framework materials, including polyetheretherketone (PEEK). In addition, all denture components can be designed and manufactured digitally. Nonetheless, physical casts are still required for assembly of the components. The adoption of a cast-free fabrication procedure may enhance benefits, including a reduced number of procedures, faster processing, and reduced material waste. The purpose of this technical report was to demonstrate a workflow for the fabrication of a removable partial denture with a PEEK framework, milled teeth, and milled flanges, which uses intraoral scanning and no physical casts.

Accuracy of trial complete dentures fabricated by using fused deposition modeling 3-dimensional printing: An in vitro study.

STATEMENT OF PROBLEM: Three-dimensional (3D) printing technologies commonly used for trial complete dentures use photopolymerizing resins. Although effective, some clinical, process-related, and practical issues associated with them are still unclear. The option of using alternative printing technologies may help in overcoming limitations. PURPOSE: The purpose of this in vitro study was to evaluate the trueness of trial dentures fabricated by using 3D-printing fused deposition modeling (FDM). MATERIAL AND METHODS: Ten maxillary and 10 mandibular digital complete trial dentures designed from intraoral scans were fabricated from polylactic acid by using a FDM 3D-printer. Each denture was scanned, and the scans were compared with the digital file of the designed denture by means of a surface-matching software program. The mean distance (both signed and absolute) was measured and recorded for the intaglio surface, as well as for the entire denture surface. Statistical analysis was performed to investigate the significance of the extent of measured distances, as well as differences between intaglio and global deviations; subgroup analysis for arch type was also performed (α=.05). RESULTS: Mean values of the intaglio distance were not significantly different from zero (P=.223). The manufacturing accuracy of the intaglio surface was higher than that measured for the entire denture (P<.001), confirmed both by the averaged signed (0 mm and -0.028 mm, respectively) and the absolute mean deviations (0.06 mm and 0.08 mm, respectively). No significant differences were found between maxillary and mandibular trial dentures. CONCLUSIONS: 3D-printing may constitute a valid and practical option for accurate and affordable digital trial dentures.

Intaglio surface trueness of milled and 3D-printed digital maxillary and mandibular dentures: A clinical study.

STATEMENT OF PROBLEM: While the dimensional accuracy of the intaglio surface of a removable complete denture is key to its adaptation, comfort, and clinical performance, information on the ability of milling and 3D-printing workflows to accurately reproduce this surface is lacking. PURPOSE: The purpose of this clinical study was to compare the trueness of the intaglio surface of milled and 3D-printed removable complete digital dentures. MATERIAL AND METHODS: Intraoral scans were obtained from 14 participants for a total of 20 edentulous arches. Ten maxillary and 10 mandibular denture bases were then designed and fabricated with a completely digital workflow, both with milling and 3D-printing. Fabricated dentures were digitized with the same intraoral scanner used to obtain intraoral digital scans of the edentulous arches. Standard tessellation language (STL) files of the printed and milled denture bases were used for 3D analysis and comparisons with the STL file of the corresponding designed denture base. Specifically, a reverse engineering software program was used to trim and extract intaglio surfaces, align them, and measure their global mean 3D distance. In order to evaluate the homogeneity of production accuracy of each manufacturing process, the intaglio surfaces were also divided into several regions of interest and the corresponding 3D distances measured. Within- and between-group differences and maxillary and mandibular dentures differences were assessed with parametric and nonparametric tests (α=.05). RESULTS: Milling showed a global better trueness of the entire intaglio surface (-0.002 mm) than 3D-printing (0.018 mm), both for the whole data set (P<.001) and for maxillary (P=.032) or mandibular (P=.049) denture base subgroups. Within each fabrication technology, maxillary (P<.11) and mandibular dentures (P=.2) showed no significant difference in trueness. Measured deviations were significantly different from zero for the 3D-printed dentures (P<.001), but not for the milled dentures (P=.487). Additionally, for milled dentures, no significant difference in trueness was found among the 11 regions of interest identified for the maxillary dentures (P=.085) and the 13 regions of interest for the mandibular dentures (P=.211). Conversely, 3D-printing showed significant variations in trueness among the same zones of interest, both in maxillary (P<.001) and mandibular (P=.004) dentures. CONCLUSIONS: Within the limits of the manufacturing methodologies used for complete dentures, milling can provide a slightly better trueness of the intaglio surface than 3D-printing, with less variation across several zones of interest. However, given the magnitude of such differences, they may be reasonably considered to be of limited, if any, clinical significance.

Assessment of tooth displacement during the cast-free digital processing of milled dentures.

STATEMENT OF PROBLEM: Denture tooth displacement may have a significant impact on denture occlusion. This aspect has seldom been investigated, especially for digital denture processing techniques. PURPOSE: The purpose of this clinical study was to evaluate the accuracy of tooth position with milled digital dentures processed without physical casts. MATERIAL AND METHODS: Ten maxillary and 10 mandibular dentures designed from intraoral scans, milled, and processed without physical casts were investigated. The standard tessellation language (STL) files of the digitally designed dentures were compared with the scan of the dentures after processing (milling the denture base, milling teeth in a complete arch, and then bonding teeth into the base). The STL files were superimposed by using a surface-matching software program. After a preliminary alignment, the STL meshes were trimmed and reoriented; then, the final alignment was carried out by using the cameo surface. Six reference points (the mesiobuccal cusp on the most distal molar, the canine cusp, the middle of the incisal edge of the central incisor on both the left and the right side) were selected to measure tooth displacements along the X-, Y-, and Z-axes, corresponding (from the preliminary reorientation) to anteroposterior, mediolateral, and occlusal displacement, respectively. Tooth position accuracy was assessed by using median and interquartile range values. Univariate and multivariate statistical analyses were used to investigate the significance of the extent of displacements, as well as differences among displacement directions, reference teeth, side, and denture arch type (α=.05). RESULTS: Only the median (0.2 mm; interquartile range: 0.27 mm) occlusal displacement was significantly different from zero. A generalized estimated equation model addressing occlusal displacement as a dependent variable showed no significant effect of tooth type, side, or denture arch type, either alone or in combination. CONCLUSIONS: The tooth position of both maxillary and mandibular milled digital dentures processed without physical casts was accurate in the anteroposterior and mediolateral directions. Occlusal displacement seemed to be within the range of clinical acceptability; its consistency throughout the arch allowed optimization or compensation at the design or manufacturing step.

Three Dimensional Printed Surgical Guides: Effect of Time on Dimensional Stability.

PURPOSE: To analyze, in vitro, the dimensional stability over time of 3D-printed surgical guides. MATERIALS AND METHODS: Ten surgical guides, manufactured by digital light processing 3D-printing technology, were scanned immediately after post-processing and then after 5, 10, 15, and 20 days. The corresponding standard tessellation language (STL) files were used for comparison with the reference CAD project. Mean absolute deviation (MAD) of the intaglio surface, axial, and linear deviations of the sleeves' housings were measured. Generalized estimated equations models (α = 0.05) were used to investigate the effect of time. RESULTS: MAD of the teeth intaglio surface showed less variation (minimum: 0.002, maximum: 0.014 mm) than that of the mucosa (minimum: 0.026, maximum: 0.074 mm). Axial variations of the sleeves' housings on the sagittal (minimum: -0.008°, maximum: -0.577°) and frontal plane (minimum: -0.193°, maximum: 0.525°) changed with similar patterns, but opposite trends (decreasing for the former). Linear deviations of center points of the sleeves' housings had a shifting (minimum: -0.074, maximum: 0.02 mm) pattern with a decreasing tendency. Time after processing had a significant effect, either alone or nested with guides volume, on all outcomes of interest, except for MAD of the mucosa intaglio surface (p < 0.001), which was significantly affected only by the time-volume nested effect (p = 0.012). CONCLUSIONS: Within the limitations of the experimental design, postmanufacturing dimensional variations of surgical guides were statistically significant. Although limited, they are an additional source of variability affecting the overall accuracy of computer-guided surgery. As such, they should be addressed by further research.

Surgical guides for dental implants: Measurement of the accuracy using a freeware metrology software program.

PURPOSE: Manufacturing-related inaccuracies of surgical guides for static computer-aided implant surgery may contribute to the overall potential error in the obtained implant position. Measuring such inaccuracies before surgery may provide quality control assessment and improve the safety and outcomes of guided implant surgery. This technical report demonstrates a workflow to measure the accuracy of a surgical guide (at the intaglio surface and sleeve housing) using a freeware metrology software program. METHODS: The scan of a milled surgical guide was aligned to and compared with its reference computer-aided design model using a freeware metrology software program (GOM Inspect suite; GOM GmbH). The trueness of the internal surface of the surgical guide was measured as an indicator of adaptation to the supporting tissues. Additionally, some features were constructed to extract the plane at the sleeve entrance and sleeve axis and to set a local coordinate system on them. Linear and angular deviations between the planned and obtained sleeve axes were measured using this system. Such measurements, together with additional known data (sleeve offset and the planned implant length), allowed the estimation of linear errors in implant position at both the implant platform and apex by applying common geometric formulas, based on the assumption that all other sources of error in implant position could be effectively controlled during the surgical procedure. CONCLUSIONS: The proposed digital technique is a cost-effective approach for quality control of the inaccuracies of a surgical guide and predicts the related potential error in implant position.

OSA Wellness Scale (OWS): A New Health-Related Quality of Life Test in Obstructive Sleep Apnea Patients Treated with Mandibular Advancement Device.

Objectives: To present a new short self-test, called the OSA wellness scale (OWS), for assessing the health-related quality of life (HRQoL) changes in obstructive apnea syndrome (OSA) patients treated with mandibular advancement device (MAD). Methods: 51 OSA patients (8 women and 43 men, mean age 52.3) treated with a fully customizable MAD device (Protrusor) were retrospectively enrolled. Each patient received a home sleep apnea testing (HSAT) at baseline (T0) and after three months of MAD treatment (T1). Two self-test evaluations, the Epworth sleepiness scale (ESS), and OWS were also submitted at T0 and T1. The OWS was a short self-test of 8 questions for evaluating the daytime HRQoL. Patients gave an assessment from 0 to 3 for each question. At the end of the questionnaire, the patients had a score from 0 to 24, resulting from the sum of all 8 scores. The higher the score, the greater the patient's perceived state of discomfort. Results: At T1, a significant decrease in the oxygen desaturation index (ODI) and apnea-hypopnea index (AHI) was shown (p < 0.0001), while no significant changes in body mass index (BMI) were found. Both the ESS and the OWS records showed a significant reduction in daytime sleepiness and HRQoL (p < 0.0001). Conclusion: The OWS could be a useful method to verify and numerically compare the perceived quality of life in OSA patients, before and after MAD therapy.

Comparative cost-analysis for removable complete dentures fabricated with conventional, partial, and complete digital workflows.

STATEMENT OF PROBLEM: Comparative cost-analysis related to different manufacturing workflows for removable complete denture fabrication is seldom performed before the adoption of a new technology. PURPOSE: The purpose of this study was to compare the clinical and laboratory costs of removable complete dentures fabricated with a conventional (workflow C), a partial digital (workflow M), and a complete digital (workflow D) workflow and to calculate the break-even points for the implementation of digital technologies in complete denture fabrication. MATERIAL AND METHODS: Clinical and laboratory costs for each of the investigated workflows and the manufacturing options related to denture base and denture teeth fabrication were collected from 10 private Italian dental laboratories and clinics. The selected variables included the clinical and laboratory manufacturing time needed to complete each workflow (opportunity cost); costs for materials, labor, packaging, and shipping; and capital and fixed costs for software and hardware, including maintenance fees. The effect of manufacturing workflows and their options on the outcomes of interest was investigated by using generalized estimated equations models (α=.05). Cost minimization and sensitivity analysis were also performed, and break-even points were calculated for the equipment capital costs related to the implementation of workflows M and D. RESULTS: From a laboratory standpoint, workflows M and D and related manufacturing options significantly (P<.001) reduced manufacturing time (5.90 to 6.95 hours and 6.30 to 7.35 hours, respectively), and therefore the opportunity cost of each denture compared with workflow C. Workflow M allowed variable costs savings between 81 and 169 USD, while workflow D allowed for an additional saving of 34 USD. The sensitivity analysis showed that the break-even point related to the capital investment for the equipment needed to implement workflows M and D could be reached, depending on the manufacturing options adopted, between 170 and 933 dentures for workflow M and between 73 and 534 dentures for workflow D. From a clinical standpoint, workflows C and M were almost identical. Conversely, workflow D, which included intraoral scanning, required 1 fewer appointment, saving 0.6 hours of chairside time and about 14 USD for materials compared with M. CONCLUSIONS: Digital workflows (partial and complete digital workflows) were more efficient and cost-effective than the conventional method of fabricating removable complete dentures, with workflow D showing the lowest opportunity and variable costs and break-even point. Savings increased when stock denture teeth were replaced with milled denture teeth and still further with the adoption of 3-dimensionally (3D) printed denture teeth. Milling equipment and materials for denture base fabrication were more expensive than those for 3D-printing. Milling monobloc dentures reduced opportunity and labor costs but increased material cost.

Craniofacial morphology in patients with obstructive sleep apnea: cephalometric evaluation / Morfologia craniofacial em pacientes com apneia obstrutiva do sono: avaliação cefalométrica

Abstract Introduction: Obstructive sleep apnea is characterized by a reduced airflow through the upper airways during sleep. Two forms of obstructive sleep apnea are described: the central form and the obstructive form. The obstructive form is related to many factors, such as the craniofacial morphology. Objective: To evaluate the correlation between the morphology of the cranial base, of the mandible and the maxilla, and obstructive sleep apnea severity. Methods: Eighty-four patients, mean age of 50.4 years old; 73 males and 11 females with obstructive sleep apnea were enrolled in the present study. Patients with high body mass index and comorbidities were excluded. Lateral cephalograms and polysomnography were collected for each patient to evaluate the correlation between craniofacial morphology and obstructive sleep apnea severity. A Spearman's rho correlation test between cephalometric measurements and obstructive sleep apnea indexes was computed. Statistical significance was set at p < 0.05. Results: Patients with a severe obstructive sleep apnea presented a reduction of sagittal growth of both effective mandibular length and cranio-basal length. The mandibular length was the only variable with a statistical correlation with apnea-hypopnea index. Vertical dimension showed a weak correlation with the severity of obstructive sleep apnea. No correlation with maxillary sagittal dimension was shown. Conclusion: Obstructive sleep apnea severity may be correlated to mandibular and cranial base growth. Facial vertical dimension had no correlation with obstructive sleep apnea severity.

Resumo Introdução: A apneia obstrutiva do sono é caracterizada por um fluxo de ar reduzido nas vias aéreas superiores durante o sono. Duas formas de apneia são descritas: a forma central e a forma obstrutiva. A forma obstrutiva tem sido relacionada a vários fatores, como a morfologia craniofacial. Objetivo: Avaliar a correlação entre a morfologia da base do crânio, da mandíbula e da maxila e a gravidade da apneia obstrutiva do sono. Método: Foram incluídos no presente estudo 84 pacientes com apneia obstrutiva do sono, com média de 50,4 anos; 73 homens e 11 mulheres. Pacientes com alto índice de massa corpórea e comorbidades foram excluídos. Foram coletados cefalogramas laterais e polissonografia para cada paciente para avaliar a correlação entre a morfologia craniofacial e a gravidade da apneia. Foi computado o coeficiente de correlação de postos de Spearman (rho) entre medidas cefalométricas e índices de apneia obstrutiva do sono. A significância estatística foi estabelecida em p < 0,05. Resultados: Pacientes com apneia obstrutiva do sono grave apresentaram redução do crescimento sagital do comprimento mandibular efetivo e do comprimento crânio-basal. O comprimento mandibular foi a única variável que apresentou correlação estatística com o índice de apneia-hipopneia. A dimensão vertical mostrou uma fraca correlação com a gravidade da apneia. Não foi demonstrada correlação com a dimensão maxilar sagital. Conclusão: A gravidade da apneia obstrutiva do sono pode estar correlacionada ao crescimento da base mandibular e craniana. A dimensão facial vertical não apresentou correlação com a gravidade da apneia.

A new design of mandibular advancement device (IMYS) in the treatment of obstructive sleep apnea.

OBJECTIVE: The mandibular advancement device (MAD) is currently suggested in patients with mild to moderate obstructive sleep apnea (OSA). This study investigated the effects of a new fully customizable MAD-type device called, "It Makes You Sleep" (IMYS), in patients with mild to moderate OSA. METHODS: Sixteen patients (14 men and 2 women; mean age 62; SD ± 11 years) were retrospectively enrolled. Each patient received home sleep apnea testing (HSAT) at baseline (T0) and after three months (T1) of IMYS treatment. The Apnea-Hypopnea Index (AHI), the Oxygen Desaturation Index (ODI), the Minimum Oxygen Saturation (minSO2) and the Medium Oxygen Saturation (medSO2) were analyzed. RESULTS: From T0 to T1, the IMYS treatment showed a significant reduction of AHI and ODI and a significant increase of minSO2 and medSO2. CONCLUSION: The IMYS appliance is an effective device for treating mild or moderate OSA.

Removable Partial Dentures with Polyetheretherketone Framework: The Influence on Residual Ridge Stability.

PURPOSE: To provide, in a clinical case-control study, 1-year data on edentulous residual ridge dimensional changes for patients wearing removable partial dentures (RPD) with Polyetheretherketone (PEEK) framework, fabricated with a digital workflow, and a control group of untreated patients. MATERIALS AND METHODS: Ten patients were treated with PEEK RPD, and six controls were studied. Intraoral scans at baseline (T0) and after a median period of 1 year (T1) were superimposed, trimmed, and reoriented (T0r and T1r), moved to a metrology software, and realigned. A curve (C0) was then traced on T0r, along the residual ridge crest; its projection (C1) on T1r was obtained. The mean distance C0-C1 was the dependent variable of interest and represented the 1-year changes in the height of the edentulous ridge. In addition, mean 3D distance between T0 and T1 at each edentulous area was measured. Differences in these outcomes measured between RPD treated and control groups were statistically assessed. RESULTS: Twenty-six and 14 edentulous areas were investigated in the RPD treated and control groups, respectively. No significant differences were observed for potentially confounding variables, such as median follow-up time (12.5 vs. 13 months, respectively), the alignment accuracy between T0r and T1r (0.01 mm vs. 0 mm, respectively), the median number of remaining teeth (6 vs. 8.5, respectively), and the median length of edentulous areas (25.5 mm vs. 22.8 mm, respectively). For the outcomes of interest, no statistically significant difference was seen in the mean distance between C0 and C1 (i.e., changes in residual ridge height: -0.39 ± 0.52 mm vs. -0.52 ± 0.54 mm, respectively) or in the mean 3D distance at corresponding points of the denture bearing areas (-0.3 ± 0.46 mm vs. -0.4 ± 0.35, respectively). CONCLUSIONS: Although 1 year is a relatively short observation period, this clinical study shows that there are no short-term differences in edentulous residual ridge height and overall dimensions between patients wearing PEEK RPD, fabricated with a digital workflow, and controls without an RPD.

Craniofacial morphology in patients with obstructive sleep apnea: cephalometric evaluation.

INTRODUCTION: Obstructive sleep apnea is characterized by a reduced airflow through the upper airways during sleep. Two forms of obstructive sleep apnea are described: the central form and the obstructive form. The obstructive form is related to many factors, such as the craniofacial morphology. OBJECTIVE: To evaluate the correlation between the morphology of the cranial base, of the mandible and the maxilla, and obstructive sleep apnea severity. METHODS: Eighty-four patients, mean age of 50.4 years old; 73 males and 11 females with obstructive sleep apnea were enrolled in the present study. Patients with high body mass index and comorbidities were excluded. Lateral cephalograms and polysomnography were collected for each patient to evaluate the correlation between craniofacial morphology and obstructive sleep apnea severity. A Spearman's rho correlation test between cephalometric measurements and obstructive sleep apnea indexes was computed. Statistical significance was set at p < 0.05. RESULTS: Patients with a severe obstructive sleep apnea presented a reduction of sagittal growth of both effective mandibular length and cranio-basal length. The mandibular length was the only variable with a statistical correlation with apnea-hypopnea index. Vertical dimension showed a weak correlation with the severity of obstructive sleep apnea. No correlation with maxillary sagittal dimension was shown. CONCLUSION: Obstructive sleep apnea severity may be correlated to mandibular and cranial base growth. Facial vertical dimension had no correlation with obstructive sleep apnea severity.

Trueness of Intaglio Surface of Milled Digital Dentures Designed from Intraoral Scans.

PURPOSE: To asses trueness of the intaglio surface of milled dentures fabricated according to a fully digital protocol starting from intraoral scans in a clinical study by means of 3-dimensional (3D) digital analysis. MATERIALS AND METHODS: Ten maxillary and 10 mandibular dentures, designed from intraoral scans and milled in-house, were studied. Intraoral scans were compared with the scans of intaglio surface of milled dentures. To this end, they were aligned, trimmed and used in a metrology software to measure their mean 3D distance, absolute mean deviation, and other parameters. Measured differences for all parameters were statistically investigated. Subgroup analysis for the maxillary and mandibular dentures was performed using independent samples t-test or, in case of non-normal distribution, by means of Mann-Whitney test. RESULTS: Using a mean of 24.9 ±2.8 measurement points/mm2 , a mean 3D distance of 0.0006 ±0.007 mm between intraoral scans and the scans of the intaglio surface of milled dentures was measured. The corresponding absolute mean deviation was 0.055 ±0.032 for maxillary dentures and 0.061 ±0.016 for mandibular dentures; such a difference between arches was statistically significant (p = 0.035). CONCLUSIONS: Milled dentures fabricated using a fully digital protocol and intraoral scans have accurate intaglio surfaces. It is reasonable to assume that they may achieve an adequate fit.

Occlusal Plane Modification in Clear Aligners Treatment: Three Dimensional Retrospective Longitudinal Study.

The purpose of the present study was to evaluate: (i) maxillary occlusal plane changes after clear aligners therapy with a 3D measurement technique; and (ii) as a secondary outcome, if such changes were correlated to the patient's 1axilla-mandibular divergence. 3D maxillary models of 32 patients (7 males and 25 females; mean age 22.3 +/− 3.4 year) treated with clear aligners were analyzed. The angle (α) between a reference palatine plane and a maxillary occlusal plane was measured. Five angular cephalometric measurements (NSL/MP; PP-OP; OP-MP; PP-MP; PFH/AFH%) were performed and related to Δα. The subjects were further divided into three groups according to facial divergence. After aligner treatment, Δα increased in hyperdivergent patients and decreased in hypodivergent patients (p < 0.05). Δα showed a significant positive correlation with NSL/MP (rho = 0.44) and negative correlation with PFH/AFH% (rho = −0.53). Aligners treatment produced a counterlockwise rotation of the maxillary occlusal plane, even if this rotation occurs differently depending on divergence.