Experimental and Thermal Stress Field Numerical Simulation Study on Laser Metal Deposition of Ti-48Al-2Cr-2Nb Alloy.

The experimental and numerical simulation analysis of a TiAl alloy by laser metal deposition technology is presented in this paper. The research examines the macroscopic morphology, microstructure, and mechanical properties of samples as laser power varies. It also delves into how the temperature field and residual stress evolve under different laser powers. The results reveal that the microstructure of samples is mainly composed of α2-Ti3Al phase and a γ-TiAl phase and that the details of the microstructure are significantly affected by laser power. As laser power increases, coarse lamellar structure content increases, corresponding to a decrease in α2 phase content. The deposited layer hardness ranges from 550 HV to 600 HV, and the average deposition layer hardness decreases with increased laser power. Simulation results predict the molten pool's size, temperature, and residual stresses. A significant increase in the molten pool size is observed when the laser power exceeds 1000 W, and the measured molten pool depths correspond closely to simulation predictions. However, significant tensile stresses are generated in the deposition layer due to high cooling rates, mainly in the x direction. Cracks are observed on the surface of the deposition layer at all laser powers.

Laser cleaning of RTV coating on the insulator surface by using millisecond pulse lasers.

High-efficiency and high-quality removal of sulfurized silicone rubber from insulator surfaces is paramount for high-voltage power systems. To address this issue, and aiming to achieve precise and nondestructive cleaning of room temperature vulcanized (RTV) coatings, we selected millisecond laser cleaning technology in this study. Successful and efficient cleaning of the RTV coating was performed by adjusting laser parameters. Characterization techniques, including scanning electron microscopy, energy-dispersive x-ray spectroscopy, and confocal microscopy, were employed to comprehensively assess the cleaning effects and ensure the integrity of the substrate surface. The results indicate that by adjusting the scanning power combination of the high power of the millisecond pulse laser to 200 W and the low power of 150 W, the glass substrate surface maintains excellent roughness and micro-morphological features after laser cleaning, providing optimal conditions for subsequent processing and utilization. This research contributes an efficient and cost-effective solution to the insulation treatment process in high-voltage power systems.

Numerical Simulation of Temperature Characteristics and Graphitization Mechanism of Diamond in Laser Powder Bed Fusion.

Thermal damage to diamonds is a major limitation in laser powder bed fusion (LPBF) processing of metal matrix diamond composites. In this paper, a numerical simulation model was established to describe the thermal effect of the Diamond-CuSn10 composite on the LPBF process. The simulation results show that the temperature of the diamond presents a double-peak structure, and the double-peak temperature curve shape can be modulated by modifying the laser scanning offset and the size of the diamond powder. And it suggests that the heat of the diamond mainly comes from the transfer of the molten pool. Then, combined with the experimental phenomenon, the mechanism of diamond graphitization in the LPBF process is analyzed. It indicates that since the surface defects of the diamond inhibit the heat conduction of the diamond, the temperature accumulates on the surface, leading to the graphitization of the diamond. Finally, based on this model, the potential of Ti-coated diamonds to prevent and reduce thermal damage in the LPBF process has been extensively studied. It is found that a Ti coating with low thermal conductivity can effectively reduce diamond temperature and improve diamond graphitization resistance. This study can provide a good method and basis for the preliminary selection of LPBF process parameters and the understanding of the graphitization mechanism of diamond tools.

Toxicology Study of Single-walled Carbon Nanotubes and Reduced Graphene Oxide in Human Sperm.

Carbon-based nanomaterials such as single-walled carbon nanotubes and reduced graphene oxide are currently being evaluated for biomedical applications including in vivo drug delivery and tumor imaging. Several reports have studied the toxicity of carbon nanomaterials, but their effects on human male reproduction have not been fully examined. Additionally, it is not clear whether the nanomaterial exposure has any effect on sperm sorting procedures used in clinical settings. Here, we show that the presence of functionalized single walled carbon nanotubes (SWCNT-COOH) and reduced graphene oxide at concentrations of 1-25 µg/mL do not affect sperm viability. However, SWCNT-COOH generate significant reactive superoxide species at a higher concentration (25 µg/mL), while reduced graphene oxide does not initiate reactive species in human sperm. Further, we demonstrate that exposure to these nanomaterials does not hinder the sperm sorting process, and microfluidic sorting systems can select the sperm that show low oxidative stress post-exposure.

Nanofluidic Transport through Isolated Carbon Nanotube Channels: Advances, Controversies, and Challenges.

Owing to their simple chemistry and structure, controllable geometry, and a plethora of unusual yet exciting transport properties, carbon nanotubes (CNTs) have emerged as exceptional channels for fundamental nanofluidic studies, as well as building blocks for future fluidic devices that can outperform current technology in many applications. Leveraging the unique fluidic properties of CNTs in advanced systems requires a full understanding of their physical origin. Recent advancements in nanofabrication technology enable nanofluidic devices to be built with a single, nanometer-wide CNT as a fluidic pathway. These novel platforms with isolated CNT nanochannels offer distinct advantages for establishing quantitative structure-transport correlations in comparison with membranes containing many CNT pores. In addition, they are promising components for single-molecule sensors as well as for building nanotube-based circuits wherein fluidics and electronics can be coupled. With such advanced device architecture, molecular and ionic transport can be manipulated with vastly enhanced control for applications in sensing, separation, detection, and therapeutic delivery. Recent achievements in fabricating isolated-CNT nanofluidic platforms are highlighted, along with the most-significant findings each platform enables for water, ion, and molecular transport. The implications of these findings and remaining open questions on the exceptional fluidic properties of CNTs are also discussed.

On-demand and location selective particle assembly via electrophoretic deposition for fabricating structures with particle-to-particle precision.

Programmable positioning of 2 µm polystyrene (PS) beads with single particle precision and location selective, "on-demand", particle deposition was demonstrated by utilizing patterned electrodes and electrophoretic deposition (EPD). An electrode with differently sized hole patterns, from 0.5 to 5 µm, was used to illustrate the discriminatory particle deposition events based on the voltage and particle-to-hole size ratio. With decreasing patterned hole size, a larger electric field was required for a particle deposition event to occur in that hole. For the 5 µm hole, particle deposition began to occur at 10 V/cm where as an electric field of 15 V/cm was required for particles to begin depositing in the 2 µm holes. The likelihood of particle depositions continued to increase for smaller sized holes as the electric field increased. Eventually, a monolayer of particles began to form at approximately 20 V/cm. In essence, a voltage threshold was found for each hole pattern of different sizes, allowing fine adjustments in pattern hole size and voltage to control when a particle deposition event took place, even with the patterns on the same electrode. This phenomenon opens a route toward controlled, multimaterial deposition and assembly onto substrates without repatterning of the electrode or complicated surface modification of the particles. An analytical approach using the theories for electrophoresis and dielectrophoresis found the former to be the dominating force for depositing a particle into a patterned hole. Ebeam lithography was used to pattern spherical holes in precise configurations onto electrode surfaces, where each hole accompanied a polystyrene (PS) particle placement and attachment during EPD. The versatility of e-beam lithography was utilized to create arbitrary pattern configurations to fabricate particle assemblies of limitless configurations, enabling fabrication of unique materials assemblies and interfaces.

Hydrous ruthenium oxide nanoparticles anchored to graphene and carbon nanotube hybrid foam for supercapacitors.

In real life applications, supercapacitors (SCs) often can only be used as part of a hybrid system together with other high energy storage devices due to their relatively lower energy density in comparison to other types of energy storage devices such as batteries and fuel cells. Increasing the energy density of SCs will have a huge impact on the development of future energy storage devices by broadening the area of application for SCs. Here, we report a simple and scalable way of preparing a three-dimensional (3D) sub-5 nm hydrous ruthenium oxide (RuO2) anchored graphene and CNT hybrid foam (RGM) architecture for high-performance supercapacitor electrodes. This RGM architecture demonstrates a novel graphene foam conformally covered with hybrid networks of RuO2 nanoparticles and anchored CNTs. SCs based on RGM show superior gravimetric and per-area capacitive performance (specific capacitance: 502.78 F g(-1), areal capacitance: 1.11 F cm(-2)) which leads to an exceptionally high energy density of 39.28 Wh kg(-1) and power density of 128.01 kW kg(-1). The electrochemical stability, excellent capacitive performance, and the ease of preparation suggest this RGM system is promising for future energy storage applications.

Intertwined nanocarbon and manganese oxide hybrid foam for high-energy supercapacitors.

Rapid charging and discharging supercapacitors are promising alternative energy storage systems for applications such as portable electronics and electric vehicles. Integration of pseudocapacitive metal oxides with single-structured materials has received a lot of attention recently due to their superior electrochemical performance. In order to realize high energy-density supercapacitors, a simple and scalable method is developed to fabricate a graphene/MWNT/MnO2 nanowire (GMM) hybrid nanostructured foam, via a two-step process. The 3D few-layer graphene/MWNT (GM) architecture is grown on foamed metal foils (nickel foam) via ambient pressure chemical vapor deposition. Hydrothermally synthesized α-MnO2 nanowires are conformally coated onto the GM foam by a simple bath deposition. The as-prepared hierarchical GMM foam yields a monographical graphene foam conformally covered with an intertwined, densely packed CNT/MnO2 nanowire nanocomposite network. Symmetrical electrochemical capacitors (ECs) based on GMM foam electrodes show an extended operational voltage window of 1.6 V in aqueous electrolyte. A superior energy density of 391.7 Wh kg(-1) is obtained for the supercapacitor based on the GMM foam, which is much higher than ECs based on GM foam only (39.72 Wh kg(-1) ). A high specific capacitance (1108.79 F g(-1) ) and power density (799.84 kW kg(-1) ) are also achieved. Moreover, the great capacitance retention (97.94%) after 13 000 charge-discharge cycles and high current handability demonstrate the high stability of the electrodes of the supercapacitor. These excellent performances enable the innovative 3D hierarchical GMM foam to serve as EC electrodes, resulting in energy-storage devices with high stability and power density in neutral aqueous electrolyte.

Hybrid low resistance ultracapacitor electrodes based on 1-pyrenebutyric acid functionalized centimeter-scale graphene sheets.

Ultracapacitors are promising candidates for alternative energy storage applications since they can store and deliver energy at relatively high rates. Here, we present hybrid nanocarbon ultracapacitor electrodes with a low equivalent series resistance (ESR) of 7 ohms. 1-pyrenebutyric acid treated large-area single layer graphene (SLG) sheets covered with shortened multi-walled carbon nanotubes (MWNTs) have been utilized as highly conductive and percolated networks of hybrid carbon nanomaterial composites or thin films as ultracapacitor electrodes. Uniform centimeter scale single layer graphene sheets were produced via low pressure chemical vapor deposition using copper foil substrates and then subsequently modified by 1-pyrenebutyric acid functionalization. Chemically shortened MWNTs ranging in length of 200-500 nm, were deposited by drop casting on 1-pyrenebutyric acid functionalized SLG films. SLG/MWNT nancomposite hybrid films of different thicknesses were obtained by controlling the density of MWNT suspension. Surface morphology and nanostructure of the hybrid nanocomposites indicated relatively dense and homogeneous web-like networks. Specific capacitance values of the hybrid electrodes were substantially increased by 200% compared to those ultracapacitors fabricated using buckypaper electrodes. Average values of specific capacitance and energy density obtained were 140.64 F/g and 21.54 Wh/kg respectively. SLG/MWNT nanocomposite electrodes are very promising for future ultracapacitor devices with their low ESR value that is 95% lower than that of buckypaper based ultracapacitors.

Tuning electron transport in graphene-based field-effect devices using block co-polymers.

Graphene possesses many remarkable properties and shows promise as the future material for building nanoelectronic devices. For many applications such as graphene-based field-effect transistors (GFET), it is essential to control or modulate the electronic properties by means of doping. Using spatially controlled plasma-assisted CF(4) doping, the Dirac point shift of a GFET covered with a polycrystalline PS-P4VP block co-polymer (BCP) [poly(styrene-b-4-vinylpyridine)] having a cylindrical morphology can be controlled. By changing the chemical component of the microdomain (P4VP) and the major domain (PS) with the CF(4) plasma technique, the doping effect is demonstrated. This work provides a methodology where the Dirac point can be controlled via the different sensitivities of the PS and P4VP components of the BCP subjected to plasma processing.

Centimeter-scale high-resolution metrology of entire CVD-grown graphene sheets.

A high-throughput metrology method for measuring the thickness and uniformity of entire large-area chemical vapor deposition-grown graphene sheets on arbitrary substrates is demonstrated. This method utilizes the quenching of fluorescence by graphene via resonant energy transfer to increase the visibility of graphene on a glass substrate. Fluorescence quenching is visualized by spin-coating a solution of polymer mixed with fluorescent dye onto the graphene then viewing the sample under a fluorescence microscope. A large-area fluorescence montage image of the dyed graphene sample is collected and processed to identify the graphene and indicate the graphene layer thickness throughout the entire graphene sample. Using this metrology method, the effect of different transfer techniques on the quality of the graphene sheet is studied. It is shown that small-area characterization is insufficient to truly evaluate the effect of the transfer technique on the graphene sample. The results indicate that introducing a drop of acetone or liquid poly(methyl methacrylate) (PMMA) on top of the transfer PMMA layer before soaking the graphene sample in acetone improves the quality of the graphene dramatically over immediately soaking the graphene in acetone. This work introduces a new method for graphene quantification that can quickly and easily identify graphene layers in a large area on arbitrary substrates. This metrology technique is well suited for many industrial applications due to its repeatability and flexibility.

Label free DNA detection using large area graphene based field effect transistor biosensors.

We describe the fabrication of highly sensitive graphene based field effect transistor (FET) biosensors with a cost-effective approach and their application in label-free Deoxyribonucleic acid (DNA) detection. Chemical vapor deposition (CVD) grown graphene layers were used to achieve mass production of FET devices via conventional photolithographic patterning. Non-covalent functionalization of the graphene layer with 1-Pyrenebutanoic acid succinimidyl ester ensures high conductivity and sensitivity of the FET device. The present device could reach a detection limit as low as 3 x 10(-9) M.

Seeded growth of uniform Ag nanoplates with high aspect ratio and widely tunable surface plasmon bands.

Silver nanoplates with an extremely high aspect ratio (up to over 400) and a widely tunable surface plasmon resonance (SPR) band have been successfully synthesized by combining the concepts of selective ligand adhesion and seeded growth. Citrate ligands are used as the sole surfactant to effectively block overgrowth on the basal {111} facets and only allow growth in the lateral direction. By slowing down the reaction rate using Ag-citrate complex as precursor, the thin nature of Ag nanoplates is maintained with the edge length grown up to 4 µm, which ensures the high aspect ratio and the widely tunable SPR band. We also observe a size distribution focusing effect that helps to produce uniform nanoplates as well as narrow SPR bands over a wide range, which is important in many practical applications.

High yield synthesis of bracelet-like hydrophilic Ni-Co magnetic alloy flux-closure nanorings.

A simple solvothermal method has been discovered to synthesize single-walled flux-closure Ni-Co magnetic alloy nanorings in high yield, which are directly fabricated in a reaction solution and able to chronically exist in solution.